Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A series of two-stage torsion experiments on Carrara marble were conducted to constrain the influence of known prior deformation on rheological response and microstructural evolution. Comparison with previous experimental data on Carrara marble flow and fabric evolution during single-stage torsion deformation experiments provided direct insights into the significance of initial deformation at various conditions. Our experiments were conducted at 727 degrees C temperature and 300 MPa confining pressure, while maintaining a constant strain rate of 3 x 10(-4) s(-1) on the periphery of the cylindrical samples. Under these conditions, the marble is known to deform in power-law (n = 6-10) ductile flow. All torsion experiments were performed with a Paterson type gas-medium testing machine equipped with a torsion actuator module.;Prior (D1) and subsequent (D2) deformation are accomplished by two torsion experiments in sequence on same sample segments. The effect of D1 strain history is investigated during D2 by applying counter-clockwise torsion to a sandwich sample consisting of three segments with different D1 rotation sense. D2 samples experienced continued, first and reversed shearing deformation in top, centre and bottom segments, respectively. D2 bulk strain was chosen equal to D1 strain in top and bottom segments.;D1 experiments followed the typical single-stage deformation behaviour of Carrara marble under the applied experimental conditions. Yielding was followed by strain hardening until a peak stress was reached at a shear strain around 1, after which work softening occurred. Weakening gradually evolved into a constant stress regime. During hardening, a shear microstructure and crystallographic preferred orientation (CPO) developed. Afterwards the volume fraction of smaller dynamic recrystallised grains increased continuously, resulting in a recrystallisation microstructure and CPO at shear strains of 5 and higher. The new D2 experiments displayed a strain variation between homogeneously deformed sample segments that increased with increasing D1 strain. The stress-strain behaviour of the D2 bulk sandwich samples showed less pronounced work-hardening and -softening when compared with single-stage deformation experiments. Furthermore, constant flow stress was attained at increasingly lower strain with increasing D1 strain. In most D2 segments, fabric development is equivalent to single-stage experiments at corresponding absolute strain. The fabrics differed markedly from those in single-stage experiments in the case of reversed two-stage deformation at moderate strain (D1 shear strain 1 and 2.6). Experiments show that grain shape by shearing of relict grains is defined by finite strain and thus affected by strain reversal. Recrystallisation is controlled by absolute strain and not influenced by strain reversal.
ISSN: 0040-1951

hal-00617686
https://hal.archives-ouvertes.fr/hal-00617686
DOI : 10.1016/j.tecto.2010.09.029

Éditeur(s) : Université de Paris 6 – Pierre et Marie Curie
Résumé : Since 1997, a new pathology seasonally occurs in new caledonian shrimp farms during the warm season and was named Summer Syndrome. Diseased Litopenaeus stylirostris shrimp suffer from a septicemic vibriosis which was attributed to V. nigripulchritudo. Preliminary studies based on a collection of V. nigripulchritudo strains have brought to light different virulence levels according to experimental infections results; three virulence statuses were defined: highly (HP), moderately (MP) and non pathogenic (NP). The aim of this work was to genetically characterize virulent V. nigripulchritudo strains. In a first step the genetic diversity of 58 V. nigripulchritudo strains was analyzed by MLST and AP-PCR, revealing a cluster of HP and MP strains, characterized by a low genetic variability and that includes all Summer Syndrome-associated isolates. This confirms the emergence of one cluster of pathogenic V. nigripulchritudo simultaneously with the emergence of the Summer Syndrome ; in a second step, 368 genetic markers of virulence were identified by a Suppressive Subtractive Hybridization performed between the genomes of a HP strain and a genetically close, NP isolate; the distribution of the screened SSH fragments was studied in 58 V. nigripulchritudo isolates by macro-array: 78 DNA fragments were selected, allowing to characterize clusters identified and pathogenic statuses; 13 are specific of the HP strains involved in Summer Syndrome. Interestingly, 10 of these markers are carried by a plasmid pSFn1 that contains sequences highly similar to those of a plasmid pAK1, detected in Vibrio shilonii, a coral pathogen. The origin and consequences of this plasmid acquisition are discussed.
Depuis 1997, les élevages de crevettes en Nouvelle-Calédonie sont confrontés à une nouvelle maladie, le Syndrome d'été, une vibriose septicémique dont l'agent étiologique est Vibrio nigripulchritudo. Les résultats d'infection expérimentale sur une collection de souches, ont montré l'existence de trois pathotypes distincts : hautement (HP), moyennement (MP) et non pathogène (NP). L'étude du polymorphisme génétique de 58 souches par typage moléculaire en MLST et AP-PCR, a mis en évidence un groupe phylogénétique particulier caractérisé par un très faible degré de variabilité génétique (confirmant l'émergence de ce groupe en parallèle à l'émergence du Syndrome d'été) et constitué uniquement de souches HP (dont toutes celles associées au Syndromed'été) et de souches MP. Afin d'identifier des marqueurs génétiques de la virulence des souches responsables du Syndrome d'été, et parmi ces marqueurs des gènes codant potentiellement pour des effecteurs de la virulence, une approche soustractive par SSH a été développée entre une souche HP de type Syndrome d'été et une souche NP : 368 marqueurs génétiques ont ainsi été mis en évidence ; la distribution de ces marqueurs a été étudiée chez les 58 souches de la collection par une approche en macroarray : 78 marqueurs ont été sélectionnés, qui permettent de caractériser les différents groupes phylogénétiques et les différents pathotypes, dont 13 fragments spécifiques des souches HP type Syndrome d'été. Parmi ces 13 fragments, 10 ont été localisés sur le plasmide pSFn1 qui a été entièrement séquencé. Ce même plasmide a été purifié uniquement des souches HP de type Syndrome d'été. Par ailleurs, une très forte homologie a été mise en évidence entre pSFn1 et pAK1, un autre plasmide également séquencé et retrouvé chez la souche V. shilonii AK1, responsable du blanchiment du corail Oculina patagonica en Méditerranée. Ces résultats ont ouvert la discussion sur le rôle de pSFn1 dans la virulence de V. nigripulchritudo.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2008/these-3906.pdf
http://archimer.ifremer.fr/doc/00000/3906/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We measure throw distributions for graben-bounding normal faults from two areas on Mars to investigate fault growth, displacement-length (D-max-L) scaling, and extensional strain using a complementary suite of techniques. Faults in the northern plains are inferred to be restricted at 2-3 km depth, as shown by a transition from linear scaling, with D-max-L ratios of similar to 1 x 10(-3), to nonlinear scaling for faults >50 km long. On the Alba Patera volcano, faults conform to linear Dmax-L scaling, with a Dmax-L ratio of similar to 6 x 10(-3), consistent with more deeply penetrating faults that are not restricted at depth. These grabens accommodate larger extensional strains (similar to 0.84%) than the faults in the northern plains (similar to 0.23%), with a temporal change from regionally distributed to localized deformation and associated increases in D-max-L ratio extensional strain, and perhaps down-dip fault height. The results suggest that both spatial and temporal variations in extensional strain and displacement-length scaling relations, along with fault restriction, are recorded by Martian fault populations. (C) 2009 Elsevier Ltd. All rights reserved.
ISSN: 0191-8141

hal-00420888
https://hal.archives-ouvertes.fr/hal-00420888
DOI : 10.1016/j.jsg.2009.03.016

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study presents microstructural evidence for deformation-controlled melt organization and for changes in olivine deformation associated with the presence of melt in an 80 m vertical section of the crust-mantle transition zone in the Oman ophiolite. This zone represents an 'end member' case for analyzing feedbacks between deformation and melt distribution in the upper mantle, since it experienced strong shear strains in presence of large melt fractions. It is characterized by a subhorizontal compositional layering at the mm to meter scale, from weakly impregnated dunites to olivine-rich gabbros, which parallels a pervasive foliation containing a strong stretching lineation. The parallelism between the compositional layering and the foliation, the diffuse limits of the layers, the alignment of elongated plagioclase-rich aggregates devoid of internal deformation structures with the elongation of olivine crystals in the dunitic layers, and the sharp compositional changes across some, but not all layer limits suggest deformation plays an essential role on the development of the layering. The variation on a mm-scale of the olivine crystal preferred orientation (CPO) symmetry as a function of the modal content: from axial-[100] symmetry in layers with <70% modal olivine to axial-[010] in more gabbroic levels (<40% olivine), which is repeated over the entire section, implies deformation in presence of variable melt fractions. Axial-[100] olivine CPO in olivine-rich layers is consistent with deformation by dislocation creep under high temperature, low pressure, dry conditions. Axial-[010] olivine CPO patterns imply additional sliding along preferentially wetted (010) grain boundaries, increase in the activity of [001] glide, or transpression localized in the melt-rich layers. Since the change in CPO symmetry is not accompanied by dispersion, instantaneous melt fractions must have remained <30-40% in all layers. The continuous variation in olivine CPO symmetry with decreasing olivine content implies therefore that the former depends on the cumulated strain in presence of melt rather than on the instantaneous melt fraction.
ISSN: 0012-821X

hal-00795508
https://hal.archives-ouvertes.fr/hal-00795508
DOI : 10.1016/j.epsl.2012.10.003

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy P - Oxford Open Option A Oxford University Press (OUP)
Résumé : International audience
The Pyrenean mountain range is a slowly deforming belt with continuous and moderate seismic activity. To quantify its deformation field, we present the velocity field estimated from a GPS survey of the Pyrenees spanning 18 yr. The PotSis and ResPyr networks, including a total of 85 GPS sites, were installed and first measured in 1992 and 1995–1997, respectively, and remeasured in 2008 and 2010. We obtain a deformation field with velocities less than 1 mm yr−1 across the range. The estimated velocities for individual stations do not differ significantly from zero with 95 per cent confidence. Even so, we estimate a maximum extensional horizontal strain rate of 2.0 ± 1.7 nanostrain per year in a N–S direction in the western part of the range. We do not interpret the vertical displacements due to their large uncertainties. In order to compare the horizontal strain rates with the seismic activity, we analyse a set of 194 focal mechanisms using three methods: (i) the ‘r’ factor relating their P and T axes, (ii) the stress tensors obtained by fault slip inversion and (iii) the strain-rate tensors. Stress and strain-rate tensors are estimated for: (i) the whole data set, (ii) the eastern and western parts of the range separately, and (iii) eight zones, which are defined based on the seismicity and the tectonic patterns of the Pyrenees. Each of these analyses reveals a lateral variation of the deformation style from compression and extension in the east to extension and strike-slip in the west of the range. Although the horizontal components of the strain-rate tensors estimated from the seismic data are slightly smaller in magnitude than those computed from the GPS velocity field, they are consistent within the 2σ uncertainties. Furthermore, the orientations of their principal axes agree with the mapped active faults.
ISSN: 0956-540X

hal-01171752
https://hal.archives-ouvertes.fr/hal-01171752
DOI : 10.1093/gji/ggv052

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
*Context: Tree orientation is controlled by asymmetric mechanical stresses set during wood maturation. The magnitude of maturation stress differs between longitudinal and tangential directions, and between normal and tension woods. * Aims: We aimed at evaluating patterns of maturation stress on eucalypt plantation trees and their relation with growth, with a focus on tangential stress evaluation. * Methods: Released maturation strains along longitudinal and tangential directions were measured around the circumference of 29 Eucalyptus nitens trees, including both straight and leaning trees. * Results: Most trees produced asymmetric patterns of longitudinal maturation strain but more than half of the maturation strain variability occurred between trees. Many trees produced high longitudinal tensile stress all around their circumference. High longitudinal tensile stress was not systematically associated with the presence of gelatinous layer. The average magnitude of released longitudinal maturation strain was found negatively correlated to the growth rate. A methodology is proposed to ensure reliable evaluation of released maturation strain in both longitudinal and tangential directions. Tangential strain evaluated with this method was lower than previously reported. * Conclusion: The stress was always tensile along longitudinal direction and compressive along tangential direction, and their respective magnitude was positively correlated. This correlation does not result from a Poisson effect but may be related to the mechanism of maturation stress generation.
Annals of Forest Science

hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611/document
DOI : 10.1007/s13595-013-0318-4

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Background and Aims: In rain forests, sapling survival is highly dependent on the regulation of trunk slenderness (height/diameter ratio): shade-intolerant species have to grow in height as fast as possible to reach the canopy but also have to withstand mechanical loadings (wind and their own weight) to avoid buckling. Recent studies suggest that mechanosensing is essential to control tree dimensions and stability-related morphogenesis. Differences in species slenderness have been observed among rainforest trees; the present study thus investigates whether species with different slenderness and growth habits exhibit differences in mechanosensitivity. Methods: Recent studies have led to a model of mechanosensing (sum-of-strains model) that predicts a quantitative relationship between the applied sum of longitudinal strains and the plant's responses in the case of a single bending. Saplings of five different neotropical species (Eperua falcata, E. grandiflora, Tachigali melinonii, Symphonia globulifera and Bauhinia guianensis) were subjected to a regimen of controlled mechanical loading phases (bending) alternating with still phases over a period of 2 months. Mechanical loading was controlled in terms of strains and the five species were subjected to the same range of sum of strains. The application of the sum-of-strain model led to a dose-response curve for each species. Dose-response curves were then compared between tested species. Key Results: The model of mechanosensing (sum-of-strain model) applied in the case of multiple bending as long as the bending frequency was low. A comparison of dose-response curves for each species demonstrated differences in the stimulus threshold, suggesting two groups of responses among the species. Interestingly, the liana species B. guianensis exhibited a higher threshold than other Leguminosae species tested. Conclusions: This study provides a conceptual framework to study variability in plant mechanosensing and demonstrated interspecific variability in mechanosensing.
ISSN: 0305-7364

halsde-00454145
https://hal.archives-ouvertes.fr/halsde-00454145
DOI : 10.1093/aob/mcp286

Éditeur(s) : HAL CCSD
Résumé : International audience
We present a new 3-D GPS velocity solution for 182 sites for the region encompassing the Western Alps, Pyrenees, and southern France. The velocity field is based on a Precise Point Positioning (PPP) solution, to which we apply a common-mode filter, defined by the 26 longest time series, in order to correct for network-wide biases (reference frame, unmodeled large-scale processes, etc.). We show that processing parameters, such as troposphere delay modeling, can lead to systematic velocity variations of 0.1–0.5 mm yr−1 affecting both accuracy and precision, especially for short (< 5 years) time series. A velocity convergence analysis shows that minimum time-series lengths of  ∼  3 and  ∼  5.5 years are required to reach a velocity stability of 0.5 mm yr−1 in the horizontal and vertical components, respectively. On average, horizontal residual velocities show a stability of  ∼  0.2 mm yr−1 in the Western Alps, Pyrenees, and southern France. The only significant horizontal strain rate signal is in the western Pyrenees with up to 4  ×  10−9 yr−1 NNE–SSW extension, whereas no significant strain rates are detected in the Western Alps (< 1  ×  10−9 yr−1). In contrast, we identify significant uplift rates up to 2 mm yr−1 in the Western Alps but not in the Pyrenees (0.1 ± 0.2 mm yr−1). A correlation between site elevations and fast uplift rates in the northern part of the Western Alps, in the region of the Würmian ice cap, suggests that part of this uplift is induced by postglacial rebound. The very slow uplift rates in the southern Western Alps and in the Pyrenees could be accounted for by erosion-induced rebound.
ISSN: 1869-9529

hal-01395116
https://hal.archives-ouvertes.fr/hal-01395116
https://hal.archives-ouvertes.fr/hal-01395116/document
https://hal.archives-ouvertes.fr/hal-01395116/file/nguyen2016.pdf
DOI : 10.5194/se-7-1349-2016

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Although magmatism may occur during the earliest stages of continental rifting, its role in strain accommodation remains weakly constrained by largely 2-D studies. We analyze seismicity data from a 13 month, 39-station broadband seismic array to determine the role of magma intrusion on state-of-stress and strain localization, and their along-strike variations. Precise earthquake locations using cluster analyses and a new 3-D velocity model reveal lower crustal earthquakes beneath the central basins and along projections of steep border faults that degas CO2. Seismicity forms several disks interpreted as sills at 6-10 km below a monogenetic cone field. The sills overlie a lower crustal magma chamber that may feed eruptions at Oldoinyo Lengai volcano. After determining a new ML scaling relation, we determine a b-value of 0.87±0.03. Focal mechanisms for 65 earthquakes, and 13 from a catalogue prior to our array reveal an along-axis stress rotation of ∼60° in the magmatically active zone. New and prior mechanisms show predominantly normal slip along steep nodal planes, with extension directions ∼N90°E north and south of an active volcanic chain consistent with geodetic data, and ∼N150°E in the volcanic chain. The stress rotation facilitates strain transfer from border fault systems, the locus of early-stage deformation, to the zone of magma intrusion in the central rift. Our seismic, structural, and geochemistry results indicate that frequent lower crustal earthquakes are promoted by elevated pore pressures from volatile degassing along border faults, and hydraulic fracture around the margins of magma bodies. Results indicate that earthquakes are largely driven by stress state around inflating magma bodies.
ISSN: 1525-2027

hal-01667198
https://hal.archives-ouvertes.fr/hal-01667198
DOI : 10.1002/2017GC007027

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Active mechanisms of re-orientation are necessary to maintain the verticality of tree stems. They are achieved through the production of reaction wood, associated with circumferential variations of three factors related to cambial activity: maturation strain, longitudinal modulus of elasticity (MOE) and eccentric growth. These factors were measured on 17 mature trees from different botanical families and geographical locations. Various patterns of circumferential variation of these factors were identified. A biomechanical analysis based on beam theory was performed to quantify the individual impact of each factor. The main factor of re-orientation is the circumferential variation of maturation strains. However, this factor alone explains only 57% of the re-orientations. Other factors also have an effect through their interaction with maturation strains. Eccentric growth is generally associated with heterogeneity of maturation strains, and has an important complementary role, by increasing the width of wood with high maturation strain. Without this factor, the efficiency of re-orientations would be reduced by 31% for angiosperms and 26% for gymnosperms. In the case of angiosperms, MOE is often larger in tension wood than in normal wood. Without these variations, the efficiency of re-orientations would be reduced by 13%. In the case of gymnosperm trees, MOE of compression wood is lower than that of normal wood, so that re-orientation efficiency would be increased by 24% without this factor of variations.
ISSN: 0931-1890

hal-01031825
https://hal.archives-ouvertes.fr/hal-01031825
DOI : 10.1007/s00468-005-0407-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The interseismic velocity field provided by geodetic methods is generally interpreted in the framework of a thick elastic lithosphere with a slipping fault at depth. Because lateral variations of lithospheric rheology play a key role in determining the geological strain distribution, I examine the idea that interseismic strain rate variations also occur in response to lateral variations in the elastic thickness of the lithosphere. Using a stress balance principle and some simplifying assumptions, I show using a 1D model that elastic thickness is inversely proportional to strain rate for the simple case of pure strike-slip faulting. Elastic thickness computed on three profiles crossing the San Andreas fault system (SAFS) suggests that the distribution of interseismic strain rate is compatible with a thick elastic lithosphere in the Great Basin-Sierra Nevada province and on the Pacific plate. Conversely, a thin plate with a shallow asthenosphere is needed on the SAFS to explain its high strain rate. A 2.5D Finite Element model of interseismic strain in the Carrizo Plain region in Central California shows how known vertical and horizontal variations of elastic properties refine 1D model predictions. In a case of a multiple fault system, I point out that the interseismic velocity is not causally tied to faults slip rate. Therefore, analysing the velocity field across the SAFS cannot reliably provide faults slip rate distribution as previously claimed. Rather, the apparent correlation between geologic slip rate and interseismic strain may only indicate that the elastic thickness plays a dominant role in controlling fault strength. Finally, I suggest that interseismic geodetic strain could be a new way to infer effective elastic plate thickness on the continents.
ISSN: 0012-821X

hal-00412155
https://hal.archives-ouvertes.fr/hal-00412155
DOI : 10.1016/j.epsl.2008.01.046

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We studied the deformation in a partially molten mantle through detailed petrostructural analysis of plagioclase lherzolites from the northwestern part of the central Lanzo massif. These peridotites display a pervasive anastomosed network of millimetre to centimetre-scale plagioclase-rich bands, which grades locally into a planar layering marked by an intercalation of plagioclase-rich and olivine-rich layers up to tens of centimetres wide. Both the anastomosed and the planar layering are subparallel to the deformation fabric, characterized by a foliation defined by the shape-preferred orientation of olivine and by crystal preferred orientation (CPO) of olivine, orthopyroxene, and clinopyroxene. This parallelism, the coexistence of microstructural evidence for melt-rock reactions and for deformation by dislocation creep, and the predominance of axial-[010] olivine CPO patterns, characterized by [010] axes clustered normal to the layering, indicate that deformation and the reactive melt percolation that formed the layering were coeval. Strong heterogeneity in mineral composition in the planar layering domains, with Fe-enrichment in olivine and spinel and highly variable Ti content in spinel in cm-scale plagioclase-rich bands, implies that the latter interacted with higher melt volumes. High Ti contents in pyroxenes and spinel in the anastomosed layering domains point to changes in melt composition, hinting to less effective melt transport. We propose therefore that the planar layering records melt segregation in layers parallel to the shear plane, whereas the anastomosed layering results from melt alignment along grain boundaries subparallel to the shear plane, without segregation. Finite strain in the different layers cannot be quantified, but comparison of the present observations with data from experiments and from other mantle outcrops displaying shear-controlled melt organization suggests that the transition from the anastomosed to the planar layering might record an increase in finite strain, that is, strain localization associated with variations in the instantaneous melt fraction.
ISSN: 0040-1951

hal-01053509
https://hal.archives-ouvertes.fr/hal-01053509
DOI : 10.1016/j.tecto.2014.01.007

Éditeur(s) : HAL CCSD American Society for Microbiology
Résumé : International audience
Under physiological conditions, the liver sinusoidal endothelial cells (LSECs) mediate hepatic immune tolerance toward self or foreign antigens through constitutive expression of anti-inflammatory mediators. However, upon viral infection or Toll-like receptor 2 (TLR2) activation, LSECs can achieve proinflammatory functions, but their role in hepatic inflammation during acute viral hepatitis is unknown. Using the highly virulent mouse hepatitis virus type 3 (MHV3) and the attenuated variants 51.6-MHV3 and YAC-MHV3, exhibiting lower tropism for LSECs, we investigated in vivo and in vitro the consequence of LSEC infection on their proinflammatory profiles and the aggravation of acute hepatitis process. In vivo infection with virulent MHV3, in comparison to attenuated strains, resulted in fulminant hepatitis associated with higher hepatic viral load, tissue necrosis, and levels of inflammatory mediators and earlier recruitment of inflammatory cells. Such hepatic inflammatory disorders correlated with disturbed production of interleukin-10 (IL-10) and vascular factors by LSECs. We next showed in vitro that infection of LSECs by the virulent MHV3 strain altered their production of anti-inflammatory cytokines and promoted higher release of proinflammatory and procoagulant factors and earlier cell damage than infection by attenuated strains. This higher replication and proinflammatory activation in LSECs by the virulent MHV3 strain was associated with a specific activation of TLR2 signaling by the virus. We provide evidence that TLR2 activation of LSCEs by MHV3 is an aggravating factor of hepatic inflammation and correlates with the severity of hepatitis. Taken together, these results indicate that preservation of the immunotolerant properties of LSECs during acute viral hepatitis is imperative in order to limit hepatic inflammation and damage. IMPORTANCE Viral hepatitis B and C infections are serious health problems affecting over 350 million and 170 million people worldwide, respectively. It has been suggested that a balance between protection and liver damage mediated by the host's immune response during the acute phase of infection would be determinant in hepatitis outcome. Thus, it appears crucial to identify the factors that predispose in exacerbating liver inflammation to limit hepatocyte injury. Liver sinusoidal endothelial cells (LSECs) can express both anti- and proinflammatory functions, but their role in acute viral hepatitis has never been investigated. Using mouse hepatitis virus (MHV) infections as animal models of viral hepatitis, we report for the first time that in vitro and in vivo infection of LSECs by the pathogenic MHV3 serotype leads to a reversion of their intrinsic anti-inflammatory phenotype toward a proinflammatory profile as well to as disorders in vascular factors, correlating with the severity of hepatitis. These results highlight a new virus-promoted mechanism of exacerbation of liver inflammatory response during acute hepatitis.
ISSN: 0022-538X

hal-01390974
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01390974
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01390974/document
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01390974/file/Mouse%20Hepatitis%20Virus%20Infection_accepted.pdf
DOI : 10.1128/JVI.01069-16

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
While vertical motion induced by long-term geological loads is often used to estimate the flexural rigidity of the lithosphere, we intend to evaluate the shear rigidity of the lithosphere using horizontal motion. Our approach considers that the rigidity of the lithosphere may be defined as its resistance to horizontal tectonic lateral forces. In this case, a spatial distribution of an effective shear rigidity can be estimated from the analysis of the interseismic velocity fields. We consider the Western United States zone where weakly strained areas (e.g., the Sierra Nevada) are connected with areas of large strain rate (e.g. San Andreas Fault system). By inverting interseismic strain distribution measured by geodetic methods, we infer the effective shear rigidity of the lithosphere. The forward problem is defined using the equations of linear elasticity. The inversion relies on the minimization of the sum of a quadratic measure of the differences between measured and modelled velocity fields. The functional also includes regularization terms for the parameters of the model. The gradient of the functional with respect to the minimization parameters is computed using an adjoint formulation. This permits the treatment of large dimensional minimization problems. Finally, a measure of the uncertainty of our inversion is illustrated through the covariance matrix of the parameters at the optimum. The optimization chart is validated on two synthetic velocity distributions. Then, the effective shear rigidity variations of the Western United States are estimated using the CMM3 interseismic velocities. The inversion displays low effective rigidities along the San Andreas Fault system, the Mojave Desert and in the Eastern California Shear Zone, while rigid areas are found in the Sierra Nevada and in the South Basin and Range. Finally, we discuss the differences between our strain rate and rigidity maps with previously published results for the Western United States.
ISSN: 0040-1951

Droits : http://hal.archives-ouvertes.fr/licences/copyright/
hal-01505024
https://hal.archives-ouvertes.fr/hal-01505024
https://hal.archives-ouvertes.fr/hal-01505024/document
https://hal.archives-ouvertes.fr/hal-01505024/file/Paper_tectophysics.pdf
DOI : 10.1016/j.tecto.2017.03.015

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
International audience
The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three-dimensional strains were measured at different parts of the trunk base. Risks of failure were greater on the buttress sides, where shear and tangential stresses are greater, not on the ridges, in spite of high longitudinal (parallel to the grain) stresses. A simple beam model, computed from the second moment of area of digitized cross sections, is consistent with longitudinal strain variations but cannot predict accurately variations with height. Patterns of longitudinal strain variation along ridges are very different in the two individuals, owing to a pronounced lateral curvature in one specimen. The constant stress hypothesis is discussed based on these results. Without chronological data during the development of the tree, it cannot be proved that buttress formation is activated by stress or strain.
ISSN: 0002-9122

hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155/document
https://hal.archives-ouvertes.fr/hal-01032155/file/Biomechanics_buttressed_trees_Clair_al_2003.pdf
DOI : 10.3732/ajb.90.9.1349

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study addresses the mechanical and chemical behavior of allanite during shear zone formation under high-pressure metamorphism. Understanding physico-chemical processes related to the retention or resetting of Pb isotopes in allanite during geological processes is essential for robust petrochronology. Dating of allanite in meta-granodiorite showing variable amounts of strain (from an undeformed protolith to mylonite) at Monte Mucrone (Sesia Zone, NW Italy) gave surprising results. Based on structural and petrographic observations the shear zones at Mt Mucrone are Alpine, yet allanite located within an eclogite facies mylonite yielded Permian ages (208Pb/232Th average age: 287 ± 7 Ma). These mm-sized allanite grains are rimmed by an aggregate of coarse-grained garnet + phengite, thought to derive from former epidote. These aggregates were immersed in a weak matrix that experienced granular flow, and they were thus chemically and mechanically shielded during Alpine mylonitization. In undeformed samples (8a and 8b), two populations of epidote group minerals were found. Allanite forms either coronas around Permian monazite or individual grains with patchy zoning. Both types yield Permian ages (208Pb/232Th age: 291 ± 5 Ma). On the other hand, grains of REE-rich clinozoisite of Cretaceous age are found in undeformed rocks. These grains appear as small fragments with embayed surface outlines and minute satellites or rims around Permian allanite. These (re)crystallized grains are Sr-rich and show mosaic zoning. These results indicate that allanite crystals retained their chemical and isotopic characteristics, and thus their Permian age, as a result of strong strain partitioning between the epidote group porphyroclasts and the eclogite facies matrix in HP-mylonites. The observed partial mobilization of Pb isotopes, which lead to the Cretaceous-aged rims or grains in undeformed samples was facilitated by (re)crystallization of allanite and not by mere Pb diffusion alone under the HP conditions.
ISSN: 0024-4937

insu-00679730
https://hal-insu.archives-ouvertes.fr/insu-00679730
DOI : 10.1016/j.lithos.2011.01.005

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
IntroductionLeishmania RNA virus type 1 (LRV1) is an endosymbiont of some Leishmania (Vianna) species in South America. Presence of LRV1 in parasites exacerbates disease severity in animal models and humans, related to a disproportioned innate immune response, and is correlated with drug treatment failures in humans. Although the virus was identified decades ago, its genomic diversity has been overlooked until now.Methodology/Principles findingsWe subjected LRV1 strains from 19 L. (V.) guyanensis and one L. (V.) braziliensis isolates obtained from cutaneous leishmaniasis samples identified throughout French Guiana with next-generation sequencing and de novo sequence assembly. We generated and analyzed 24 unique LRV1 sequences over their full-length coding regions. Multiple alignment of these new sequences revealed variability (0.5%±23.5%) across the entire sequence except for highly conserved motifs within the 5' untranslated region. Phylogenetic analyses showed that viral genomes of L. (V.) guyanensis grouped into five distinct clusters. They further showed a species-dependent clustering between viral genomes of L. (V.) guyanensis and L. (V.) braziliensis, confirming a long-term co-evolutionary history. Noteworthy, we identified cases of multiple LRV1 infections in three of the 20 Leishmania isolates.Conclusions/SignificanceHere, we present the first-ever estimate of LRV1 genomic diversity that exists in Leishmania (V.) guyanensis parasites. Genetic characterization and phylogenetic analyses of these viruses has shed light on their evolutionary relationships. To our knowledge, this study is also the first to report cases of multiple LRV1 infections in some parasites. Finally, this work has made it possible to develop molecular tools for adequate identification and genotyping of LRV1 strains for diagnostic purposes. Given the suspected worsening role of LRV1 infection in the pathogenesis of human leishmaniasis, these data have a major impact from a clinical viewpoint and for the management of Leishmania-infected patients.
ISSN: 1935-2727

pasteur-01583523
https://hal-riip.archives-ouvertes.fr/pasteur-01583523
DOI : 10.1371/journal.pntd.0005764
PUBMED : 28715422

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The lithospheric mantle is intrinsically heterogeneous and anisotropic. These two properties govern the repartition of deformation, controlling intraplate strain localization and development of new plate boundaries. Geophysical and geological observations provide clues on the types, ranges, and characteristic length scales of heterogeneity and anisotropy in the lithospheric mantle. Seismic tomography points to variations in geothermal gradient and hence in rheological behavior at scales of hundreds of km. Seismic anisotropy data substantiate anisotropic physical properties consistent at scales of tens to hundreds of km. Receiver functions imply lateral and vertical heterogeneity at scales < 10 km, which might record gradients in composition or anisotropy. Observations on naturally deformed peridotites establish that compositional heterogeneity and Crystal Preferred Orientations (CPOs) are ubiquitous from the mm to the km scales. These data allow discussing the processes that produce/destroy heterogeneity and anisotropy and constraining the time scales over which they are active. This analysis highlights: (i) the role of deformation and reactive percolation of melts and fluids in producing compositional and structural heterogeneity and the feedbacks between these processes, (ii) the weak mechanical effect of mineralogical variations, and (iii) the low volumes of fine-grained microstructures and difficulty to preserve them. In contrast, olivine CPO and the resulting anisotropy of mechanical and thermal properties are only modified by deformation. Based on this analysis, we propose that strain localization at the plate scale is, at first order, controlled by large-scale variations in thermal structure and in CPO-induced anisotropy. In cold parts of the lithospheric mantle , grain size reduction may contribute to strain localization, but the low volume of fine-grained domains limits this effect.
ISSN: 0040-1951

hal-01277174
https://hal.archives-ouvertes.fr/hal-01277174
DOI : 10.1016/j.tecto.2015.07.026

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Middle Atlas is a region where xenolith-bearing volcanism roughly coincides with the maximum of lithospheric thinning beneath continental Morocco. It is therefore a key area to study the mechanisms of lithospheric thinning and constrain the component of mantle buoyancy that is required to explain the Moroccan topography. Samples from the two main xenolith localities, the Bou Ibalghatene and Tafraoute maars, have been investigated for their mineralogy, microstructures, crystallographic preferred orientation, and whole-rock and mineral compositions. While Bou Ibalghatene belongs to the main Middle Atlas volcanic field, in the ‘tabular’ Middle Atlas, Tafraoute is situated about 45 km away, on the North Middle Atlas Fault that separates the ‘folded’ Middle Atlas, to the South-East, from the ‘tabular’ Middle Atlas, to the North-West. Both xenolith suites record infiltration of sub-lithospheric melts that are akin to the Middle Atlas volcanism but were differentiated to variable degrees as a result of interactions with lithospheric mantle. However, while the Bou Ibalghatene mantle was densely traversed by high melt fractions, mostly focused in melt conduits, the Tafraoute suite records heterogeneous infiltration of smaller melt fractions that migrated diffusively, by intergranular porous flow. As a consequence the lithospheric mantle beneath Bou Ibalghaten was strongly modified by melt–rock interactions in the Cenozoic whereas the Tafraoute mantle preserves the record of extensional lithospheric thinning, most likely related to Mesozoic rifting. The two xenolith suites illustrate distinct mechanisms of lithospheric thinning: extensional thinning in Tafraoute, where hydrous incongruent melting triggered by decompression probably played a key role in favouring strain localisation, vs. thermal erosion in Bou Ibalghatene, favoured and guided by a dense network of melt conduits. Our results lend support to the suggestion that lithospheric thinning beneath the Atlas mountains results from the combination of different mechanisms and occurred in a piecewise fashion at a short wavelength scale.
ISSN: 0040-1951

hal-01171756
https://hal.archives-ouvertes.fr/hal-01171756
DOI : 10.1016/j.tecto.2014.11.020

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The lateral variation of the mechanical properties of continental lithosphere is an important factor controlling the localization of deformation and thus the deformation history and geometry of intraplate mountain belts. A series of three-layer lithospheric-scale analog models, with a strong domain (SD) embedded at various depths, are presented to investigate the development of topography and deformation patterns by having lateral heterogeneities within a weak continental lithosphere. The experiments, performed at a constant velocity and under normal gravity, indicate that the presence or absence of the SD controls whether deformation is localized or distributed at a lithospheric scale. Deformation and topography localize above the edges of the SD, while the SD region itself is characterized by minor amounts of surficial deformation and topography. The depth of the SD (within the ductile crust, ductile mantle lithosphere, or both) controls the pattern of deformation and thus the topography. The presence of a SD in the ductile crust or in the mantle results in limited surficial topographic effects but large variations in the Moho topography. Strong Moho deflection occurs when the SD is in the ductile crust, while the Moho remains almost flat when the SD is in the mantle. When the SD occupies the ductile lithosphere, the SD is tilted. These analog experiments provide insights into intraplate strain localization and could in particular explain the topography around the Tarim Basin, a lithospheric-scale heterogeneity north of the India-Asia collision zone.
ISSN: 0278-7407

hal-01172472
https://hal.archives-ouvertes.fr/hal-01172472
DOI : 10.1002/2014TC003756