Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A series of two-stage torsion experiments on Carrara marble were conducted to constrain the influence of known prior deformation on rheological response and microstructural evolution. Comparison with previous experimental data on Carrara marble flow and fabric evolution during single-stage torsion deformation experiments provided direct insights into the significance of initial deformation at various conditions. Our experiments were conducted at 727 degrees C temperature and 300 MPa confining pressure, while maintaining a constant strain rate of 3 x 10(-4) s(-1) on the periphery of the cylindrical samples. Under these conditions, the marble is known to deform in power-law (n = 6-10) ductile flow. All torsion experiments were performed with a Paterson type gas-medium testing machine equipped with a torsion actuator module.;Prior (D1) and subsequent (D2) deformation are accomplished by two torsion experiments in sequence on same sample segments. The effect of D1 strain history is investigated during D2 by applying counter-clockwise torsion to a sandwich sample consisting of three segments with different D1 rotation sense. D2 samples experienced continued, first and reversed shearing deformation in top, centre and bottom segments, respectively. D2 bulk strain was chosen equal to D1 strain in top and bottom segments.;D1 experiments followed the typical single-stage deformation behaviour of Carrara marble under the applied experimental conditions. Yielding was followed by strain hardening until a peak stress was reached at a shear strain around 1, after which work softening occurred. Weakening gradually evolved into a constant stress regime. During hardening, a shear microstructure and crystallographic preferred orientation (CPO) developed. Afterwards the volume fraction of smaller dynamic recrystallised grains increased continuously, resulting in a recrystallisation microstructure and CPO at shear strains of 5 and higher. The new D2 experiments displayed a strain variation between homogeneously deformed sample segments that increased with increasing D1 strain. The stress-strain behaviour of the D2 bulk sandwich samples showed less pronounced work-hardening and -softening when compared with single-stage deformation experiments. Furthermore, constant flow stress was attained at increasingly lower strain with increasing D1 strain. In most D2 segments, fabric development is equivalent to single-stage experiments at corresponding absolute strain. The fabrics differed markedly from those in single-stage experiments in the case of reversed two-stage deformation at moderate strain (D1 shear strain 1 and 2.6). Experiments show that grain shape by shearing of relict grains is defined by finite strain and thus affected by strain reversal. Recrystallisation is controlled by absolute strain and not influenced by strain reversal.
ISSN: 0040-1951

hal-00617686
https://hal.archives-ouvertes.fr/hal-00617686
DOI : 10.1016/j.tecto.2010.09.029

Éditeur(s) : HAL CCSD Presses Universitaires de Louvain (distribution I6DOC/CIACO)
Résumé : In French. 10 pages, 5 figures, LaTeX 2e using EPSF and custom package taln2006.sty (designed by Pierre Zweigenbaum, ATALA). Proceedings of the 13th annual French-speaking conference on Natural Language Processing: `Traitement Automatique des Langues Naturelles' (TALN 2006), Louvain (Leuven), Belgium, 10-13 April 2003
National audience
We propose a theoretical framework within which information on the vocabulary of a given corpus can be inferred on the basis of statistical information gathered on that corpus. Inferences can be made on the categories of the words in the vocabulary, and on their syntactical properties within particular languages. Based on the same statistical data, it is possible to build matrices of syntagmatic similarity (bigram transition matrices) or paradigmatic similarity (probability for any pair of words to share common contexts). When clustered with respect to their syntagmatic similarity, words tend to group into sublanguage vocabularies, and when clustered with respect to their paradigmatic similarity, into syntactic or semantic classes. Experiments have explored the first of these two possibilities. Their results are interpreted in the frame of a Markov chain modelling of the corpus' generative processe(s): we show that the results of a spectral analysis of the transition matrix can be interpreted as probability distributions of words within clusters. This method yields a soft clustering of the vocabulary into sublanguages which contribute to the generation of heterogeneous corpora. As an application, we show how multilingual texts can be visually segmented into linguistically homogeneous segments. Our method is specifically useful in the case of related languages which happened to be mixed in corpora.
Verbum ex machina : Actes de la 13ème conférence annuelle sur le Traitement Automatique des Langues Naturelles
Louvain (Leuven), Belgium

hal-00327607
https://hal.archives-ouvertes.fr/hal-00327607
ARXIV : 0810.1212

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
The association of experimental data showing that the plastic deformation of olivine, the main constituent of the upper mantle, is highly anisotropic and the ubiquitous seismic anisotropy in the upper mantle, which indicates that olivine crystals show coherent orientations over scales of tens to hundreds of kilometers, implies that the long-term deformation in the upper mantle is anisotropic. We propose a multiscale approach, based on a combination of finite element and homogenization techniques, to model the deformation of a lithospheric plate while fully considering the mechanical anisotropy stemming from a strain-induced orientation of olivine crystals in the mantle. This multiscale model explicitly takes into account the evolution of crystal preferred orientations (CPO) of olivine and of the mechanical anisotropy during the deformation. We performed a series of numerical experiments simulating the uniaxial extension of a homogeneous (100% olivine) but anisotropic plate to test the role of the olivine CPO on the plate mechanical behavior and the link between CPO and mechanical anisotropy evolution. Even for this simple solicitation, different orientations and intensity of the initial olivine CPO result in variable plate strengths and deformation regimes. A plate with an initial CPO where the olivine [100] and [010] axes are concentrated at 45 degrees to the extension direction has high resolved shear stresses on the easy (010)[100] and (001)[100] slip systems of olivine. This results in low strength and in deformation by transtension. Plates with an initial CPO where the maximum of [100] axes is parallel or normal to the extension direction show a high initial strength. Isotropic plates have an intermediate behavior. The progressive rotation of olivine [100] axes toward the imposed stretching direction results in hardening in all models, except in those characterized by an initial concentration of olivine [100] axes normal to the imposed extension, in which softening is followed by hardening.
ISSN: 1525-2027

hal-00420063
https://hal.archives-ouvertes.fr/hal-00420063
DOI : 10.1029/2009GC002423

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Longmen Shan (Sichuan, China) is characterised by an unusual morphology which results from a Triassic prism tectonics and a more recent Neogene thick-skin thrusting. Among its specific features is the high elevation of the internal zones in continuity with the Songpan Garze fold-and-thrust belt (SG), which is associated with an abrupt 20 km Moho offset between the Sichuan Basin and the Tibetan plateau as revealed by the analysis of teleseismic data acquired by a dense seismic network. The jump in crustal thickness is located at the apex of the Wenchuan shear zone (WSZ) and marks the western boundary of the metamorphosed units of SG characterized by temperatures varying from 590 degrees C down to 300 degrees C as commonly observed in mature accretionary wedges. Both the structural style marked by intense shortening in tight kink folds and geophysical data suggest the presence of an horizontal discontinuity at similar to 15 km depth over a thick crust (similar to 63 km).;The Longmen Shan east of the WSZ is characterized by thick-skin detachment which thrusts the internal sedimentary units and the Proterozoic basement over the series of the Sichuan Basin deposited on a thinner crust of similar to 44 km thick. The major front is the Beichuan Fault Zone (BFZ) which brought the internal zones onto Triassic and Jurassic series with lower temperatures (less than 400 degrees C). Locally, temperatures of similar to 425 degrees C are found just below the klippes.;These results are in agreement with an original contact of the SG zone represented by an accretionary wedge of sediments thrusted over the margin of the continental crust of the Yangtze craton in the early stage (Indosinian) of the evolution. The present-day slow E-W component of the convergence, added to the difference in crustal thickness caused the Yangtze crust to indent the Songpan Tibetan crust which was softened by a high thermal regime. As a response the edge of the Tibet crust was inflated to the bottom (up to 70 km), whereas to the top, the crystalline massif were exhumed and pushed the deformation eastward as emerging and blind thrusts. This configuration reflects a moderate shortening of the crust which behaves as a soft thick material abutting the resistant and cold Yangtze crust.
ISSN: 0040-1951

hal-00534849
https://hal.archives-ouvertes.fr/hal-00534849
DOI : 10.1016/j.tecto.2010.03.018

Éditeur(s) : HAL CCSD
Résumé : International audience
In the external Western Alps, the collision started with the shortening of the proximal European (Dauphinois) margin. One peculiar feature is the crustal thickening that finally led to the exhumation of the basement External Crystalline Massifs (ECM) during the Neogene. In these massifs, various age of shortening, structural style and sequence of deformation have been proposed leading to different kinematics along the Alpine arc that in turn do not imply the same crustal/lithospheric strength. In this contribution, we present new structural and microstructural data along with Ar/Ar ages from field studies in the Oisans-Grandes Rousses massifs, between Grenoble and Briançon). From balanced cross-sections, we show that about half of the external zone crustal shortening is accommodated within the ECM with similar Ar/Ar ages in all massifs. Furthermore, the shear zones present very large thicknesses (several hundred meters) and do not reactivated either the inherited Liassic normal faults or the Variscan foliation. Finally, the main shortening structures are localized beneath inherited Liassic syn-rift basins. These results suggest that the crust was weak during its shortening. Such behavior is most likely due to the combination of several factors: the crust burial (below the overthrusting internal units) down to about 10km, the presence of weak inherited syn-rift basins, and the strain softening in shear zones that evolve in mica-rich phyllonites. These results are consistent with the studies in the Aar massif and should most likely apply to the Mont Blanc massif, whose relationships with its cover are still debated.
EGU General Assembly
Vienne, Austria

insu-00839426
https://hal-insu.archives-ouvertes.fr/insu-00839426
BIBCODE : 2013EGUGA..15.8837B

Éditeur(s) : HAL CCSD
Résumé : International audience
In this paper, we present a novel method for recognition of handwritten sketches. Unlike previous approaches, we focus on online retrieval and ability to build our model incrementally, thus we do not need to know all the data in advance and we can achieve very good recognition results after as few as 15 samples. The method is composed of two main parts: feature representation and learning and recognition. In feature representation part, we utilize SIFT-like feature descriptors in combination with soft response Bag-of-Words techniques. Descriptors are extracted locally using our novel sketch-specific sampling strategy and for support regions we follow patch-based approach. For learning and recognition, we use a novel technique based on fuzzy-neural networks, which has shown good performance in incremental learning. The experiments on state-of-the-art benchmarks have shown promising results.
17th Biennial Conference of the International Graphonomics Society
Pointe-à-Pitre, Guadeloupe

hal-01166497
https://hal.univ-antilles.fr/hal-01166497
https://hal.univ-antilles.fr/hal-01166497/document
https://hal.univ-antilles.fr/hal-01166497/file/IGS_2015_submission_37.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fromthe Proterozoic to the Quaternary, the evolution of the Earthwas characterised by recurrent periods of glaciation.However, the margins of many ancient ice-sheets are poorly defined on palaeogeographic reconstructions.The extent and outlines of ancient ice sheets can be better understood through careful documentation ofsediments deposited at the ice-sheet margin. An outstanding example is provided herein based on an end-Ordovician archive in Libya (Tihemboka area, Murzuq Basin). The four sets of structures include: i) subglacialglaciotectonic structures and soft sediment deformations from flowing glacier ice, such as intraformational glacialstriae, intraformational deformation (shear planes, sheath folds), normal microfaults, and large-scaleglaciotectonic folds-and-thrusts; (ii) structures resulting from overpressured subglacial (meltwater) flowssuch as clastic dykes and tunnel valleys; (iii) proglacial depositional structures and facies related to highmagnitudemeltwater floods such as sandstone intraclasts, large-scale bedforms resulting from supercriticalflows, climbing-dune cross-stratification and kettle holes; and (iv) deformation structures resulting from freefloating and nonglacier ice such as ice-keel scours and ice-crystal marks. Such a set of structures points to anice-marginal (essentially continental) depositional setting, and provides an excellent suite of criteria to identifymargins of ancient ice sheets in the stratigraphic record. At a regional scale, a reconstruction through time andspace of the related depositional wedge is proposed. This corresponded to a seismic-scale (N120 m in thickness,40 km in length) ice-marginal wedge in front of an essentially warm-based ice-sheet inducing concomitantlarge-scale glaciotectonic deformation, glacial basin and tunnel valley downcuttings. The related ice-front wasassociated with high-energy meltwater flows feeding a network of deeply incised proglacial channels downstreamand, beyond them, a fluvioglacial deltaic system. Shallow ice-marginal permafrost most likely affectedthe depositional wedge. At a larger scale, the Tihemboka ice-marginal wedge is interpreted as related to a stillstandperiod over the Gondwana platform, developed over an estimated interval of a few thousands of years.Based on these data, the conditions that arose in a particularly favourable context for the development, the preservationand the identification of ice-marginal wedges in the geological record are reviewed. Significantmeltwater-derived sediment deposition and aggradation in an accommodation space resulting either frompreglacial inheritance, glacial downcuttings and/or glacio-isostatic lithospheric flexure, or active tectonic subsidence(>1 Myr) are required for their formation and subsequent preservation.
ISSN: 0012-8252

insu-01184739
https://hal-insu.archives-ouvertes.fr/insu-01184739
DOI : 10.1016/j.earscirev.2015.06.006

Éditeur(s) : HAL CCSD Cambridge University Press (CUP)
Résumé : International audience
Diverse, abundant and usually well-preserved communities of skeletal organisms occur in the lower Pleistocene (Gelasian) siliciclastic deposits of the Greek island of Rhodes. Benthic foraminifers, molluscs and bryozoans have been studied in four measured and sampled sections located in the northern part of the island. Among these bottom-dwelling organisms, numerous extant taxa are good environmental indicators and, combined with field observations and sedimentological data, they provide information on the probable conditions in which they developed. The siliciclastic deposits of the Kritika Formation have been divided into 14 different bio- and lithofacies, which have been further grouped into four facies associations corresponding to four different environmental settings: (1) continental to fluviatile; (2) brackish-water (lagoonal/deltaic); (3) infralittoral (0–20 m); and (4) upper circalittoral (depths of 20–40 m, but also down to c. 50–60 m). Among the marine facies associations, several characteristic biocoenoses have been recognized: soft-bottoms (fine to coarse sands and gravels); seagrass meadows; biogenic calcareous crusts on drowned beachrock slabs; red algal rhodoliths; and bivalve shell beds. In the studied sections, 13 superimposed genetic sequences have been documented. The repetition of similar facies associations within each sequence suggests: (1) a possibly eustasy-controlled, cyclic sedimentation; (2) a general subsidence of Rhodes during the deposition of the studied facies associations; and (3) a mostly constant range of environmental conditions (i.e. sedimentation rates and temperature) throughout the Gelasian.
ISSN: 0016-7568

hal-01277829
https://hal.archives-ouvertes.fr/hal-01277829
DOI : 10.1017/S0016756815000230

Éditeur(s) : HAL CCSD Springer
Résumé : International audience
Thiswork examines the relevance of the inclusion of ground-based gravity data in the calibration process of a global rainfall-discharge reservoir model. The analysis is performed for the Durzon karst system (Larzac, France). The first part of the study focuses on the hydrological interpretation of the ground-based gravity measurements. The second part of the study investigates further the information content of the gravity data with respect to water storage dynamics modelling.The gravity-derived information is found unable to either reduce equifinality of the single-objective, dischargebased model calibration process or enhance model performance through assimilation.
ISSN: 1866-6280

hal-00812624
https://hal-brgm.archives-ouvertes.fr/hal-00812624
DOI : 10.1007/s12665-012-1856-z

Éditeur(s) : HAL CCSD
Résumé : La grotte d'Angel, datée du Pléistocène moyen et de la base du Pléistocène supérieur, a livré un important matériel lithique et faunistique, et présente un intérêt exceptionnel dans la Péninsule Ibérique. Vu son importance, et dans le cadre d'un programme de recherche européen (N°IDPH/ER/05), une étude pluridisciplinaire a été réalisée sur le remplissage sédimentologique et les vestiges archéologiques. Nous présentons dans cet article les résultats de l'étude des propriétés magnétiques du remplissage de la grot- te. Cette approche a révélé la présence de deux unités magnétostratigraphiques. L'unité stratigraphique inférieure se caractérise par une forte concentration en grains magnétiques, parmi lesquels un fort pour- centage en grains superparamagnétiques (SP). Les minéraux magnétiques sont d'origine secondaire, de petite taille, de nature douce et dominés par la magnétite et la maghémite. Ces derniers ont subi une évo- lution géochimique post-dépositionnelle importante (forte pédogenèse). Au contraire, dans l'unité supé- rieure, les valeurs des différents paramètres magnétiques sont faibles et les minéraux magnétiques sont d'origine détritique et se caractérisent par une force coercitive élevée, conforme à la présence d'hématite. The Angel cave, dated between the middle to the base of the Upper Pleistocene, contains important lithic and faunal material, and is of exceptional interest in the Iberian Peninsula. Because of its importance, and in the framework of an European research project (N°IDPH/ER/05), a multidisciplinary study including palaeomagnetism, was undertaken on the sedimentary deposit and the archaeological material. The study of the magnetic properties of the cave sediments reveals the presence of two magnetostratigraphic units. The lower stratigraphic unit is characterized by an important concentration of magnetic grains with a con- siderable percentage of superparamagnetic grains (SP). The magnetic minerals are of secondary origin, fine grained, magnetically soft and dominated by magnetite and maghemite. The latter have undergone an important post-depositional geochemical evolution (marked pedogenesis). On the contrary, the upper unit is characterized by weaker magnetic parameters and the magnetic minerals are harder, of detrital origin, dominated by hematite
ESTUDIOS GEOLOGICOS-MADRID

hal-00903622
https://hal.archives-ouvertes.fr/hal-00903622
DOI : 10.3989/egeol.40946.222

Éditeur(s) : HAL CCSD Institute for Scientific Computing and Information
Résumé : International audience
The production of oil in soft highly compacted reservoirs produces a significant reduction in the pore space which in turn causes the surface to subside. The authors couple two simulators to model the mechanical deformations in the presence of a Darcy flow, both one- and two-phase. The simulators solve for flow in a porous medium using a finite volume method, and solve for the mechanical deformation of the porous media using a finite element method. The flow equations and the deformation equations are coupled using Biot's law. The authors use two different methods for the coupling: the first uses a staggered algorithm; the second is based on a preconditioned conjugate method. The authors use a multiscale method in both approaches. The authors show that the inf-sup condition is not satisfied, because of the mixed discretization which is done by using two separate simulators. The authors give convergence comparisons for the two methods for several examples. Two of the examples are for the linear problem (one-phase) where they know the exact solution and one is for the nonlinear problem (two-phase). In all cases, the preconditioned conjugate algorithm is faster and more robust, in particular when the inf-sup condition is not satisfied. In the nonlinear problem the authors state that the results agree with physical predictions but do not give actual empirical data. Finally, they show the effects of grid orientation on the nonlinear problem.
ISSN: 1705-5105

hal-00730673
https://hal.archives-ouvertes.fr/hal-00730673

Éditeur(s) : HAL CCSD Wiley
Résumé : Publication Inra prise en compte dans l'analyse bibliométrique des publications scientifiques mondiales sur les Fruits, les Légumes et la Pomme de terre. Période 2000-2012. http://prodinra.inra.fr/record/256699
International audience
Potato can be severely affected by various pathogens, including Pectobacterium atrosepticum, the cause of bacterial soft rot on tubers and of blackleg on stems. To date, no complete resistance to P.similar to atrosepticum is available, so that only cultivars exhibiting partial resistance can be found. The mechanistic basis of this type of resistance is still poorly understood. A proteomic approach was thus developed to identify pathways specifically activated during the interaction between potato tubers and P.similar to atrosepticum. Protein profiles on silver-stained gels in the 58 similar to pH range were obtained from healthy and infected tubers from two cultivars differing for resistance level and analyzed by 2-DE and nano-LC-MS/MS. Thirteen proteins were differentially up-regulated in the partially resistant cv. Kerpondy; by contrast, no significant differences in protein profiles of inoculated and control tubers were observed in the susceptible cv. Bintje. Mass spectrometry and database searching showed that these proteins are involved in energetic metabolism (glyceraldehyde-3-phosphate dehydrogenase, 2-phosphoglycerate dehydratase or enolase, fructose biphosphate aldolase and ATPase a subunit), cytoskeleton structure (actin), protein catabolism (cysteine protease inhibitor) and patatins or patatin precursors. Their involvement in defence responses of cv. Kerpondy to P.similar to atrosepticum is discussed. Proteomic appears as an efficient approach to have insight into the mechanisms and pathways leading to potato resistance against P.similar to atrosepticum.
ISSN: 0931-1785

hal-01208654
https://hal.archives-ouvertes.fr/hal-01208654
PRODINRA : 213002
DOI : 10.1111/j.1439-0434.2012.01950.x

Résumé : L’objet de cette thèse est l’étude des comportements mécanique et à la corrosion d’un nouveau système de fondation, dit pieux SPIRMEC, adapté aux structures légères. Le travail s’est focalisé sur deux grands aspects. Le premier aspect concerne l’analyse du comportement sous chargement axiale des pieux SPIRMEC sur la base de l’expérimentation et de la modélisation numérique dans un sol mou non cohésif. Quant au deuxième aspect, il traite du problème de la corrosion de l’acier constituant le pieu dans un environnement tropical humide. Le comportement des pieux SPIRMEC sous une charge axiale de traction, dans un sol fin non cohésif, a montré le développement d’une surface cylindrique de rupture. Celle-ci ne dépend pas de la configuration géométrique des pieux tel que : l’espacement S, le diamètre d’hélice Dh et le diamètre du tube d. En adoptant ce critère de rupture et à l’aide d’une analyse statistique des données, nous avons proposé quatre méthodes analytiques de prédiction de la capacité portante des pieux SPIRMEC à partir des essais in-situ et au laboratoire qui sont: •Méthode CPT basée sur la résistance de pointe pénétromètrique (essai CPT), •Méthode MPT basée sur la pression limite pressiomètrique (essai MPT), •Méthode du couple d’installation, •Méthode analytique basée sur les paramètres de cisaillement de sol notamment l’angle de frottement interne (essais triaxial et boîte de cisaillement). Ces méthodes tiennent compte de la géométrie du pieu, du procédé de mise en oeuvre et de la compacité du sol. L’analyse de performance des méthodes proposées a montré que les méthodes analytique et CPT représentent mieux le comportement des pieux testés. La modélisation numérique du comportement des pieux SPIRMEC sous charge axiale de traction a été également étudiée à l’aide du code de calcul Plaxis 2D. Un modèle axisymétrique a été adopté pour modéliser la géométrie de la structure. Le modèle de comportement hardening soil a été retenu pour modéliser le comportement élastoplastiq des couches de sol. Un modèle élastique linéaire a été retenu pour le pieu. Quant au comportement de l’interface sol-structure, il a été pris en compte par un modèle élastoplastique basé sur les critères de Mohr-Coulomb. L’expansion du sol résultant de l’installation des pieux a été approchée par une cavité cylindrique. Cette dernière a été modélisée par des déformations volumiques anisotropes. Nous avons constaté, qu’appliquer une déformation volumique de l’ordre de 40% permet une bonne concordance entre les résultats numériques et expérimentaux. L’étude paramétrique nous a également permis de constater l’existence d’une variation linéaire entre la capacité portante et l’espacement S. Le comportement de l’acier galvanisé dans le sol a été également étudié au moyen de trois approches: électrochimique, visuelles grâce au microscope électronique et gravimétrique. Les tests électrochimiques de corrosion du zinc ont été réalisés dans la solution de sol artificielle pour deux périodes bien distinctes : saison des pluies et après 8 mois de contact sol-pieu. Une forte dépendance est constatée de la vitesse de corrosion de zinc au pH et à la conductivité de la solution. La vitesse de corrosion est plus importante en saison des pluies qu’après 8 mois de contact de pieu avec le sol. Les fortes concentrations en sulfates semblent augmenter la vitesse de corrosion. Les analyses menées au MEB montrent que la zone de fluctuation de nappe et en surface externe (sol/air) sont les zones les plus corrodées. La comparaison entre les différentes techniques d’évaluation de la vitesse de corrosion a montré que l’eau de nappe peut être utilisée comme un milieu représentatif du profil chimique d’un sol non cohésif et légèrement granulaire.
The purpose of this thesis is to study the both behaviors mechanical and of the corrosion of a new foundation system, called spirec piles, for lightweight structures. The work was based on two main aspects. The first aspect concerns the analysis of behavior of the spirmec piles under axial loading on the basis of experimental and numerical modeling in a non-cohesive soft soil. On the second aspect, it addresses the problem of corrosion of steel forming the pile in a humid tropical environment. The behavior of the tested piles under axial traction load, in a non-cohesive soil, showed the development of a cylindrical surface of failure. This does not depend on the geometrical configuration of the tested piles such that: the spacing s, the helix diameter dh and the diameter of the shaft. By adopting this failure criterion and using statistical data analysis, we proposed four analytical methods for predicting the bearing capacity of the piles from in-situ and laboratory tests, which are: cpt method based on tip resistance penetrometer (cpt test), mpt method based on pressuremeter limit pressure (test mpt), method of installation torque and analytical method based on the shear parameters of soil (triaxial tests and shear box). These methods take into account the geometry of the pile, the method and implementation of soil compaction. Performance analysis of the proposed methods showed that the analytical methods and cpt represent better the behavior of piles tested. An axisymmetric condition was assumed to model this geometry in two-dimensional space. In this study, we proposed to model the pipe screw pile with plates elements available in plaxis 2d. The helixes were modeled as circular disks. Interface elements were incorporated along the pile to simulate the soil-pile interaction. Hardening soil model was chosen to describe the soil with drained behavior was assigned for all layers. Linear elastic for pile and elastic plastic model based on the mohr-coulomb criterion was used to describe the interface behavior. The lateral expansion generated by the pile shaft was modeled by anisotropic volumetric strains (ɛxx=ɛzz, ɛyy=0). The pile behavior under tensile loading at different volumetric strains, it is clear that the best fit was obtained at volumetric strain of 40%. The parametric study also allowed us to establish the existence of a linear variation between the bearing capacity and spacings. The behavior of the galvanized steel in the ground has also been studied using three approaches such as: electrochemical, microscopic imaging and gravimetrically. Electrochemical tests of the corrosion of the zinc have been made in artificial soil solution into two periods, the rainy season and after eight months of contact soil-pile. Is a strong dependence of the observed corrosion rate of the zinc at the ph and conductivity of the solution. The corrosion rate is higher in the rainy season compared to eight months of contact of the pile with soil. High sulfate concentrations increase the rate of corrosion. The meb analysis shows that the fluctuation zone of the water table is the most corroded area. Comparison between the different methods of evaluating the corrosion rate showed that the ground water may be used as a representative profile of the chemical environment of a non-cohesive soil and slightly granular.

http://www.theses.fr/2014AGUY0790/document

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Torsion experiments (inline image =3 × 10−4 s−1) were performed to investigate the large strain (γmax = 15) rheology on quartz-muscovite aggregate as analogue to pelitic rocks undergoing melting and crystallization during deformation at 300 MPa confining pressure and 750°C temperature. Microstructures reveal four distinct but gradational stages of crystal-melt interactions during deformation--(a) solid state deformation, (b) initiation and domination of partial melting, (c) simultaneous partial melting and crystallization, and (d) domination of crystallization. The microstructural stages are linked to the rheology of the deforming samples. Partial melting starts at relatively low finite shear strains (γ = 1-3) showing approximately 60% strain softening. At γ = 4-10 the partially molten bulk material shows a steady state flow at low stress. Further crystallization of new crystals at the expense of melt between γ = 10 and 15 causes weak strain hardening until the material fails by developing brittle fractures. The stress exponent (n), calculated at γ = 1, 5, and 10, increases from ∼ 3 to ∼ 43, indicating a transition from power to power law breakdown or exponential flow of the bulk system. Hydrostatic experiments for equivalent times and conditions of the torsion experiments were also conducted to evaluate the reaction kinetics and microstructures under static conditions. The new experimental data establish that partially molten rock does not flow according to a constant strain rate-dependent power law (steady state) rheology. The rheological transition from strain rate sensitive to strain rate insensitive flow is interpreted as a function of melt-crystal ratio, their mutual interactions, and the evolution of microstructures in the partially molten rock.
ISSN: 0148-0227

hal-01053709
https://hal.archives-ouvertes.fr/hal-01053709
DOI : 10.1002/2013JB010777

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The lower Pleistocene Kritika Member of the Rhodes Formation is composed of predominantly siliciclastic deposits that are sometimes intercalated with hardbottoms formed by drowning of former beachrock beds. A wide variety of sclerobionts occur in this environment, very different from the poorest soft‐bottom populations occurring in other levels of the Kritika Member. The most characteristic, abundant and frequently diverse are the encrusting forms: coralline algae, bivalves, serpulid worms, and bryozoans. Numerous other groups of sessile and vagile organisms are associated with these crust‐forming communities. A number of skeletal organisms (sometimes including zooxanthellate coral colonies) formed small carbonate buildups on top of several beachrock beds. Boring organisms also occur. Evidence for a two‐step deepening succession over the previously formed beachrock is provided by palaeontological and sedimentological data. The rapidly cemented sandy‐conglomeratic beds were first colonised by a relatively shallow‐water (around 20 m) biocoenosis of mostly encrusting organisms. Another association, with encrusting and erect organisms, was later established in a deeper environment (20-40 m). A comparison with Holocene beachrock occurring on the coast of Rhodes was also undertaken. Their submerged part provided habitat for poorer but similar biotas to those occurring in the Kritika Member. The lower Pleistocene beachrock and associated organogenic fossil assemblages indicate repeated drowning episodes during deposition of the Kritika Member and provide help in sequence stratigraphic interpretations of these siliciclastic deposits. Notably, they can be used as indicators of relative sea‐level changes.
ISSN: 0031-0182

hal-00795591
https://hal.archives-ouvertes.fr/hal-00795591
DOI : 10.1016/j.palaeo.2012.09.007