Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A series of two-stage torsion experiments on Carrara marble were conducted to constrain the influence of known prior deformation on rheological response and microstructural evolution. Comparison with previous experimental data on Carrara marble flow and fabric evolution during single-stage torsion deformation experiments provided direct insights into the significance of initial deformation at various conditions. Our experiments were conducted at 727 degrees C temperature and 300 MPa confining pressure, while maintaining a constant strain rate of 3 x 10(-4) s(-1) on the periphery of the cylindrical samples. Under these conditions, the marble is known to deform in power-law (n = 6-10) ductile flow. All torsion experiments were performed with a Paterson type gas-medium testing machine equipped with a torsion actuator module.;Prior (D1) and subsequent (D2) deformation are accomplished by two torsion experiments in sequence on same sample segments. The effect of D1 strain history is investigated during D2 by applying counter-clockwise torsion to a sandwich sample consisting of three segments with different D1 rotation sense. D2 samples experienced continued, first and reversed shearing deformation in top, centre and bottom segments, respectively. D2 bulk strain was chosen equal to D1 strain in top and bottom segments.;D1 experiments followed the typical single-stage deformation behaviour of Carrara marble under the applied experimental conditions. Yielding was followed by strain hardening until a peak stress was reached at a shear strain around 1, after which work softening occurred. Weakening gradually evolved into a constant stress regime. During hardening, a shear microstructure and crystallographic preferred orientation (CPO) developed. Afterwards the volume fraction of smaller dynamic recrystallised grains increased continuously, resulting in a recrystallisation microstructure and CPO at shear strains of 5 and higher. The new D2 experiments displayed a strain variation between homogeneously deformed sample segments that increased with increasing D1 strain. The stress-strain behaviour of the D2 bulk sandwich samples showed less pronounced work-hardening and -softening when compared with single-stage deformation experiments. Furthermore, constant flow stress was attained at increasingly lower strain with increasing D1 strain. In most D2 segments, fabric development is equivalent to single-stage experiments at corresponding absolute strain. The fabrics differed markedly from those in single-stage experiments in the case of reversed two-stage deformation at moderate strain (D1 shear strain 1 and 2.6). Experiments show that grain shape by shearing of relict grains is defined by finite strain and thus affected by strain reversal. Recrystallisation is controlled by absolute strain and not influenced by strain reversal.
ISSN: 0040-1951

hal-00617686
https://hal.archives-ouvertes.fr/hal-00617686
DOI : 10.1016/j.tecto.2010.09.029

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A Oxford University Press (OUP)
Résumé : International audience
Peridotite xenoliths exhumed by Quaternary alkaline magmatism in the Tahalgha district, southern Hoggar, represent fragments of the subcontinental lithospheric mantle beneath the boundary between the two major structural domains of the Tuareg Shield: the ‘Polycyclic Central Hoggar’ to the east and the ‘Western Hoggar’, or ‘Pharusian Belt’, to the west. Samples were collected from volcanic centres located on both sides of a major lithospheric shear zone at 4°35' separating these two domains. Although showing substantial variations in their deformation microstructures, equilibrium temperatures and modal and chemical compositions, the studied samples do not display any systematic changes of these features across the 4°35' fault. The observed variations rather record small-scale heterogeneities distributed throughout the study area and reflecting the widespread occurrence of vein conduits and metasomatized wall-rocks related to trans-lithospheric melt circulation during the Cenozoic. These features include partial annealing of pre-existing deformation microstructures, post-deformation metasomatic reactions, and trace-element enrichment, coupled with heating from 750–900°C (low-temperature lherzolites) to 900–1150°C (intermediate-T lherzolites and high-T harzburgites and wehrlites). Trace-element modelling confirms that the range of rare earth element (REE) variations observed in the Tahalgha clinopyroxenes may be accounted for by reactive porous flow involving a single stage of basaltic melt infiltration into a light REE (LREE)-depleted protolith. Whole-rock compositions record the final entrapment of disequilibrium metasomatic melts upon thermal relaxation of the veins–wall-rock system. The striking correlations between equilibrium temperatures and trace-element enrichment favor a scenario in which the high-temperature peridotites record advective heat transport along melt conduits, whereas the intermediate- and low-temperature lherzolites reflect conductive heating of the host Mechanical Boundary Layer. This indicates that the lithosphere did not reach thermal equilibrium, suggesting that the inferred heating event was transient and was rapidly erased by thermal relaxation down to the relatively low-temperature present-day geotherm. The low-T (<900°C) deformed lherzolites (porphyroclastic to equigranular) are characterized by only incipient annealing and LREE-depleted clinopyroxene compositions. They were only weakly affected by the Cenozoic events and could represent relatively well-preserved samples from rejuvenated Pan-African lithosphere. Extensive lithospheric rejuvenation occurred either regionally during the Pan-African orogeny, as a result of lithospheric delamination or thermomechanical erosion after thickening, or more locally along the meridional shear zones. The low-T Tahalgha lherzolites are comparable with lherzolites from Etang de Lherz, southern France, interpreted as lithospheric mantle rejuvenated by melt-induced refertilization during a late stage of the Variscan orogeny.
ISSN: 0022-3530

hal-01107410
https://hal.archives-ouvertes.fr/hal-01107410
DOI : 10.1093/petrology/egu056

Éditeur(s) : Université de Bretagne Occidentale
Résumé : The objective of the present work is to study the formation of the passive continental margins of the Central Segment of the South Atlantic, most particularly the Congo and Angola margins. We propose a combined approach, which integrates structural constraints based on geological cross-sections (based on seismic data) and global constraints based on plate kinematic reconstructions. The structural study is based on : i) MCS and refraction data collected during the ZaiAngo programme (a joint project conducted by Ifremer and Total) ; ii) proprietary, industrial seismic data (courtesy of Total) from the Angola margin and iii) on all available seismic lines from the Africa and Brazil conjugated margins, between Walvis Ridge and the Equatorial Fracture Zones. Based on theses data, three structural domains (continental, transitional and oceanic) have been defined, the major characteristics of which are : Crustal thinning occurs abruptly, mostly below the continental slope, over a lateral distance of less than 50 km. The top of the crust deepens as the Moho shallows. Only a few extensional structures are observed ; tilted blocks are very few (one or two, depending on the profile), found only on the upper part of the slope and sealed by a discordance prior to salt deposition. The transitional domain is characterized by the existence of a pre-salt basin lying over a thin crustal layer. No tilted blocks are observed in this domain and reflectors within the pre-salt sediment series are parallel to the base of the Aptian salt, over distances greater than 100 km, precluding the possibility of any significant deformation that would imply large horizontal motions. Two types of crust are observed in the transitional domain. "Type I" crust is found below the undeformed pre-salt sediment series located below the eastern part of the basin ; it is characterized by an upper layer of thickness greater than 5 km and a abnormal velocity layer (7.2 - 7.6 km/s), up to 6 km thick. "Type II" crust is less than 5 km thick and found below the salt compressive front that affects the western part of the basin. The salt cover is continuous (no erosion surface is observed), from the continental shelf to the western termination of the basin. Salt was not deposited in a confined environment (like in the Mediterranean), but in a shallow water, lagunal environment. This imposes the zero-level and constrains the paleo-bathymetry at the time of salt deposition, which dates the latest stage of margin formation. Understanding the formation of a margin cannot be approached without studying the homolog margin. Therefore, it is of major importance to reconstruct the closure of the ocean bordered by these homolog margins and take into account the constraints imposed by the kinematic reconstructions on the lateral motions of the lithospheric plates. In order to assess the relative position of the plates at the ocean closure (prior to crustal thinning), a global study was thus performed, integrating all geophysical and geological constraints, in the ocean and on land. The role of african intra-plate deformation and its limits and their consequences have been thoroughly studied. To juxtapose the margins of the central segment of the Southern Atlantic, it is all the margins bordering the Equatorial Atlantic that need to be adjuste precisely. The kinematic study of this last region shows that the reconstruction obtained are reliable, unambiguous with a quantifiable precision The best fitting poles (obtained using the PLACA software), show that it is impossible to close the margins beyond the superposition of the salt fronts, from the Angola and Brazil margins. The geological cross-sections based on seismic data from the homolog margins indicate that a 330 km wide basin with thin (< 12 km) crust was present at the time of the fit. This basin cannot result from horizontal movement related to pure stretching or simple shear, or any model implying conservative volume. This conclusion is consistent with the existence of presalt reflectors parallel to the salt layer wich extends to the platform: the formation of the pre-salt basin must be related to vertical motions. The scenario that we propose for the evolution of the Congo-Angola margin consist in four stages: the first phase corresponds to extensional deformation limited to the few tilted blocks observed on the upper part of the slope. During the second phase, the main crustal thinning occurs, vertical motions prevailes, resulting in the formation of the continental slope and in the subsidence of the basin. The third phase corresponds to the first stress striction: deformation is concentrated in a limited section of the basin, which corresponds to the salt compression front. A proto-oceanic crust is formed, probably composed of thinned continental crust intruded by mantle material. The second stress striction corresponds to the finale phase, resulting in oceanisation senso stricto. The evolution described shows that we can not apply conservative models for margin formation (such as McKenzie and Wernicke or any of their avatars). In order to explain this thinning, one should investigate non-conservative models (implying geochemical transformation, small scale convection, intrusion...) such as those proposed in marginal or continental basins with no horizontal movments.
Ce travail de thèse aborde la formation des marges continentales passives dans le segment central de l'océan Atlantique Sud (plus particulièrement au Congo et en Angola), en intégrant une étude en coupe (étude structurale à partir des coupes sismiques) et une étude en plan (étude cinématique). L'étude structurale de la marge a été réalisée à partir des données de sismique réflexion et réfraction de la campagne Zaïango et d'une compilation de données sismiques réflexion existantes sur toutes les marges africaine et brésilienne entre les zones de fracture équatoriales et la ride de Walvis. L'interprétation de ces données a permis d'individualiser la structure de la marge en trois domaines : continental, transitionnel et océanique et de déterminer quelques points majeurs sur la structuration de la marge. L'amincissement est abrupt, localisé dans la zone de pente continentale et restreint à 50 km. La marge montre peu de structures distensives : seuls un ou deux blocs basculés sont observés en haut de pente continentale. Le domaine transitionnel est caractérisé par la géométrie particulière de la sédimentation anté-salifère, l'absence de blocs basculés et la faible épaisseur de croûte. La couche sédimentaire anté-salifère montre des réflecteurs plans jusqu'à la base du sel, continus sur 100 km, éliminant toutes possibilités de déformation du socle pendant et après son dépôt. La croûte du domaine transitionnel peut-être divisée en deux types : une croûte de type I sur laquelle se déposent les sédiments non déformés, et une croûte de type II sur laquelle se superposent les limites du « front compressif salifère » bien exprimé dans les séries postsalifères. Enfin le sel, que l'on observe depuis la plate-forme jusqu'au bassin profond, ne se dépose pas dans un bassin confiné (comme en Méditerranée) mais à un niveau proche de 0 m (ressemblant probablement à un dépôt de type lagunaire) et donne la paléo-bathymétrie au moment de son dépôt qui marque la fin de la période de formation de la marge. La compréhension de la genèse d'une marge ne peut être approchée sans son homologue. Cette simple constatation, cette évidence, montre toute l'importance que l'on doit apporter à la reconstruction cinématique initiale de l'océan qui borde ces marges homologues et aux contraintes imposées par les reconstructions cinématiques sur les mouvements horizontaux des plaques lithosphériques. Afin d'étudier la position des marges au moment de cette fermeture, c'est-à-dire avant amincissement, une étude globale intégrant l'ensemble des données disponibles, géophysiques et géologiques, océaniques et continentales, a été réalisée. Le rôle de la déformation intraplaque africaine, ses limites et leurs conséquences a, en particulier, été l'objet d'une attention poussée. Pour juxtaposer les marges du segment central, ce sont toutes les marges de l'océan Atlantique Equatorial qui doivent être ajustées précisément. L'étude cinématique réalisée de la région équatoriale montre que l'on obtient une reconstruction fiable et sans ambiguïté, avec une précision que l'on peut quantifier. Les pôles issus de cette étude (et calculés avec le Logiciel PLACA) indiquent qu'il est impossible d'obtenir une fermeture plus serrée que celle qui conduit à la superposition des fronts salifères brésilien et angolais : les coupes issues de la sismique réflexion des deux marges indiquent qu'il subsiste un bassin aminci, large de plus de 330 km et dont la croûte n'excède jamais 13 kilomètres d'épaisseur. La formation de ce bassin ne peut résulter de mouvements horizontaux, ce qui exclut un amincissement par étirement (pure stretching) ou par l'existence d'une faille de détachement (simple shear) ou par quelque modèle conservatif que ce soit. Cette constatation corrobore l'observation de la présence d'horizons anté-salifère parallèles, entre eux et au sel, couche salifère que l'on retrouve sur la plate-forme : la création de ce bassin anté-salifère ne peut être que liée à un mouvement vertical. Le schéma d'évolution que nous proposons à partir des données structurales et des contraintes cinématiques présente quatre étapes : le premier stade correspond à une phase de déformation distensive limitée aux quelques rares blocs basculés observés en haut de pente continentale. C'est durant la deuxième étape que se déroule la phase d'amincissement principal, les mouvements verticaux prévalent, aboutissant à la formation de la pente continentale et à la subsidence du bassin. La troisième phase correspond à une première striction des contraintes : la déformation se concentre sur une partie réduite du bassin, coïncidant avec le front salifère compressif. Une proto-croûte océanique se forme, probablement composée de croûte continentale amincie et intrudée de matériel mantellique. La seconde striction correspond à la phase finale de formation de la marge et aboutit à l'océanisation sensu stricto. L'étude cinématique et la description de l'évolution de la marge à partir des données sismiques montre donc que l'on ne peut envisager l'application d'un modèle de genèse des marges avec conservation de volume (type McKenzie ou Wernicke et leurs avatars) : pour expliquer l'amincissement du bassin, il faudrait probablement nous intéresser aux modèles non-conservatifs (impliquant transformation, convection à petite échelle, ...) qui sont déjà invoqués pour la formation des bassins marginaux ou continentaux, sans mouvements horizontaux.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2003/these-82.pdf
http://archimer.ifremer.fr/doc/00000/82/

Éditeur(s) : HAL CCSD
Résumé : The present study addresses the question of increasing need in water supply. One line of research consists in investigating karst aquifers that represent significant water supplies for the areas around the Mediterranean. This work aims at developing a methodology of predictive evaluation of karst distribution and karst thickness within the carbonate massifs. It is based on the study of the Tethysian carbonate platform from the area of Montpellier, South of France. This area underwent a polyphased, complex, tectonic evolution, involving successive karst forming events. The approach is based on the relationships between eustacy and geodynamics, on one hand, and base-level variation recorded within palaeokarsts, on the other hand. Sedimentary fill of palaeokarsts allows to identify distinct karstification phases and sometimes to date them. It is a marker of base-level variations, which we attempt to quantify, that is responsible for karst formation and karst filling and sealing. For three palaeokarsts of regional extent, we analyze : karst sedimentary-fill, the distribution along upstream-downstream profile, the vertical extension of palaeokarsts, indicative of the base-level lowering. - The " Bauxite palaeokarst " results from the two-stage evolution of the " Isthme Durancien " : i) Bauxitic weathering of the Neocomian cover over the southern Massif Central , related to an inversion during Barremian ; ii) ≥1600 m uplift and exhumation during Aptian-Albian, inducing erosion of alterites, upstream, and deposition of detrital bauxites, downstream. - The " Early Paleocene palaeokarsts with marine sedimentary-fill " indicate base level variations of more than 350m in the upstream area. It is suggested here that such base-level variations, exceeding eustacy and recorded in tabular undeformed series, result from desiccation-flooding events in an endoreic silled basin. - The " Miocene palaeokarst with Cevennes-sourced sediment-fill " records a Serravalian-Tortonian base-level drop, depicted by canyon incision in the hinterland of the Gulf of Lion Margin. Uplift values of ≥ 400m upstream, about 250m in an intermediate area and 10's of m downstream, are measured. The present 3D geometry and distribution of carbonate massifs (exposed and covered) are modeled in the study area, from the Cevennes to the Mediterranean. The 3D geological model integrates seismic reflection, borehole and gravimetric data. Tectonic restoration of a N-S section, extracted from the 3D model, allows to reconstruct paleo-base-levels with respect with the carbonate massifs, at different stages of deformation and successive phases of karstification. The 3D paleo-flows through carbonates across the study area, are thus constrained, especially during the Messinian desiccation stage. Application of the results to hydrogeology leads to the following : - Uplift of upstream hinterland (Cretaceous, Miocene) produces large amplitude karsts, but they do not make significant reservoirs. - Karstification responsible for the development of important and deep karst reservoirs is related to desiccation of endoreic basins (early Paleocene and Messinian). - Theses two events have produced two main deep karst reservoirs, with a gravimetric signature : (1) Upstream of Montpellier Thrust, between Pic St Loup, Les Matelles Fault and Hérault Basin, a deep karsts developed over 900m thickness in the Malm limestone, during Paleocene. (2) Downstream (south) of Montpellier Thrust, the coastal karsts extend offshore over more than 10km, they are sealed by a thick Miocene to Quaternary cover, and they result from the Messinian event.
Cette étude s'inscrit dans un contexte de demande croissante en ressources en eau, conduisant à mieux contraindre et estimer la distribution des aquifères karstifiés qui représentent une ressource importante, notamment sur le pourtour méditerranéen. Le but de ce travail est d'élaborer une méthode prédictive de la distribution de la karstification et de l'épaisseur de massifs carbonatés karstifiés, notamment pour les karsts profonds. La méthodologie est développée à partir de l'étude des karsts de la plateforme carbonatée téthysienne du Languedoc montpelliérain; région qui a subi une histoire tectonique complexe et polyphasée, entrainant des phases de karstification successives. Elle est basée sur la compréhension des relations entre eustatisme, géodynamique et niveau de base, enregistrées par les paléokarsts de la région. Le remplissage sédimentaire des paléokarsts permet d'identifier les épisodes de karstification et de les dater ; c'est un marqueur des variations -que l'on cherche à quantifier- du niveau de base local responsable de la formation et du comblement des karsts. On analyse 3 paléokarsts d'extension régionale dont on peut étudier : le remplissage karstique, la distribution le long de profils amont-aval et l'extension verticale indicatrice de l'amplitude de l'abaissement du niveau de base dont il est issu. On en déduit les causes géodynamiques à l'origine de leur formation: - Le " paléokarst des bauxites " à remplissage caractéristique, résulte de l'évolution en 2 phases de " l'Isthme Durancien " : altération bauxitique de la couverture néocomienne sur le sud du Massif Central, liée à une inversion au Barrémien, suivi d'une surrection ≥ 1600m à l'Aptien-Albien, causant l'érosion des altérites en amont et le dépôt des bauxites détritiques en aval. - Le " paléokarst à remplissage marin paléocène inférieur " indique des variations du niveau de base local ≥350m dans la zone amont sud-cévenole. On propose que ces variations de niveau de base d'amplitude très supérieures aux variations eustatiques et dans une zone faiblement déformée, résultent d'assèchements et d'ennoiements d'un bassin endoréique à seuil. - Le " paléokarst à remplissage détritique d'origine cévenole ", enregistre la chute du niveau de base au Serravalien-Tortonien, qui se traduit par l'incision de canyons dans l'arrière-pays de la marge du Golfe du Lion. On détermine une surrection de plus de 400 mètres à l'amont, près de 250m dans les blocs faillés intermédiaires et quelques dizaines de mètres dans la zone avale. En parallèle, on établit la géométrie et la distribution actuelles des massifs carbonatés dans la zone d'étude (y compris sous couverture), en construisant un modèle géologique 3D, des Cévennes à la Méditerranée. On intègre les données de sismique réflexion, de forages et les données gravimétriques. La restauration tectonique séquentielle d'une coupe Nord-Sud extraite du modèle géologique permet d'appréhender la position des paléo-niveaux de base par rapport aux massifs carbonatés, pour chaque époque de karstification. On déduit l'organisation 3D des paléo-écoulements à travers la géométrie complexe des massifs carbonatés languedociens, notamment pendant l'évènement messinien. En terme d'évaluation de la ressource en eau, on déduit que: - Les surrections de l'arrière-pays (Crétacé " moyen ", Miocène) produisent des karsts de grande amplitude, mais ne constituent pas de réservoirs significatifs. - La karstification à l'origine de réservoirs exploitables importants et profonds est créée par l'assèchement de bassins endoréiques, qui ont affecté la région au Paléocène inférieur et au Messinien . - Ces deux évènements sont à l'origine de deux principaux réservoirs karstiques profonds qui ont une signature gravimétrique : (1) En amont du chevauchement de Montpellier, entre le Pic Saint Loup, la faille des Matelles et le bassin de l'Hérault, le karst profond se développe sur une épaisseur atteignant 900m, et est attribuée à l'événement du Paléocène. (2) Au Sud du chevauchement de Montpellier les karsts côtiers s'étendent jusqu'à plus de 10 km au large, scellés par une épaisse couverture Miocène et Plio-Quaternaire, et résultent de l'événement Messinien.
https://tel.archives-ouvertes.fr/tel-00936257

tel-00936257
https://tel.archives-ouvertes.fr/tel-00936257
https://tel.archives-ouvertes.fr/tel-00936257/document
https://tel.archives-ouvertes.fr/tel-00936257/file/thA_se_husson_couleurs.pdf

Éditeur(s) : HAL CCSD Geological Society of London
Résumé : International audience
In Eastern China, the North China Block (NCB) has experienced a complex tectonic evolution during Late Palaeozoic to Mesozoic times. The unconformable sedimentary cover, which ranges in age from Neoproterozoic to Permian, underwent two tectonic episodes in Early Triassic and Cretaceous times. An early north–south compressional phase, D1, characterized by north-verging recumbent folds with east–west-trending axes and top-to-the-north ductile shear zones can be observed in a gabbroic pluton and the Neoproterozoic sedimentary host rocks. The available radiometric ages allow us to interpret this event as an Early Triassic back-thrusting related to the final stage of the collision between the North China and South China Blocks. During the LateMesozoic, an extensional event characterized by (1) half-grabens filled by continental terrigeneous red beds and lava flows, (2) low-angle detachment faults, (3) synkinematic granitic plutons, and (4) metamorphic core complexes is widespread in the Eastern Liaoning Peninsula. This extensional D2 event can be subdivided into a ductile deformation and a brittle deformation, corresponding to different expressions of crustal deformation. In every area studied in the Eastern Liaoning Peninsula, the ductile D2 deformation is characterized by a NW–SE-trending stretching lineation with a top-to-the-NWsense of shear.Mica and amphibole fromthe metamorphic country rocks, granodioritic or monzogranitic plutons and their mylonitized margins yield 40Ar/39Ar ages ranging from 130 to 120 Ma. These dates support fast cooling and exhumation rates coeval with the extensional tectonics. The brittle D2 deformation is responsible for the formation of high-angle normal faults marked by low-temperature cataclasites bounding half-grabens. During the Mesozoic, the tectonic regime of Eastern China experienced a significant inversion from compression to extension. The Eastern Liaoning Peninsula massif provides an example of this geodynamic transition.
ISSN: 2041-4927

hal-00134055
https://hal-insu.archives-ouvertes.fr/hal-00134055
DOI : 10.1144/SP280.7

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Rifting in a cratonic lithosphere is strongly controlled by several interacting processes including crust/mantle rheology, magmatism, inherited structure and stress regime. In order to better understand how these physical parameters interact, a 2 yr long seismological experiment has been carried out in the North Tanzanian Divergence (NTD), at the southern tip of the eastern magmatic branch of the East African rift, where the southward-propagating continental rift is at its earliest stage. We analyse teleseismic data from 38 broad-band stations ca. 25 km spaced and present here results from their receiver function (RF) analysis. The crustal thickness and Vp/Vs ratio are retrieved over a ca. 200 × 200 km2 area encompassing the South Kenya magmatic rift, the NTD and the Ngorongoro-Kilimanjaro transverse volcanic chain. Cratonic nature of the lithosphere is clearly evinced through thick (up to ca. 40 km) homogeneous crust beneath the rift shoulders. Where rifting is present, Moho rises up to 27 km depth and the crust is strongly layered with clear velocity contrasts in the RF signal. The Vp/Vs ratio reaches its highest values (ca. 1.9) beneath volcanic edifices location and thinner crust, advocating for melting within the crust. We also clearly identify two major low-velocity zones (LVZs) within the NTD, one in the lower crust and the second in the upper part of the mantle. The first one starts at 15–18 km depth and correlates well with recent tomographic models. This LVZ does not always coexist with high Vp/Vs ratio, pleading for a supplementary source of velocity decrease, such as temperature or composition. At a greater depth of ca. 60 km, a mid-lithospheric discontinuity roughly mimics the step-like and symmetrically outward-dipping geometry of the Moho but with a more slanting direction (NE–SW) compared to the NS rift. By comparison with synthetic RF, we estimate the associated velocity reduction to be 8–9 per cent. We relate this interface to melt ponding, possibly favouring here deformation process such as grain-boundary sliding (EAGBS) due to lithospheric strain. Its geometry might have been controlled by inherited lithospheric fabrics and heterogeneous upper mantle structure. We evidence that crustal and mantle magmatic processes represent first order mechanisms to ease and locate the deformation during the first stage of a cratonic lithospheric breakup.
ISSN: 0956-540X

hal-01622078
https://hal.archives-ouvertes.fr/hal-01622078
https://hal.archives-ouvertes.fr/hal-01622078/document
https://hal.archives-ouvertes.fr/hal-01622078/file/plasmanGJI2017.pdf
DOI : 10.1093/gji/ggx177

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In orogenic systems, thrust faults play a major role in stacking different tectonic units and may act as conduits for the expulsion of large amounts of fluid of different origins (metamorphic, diagenetic, meteoric). This study focuses on the Monte Perdido thrust unit emplaced in the Paleogene Jaca thrust-sheet-top basin, in the SW-central Pyrenees. We aim to decipher the mechanisms and P-T conditions of deformation in fault zones and characterize the related fluid involvement, through combined microstructural, geochemical and microthermometry analyses. Two thrust faults cutting platform limestones, marls and siliciclastic turbidites of the lower part of the basin-fill (Paleocene-lower Eocene) have been studied. The fault zones are characterized by metre-thick shear zones with highly deformed, foliated clay-rich sediments. Foliation is underlined by preferentially oriented phyllosilicates. Several generations of shear and extension calcite, quartz and chlorite-bearing veins attest to fluid-rock interactions during a multi-stage deformation. Microstructural observations and stable isotope analyses on calcite from veins and host sediments suggest that deformation was aseismic and dominated by diffusive mass transfer from pressure solution sites along cleavage and stylolites to the precipitation sites in veins, with mineralizing fluids in equilibrium with the host sediments. Our results suggest an essentially closed hydrologic system, and imply the absence of significant fluid flow along the studied fault zones. Microthermometric study on fluid inclusions present in calcite and quartz veins, and calcite-quartz oxygen isotopic fractionation determined for the first generation shear veins, allow a geothermal gradient of 34 degrees C/km to be estimated. Analytical results demonstrate an evolution of the fault zones in three stages. The first stage was related to the emplacement of the Monte Perdido thrust unit during the middle Eocene at a temperature of similar to 208 degrees C and a burial depth of similar to 5.7 km. The second stage corresponds to a fault reactivation at a temperature of similar to 240 degrees C and a burial depth of similar to 6.5 km. The latter deformation may have been related to folding of the Monte Perdido thrust unit during the emplacement of the underlying Gavarnie thrust unit during the late Eocene-early Oligocene, with deeper burial resulting from aggradation of the thrust-sheet-top basin-fill. The last event corresponds to the formation of a dilatant vein system likely related to the exhumation of the massif.
ISSN: 0191-8141

hal-00644828
https://hal.archives-ouvertes.fr/hal-00644828
DOI : 10.1016/j.jsg.2011.06.006

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Convergent plate margins typically experience a transition from subduction to collision dynamics as massive continental blocks enter the subduction channel. Studies of high-pressure rocks indicate that tectonic fragments are rapidly exhumed from eclogite facies to mid-crustal levels, but the details of such dynamics are controversial. To understand the dynamics of a subduction channel we report the results of a petrochronological study from the central Sesia Zone, a key element of the internal Western Alps. This comprises two polymetamorphic basement complexes (Eclogitic Micaschist Complex and Gneiss Minuti Complex) and a thin, dismembered cover sequence (Scalaro Unit) associated with pre-Alpine metagabbros and metasediments (Bonze Unit). Structurally controlled samples from three of these units (Eclogitic Micaschist Complex and Scalaro-Bonze Units) yield unequivocal petrological and geochronological evidence of two distinct high-pressure stages. Ages (U-Th-Pb) of growth zones in accessory allanite and zircon, combined with inclusion and textural relationships, can be tied to the multi-stage evolution of single samples. Two independent tectono-metamorphic 'slices' showing a coherent metamorphic evolution during a given time interval have been recognized: the Fondo slice (which includes Scalaro and Bonze rocks) and the Druer slice (belonging to the Eclogitic Micaschist Complex). The new data indicate separate stages of deformation at eclogite-facies conditions for each recognized independent kilometer-sized tectono-metamorphic slice, between ∼85 and 60 Ma, with evidence of intermittent decompression (ΔP ∼ 0*5 GPa) within only the Fondo slice. The evolution path of the Druer slice indicates a different P-T-time evolution with prolonged eclogite-facies metamorphism between ∼85 and 75 Ma. Our approach, combining structural, petrological and geochronological techniques, yields field-based constraints on the duration and rates of dynamics within a subduction channel.
ISSN: 0022-3530

hal-01054335
https://hal.archives-ouvertes.fr/hal-01054335
DOI : 10.1093/petrology/egu029

Éditeur(s) : HAL CCSD Elsevier
Résumé : We have studied the phase transformation of forsterite to wadsleyite under shear stress at the Earth's transition zone pressure and temperature conditions. Two-step experiments were performed using a multi-anvil press. First, we hot pressed iron-free forsterite at 6 or 11 GPa and 1100 degrees C. Then we deformed a slab of this starting material using a direct simple shear assembly at 16 GPa and 1400 degrees C for 1, 15, 35, 40, or 60 min. Both the starting material and the deformed samples were characterized using optical and scanning electron microscopy including measurements of crystal preferred orientations (CPO) by electron back scattered diffraction (EBSD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FTIR). The phase transformation occurs very rapidly, in less than 1 min, and metastable forsterite relics are not observed after deformation. The grain size of wadsleyite is slightly smaller than the forsterite starting material. The water contents obtained from FTIR analyses in forsterite and wadsleyite are 65-124 wt ppm H2O and 114-736 wt ppm H2O, respectively, which are well below water solubility at similar conditions in the presence of free water. Wadsleyite aggregates display weak CPO patterns with [1 0 0] axes concentrated at low angle to the shear direction, [0 1 0] axes perpendicular to the shear plane and nearly random [0 0 1] axes. Only a few dislocations were observed in wadsleyite with TEM. This observation is consistent with the assumption that most dislocations formed during the initial high-stress stages of these stress-relaxation experiments, were consumed in the phase transformation, probably enhancing the transformation rate. CPO patterns vary as a function of the water content: with increasing water content the density of [1 0 0] axes parallel to the shear direction decreases, and the density of [0 0 1] axes increases. Viscoplastic self-consistent modeling of CPO evolution using previously reported glide systems for wadsleyite, i.e., [1 0 0]{0 k 1} and 1/2 (1 1 1){1 0 1}, cannot reproduce the measured CPO, unless the [0 0 1](0 1 0) system, for which dislocations have not been observed by TEM, is also activated. In addition, wadsleyite grain growth suggests the participation of diffusion-assisted processes in deformation. Calculated anisotropies for P and S-waves using measured CPO are always below 1%. This very low anisotropy is due to both the low finite strain achieved in the experiments, which leads to weak wadsleyite CPO, and to the diluting effect of added majorite. The present experiments emphasize the importance of stress, grain size evolution and water content in the forsterite to wadsleyite phase transformation and subsequent deformation in the transition zone.
ISSN: 0031-9201

hal-00617430
https://hal.archives-ouvertes.fr/hal-00617430
DOI : 10.1016/j.pepi.2010.11.001

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The ENE-WSW Autun Shear Zone in the northeastern part of the French Massif Central has been interpreted previously as a dextral wrench fault. New field observations and microstructural analyses document a NE-SW stretching lineation that indicates normal dextral motions along this shear zone. Further east, similar structures are observed along the La Serre Shear Zone. In both areas, a strain gradient from leucogranites with a weak preferred orientation to highly sheared mylonites supports a continuous Autun-La Serre fault system. Microstructural observations, and shape and lattice-preferred orientation document high-temperature deformation and magmatic fabrics in the Autun and La Serre granites, whereas low- to intermediate-temperature fabrics characterize the mylonitic granite. Electron microprobe monazite geochronology of the Autun and La Serre granites yields a ca. 320 Ma age for pluton emplacement, while mica 40Ar-39Ar datings of the Autun granite yield plateau ages from 305 to 300 Ma. The ca. 300 Ma 40Ar-39Ar ages, obtained on micas from Autun and La Serre mylonites, indicate the time of the mylonitization. The ca. 15-Ma time gap between pluton emplacement and deformation along the Autun-La Serre fault system argue against a synkinematic pluton emplacement during late orogenic to postorogenic extension of the Variscan Belt. A ductile to brittle continuum of deformation is observed along the shear zone, with Lower Permian brittle faults controlling the development of sedimentary basins. These results suggest a two-stage Late Carboniferous extension in the northeastern French Massif Central, with regional crustal melting and emplacement of the Autun and La Serre leucogranites around 320 Ma, followed, at 305-295 Ma, by ductile shearing, normal brittle faulting, and subsequent exhumation along the Autun-La Serre transtensional fault system.
ISSN: 1437-3254

insu-00596918
https://hal-insu.archives-ouvertes.fr/insu-00596918
https://hal-insu.archives-ouvertes.fr/insu-00596918/document
https://hal-insu.archives-ouvertes.fr/insu-00596918/file/Article_Morvan_v_INIST.pdf
DOI : 10.1007/s00531-011-0673-z

Éditeur(s) : HAL CCSD Elsevier
Résumé : In order to address the question of the processes involved during shear zone nucleation, we present a petro-structural analysis of millimetre-scale shear zones within the Roffna rhyolite (Suretta nappe, Eastern central Alps). Field and microscopic evidences show that ductile deformation is localized along discrete fractures that represent the initial stage of shear zone nucleation. During incipient brittle deformation, a syn-kinematic metamorphic assemblage of white mica + biotite + epidote + quartz precipitated at ca. 8.5 ± 1 kbar and 480 ± 50 °C that represent the metamorphic peak conditions of the nappe stacking in the continental accretionary wedge during Tertiary Alpine subduction. The brittle to ductile transition is characterized by the formation of two types of small quartz grains. The Qtz-IIa type is produced by sub-grain rotation. The Qtz-IIb type has a distinct CPO such that the orientation of c-axis is perpendicular to the shear fracture and basal and rhombhoedric slip systems are activated. These Qtz-IIb grains can either be formed by recrystallization of Qtz-IIa or by precipitation from a fluid phase. The shear zone widening stage is characterized by a switch to diffusion creep and grain boundary sliding deformation mechanisms. During the progressive evolution from brittle nucleation to ductile widening of the shear zone, fluid–rock interactions play a critical role, through chemical mass-transfer, metasomatic reactions and switch in deformation mechanisms.
ISSN: 0191-8141

hal-01355954
https://hal.archives-ouvertes.fr/hal-01355954
DOI : 10.1016/j.jsg.2016.02.015

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Alkali feldspar thermochronologic modeling with the 40Ar/39Ar method has generated marked advances in knowledge of the mechanisms for argon diffusion in feldspars. While the goal in many cases has been to extrapolate the observed and modeled argon behavior in feldspars to natural geological settings, scientific debate surrounding the true feasibility of such extrapolations and indeed, the validity of thermochronologic modeling in itself, have provided much impetus to improve laboratory techniques to test, and increase basic understanding of, argon diffusion. Two cornerstones for the debate over the feasibility of alkali feldspar thermochronology for modeling natural, geologic processes have been: 1. is volume diffusion the main mechanism for argon movement in feldspars? and 2. if volume diffusion is a viable mechanism, does argon then reside in discrete ‘domains' within the feldspar lattice? We describe a study of alkali feldspars from a profile through a well-controlled brittle fault zone in western Norway; the feldspars document argon loss during deformation and strongly suggest the existence of argon ‘domains' within the feldspars, at least during laboratory step heating. The progressive change in the character of argon diffusion is recognizable in the logr/ro diffusion data from the feldspars and is mimicked by physical changes observed optically in the feldspars through progressive degrees of brittle deformation. Modeling results indicate a reduction in size of the biggest domains and the appearance of smaller domains during the strongest stages of deformation. Whether or not this reveals the existence and the transformation of the domain structure in naturo is difficult to prove from our data alone, but interestingly, this behaviour corresponds directly to the physical (optical) appearance of more intense crack networks and subgrains in progressively more brecciated feldspars. Because the thermochronologic histories derived from modeling the feldspar data conform very well to the known tectonic history of the area, the feldspars appear to have successfully retained physical (optical and isotopic) records of episodic tectonic processes operating from ductile through lowtemperature brittle regimes in rocks with a Caledonian history overprinted by several later (younger) geologic events. However, because the ‘cold' brecciation is the last tectonothermal event recorded by these rocks, it is impossible to truly test for the existence of diffusion domains in naturo. Argon loss appears to have been effective only in the most highly brecciated (deformed) samples where the combination of the connected crack network, increased fluid flow and higher temperatures enhanced diffusion via fast diffusion pathways and thus, volume diffusion from the lattice. Only minor argon loss occurred in zones of lower brittle strain, although some development of cracks and brittle features is evident. Independent of the existence of diffusion domains, this study highlights the possible pitfalls when cooling histories are deduced from brecciated feldspars in which age and diffusion charateristics have been decoupled: while the geochronological memory has survived and is identical to that of nonbrecciated feldspars (suggesting no loss and minor effects of deformation), the diffusion characteristics have been completely transposed by brecciation and the appearance of new domains. Modeling feldspars with these latter characteristics would effectively utilise a new feldspar diffusion structure with an ‘old' (relict) age memory.
ISSN: 0016-7037

hal-00198283
https://hal.archives-ouvertes.fr/hal-00198283
https://hal.archives-ouvertes.fr/hal-00198283/document
https://hal.archives-ouvertes.fr/hal-00198283/file/KsparBreccia_Arnaud_Eide_GCA_2000.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Aegean domain is a key area for understanding the processes of back-arc extension. Observed deformation pattern and present day kinematics result from the interaction between the southward retreat of the Hellenic trench and the westward escape of Anatolia. Lithosphere-scale analogue models were employed to display that the overall pattern of Aegean extension requires not only the combination of trench retreat and Anatolia escape since middle Miocene but also the presence of an inherited lithosphere-scale mechanical discontinuity: the Vardar Suture Zone (VSZ). The reactivation in dextral shear of the eastern branch of the VSZ accommodates both the trench retreat (NS stretching) and the westward escape of Anatolia (EW shortening) in the Cyclades area since middle Miocene. Additionally, our model shows that the North Anatolian Fault (NAF) is a late structure in the evolution of the Aegean, initiated around 10 Ma after the onset of Anatolia escape. The displacement field at the surface of the model allows the identification of sub-domains, which result from strain partitioning instead of being "rigid microplates", directly comparable to the present-day displacement field (GPS) of the Aegean and western Anatolia. Our model provides a simple but powerful way to look at the dynamics of Aegean extension in two main stages. From middle Eocene to middle Miocene, extension was only driven by the southward retreat of the Hellenic trench at a rate lower than 1 cm*y− 1. Since middle Miocene, the combination of slab rollback with Anatolia westward escape resulted in a southwest direction of trench retreat, with an accelerating rate of up to 3 cm*y− 1.
ISSN: 0040-1951

insu-01066042
https://hal-insu.archives-ouvertes.fr/insu-01066042
https://hal-insu.archives-ouvertes.fr/insu-01066042/document
https://hal-insu.archives-ouvertes.fr/insu-01066042/file/Philippon-brun-tect-2014-HAL.pdf
DOI : 10.1016/j.tecto.2014.04.039

Éditeur(s) : HAL CCSD
Résumé : This thesis is devoted to the study of the geodynamic evolution of the panafrican belt in NW Angola, lying on the western margin of the Congo craton. This orogenic belt, resulting from the late neoproterozoic - early paleozoic convergence of the São Francisco and Congo cratons, can be subdivided into two main domains: 1) an eastern foreland made of folded neoproterozoic sediments and 2) a western hinterland made of magmatic and metamorphic rocks. Our structural, petrological, geochemical and geochronological studies lead to the recognition of two main units within this hinterland : 1) an upper eastern unit made of gneiss and micaschists (PTmax : 8-12 kbar, 650-680°C) that preserves D1 deformation structures related to the ENE transport of nappes and 2) a western lower unit made of gneiss and migmatites (P-Tmax : 7-9 kbar, 700-750°C) that were affected by a polyphased deformation. Our geochronological study shows that this belt contains ~2Ga old granites that were involved in a polyphased panafrican evolution between 540 Ma for syn-D1 peak metamorphic conditions and 480 Ma for the last stages of recrystallization and exhumation of high grade rocks. The synthesis of all data leads to a precise reconstruction of P-T-D-t paths in both tectonometamorphic units and to comparison of this panafrican belt with similar belts distributed on both sides of the Atlantic ocean. This work attests of the complexity of the geodynamic processes resulting in the Gondwana assembly and implying both large cratonic landmasses and intercalated microplates.
Cette thèse est consacrée à l'étude de l'évolution géodynamique de la chaîne panafricaine au NW de l'Angola, sur la marge occidentale du craton du Congo. Ce segment orogénique, conséquence de la convergence des cratons du São Francisco et du Congo à la fin du Néoprotérozoïque et début du Paléozoïque, peut être subdivisé en un domaine externe plissé et peu métamorphique et un domaine interne formé de roches magmatiques et métamorphiques. Les études structurales, pétrologiques, géochimiques et géochronologiques conduisent à distinguer deux unités principales dans le domaine interne : - l'unité supérieure de gneiss et micaschistes (P-Tmax : 8-12 kbar, 650-680°C) dont la déformation D1 est synchrone de la mise en place des nappes vers l'ENE; - l'unité inférieure dans la partie occidentale constituée de gneiss et migmatites (P-Tmax : 7-9 kbar, 700-750°C) affectés par une déformation polyphasée. L'étude géochronologique démontre l'existence de protolithes granitiques datés à ~2 Ga impliqués dans l'orogénèse pan africaine caractérisée par une histoire polyphasée entre 540 Ma pour le pic du métamorphisme syn-D1 et 480 Ma pour les dernières phases de recristallisation et d'exhumation des roches métamorphiques de haut grade. La synthèse des données permet ainsi de reconstruire précisément les deux chemins P-T-D-t de ces deux unités tectono-métamorphiques et de comparer ce segment panafricain à ceux présents de part et d'autre de l'Atlantique Sud. Ce travail témoigne de la complexité des processus géodynamiques de convergence amenant à l'assemblage du Gondwana impliquant à la fois de larges masses cratoniques et des microplaques intercalées entre ces masses.
https://tel.archives-ouvertes.fr/tel-00770757

Droits : info:eu-repo/semantics/OpenAccess
tel-00770757
https://tel.archives-ouvertes.fr/tel-00770757
https://tel.archives-ouvertes.fr/tel-00770757/document
https://tel.archives-ouvertes.fr/tel-00770757/file/these2012-Nsungani.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
Aegean extension is a process driven by slab rollback that since 45 Ma shows a two-stage evolution. From 45 to13 Ma it is accommodated by localized deformation leading to i) the exhumation of high-pressure metamorphicrocks from mantle to crustal depths, ii) the exhumation of high-temperature rocks in core complexes and iii) thedeposition of Paleogene sedimentary basins. Since 13 Ma, extension is distributed over the whole Aegean domaingiving a widespread development of onshore and offshore Neogene sedimentary basins. The 3D reconstruction atAegean scale of this two-stage evolution shows that the rate of trench retreat was around 0.6 cm/y during the first30 My and then accelerated up to 3.2 cm/y during the last 13 My. Using available tomographic evidence, timingof metamorphic and sedimentary processes, paleomagnetic data and geometry and kinematics of deformation, wepropose that the sharp transition in trench retreat and deformation mode, localized vs distributed, at 13 Ma wascontrolled to slab tearing. Moreover, the development of dextral NE-SW strike-slip faults and related pull-apartbasins in the North Aegean domain, from the Cyclades to the Rhodope, strongly suggests that this sharp transitionalso corresponds to the onset of Anatolia westward escape.
Geophysical Research Abstracts
Vienne, Austria

insu-01137631
https://hal-insu.archives-ouvertes.fr/insu-01137631

Éditeur(s) : HAL CCSD
Résumé : International audience
Aegean extension is a process driven by slab rollback that, since 45 Ma, shows a twostage evolution. From Middle Eocene to Middle Miocene it is accommodated by localized deformation leading to i) the exhumation of high-pressure metamorphic rocks from mantle to crustal depths, ii) the exhumation of high-temperature rocks in core complexes and iii) the deposition of Paleogene sedimentary basins. Since Middle Miocene, extension is distributed over the whole Aegean domain giving a widespread development of onshore and offshore Neogene sedimentary basins. We reconstructed this two-stage evolution in 3D at Aegean scale by using available ages of metamorphic and sedimentary processes, geometry and kinematics of ductile deformation, paleomagnetic data and available tomographic models. The restorationmodel shows that the rate of trench retreat was around 0.6 cm/y during the first 30 My and then accelerated up to 3.2 cm/y during the last 15 My. The sharp transition observed in the mode of extension, localized versus distributed, which occurred in Middle Miocene correlates with the acceleration of trench retreat and is more likely a consequence of the Hellenic slab tearing documented by mantle tomography. The development of large dextral NE-SW strike-slip faults during the second stage of Aegean extension, since Middle Miocene, is illustrated by the 450 Km-long fault, recently put in evidence, offshore from Myrthes to Ikaria and onshore from Izmir to Balikeshir, in western Anatolia. Therefore, the interaction between the Hellenic trench retreat and the westward displacement of Anatolia started in Middle Miocene,almost 10 Ma before the propagation of the North Anatolian Fault in the North Aegean. This raises a fundamental issue concerning the dynamic relationship between slab tearing and Anatolia displacement
ISSN: 0438-9557

insu-01574659
https://hal-insu.archives-ouvertes.fr/insu-01574659
https://hal-insu.archives-ouvertes.fr/insu-01574659/document
https://hal-insu.archives-ouvertes.fr/insu-01574659/file/EFFECTS_OF_SLAB_ROLLBACK_ACCELERATION_ON_AEGEAN_EX.pdf
DOI : 10.12681/bgsg.11697

Éditeur(s) : HAL CCSD National Research Council Canada
Résumé : International audience
Back-arc extension in the Aegean, which was driven by slab rollback since 45 Ma, is described here for the first time in two stages. From Middle Eocene to Middle Miocene, deformation was localized leading to i) the exhumation of high-pressure metamorphic rocks to crustal depths, ii) the exhumation of high-temperature metamorphic rocks in core complexes and iii) the deposition of sedimentary basins. Since Middle Miocene, extension distributed over the whole Aegean domain controlled the deposition of onshore and offshore Neogene sedimentary basins. We reconstructed this two-stage evolution in 3D and four steps at Aegean scale by using available ages of metamorphic and sedimentary processes, geometry and kinematics of ductile deformation, paleomagnetic data and available tomographic models. The restoration model shows that the rate of trench retreat was around 0.6 cm/y during the first 30 My and then accelerated up to 3.2 cm/y during the last 15 My. The sharp transition observed in the mode of extension, localized versus distributed, in Middle Miocene correlates with the acceleration of trench retreat and is likely a consequence of the Hellenic slab tearing documented by mantle tomography. The development of large dextral NE-SW strike-slip faults, since Middle Miocene, is illustrated by the 450 Km-long fault zone, offshore from Myrthes to Ikaria and onshore from Izmir to Balikeshir, in western Anatolia. Therefore, the interaction between the Hellenic trench retreat and the westward displacement of Anatolia started in Middle Miocene, almost 10 Ma before the propagation of the North Anatolian Fault in the North Aegean.
ISSN: 0008-4077

insu-01271296
https://hal-insu.archives-ouvertes.fr/insu-01271296
https://hal-insu.archives-ouvertes.fr/insu-01271296/document
https://hal-insu.archives-ouvertes.fr/insu-01271296/file/Brun%20etal%20CJES%202016.pdf
DOI : 10.1139/cjes-2015-0203

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In East Asia, widespread extensional sedimentary basins together with the close association of Metamorphic Core Complexes and magmatism are prominent features of the large-scale wide rift system developed during late Mesozoic times. This region thus appears as a proper place to study continental extension as well as questions about the link between continental extension and magmatism. This paper primarily provides pioneer exhumation time-constraints on the Linglong MCC (Jiaodong Peninsula) including cooling and deformation ages. MCC cooling at mid-crustal levels occurred at ca. 143 Ma. Besides, last ductile deformation occurred at ca. 134 Ma while final exhumation stages, under brittle 2 conditions, occurred as late as ca. 128 Ma. Continuous crustal stretching were then recorded by the emplacement of a synkinematic pluton in the upper crust at ca. 128 Ma that cooled fast below an intracrustal shear zone crossing the ductile-brittle transition at ca. 123 Ma. The ca. 120-118 Ma age cluster is ascribed to the fast cooling of undeformed plutons marking the end of extension that lasted, in the area, over a minimum period of ca. 30 My. Combining other MCC exhumation constraints and the onset of subsidence in the sedimentary basins, total duration of late Mesozoic extension in East Asia could be estimated at ca. 60 My, related with a rather long process for extension from 160 to at least 100 Ma. East Asian continental extension is heterogeneously distributed in space and time as revealed by fundamental differences between two end-member classes of migmatite-cored MCC already described in other wide rift systems. Extension seems to have first favoured partial melting which subsequently, in turn, maintained continental extension.
ISSN: 1342-937X

insu-00752551
https://hal-insu.archives-ouvertes.fr/insu-00752551
https://hal-insu.archives-ouvertes.fr/insu-00752551/document
https://hal-insu.archives-ouvertes.fr/insu-00752551/file/Charles_et_al_Gondwana_Research_2012.pdf
DOI : 10.1016/j.gr.2012.10.011

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Mediterranean geodynamic system is an exceptional natural laboratory to study the complexities of back-arc extension during subduction rollback. Corsica is a key locality that recorded the Alpine subduction-collision history followed by 30 Ma of the Apennines slab rollback, responsible for the successive opening, from West to East, of the Liguro-Provençal basin and the Tyrrhenian Sea. The overall strain pattern of the Alpine metamorphic units of Alpine Corsica is studied through a synthesis of i) available geological maps, ii) geochronological data and iii) newly acquired structural data relative to successive events of ductile and brittle extension, Three main stages of extension are recorded: 1/ Syn-metamorphic Oligocene extension accommodated by N140° trending ductile shear zones, that correspond to the reactivation of a major Alpine thrust; 2/ Burdigalian ramp-flat extension with N60°-70° trending fault zones that controlled the deposition of onshore piggy-back basins (e.g. St Florent basin), and 3/ Serravalian N-S trending fault zones. From a geodynamical point of view, these successive extensional deformations in Alpine Corsica can be correlated to the history of the Apennines slab rollback. The two first stages are related to a southeastward rollback of the Appennines slab that successively triggered: 1/ Continental rifting in Oligocene leading to the opening of the Liguro-Provençal basin and 2/ Burdigalian extension with N60°-70° trending fault zone, oblique to the Alpine thrust that, after a counterclockwise rotation of the Corso-Sardinian block, became unable to accommodate extension. Finally, the third stage that gave NS-trending fault zones developed in Serravalian, at the onset of Tyrrhenian rifting, related to an eastward rollback of the Apennines slab, as a response of slab tearing in Sicily.
ISSN: 0040-1951

insu-01424859
https://hal-insu.archives-ouvertes.fr/insu-01424859
https://hal-insu.archives-ouvertes.fr/insu-01424859/document
https://hal-insu.archives-ouvertes.fr/insu-01424859/file/gueydan-tectonoph-2017.pdf
DOI : 10.1016/j.tecto.2016.12.028

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Seismic anisotropy of the south Iberian upper mantle is investigated using shear-wave splitting of SKS phases. We analyzed teleseismic events recorded by sixteen permanent broadband stations installed on the southern Iberian Peninsula and in northern Africa, and we determined fast polarization directions phi, and delay times delta t between fast and slow components. The area of investigation extends across two important geological structures in the Variscan Iberian Peninsula: the Variscan Iberian Massif in its center, and the Gibraltar arc in the Southeast, that represents the most westerly Alpine belt in the western Mediterranean. Shear-wave splitting measurements from stations in the Betic domain show homogeneous ENE-WSW fast directions nearly parallel to the trend of the mountain belt, and smooth spatial variations. Stations in the North, toward the southern part of the Variscan Iberian Massif show homogeneous fast directions however trending NS to NE-SW, different from those recorded in the Betic. These observations may reflect a post-Hercynian (Variscan) deformation of the Ossa-Morena zone, related to the main stages in the tectonic evolution of this part, namely transpressional stage, transtensional stage and shortening episode, or a deformation related to the posterior Alpine orogeny. Along the Gibraltar arc, we observe a smoothly varying phi trend changing from ENE-WSW in the Eastern Betics to NS in the area of Gibraltar and Ceuta, following more or less the general trend of the mountain belt around the Alboran Sea, and the coastline. Since a similar rotation is also visible in results from Pn anisotropy, this suggests that the anisotropy is vertically coherent starting from just below the Moho. Comparing the anisotropy pattern expected from various geodynamic models with the observed SKS splitting suggests that the anisotropy is best explained by a model of slab rollback, rather than by delamination models.
ISSN: 0012-821X

hal-00412175
https://hal.archives-ouvertes.fr/hal-00412175
https://hal.archives-ouvertes.fr/hal-00412175/document
https://hal.archives-ouvertes.fr/hal-00412175/file/Buontempo_SKS_gibraltar_EPSL2008_hal.pdf
DOI : 10.1016/j.epsl.2008.06.024