Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The complex electrical impedance of a garnet-biotite-sillimanite residual enclave in the Neogene dacite of El Hoyazo (SE Spain) has been determined up to 978 °C at 200-300 MPa. This well studied material represents a direct sampling of the Alborán Domain thinned lower crust undergoing partial melting. The paragenesis is garnet + biotite + sillimanite + plagioclase + graphite ± cordierite coexisting with widespread (~ 10 wt.%) rhyolitic melt occurring as inclusions and interstitial glass and developed during regional anatexis at 850 ± 50 °C and 500-700 MPa. The samples were used in cyclic measurements consisting in heating-cooling ramps at progressively higher maximum temperature to observe the effect of reactions on conductivity. In the first cycle up to 850 °C at 2-3 kbar, re-melting of the interstitial glass is achieved with no additional reactions and logarithmic conductivity (S/m) is up to − 1.5. At T > 950 °C new melt with orthopyroxene + ilmenite is produced from biotite partial breakdown and the logarithmic conductivity (S/m) is up to − 0.7. Application of mixing models as Hashin-Shtrikman bounds or Archie's Law, shows that once interconnected, melt controls the electrical conductivity of the enclave. The electrical conductivity of the rock can be simulated with the electrical conductivity data obtained on the starting Matrix glass of the enclave and with the new melt. Our experimental results obtained on a graphitic metasedimentary material evidence show that graphite does not contribute to the conductivity enhancement and that the electrical anomaly observed below the Betics can be explained as effect of partial melting of a residual crust. Comparison with previous works on mafic granulites shows that similar conductivity values can be achieved both by melting of a residual felsic crust or by melting of mafic materials and suggests that pelitic rocks can be more common at deep levels than expected.
ISSN: 0040-1951

hal-00823063
https://hal.archives-ouvertes.fr/hal-00823063
DOI : 10.1016/j.tecto.2012.11.003

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Previous work has demonstrated that geoelectrical measurements, acquired either along the Earth’s surface or in boreholes, can be sensitive to the presence of fractures. However, a lack of numerical approaches that are well suited to modelling electric current flow in fractured media prevents us from systematically exploring the links between geoelectrical measurements and fractured rock properties. To address this issue, we present a highly computationally efficient methodology for the numerical simulation of geoelectrical data in 2.5-D in complex fractured domains. Our approach is based upon a discrete-dual-porosity formulation, whereby the fractures and rock matrix are treated separately and coupled through the exchange of electric current between them. We first validate our methodology against standard analytical and finite-element solutions. Subsequent use of the approach to simulate geoelectrical data for a variety of different fracture configurations demonstrates the sensitivity of these data to important parameters such as the fracture density, depth, and orientation.
ISSN: 0956-540X

hal-01622151
https://hal.archives-ouvertes.fr/hal-01622151
https://hal.archives-ouvertes.fr/hal-01622151/document
https://hal.archives-ouvertes.fr/hal-01622151/file/sanzGJI2017.pdf
DOI : 10.1093/gji/ggx080

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : Ants have evolved venoms rich in peptides and proteins used for predation, defense, and communication. However, they remain extremely understudied due to the minimal amount of venom secreted by each ant. The present study investigated the differences in the proteome and peptidome of the venom from the bullet ant, Paraponera clavata. Venom samples were collected from a single colony either by manual venom gland dissection or by electrical stimulation and were compared using proteomic methods. Venom proteins were separated by 2D-PAGE and identified by nanoLC-ESI-QTOF MS/MS. Venom peptides were initially separated using C18 reversed-phase high-performance liquid chromatography, then analyzed by MALDI-TOF MS. The proteomic analysis revealed numerous proteins that could be assigned a biological function (total 94), mainly as toxins, or roles in cell regulation and transport. This investigation found that ca. 73% of the proteins were common to venoms collected by the two methods. The peptidomic analysis revealed a large number of peptides (total 309) but with <20% shared by the two collection methods. There was also a marked difference between venoms obtained by venom gland dissection from different ant colonies. These findings demonstrate the rich composition and variability of P. clavata venom.
ISSN: 1535-3893

hal-01603415
https://hal.archives-ouvertes.fr/hal-01603415
DOI : 10.1021/acs.jproteome.6b00948
PRODINRA : 406775
PUBMED : 28118015

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Benthic microbial fuel cells (BMFCs) are continuous electricity generators using electroactive microorganisms and organic matter from aquatic environment, respectively, as catalysts and substrate. In this paper, first a low-cost PVC-made structure is constructed to harvest electricity from mangrove environment located in French Guiana. An in situ BMFC has given power density of 30 mW/m2 of the anodic surface area. This performance has been confirmed by experience in laboratory where inter-electrode distance and electrode surface area appeared to be power increasing factors. However, the output power of one BMFC is not used to supply real devices such as autonomous sensors. Second, to meet this expectation, in parallel and in series associations were considered. These associations were made in order to increase the output voltage and consequently the power, to reach levels that can supply small sensors (about 3 V). Finally, to improve the performance of the series association and to avoid the voltage reversal phenomenon, a voltage balancing circuit was simulated and added to the series connections. With balancing method, the cell voltage of BMFCs can be equalized, and the performances can be improved. This allows an optimal energy harvesting and a better global efficiency of the set.
ISSN: 0363-907X

hal-01683128
https://hal.univ-antilles.fr/hal-01683128
DOI : 10.1002/er.3270

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Electrical resistivity soundings are used by geophysicists to determine the structure and composition of the Earth's crust and mantle and to explore natural resources (ore, oil, gas, water). Their interpretations in terms of composition and in-situ physical conditions depend mainly on laboratory measurements of electrical conductivity of rocks at simulated crustal conditions of temperature, pressure, saturation and pore pressures. These measurements present a numbers of limitations, in particular, in the case where conductive pore fluids are present, as in the case of deep reservoir conditions, where temperature exceeds 250 A degrees C. Here, we present a new cell capable of measuring electrical conductivity of large saturated samples at confining pressure up to 200 MPa, pore pressure up to 50 MPa, and temperature up to 500 A degrees C. The measurement cell has been developed in a commercial, internally heated, gas pressure apparatus (Paterson press). It is based on the concept of "guard ring" electrode, which is adapted to samples that are jacketed by a very conductive, metallic material. Numerical modeling of the current flow in the electrical cell allowed defining the optimal cell geometry. Calibration tests have been performed on Fontainebleau sandstones saturated with electrolytes of different conductivities, up to 350 A degrees C. The resulting electrical formation factor and temperature dependence of electrical conductivity are in very good agreement with previous studies. This new cell will improve the exploration and exploitation of deep fluid reservoirs, as in unconventional, high enthalpy geothermal fields. In particular, the investigations address possible effects of fluid-rock interactions on electrical resistivity of a reservoir host rock.
ISSN: 0169-3913

hal-00681997
https://hal.archives-ouvertes.fr/hal-00681997
DOI : 10.1007/s11242-011-9846-2

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wind energy production is very sensitive to turbulent wind speed. Thus rapid variation of wind speed due to changes in the local meteorological conditions can lead to electrical power variations of the order of the nominal power output, in particular when wind power variations on very short time scales, range at few seconds to 1 h, are considered. In small grid as they exist on islands (Guadeloupean Archipelago: French West Indies) such fluctuations can cause instabilities in case of intermediate power shortages. The developed analysis in [14] reveals three main classes of time series for the wind speed fluctuations. In this work, Probability Density Functions (PDFs) are proposed to fit the wind speed fluctuations distributions in each class. After, to simulate wind speed fluctuations sequences, we use a stochastic differential equation, the Langevin equation considering Gaussian turbulence PDF (class I), Gram–Charlier PDF (class II) and a mixture of gaussian PDF (class III). The statistical and dynamical properties of simulated wind sequences are close to those of measured wind sequences, for each class
ISSN: 0306-2619

hal-01527885
https://hal.archives-ouvertes.fr/hal-01527885
DOI : 10.1016/j.apenergy.2012.05.007

Éditeur(s) : HAL CCSD
Résumé : International audience
This paper presents a microfluidic system, characterizing the red blood cell (RBC) deformability through its transit time in a microchannel, which dimensions reproducing blood microcirculation capillary. Electrodes are integrated within the microchannel for electrical measurements. The transit time is measured with the electrical blockade produced when the RBC squeezes in the microchannel (d = 5 μm diameter, while the cell diameter is 8 μm). In order todetermine most suitable electrical frequency range for the voltage applied to excitation electrodes, FEM numerical simulation of the bioimpedance is achieved and presented in this paper. We investigated the frequency response of the bioimpedance taking into account the electrode polarization, the dielectric properties of the medium, a single shell model for RBC and finally the RBC position within the microchannel.
Eurosensors
Paris, France

hal-01592142
https://hal.archives-ouvertes.fr/hal-01592142
DOI : 10.3390/proceedings1040517

Éditeur(s) : HAL CCSD Springer
Résumé : International audience
Wind energy production is very sensitive to turbulent wind, in particular when wind power variations range from few seconds to 1 hour, are considered. Indeed rapid changes in the local meteorological condition as observed in tropical climate can provoke large variations of wind speed. Consequently the electric grid security can be jeopardized due to these fluctuations. This is particularly the case of island networks as in the Guadeloupean archipelago (French West Indies) where the installed 20 MW wind power already represents 11% of the electrical consumption. From 1 million wind sequences of duration 10 minutes, sampled at 1 Hz during the trade season, we proceed toward two objectives: i) the characterization of the wind speed sequences, ii) the dynamical simulation of the wind sequences using Langevin equation.
Progress in Turbulence and Wind Energy IV

ISBN : 978-3-642-28968-2.
hal-01527883
https://hal.archives-ouvertes.fr/hal-01527883
DOI : 10.1007/978-3-642-28968-2-50

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
To evaluate the performance of downhole and surface geophysical monitoring methods, a series of shallow gas injection-monitoring experiments has been performed in a coastal saline aquifer at Maguelone, France. The recorded data include pressure measurements with a Westbay multilevel completion and CO2 saturation at an observation well derived from electrical resistivity with a modified Waxman-Smits (MWS) model. In this work, the aim is to develop a simulation model capturing the gas transport behavior and consistent with field data. For this purpose, the simulation of the CO2 injection experiment is carried out with two conceptual models, a homogeneous model and a heterogeneous model treated with multiple realization Monte Carlo simulations. Numerical simulator TOUGH2 with the equation of state module EOS7C is used for the simulations. Comparison of the model results with field data suggests that the pressure responses are captured with relatively good accuracy. Similarly, the model also provides an overall reasonable agreement and correct order of magnitude for predicted gas saturation values. However, as the heterogeneity pattern in the field data remains largely unknown, the model predictions can only be used to capture the mean behavior as well as to provide insights into how heterogeneity can influence the system behavior, by means of sensitivity analyses of the influence of heterogeneities on individual realizations.
ISSN: 1750-5836

hal-01467240
https://hal.archives-ouvertes.fr/hal-01467240
DOI : 10.1016/j.ijggc.2016.09.006

Éditeur(s) : HAL CCSD
Résumé : International audience
The purpose of our study is to model a geothermal reservoir. When geothermal reservoir are assumed to be composed of pure water, the transfer of mass and energy is classically described by two balance equations: mass balance equation and the energy balance equation. In addition to those equations, fluid velocity ist classically given by the Darcy law while thermodynamic properties, inferred from theoretical or empirical equations of state, are used to close the mathematical system. Once this system is closed, there exist different solutions. The first one is to solve for pressure and temperature with a variable switch to saturation in the two-phase region (e.g. TOUGH2). The second one is to solve for pressure and enthalpy to increase stability of phase transition between single and two-phase states (e.g. Hydrotherm). We adopted the second option and chose te use a splitting method to get rid of the complexity of coupling equations and a finite volume method for the spatial discretization. Selecting object-oriented languages, we developed a multi-language framework, combining Python, Fortran and a C++ implementation of IAPWS (from the freesteam project) including the supercritical equations, in porous media velocity is given by Darcy law and to close the system physical properties are determined by the IAPWS-IF97 thermodynamic formulation. We resolve the equations in pressure and enthalpy instead of pressure and temperature in order to increase stability and to handle easier the passage from a single-phase to a two-phase system. We solve the system by using a splitting method - to get rid of the complexity of coupling equations - and a finite volume method. We offer some freedom to users thanks to the implementation of several methods like explicit or implicit Euler, Runge-Kutta or BDF2 for time solvers or GMRES and BICGSTAB for the linear solver. We can handle several boundary conditions like no-flow - describing a boundary which can not exchange matter with the exterior - or like a mixed-therm condition - a Dirichlet condition to the pressure and a Dirichlet or an outflow condition to the temperature in order to describe a recharge or a discharge zone - ... We're developing a multi-language framework, combining Python, Fortran and the C++ implementation of IAPWS (from the freesteam project). All these languages are object-oriented. We've applied this simulation model to the dogger in Paris, France, to several one-dimensional systems and a two-dimensional one made by Coumou with the CSMP++ platform. The dogger is a reservoir exploited to produce heat by pumping water at 70 and reinjecting it in the reservoir at 40. In the one-dimensional systems we wanted to observe the process of heat transfer from a higher temperature boundary to a smaller one in a high-energy domain. The last simulation shows the natural convection of water in a fault. For every simulation we compared the solutions we found with an other code (TOUGH2 or CSMP++) and they agreed. The next step will be to model the geothermal plant in Guadeloupe, West Indies. It's the only place in France - and in the West Indies so far - producing electricity with the earth power. The temperature can reach up to 1000 and the pressure range is around a few hundreds MPa. In some surface zones we can see two-phase water at atmospheric pressure. In the 1980s Bouillante was a laboratory for France. Since 1995 Bouillante has given 30GWh electricity a year to the Guadeloupeans.
PROCEEDINGS, Thirty-Ninth Workshop on Geothermal Reservoir Engineering
Stanford, United States

Droits : info:eu-repo/semantics/OpenAccess
hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133/document
https://hal-brgm.archives-ouvertes.fr/hal-00944133/file/Copol.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper aims to present an overview on the influence of rheological heterogeneity and mechanical anisotropy on the deformation of continents. After briefly recapping the concept of rheological stratification of the lithosphere, we discuss two specific issues: (1) as supported by a growing body of geophysical and geological observations, crust=mantle mechanical coupling is usually efficient, especially beneath major transcurrent faults which probably crosscut the lithosphere and root within the sublithospheric mantle; and (2) in most geodynamic environments, mechanical properties of the mantle govern the tectonic behaviour of the lithosphere. Lateral rheological heterogeneity of the continental lithosphere may result from various sources, with variations in geothermal gradient being the principal one. The oldest domains of continents, the cratonic nuclei, are characterized by a relatively cold, thick, and consequently stiff lithosphere. On the other hand, rifting may also modify the thermal structure of the lithosphere. Depending on the relative stretching of the crust and upper mantle, a stiff or a weak heterogeneity may develop. Observations from rift domains suggest that rifting usually results in a larger thinning of the lithospheric mantle than of the crust, and therefore tends to generate a weak heterogeneity. Numerical models show that during continental collision, the presence of both stiff and weak rheological heterogeneities significantly influences the large-scale deformation of the continental lithosphere. They especially favour the development of lithospheric-scale strike-slip faults, which allow strain to be transferred between the heterogeneities. An heterogeneous strain partition occurs: cratons largely escape deformation, and strain tends to localize within or at the boundary of the rift basins provided compressional deformation starts before the thermal heterogeneity induced by rifting are compensated. Seismic and electrical conductivity anisotropies consistently point towards the existence of a coherent fabric in the lithospheric mantle beneath continental domains. Analysis of naturally deformed peridotites, experimental deformations and numerical simulations suggest that this fabric is developed during orogenic events and subsequently frozen in the lithospheric mantle. Because the mechanical properties of single-crystal olivine are anisotropic, i.e. dependent on the orientation of the applied forces relative to the dominant slip systems, a pervasive fabric frozen in the mantle may induce a significant mechanical anisotropy of the whole lithospheric mantle. It is suggested that this mechanical anisotropy is the source of the so-called tectonic inheritance, i.e. the systematic reactivation of ancient tectonic directions; it may especially explain preferential rift propagation and continental break-up along pre-existing orogenic belts. Thus, the deformation of continents during orogenic events results from a trade-off between tectonic forces applied at plate boundaries, plate geometry, and the intrinsic properties (rheological heterogeneity and mechanical anisotropy) of the continental plates.
ISSN: 0040-1951

hal-01389719
http://hal.univ-reunion.fr/hal-01389719
http://hal.univ-reunion.fr/hal-01389719/document
http://hal.univ-reunion.fr/hal-01389719/file/vauchez_etal_rheology_1998_hal.pdf
DOI : 10.1016/S0040-1951(98)00137-1