Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A set of four reactive flow-through experiments at temperature T = 100 degrees C and total pressure P=12 MPa was performed in limestone reservoir samples. By using various ranging from 0.7 to 10 MPa, these experiments mimic mass transfers occurring (1) near the injection well, where the brine is almost saturated with CO2 (i.e. P-CO2 approximate to P), and (2) at increasing distances from the injection well, where the fluid displays lower values and higher divalent cation concentrations due rock dissolution along the fluid pathway. Results for P-CO2 = 10 MPa show non-uniform dissolution features associated with transport-controlled mass transfer, while reaction-controlled uniform dissolution is observed for P-CO2 = 2.5 MPa. The experiment with P-CO2 = 6 MPa allows investigating in detail the transition from transport-to reaction-controlled dissolution. Conversely, the experiment reproducing conditions far from the injection well (P-CO2 = 0.7 MPa), shows a decrease of porosity triggered by the precipitation of Mg-rich calcite. For all the dissolution experiments, the time-resolved porosity phi(t) can be modeled by a simple non-linear equation including parameters that characterise the dissolution regime triggered by the reactivity of the inlet fluid (measured by the Damkohler number, Da). Furthermore, all dissolution experiments display power scaling between permeability (k) and porosity (phi) with distinctly different scaling exponents characterising the reactivity of the fluid percolating the sample, independently from the decrease with time of the reactive surface area. It is shown also that dissolution at moderate positive values of Da seems the most efficient to increase permeability and promote a rapid spreading of the reaction front, while inducing minimal modification of the porosity in the vicinity of the CO2 injection well. These results can be used to parameterize the k-phi function for modeling the earliest dissolution processes occurring in the vicinity of the reaction front.
ISSN: 0009-2541

hal-00445277
https://hal.archives-ouvertes.fr/hal-00445277
DOI : 10.1016/j.chemgeo.2009.03.028

Éditeur(s) : HAL CCSD
Résumé : In order to minimize CO2 atmospheric concentration, a solution consists in sequestrating CO2 in geological reservoirs. To estimate long term risks, it is necessary to quantify the couplings between reaction processes as well as structural and hydrodynamical modifications. We realised two experimental benches enabling injecting CO2-enriched-brine in conditions corresponding to in situ storage (T < 200 oC and P < 200 bar) and developed
an experimental protocol using X-Ray microtomography and fluid and rock analyses in order to measure the variations of physical and chemical parameters.
The study of carbonated reservoirs near the injection well, allows quantifying different k-phi relationships depending on the dissolution processes and triggered by the local fluid chemical composition and initials conditions. Away from the injection well, we observe carbonate precipitation decreasing the permeability. The study of fracturated caprock samples shows that alternative percolation of CO2-enriched-brine and CO2 gas increases the fracture permeability.
The study of silicated rocks indicates carbonate precipitation in zeolite sandstone and sintered dunite grains. Nevertheless, in zeolite sandstone we also observe the precipitation of clay particles located in the uid pathways which decrease strongly the permeability.
Afin de minimiser la concentration en CO2 dans l'atmosphère une solution consiste à le séquestrer dans les réservoirs géologiques. Pour évaluer les risques à long terme, il est nécessaire de quantifier les couplages entre les processus réactionnels et les modifications structurales et hydrodynamiques. Dans cette optique, nous avons construit deux dispositifs expérimentaux permettant d'injecter des saumures chargées en CO2 dans les conditions de stockage (T < 200 °C et P < 200 bar) et mis en oeuvre un protocole expérimental utilisant la microtomographie RX et l'analyse des roches et des fuides pour quantifier les variations des paramètres physiques et chimiques. Dans le cas des réservoirs carbonatés, on observe, près du puits d'injection, une forte variabilité des relations k-phi en fonction du régime de dissolution contrôlé par la chimie locale du fluide, ainsi que par les conditions initiales. A plus grande distance, on observe des processus de précipitation diminuant fortement la perméabilité. L'étude des roches de couverture fracturées (argilite) a montré qu'une percolation alternée d'une saumure chargée en CO2 et de CO2 gaz augmentait la perméabilité de fracture. Dans le cas des roches silicatées, la précipitation de carbonates est mise en évidence aussi bien dans les grès à zéolites que dans les frittés de dunite de San Carlos. Cependant, dans les grès à zéolites, la précipitation d'une phase argileuse est observée dans les chemins d'écoulement et engendre une forte diminution de la perméabilité.
https://tel.archives-ouvertes.fr/tel-00416408

tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408/document
https://tel.archives-ouvertes.fr/tel-00416408/file/These_Luquot.pdf

Éditeur(s) : HAL CCSD
Résumé : Geological storage of CO2 is one of diverse technologies being explored to reduce atmospheric carbon fromindustrial processes (i.e. fossil fuel combustion). One of the specific features of CO2 injection is the possibility ofgeochemical reactions (dissolution – precipitation) between mobile reactive brine (e.g. formation water enrichedin CO2) and the host rock during the spatial and temporal evolution of CO2. That leads to modifications in thepore structure, which in turn change the flow dynamics of the reservoir (e.g. the permeability k). Then, thesesstructural modifications can largely control the injectivity, so that the pressure field in the reservoir and also theCO2 propagation. Accordingly, it is crucial to explore the changes in the reservoir properties (e.g. structural andhydrodynamic) induced during a CO2 injection and specially the relationships between them (e.g. k or reactivesurface-Sr versus porosity-φ , k versus rock heterogeneity), for developing predictive modelling tools of thetransport and reaction processes occurring during a CO2 injection and reliable risk assessment. In the case ofcarbonate rocks, the application of the predictive models of transport and reaction is still challenging, because oftheir high heterogeneity so that the incertitude in the reaction kinetics of carbonate minerals.From this perspective, we realized brine-enriched in CO2 percolation experiments through carbonate rocksamples in thermodynamic conditions expected during CO2 injection in deep reservoirs (T = 100°C et P =12MPa). The permeability changes k(t) is monitored during the experiments and the porosity variationφ (t) iscalculated from chemical analyses of the sampled outlet fluids, using ICP-EAS. The pore structure modificationsare investigated from high resolution X ray micro tomography images acquired from the synchrotron ofGrenoble (ESRF). Depending to the dissolution regime, controlled by the reservoir rock fabric and the chemicalcomposition of the brine (e.g. PCO2), we observed that a modification of pore structure can either improve(atypical result in dissolution context) or impair the value of the permeability k.
Le stockage géologique du CO2 est l’une des diverses technologies étant explorées afin deréduire les émissions de carbone atmosphérique des processus industriels (i.e. combustion del’énergie fossile). L’une des spécifiques caractéristiques de l’injection du CO2 en profondeurreste la possibilité de réactions géochimiques (dissolution-précipitation) entre la saumureréactive mobile (e.g. eau de formation enrichie en CO2) et la roche encaissante durantl’évolution spatiale et temporelle du CO2, conduisant à des modifications dans la structure despores et par conséquent dans les propriétés d’écoulement du réservoir (e.g. la perméabilité k).Donc, ces changements structuraux peuvent largement contrôler l’injectivité, ainsi que lechamp de pression dans le réservoir et aussi la propagation du CO2. Il demeure ainsi cruciald’explorer les changement dans les propriétés de réservoirs (e.g. structurales ethydrodynamiques) induits durant une injection de CO2 et explicitement les relations existantesentre eux (e.g. k ou surface réactive-Sr versus porosité-φ , k versus hétérogénéité de la roche),afin de développer des outils de modélisation prédictive des processus de transport etréactionnels se produisant durant une injection de CO2 et d’évaluer de façon fiable les risques.Dans le cas des réservoirs carbonatés, l’application des modèles prédictifs de transport réactifdemeure toujours un enjeu, car contrainte par la forte hétérogénéité en leur sein ainsi que parl’incertitude dans la cinétique de réactions des minéraux carbonatés dans ce contexte. Danscette optique, nous avons réalisé des expériences de percolation à travers des échantillons deroches carbonatées dans les conditions thermodynamiques de stockage en profondeur (T =100°C et P =12 MPa). L’évolution de la perméabilité k(t) est suivie au cours desexpériences ; et la variation de la porosité φ (t) est calculée à partir des résultats d’analyseschimiques au ICP-AES des fluides de sortie échantillonnés. L’investigation des modificationsapportées à la structure des pores est réalisée par le biais de la Micro-Tomographie hauterésolution à rayon X, acquise au synchrotron de Grenoble (e.g. ESRF).Dépendant du régime de dissolution, contrôlé par la fabrique de la roche réservoir et lacomposition chimique de la saumuré chargée en CO2 (e.g. PCO2 engagée), on a observéqu’une modification de la structure de la roche peut soit améliorer soit détériorer (résultatatypique en contexte de dissolution) la valeur de la perméabilité k.
https://hal.archives-ouvertes.fr/tel-01142136

tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136/document
https://hal.archives-ouvertes.fr/tel-01142136/file/thesemangane2013.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Underground CO2 sequestration is highly recommended as an effective means of significantly decreasing CO2 concentration in the atmosphere. Mineral storage is the more secure technology, but requires the presence of high concentration of divalent cations in the pore-fluid. Results from CO2 percolation experiments through chlorite/zeolite-rich sandstone samples from the Pretty Hill Formation (Otway Basin, Australia) are presented. The dissolution of the laumontite (7 wt.%) and chamosite (7 wt.%) are the potential sources of calcium, iron and magnesium required for carbonate precipitation. The percolation experiment was setup to reproduce, at laboratory scale, the in situ temperature and pressure conditions (T = 95 degrees C and P = 10 MPa). The fluid injected at constant flow rate is a rock-equilibrated brine subsequently enriched in CO2 up to partial pressure of 6 MPa. We observe feldspars, laumontite and chamosite dissolution, kaolinite and silica precipitation and a noticeable sink of CO2 in the sample which is attributed to the precipitation of both amorphous carbon due to the reduction of CO2 and Fe-rich carbonate. Permeability decreases of about one order of magnitude due to the localization of the kaolinite precipitation in the main flow paths, while porosity increases. The high reactivity of this sandstone makes this reservoir a valuable target for CO2 mineralization, but the associated permeability decrease may limit the injection rate and the spreading of the CO2 in the reservoir.
ISSN: 0009-2541

hal-00712829
https://hal.archives-ouvertes.fr/hal-00712829
DOI : 10.1016/j.chemgeo.2011.11.018

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A shallow field experimental site for CO2 injection was established at Maguelone (Languedoc, France), in order to test in an integrated manner a suite of surface and downhole hydrogeophysical monitoring methods. The objective is to improve monitoring of gas transport in the shallow subsurface and to determine the sensitivity of CO2 monitoring systems for leakage detection. The site offers a natural laboratory to study the processes associated with CO2 injection in a clastic and clay-rich context saturated with saline fluids. Prior to CO2 injection, three nitrogen (N2) injections were undertaken in 2012 to measure the site response to neutral gas injection. In 2013, a volume of 111 m3 (mass of 220 kg) of CO2 was injected during 3.5 h at 15 m depth. During each experiment, the gas plumes were successfully detected from pressure monitoring, time-lapse induction logging and downhole resistivity monitoring with dipole–dipole array. Increases in resistivity are attributed to free gas propagation (either N2 or CO2) whereas decreases in resistivity correlate with CO2 dissolution in the pore fluid. Chemical analyses confirm this hypothesis with a decrease in pH and an increase in the concentration of dissolved species in the latter case.
ISSN: 1750-5836

hal-01355943
https://hal.archives-ouvertes.fr/hal-01355943
DOI : 10.1016/j.ijggc.2015.12.005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
To test the impact of fluid flow on the reactivity of porous (ultra-)mafic rocks, reactive percolation experiments were realized during which CO2-enriched water was injected at two different injection rates (Q = 0.1 and 1 mL h−1) through sintered analogues of olivine-accumulation zones in basaltic flows at temperature and fluid composition conditions (T = 180 °C; NaHCO3 buffered solution) favorable for CO2-mineralization (carbonation).All experiments resulted in silicate dissolution, carbonate precipitation upstream and (proto-)serpentine formation downstream indicating a decrease in the fluid reactivity along flow paths. The measured bulk carbonation rates ranged from 4 to 7 × 10−8 s−1; these values were significantly lower than previously published values of olivine carbonation rate obtained on powders in closed batch and flow-through reactors. Our study show complex couplings, at pore scale, between fluid flow, localization of reaction zones, and chemical reaction kinetics which in turn control hydrodynamic properties, carbonation rate and efficiency and fluid reactivity. This results in carbonation rates being higher when injection rates are high and permeability ultimately controlling carbonation reactions by limiting fluid input. During experiments, notable changes in permeability occurred for only minor changes in porosity indicating a control by the geometry of the porous network: heterogeneities in the distribution of flow paths favored the localization of precipitated minerals which in turn resulted in the closure of flow paths. This mechanism was particularly efficient at low injection rates. These results imply that controlling the injection rate could allow enhancing/limiting the efficiency of in situ carbonation.
ISSN: 0883-2927

hal-01115284
https://hal.archives-ouvertes.fr/hal-01115284
DOI : 10.1016/j.apgeochem.2014.11.024

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Heletz sandstone (Israel) reactivity is studied by means of CO2-rich brine percolation experiments and modeling. Experiments are performed at in situ temperature and pressure conditions with two distinctly different injection flow rates and for two different brine compositions: the genuine Heletz brine and a similar brine but in equilibrium with gypsum. The Heletz sandstone is composed of quartz, dolomite, ankerite, K-feldspar, clay minerals and minor amounts of gypsum and pyrite. The main reaction is the dissolution of the carbonates which is fastest for the highest flow rate injection and for the genuine Heletz brine. Permeability increases during the five percolation experiments, regardless of flow rate and brine type. This increase in permeability is associated to a decrease in porosity during the gypsum-equilibrated brine experiments due to gypsum precipitation. The precipitation of secondary minerals (kaolinite, muscovite and smectite) is mainly controlled by the dissolution of K-feldspar and largest at low flow rate injection, indicating that these precipitation processes are diffusion-controlled and localized in immobile zones where favorable chemical micro-environments exist. These processes are quantified by means of a reactive transport model. These results indicated that the CO2 injection at the Heletz site should trigger both permeability increase in interface between brine and CO2, which may extend over a large extension and where mixing processes are very active, especially near the well under intermittent injection conditions.
ISSN: 1750-5836

hal-01356329
https://hal.archives-ouvertes.fr/hal-01356329
DOI : 10.1016/j.ijggc.2015.10.023

Éditeur(s) : HAL CCSD
Résumé : The Franceville Basin (2.1 Ga) in southeastern Gabon, hosts a black shale series well preserved (FB Formation) which represents an exceptional example of unmetamorphised Paleoproterozoic sediment strata. This basin includes the protore of one of the largest Mn-oxide laterite ore worldwide, mined by Eramet-Comilog. The aim of this this work is to determine formation conditions of this protore and to characterize the global sedimentary evolution of the FB Formation which include the protore. This 75 m thick protore is constituted of Mn carbonate-rich black shales which represent a potential ore deposit for the future. It was drilled, on the Bangombé plateau, during a recent campaign of 24 boreholes with an average depth of 125 m.Through multidisciplinary study on these cores and key outcrops of the basin, this work focuses on : i) the depositional environment of the Mn-protore and FB Formation ; ii) the processes of formation of the Mn-carbonates at 2.1 Ga and iii) the architecture and distribution of Mn-rich levels of the protore on the Bangombé Plateau.A detailed sedimentological and petrological study allowed us to redefine the division of the FB into nine units, named U1 to U9 from the base to the top. These units show a fine upward cycle up to U5 and a reverse coarse loop until U9. This division leads to a new interpretation to propose an evolution from a shoreface depositional environment controlled by deltaic currents (U1) to an offshore depositional environment with anoxic conditions (U2). In this basin, a system of submarine fan is developed, feeding a network of sand injections (injectites) covering the Bangombé plateau (70 km²) and with a thickness of 150 m affecting U4 to U7, including the Mn-protore. The protore depositional environment formed below the wave base limit (U4, U5 and U6) in a starved basin, controlled by biochemical sedimentation allowed the formation of Mn-carbonates. The end of starved basin, would allow the re-opening of the detrital input into the offshore basin (U7). This basin is then filled by storm bar deposits intersected by deltaic sub-aquatic channels (U8). The U9 unit corresponds to a quiet lagoon environment, allowing the multicellular organism development for the first time on the planet.A geochemical study allowed the characterization of the depositional environment of Mn-carbonates as an anoxic to sub-oxic and alkaline environment. For the first time, we showed that the manganese carbonates, present as bacteriomorph forms, are precipitated from the seawater by the mediated photosynthetic cyanobacterial activity, which allows CO2 / HCO3 depression of the environment and a local increase of pH. The cyanobacterial activity is controlled by the absence of bottom currents, which increase the detrital input. This would stop the activity of the cyanobacteria and thus would lead to the decrease of the Mn-concentration along the protore.Finally, well-log and a sequential correlation analyses allowed us to detail spatial and timing repartition of FB Formation deposit, controlled by a tectono-sedimentary model. We propose two- tectono-sedimentary phases. A first syn-tectonic phase (U1 to U3) controls the depocentres and sedimentation gaps. Turbidite coarse deposits are located in the most subsident part, clay deposits rather on the slope and carbonates on shoals. A second post-tectonic phase (U4 to U7) allows isopach deposits. The Mn-protore formed during the post-tectonic phase. However, it shows a variable thickness due to subsidence to the north of the Bangombé plateau. So, on the Bangombé plateau, Mn-contents increase towards the south, whereas the protore thickness increases towards the NNE. Moreover sand injectites decrease Mn-content in the eastern part of the Bangombé plateau and impact on the economic evaluation of the Mn-carbonates. Currently, the protore is structured by post-sedimentary faults, which lead to a non-continuity of the high Mn levels on the Bangombé plateau.
Le Bassin de Franceville situé au SE du Gabon présente une série de black shales (Formation FB) d'âge Paléoprotérozoïque (2,1 Ga) surmontant les grès de la Formation FA. Ce bassin peu déformé et non métamorphique représente une archive exceptionnelle des processus de dépôt de cette période de l’histoire de la Terre où la vie commence à se développer. En particulier, la Formation FB contient le protore d'un gisement mondial d'oxydes de manganèse exploité par la société Eramet-Comilog. L’objectif de ce travail est de préciser les conditions de formation de ce protore et de le replacer dans l’histoire du remplissage du bassin. Ce protore d'une épaisseur moyenne de 75 m est constitué de carbonates de manganèse ; il a fait l'objet d'une récente campagne de 24 forages carottés d'une profondeur moyenne de 125 m sur le plateau de Bangombé.A travers une approche pluridisciplinaire comprenant l'étude de ces forages et des affleurements clefs du bassin, ce travail porte sur la caractérisation i) de l'environnement de dépôt du protore et des séries qui l'encadrent (du toit du FA au toit du FB) ; ii) du mode de formation des carbonates de Mn à 2,1 Ga et iii) de l'architecture et de la répartition des hautes teneurs en Mn du protore qui représente un gisement potentiel du futur.L’étude pétro-sédimentaire détaillée a permis de distinguer neuf unités (U1 à U9) au sein de la Formation FB organisées suivant un cycle rétrogradant jusqu’à U5 puis progradant jusqu’à U9. Ce découpage montre une évolution du milieu de dépôt depuis un domaine de shoreface contrôlé par des courants deltaïques (U1) évoluant vers des dépôts d’offshore restreint (U2). Ce bassin enregistre ensuite un système de chenaux-levées turbiditiques (U3) qui alimentent un réseau d'injectites reconnu sur l’ensemble du Pl. de Bangombé et qui traverse 150 m de série (U4 à U7) en affectant le protore et ainsi les teneurs en Mn. L'environnement de dépôt du protore (U5 et U6) marque l’isolement du bassin qui devient affamé et contrôlé par une sédimentation biochimique à l’origine du dépôt des carbonates de Mn. L'Unité 7 correspond à la réouverture des apports détritiques en domaine d'offshore supérieur puis en domaine de shoreface dominé par des dépôts de tempêtes et de chenaux sous-aquatiques deltaïques (U8), et enfin lagunaire (U9) dans lequel apparaissent les premiers métazoaires de l’histoire de la planète, suivant une séquence régressive.Une étude géochimique a permis de préciser les conditions de dépôt du protore qui se forme en milieu alcalin anoxique à sub-oxique. Dans ce milieu, nous montrons pour la première fois une précipitation directe des carbonates de Mn sous forme bactériomorphe induite par l'activité photosynthétique des cyanobactéries qui consomment le CO2/HCO3 et conduisent à une augmentation du pH favorable à la formation des carbonates de Mn. L'activité cyanobactérienne est conditionnée par l’absence de courants de fond qui augmentent la turbidité du milieu et stoppent cette dernière.Les corrélations diagraphiques et séquentielles permettent de préciser la répartition spatiale et temporelle du FB permettant ainsi de replacer le protore dans l’histoire tectono-sédimentaire du bassin. Une première phase syn-tectonique (U1 à U3) contrôle l’épaisseur et la mise en place de dépôts turbiditiques dans les parties subsidentes, de dépôts argileux sur les pentes et de dépôt de carbonates sur les hauts-fonds. La seconde phase post tectonique (U4 à U7) permet la mise en place de dépôts relativement isopaques, bien que le protore enregistre une subsidence plus importante au nord du Pl. de Bangombé. On observe ainsi, sur le Plateau de Bangombé, des teneurs en Mn qui augmentent vers le sud alors que l’épaisseur du protore augmente vers le NNE. Postérieurement au dépôt du FB, le protore est structuré par des failles qui le compartimentent en touches de piano limitant ainsi sa continuité sur le Plateau de Bangombé.
https://hal.archives-ouvertes.fr/tel-01621460

tel-01621460
https://hal.archives-ouvertes.fr/tel-01621460
https://hal.archives-ouvertes.fr/tel-01621460/document
https://hal.archives-ouvertes.fr/tel-01621460/file/these_Dubois2017-MnGabon.pdf

Éditeur(s) : HAL CCSD
Résumé : The main purpose of this thesis was to characterize and to model the hydrodynamic and thermochemical processes leading to the alteration of the wellbore cement materials under borehole conditions. Percolation experiments were performed on fractured cement samples under CO2 storage conditions (60°C and 10MPa). Injection flow rate was dictated by the fracture aperture of each sample. CO2 enriched brine was flowed along the fracture aperture, and permeability changes as well as chemical evolution of major cations were continuously acquired during the experiment time. Reaction paths developed by the alteration of the cement were characterized using microtomography and ESEM images. The experiments conducted using samples presenting large fracture apertures during 5h showed that permeability was maintained constant during the experiment time. Three reacted layers were displaying by the alteration of portlandite and CSH. Long term experiment (26h) conducted with large initial fracture aperture showed a decrease of the permeability after 15hours of CO2 exposure. Otherwise, experiments performed on samples presenting narrow apertures indicated the conversion of portlandite and CSH to calcite leading to the permeability reduction and the fracture clogging. Assemblages of phases and chemical changes were modelled using GEMS-PSI speciation code. We studied also using a coupled transport-reactive model the conditions leading to the cement alteration and the formation of associated layers.
L'objectif de cette thèse était de modéliser à partir des expériences de percolation-réactive, les processus hydrodynamique et réactionnel qui gouvernent l'altération des ciments de puits. Différentes expériences ont été réalisées dans des conditions représentatives de celles du stockage du CO2. Des échantillons fracturés ont été utilisés pour injecter une saumure enrichie en CO2 à 60°C et 10MPa et à différentes pressions partielles de CO2. Le débitd'injection variait en fonction des propriétés hydrauliques de l'échantillon exposé. L'injection d'une saumure enrichie en CO2 à débit constant à travers une fracture supposée plane a permis d'étudier les modifications des propriétés hydrodynamiques et ces conséquences sur la géochimie et la microstructure du ciment altéré. L'impact dynamique de l'évolution microstructurale a été mis en évidence. Les expériences conduites sur des échantillons présentant de larges ouvertures, réalisées sur une durée de 5 h, ont montré que la perméabilité était maintenue constante le long de l'expérience. Trois couches d'altération se sont développées consécutivement à la dissolution de la portlandite et la décalcification des CSH. L'altération a entrainé la précipitation des carbonates et de la silice amorphe à proximité de la fracture. Dans le cas d'une expérience longue durée appliquant les mêmes conditions que précédemment on a observé que la croissance de la silice amorphe a entrainé la diminution de la perméabilité. Par ailleurs les expériences effectuées sur des échantillons présentant de faibles ouvertures, ont indiqué que la conversion de la portlandite en calcite conduit au colmatage de la fracture. L'évolution des assemblages de phases conduisant à la formation des carbonates et de la silice amorphe a été modélisée à partir du code géochimique GEMS. Les mécanismes de diffusion et les processus de mise en place des couches d'altération ont été étudiés à partir d'un modèle analytique et d'un modèle de transport réactif à partir du code géochimique PHREEQC.
https://tel.archives-ouvertes.fr/tel-01038034

tel-01038034
https://tel.archives-ouvertes.fr/tel-01038034
https://tel.archives-ouvertes.fr/tel-01038034/document
https://tel.archives-ouvertes.fr/tel-01038034/file/theseabdoulghafour.pdf

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : International audience
Carbonation of ultramafic rocks in geological reservoirs is, in theory, the most efficient way to trap CO2 irreversibly; however, possible feedback effects between carbonation reactions and changes in the reservoir permeability must be considered to realistically assess the efficiency and sustainability of this process. We investigated changes in the hydrodynamic properties of sintered dunite samples by means of percolation experiments, under conditions analogous to that of in situ carbonation. Our results show that carbonation efficiency is controlled by the local renewal of the reactants and the heterogeneity of the pore structure. Preferential flow zones are characterized by the formation of magnetite and of a silica-rich layer at the olivine surfaces, which eventually inhibits olivine dissolution. Conversely, sustainable olivine dissolution together with coprecipitation of magnesite, siderite, and minor Mg-TOT-phyllosilicates, occur in reduced-flow zones. Thus carbonate precipitation only decreases porosity in zones where diffusion-controlled transport is dominant. Consequently, while high flow rates will decrease the carbonation efficiency of the reservoir and low flow rates may reduce the permeability irreversibly close to the injection point, moderate injection rates will ensure a partial carbonation of the rock and maintain the reservoir permeability.
ISSN: 0013-936X

hal-00424540
https://hal.archives-ouvertes.fr/hal-00424540
DOI : 10.1021/es8018429

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
A CO2-rich brine core-flood experiment in calcite limestone for conditions representative of underground storage (P = 12 MPa and T = 100°C) was performed in order to explore the dissolution mechanisms arising at moderate CO2 partial pressure (0.3 MPa). An increase of the total porosity (φT) accompanied by a persistent permeability (k) decrease was measured. The mechanisms controlling this atypical anticorrelated k − φT relationship were investigated from the analysis of high-resolution X-ray microtomography images of the sample acquired before and after the experiment. All the evidences converge to the conclusion that the ubiquitous decrease of permeability measured during the 44 h of dissolution is due to the clogging of a fraction of the macroporosity by microporous material triggered by the rearrangement of the detached undissolved particles. This mechanism results in the development of low permeability zones bridging the macroporosity.
ISSN: 0094-8276

hal-00903585
https://hal.archives-ouvertes.fr/hal-00903585
DOI : 10.1002/grl.50595

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Saline aquifers in deep sedimentary formations are considered the primary candidates for geological storage of CO2, due to their large volumetric capacity that would be sufficient to meet the needs for CCS storage space in a global scale. In comparison to depleted oil and gas reservoirs the deep saline aquifers are, however, less investigated as there has previously been little economic interest in them. Effective methods for characterizing the storage aquifers are crucial for a successful implementation of any CCS project and therefore being developed and transferred from other applications in a various CCS projects.The objective of EU FP7 funded project MUSTANG project (A multiple space and time scale approach for the quantification of deep saline formations for CO2 storage, www.co2mustang.eu) has been to develop methods for characterizing saline aquifers and for understanding their properties. An essential part of this was establishment of a CO2 injection site at Heletz, Israel, where small-scale scientifically motivated injection experiments are planned to be carried out in presently ongoing continuation projects TRUST (http://trust-co2.org/) and CO2QUEST (www.co2quest.eu).While a large number of publications has been already produced based on the work in the MUSTANG project and its successors, and published in different journals, including this one, the objective of this Special Edition has been to gather some of the concluding work in the same journal issue. The focus has in particular been in summarizing the site characterization work carried out at the Heletz site, thereby providing readers an easy overview of the findings and characteristics of the site. In addition, some related work from some of the other sites investigated in MUSTANG project is also included, namely work from the sites Hontomin, Maguelone and a natural analog site in the North Sea. The results are intended to add to our understanding on relevant properties of geological formations as candidates for CO2 geological storage.
ISSN: 1750-5836

hal-01356326
https://hal.archives-ouvertes.fr/hal-01356326
DOI : 10.1016/j.ijggc.2016.02.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : Deficient sealing in the well cement plugs and annulus due to mechanical fracturing is an important risk of CO2 leakage from the reservoir to others permeable layers and the surface. Such situation was reproduced at laboratory scale in order to determine the hydro-chemical control on the fracture permeability. Specifically, we investigated the effect of CO2 rich-brine flowing through fractured Portland cements at T = 60 °C and P = 10 MPa and variable flow rates. We showed that carbonation process is dominant and induces permeability decrease and leakage mitigation for extremely low flow rate whereas for high flow rate injection the permeability remains constant due to the precipitation of a low density secondary Si-rich phase which maintains the initial fracture aperture. At intermediate flow rate the hydraulic aperture can increase due to the densification of the material triggered by the net precipitation of low porosity calcite. These results emphasize that more complex behaviors than those considered from batch experiments may take place in the vicinity of flowing fractures. Specifically, the redissolution of the neoformed calcite as well as the development of amorphous phases, both controlled by the CO2-rich brine renewing rate in the fracture may prevent the healing fracture.
ISSN: 1750-5836

hal-00857555
https://hal.archives-ouvertes.fr/hal-00857555
DOI : 10.1016/j.ijggc.2013.04.002

Éditeur(s) : HAL CCSD
Résumé : International audience
The injection of reactive mineral suspensions is a possible process to either reinforce or seal wells in geologic carbon sequestration sites. Among others, olivine slurries could be used as CO2-triggered cements, as they carbonate under the thermodynamic conditions of deep storage. However, injection of such slurries requires to control their initial fluidity and its evolution during the displacement. For this purpose, we have characterized the rheological evolution of olivine suspensions, of particle sizes 1−10 μm, sheared at 100 s−1, in the ranges of 10−40% for the volume fractions, 20−50 bars for the CO2 pressure, and 60-110°C for the temperature. The apparent viscosity, measured at 100 s−1, increases exponentially, with a characteristic time ranging from less than 1 h to more than 10 h, and decreasing with olivine concentration, CO2 pressure, and temperature. Moreover, a careful characterization of the slurry rheology carried out in the initial stages of slow evolution, shows that the slurry obeys a Bingham plastic law, with a yield stress ΣB, and a Bingham viscosity µB increasing from 1 to 20 Pa and from 4 to 110 mPa s, respectively, when the olivine volume fraction φ is increased from 10 to 30%. Such variations can be accounted by classical models (Wildemuth and Williams [1984]: Rheologica Acta, 23,627-635, Krieger [1972]: Advances in Colloid and Interface Science, 3, 111-136).
Environmental Progress & Sustainable Energy

hal-01054131
https://hal.archives-ouvertes.fr/hal-01054131
DOI : 10.1002/ep.11826

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Limestone dissolution by CO2 -rich brine induces critical changes of the pore network geometrical parameters such as the pore size distribution, the connectivity, and the tortuosity which govern the macroscopic transport properties (permeability and dispersivity) that are required to parameterize the models, simulating the injection and the fate of CO2 . A set of four reactive core-flood experiments reproducing underground conditions ( T=100∘C and P=12 MPa) has been conducted for different CO2 partial pressures (0.034
ISSN: 0169-3913

hal-00963597
https://hal.archives-ouvertes.fr/hal-00963597
DOI : 10.1007/s11242-013-0257-4

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
To evaluate the performance of downhole and surface geophysical monitoring methods, a series of shallow gas injection-monitoring experiments has been performed in a coastal saline aquifer at Maguelone, France. The recorded data include pressure measurements with a Westbay multilevel completion and CO2 saturation at an observation well derived from electrical resistivity with a modified Waxman-Smits (MWS) model. In this work, the aim is to develop a simulation model capturing the gas transport behavior and consistent with field data. For this purpose, the simulation of the CO2 injection experiment is carried out with two conceptual models, a homogeneous model and a heterogeneous model treated with multiple realization Monte Carlo simulations. Numerical simulator TOUGH2 with the equation of state module EOS7C is used for the simulations. Comparison of the model results with field data suggests that the pressure responses are captured with relatively good accuracy. Similarly, the model also provides an overall reasonable agreement and correct order of magnitude for predicted gas saturation values. However, as the heterogeneity pattern in the field data remains largely unknown, the model predictions can only be used to capture the mean behavior as well as to provide insights into how heterogeneity can influence the system behavior, by means of sensitivity analyses of the influence of heterogeneities on individual realizations.
ISSN: 1750-5836

hal-01467240
https://hal.archives-ouvertes.fr/hal-01467240
DOI : 10.1016/j.ijggc.2016.09.006

Éditeur(s) : HAL CCSD
Résumé : This study provides additional constraints on the relations between deformation, hydration and percolation of fluids and melts in the subcontinental lithospheric mantle beneath a craton and a rift, as well as their implication on its geodynamical behaviour. I have analysed the microstructures, the CPOs, and the hydrogen content of mantle xenoliths from the Kaapvaal craton, and two sets of xenoliths from different localities along the East African Rift (North Tanzanian Divergence and SE Ethiopia).The coarse-granular microstructures and the well-defined CPOs in Kaapvaal peridotites suggest a deformation followed by a long quiescence time. Orthorhombic olivine CPOs predominates, but axial-[100] and axial-[010] are also measured. Cratonic peridotites record multiple metasomatic episodes, leading to a significant compositional heterogeneity, which cannot be imaged by seismic studies. Olivine hydrogen contents are variable, but tend to increase until 150 km depth, reaching up to 50 ppm wt. H2O. The deeper samples are almost dry. Piston-cylinder experiments on hydrogen diffusion between a volatile-rich kimberlitic melt and forsterite suggest that the presence of CO2 in the system could significantly decrease water fugacity and thus forsterite hydration. These experimental results indicate that the hydrogen contents measured in olivine were acquired during a metasomatic event rather than during xenolith extraction by kimberlites. However, this metasomatism was not followed by remobilization of the cratonic root.In the North Tanzanian Divergence, localities within the rift axis and the volcanic transverse belt (Lashaine and Olmani) show significant differences in microstructures and olivine CPO patterns. In Lashaine, coarse-granular microstructures and orthorhombic to axial-[100] CPO patterns in olivine can be explained by transpressional deformation during the formation of the Mozambique belt, or by the occurrence of a remnant of a cratonic domain embedded within the Mozambique belt. Within the rift axis, porphyroclastic to mylonitic microstructures suggest a recent rift-related deformation accompanied by syn-kinematic melt-rock reactions, and followed by variable annealing. The strong heterogeneity in microstructures and olivine CPO suggests that this deformation was acquired during multiple tectonic events probably linked to episodic magma percolation, separated by quiescence episodes. The axial-[100] patterns in olivine and the oblique fast directions reported by SKS studies are coherent with transtensional deformation within the lithospheric mantle beneath the rift.The peridotites from SE Ethiopia are less recrystallized than the rift-axis Tanzanian peridotites, displaying coarse-porphyroclastic microstructures. Microstructures and orthorhombic CPOs in olivine suggest syn- to post-metasomatic deformation. S-waves polarization anisotropies calculated for these samples cannot explain alone the delay times reported by SKS studies in this part of the East-African Rift.
Les travaux réalisés durant cette thèse apportent de nouvelles contraintes sur les relations entre déformation, hydratation et percolation de fluides et/ou de magmas dans le manteau subcontinental sous un craton et sous un rift, et leurs implications sur son comportement rhéologique. Il repose sur l'analyse des microstructures, des OPRs et des teneurs en hydrogène de xénolites mantelliques du craton du Kaapvaal, et sur deux séries de xénolites provenant de différentes localités le long du rift Est-Africain (Divergence Nord Tanzanienne et SE de l'Ethiopie). Les microstructures granulaires à gros grains et les OPRs bien définies des péridotites du craton du Kaapvaal sont cohérentes avec un épisode de déformation suivi d'une longue période de quiescence. Les OPRs de l'olivine sont majoritairement à symétrie orthorhombique, mais des symétries axiale-[100] et axiale-[010] sont aussi mesurées. Les péridotites cratoniques enregistrent de multiples épisodes métasomatiques, ayant entraîné une hétérogénéité de compositions à petite échelle ne pouvant être détectée par les études sismiques. Les teneurs en hydrogène mesurées dans l'olivine sont variables, mais ont tendance à augmenter jusqu'à 150 km de profondeur, atteignant alors jusqu'à 50 ppm wt. H2O. En dessous de cette profondeur, les échantillons montrent des teneurs en hydrogène très faibles. Les expériences réalisées en piston-cylindre sur la diffusion de l'hydrogène issue d'un liquide kimberlitique vers de la forstérite suggèrent que la fugacité en eau pourrait fortement être diminuée par la présence de CO2, empêchant l'hydratation de l'olivine durant extraction des xénolites par les kimberlites. Ces résultats expérimentaux suggèrent que les teneurs en hydrogène dans l'olivine des péridotites du craton du Kaapvaal ont été acquises durant un épisode métasomatique en profondeur et non pendant leur extraction par les kimberlites. Ces teneurs n'ont toutefois pas à ce jour entraîné de remobilisation de la racine cratonique. Enfin, le calcul des propriétés sismiques des péridotites cratoniques révèle que les anisotropies générées par les OPRs de ces échantillons sont suffisantes pour expliquer les anisotropies mesurées par les ondes SKS et les ondes de surface.Les xénolites de la Divergence Nord-Tanzanienne, montrent des variations significatives de microstructures et d'OPR de l'olivine entre les péridotites des localités dans l'axe du rift et celles de la chaîne volcanique transverse (Lashaine et Olmani). A Lashaine, les microstructures granulaires à gros grains et les OPRs de type orthorhombique et axial-[010] peuvent être expliquée par une déformation en transpression liée à la formation de la chaîne Mozambique ou par la présence d'une relique d'un domaine cratonique à l'intérieur de la chaîne Mozambique. Dans l'axe du rift, les microstructures porphyroclastiques à mylonitiques suggèrent une déformation plus récente, accompagnée de réactions magma-roche sous des conditions proches du solidus, suivie d'un recuit variable. L'hétérogénéité des microstructures enregistrées par les échantillons du rift suggère de multiples épisodes de déformation localisée, probablement liés à l'injection percolation épisodique de magmas, espacés de périodes d'accalmie. Les OPRs de l'olivine de type axial-[100] et l'orientation des directions de polarisation des ondes SKS suggère que le rift s'est formé en régime de transtension Les péridotites du Sud-Est de l’Éthiopie présentent des microstructures porphyroclastiques à gros grains moins recristallisées qu'en Tanzanie. Les microstructures et les OPRs principalement de type orthorhombique suggèrent une déformation syn- à post-métasomatisme. Les anisotropies de polarisation des ondes S calculées pour ces échantillons sont insuffisantes pour expliquer à elles seules les déphasages des ondes SKS dans cette partie du rift.
https://tel.archives-ouvertes.fr/tel-01684759

Droits : info:eu-repo/semantics/OpenAccess
NNT : 2014MON20139
tel-01684759
https://tel.archives-ouvertes.fr/tel-01684759
https://tel.archives-ouvertes.fr/tel-01684759/document
https://tel.archives-ouvertes.fr/tel-01684759/file/43443_BAPTISTE_2014_archivage_cor.pdf

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
Arenal volcano is nearly unique among arc volcanoes with its 42 year long (1968–2010) continuous, small-scale activity erupting compositionally monotonous basaltic andesites that also dominate the entire, ~7000 year long, eruptive history. Only mineral zoning records reveal that basaltic andesites are the result of complex, open-system processes deriving minerals from a variety of crystallization environments and including the episodic injections of basalt. The condition of the mafic input as well as the generation of crystal-rich basaltic andesites of the recent, 1968–2010, and earlier eruptions were addressed by an experimental study at 200 MPa, 900–1,050 °C, oxidizing and fluid-saturated conditions with various fluid compositions [H2O/(H2O + CO2) = 0.3–1]. Phase equilibria were determined using a phenocryst-poor (~3 vol%) Arenal-like basalt (50.5−wt% SiO2) from a nearby scoria cone containing olivine (Fo92), plagioclase (An86), clinopyroxene (Mg# = 82) and magnetite (Xulvö = 0.13). Experimental melts generally reproduce observed compositional trends among Arenal samples. Small differences between experimental melts and natural rocks can be explained by open-system processes. At low pressure (200 MPa), the mineral assemblage as well as the mineral compositions of the natural basalt were reproduced at 1,000 °C and high water activity. The residual melt at these conditions is basaltic andesitic (55 wt% SiO2) with 5 wt% H2O. The evolution to more evolved magmas observed at Arenal occurred under fluid-saturated conditions but variable fluid compositions. At 1,000 °C and 200 MPa, a decrease of water content by approximately 1 wt% induces significant changes of the mineral assemblage from olivine + clinopyroxene + plagioclase (5 wt% H2O in the melt) to clinopyroxene + plagioclase + orthopyroxene (4 wt% H2O in the melt). Both assemblages are observed in crystal-rich basalt (15 vol%) and basaltic andesites. Experimental data indicate that the lack of orthopyroxene and the presence of amphibole, also observed in basaltic andesitic tephra units, is due to crystallization at nearly water-saturated conditions and temperatures lower than 950 °C. The enigmatic two compositional groups previously known as low- and high-Al2O3 samples at Arenal volcano may be explained by low- and high-pressure crystallization, respectively. Using high-Al as signal of deeper crystallization, first magmas of the 1968–2010 eruption evolved deep in the crust and ascent was relatively fast leaving little time for significant compositional overprint by shallower level crystallization.
ISSN: 0010-7999

hal-01115717
https://hal.archives-ouvertes.fr/hal-01115717
DOI : 10.1007/s00410-014-1040-4

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Cobalt-bearing pyrite (0.5-2.0 wt.% Co) is abnormally abundant (up to 35 vol.% of the total volume of the sulfide phase) in some eastern Pyrenean peridotite massifs, compared to pieces of subcontinental mantle studied so far for sulfides. Pyrite occurs as vermicular intergrowths inside pentlandite and/or chalcopyrite or as coarser, blocky grains in the intergranular pores of host peridotites. Those different pyrites are characterized by different platinum-group element systematics (measured by laser ablation microprobe and ICP-MS). Vermicular pyrite intergrown with pentlandite displays Os-, Ir-, Ru- and Rh-enriched chondrite normalized PGE patterns of Monosulfide solid solution (Mss). In contrast, coarse-grained intergranular ("blocky") pyrites, are PGE-poor. Chalcophile trace elements (i.e. Zn, Pb, Ag, Au) that are not usually concentrated in mantle-derived sulfides were commonly detected. By contrast, selenium contents are generally low, yielding thus pyrite with high S/Se ratio (> 10(5)), consistent with a sedimentary sulfur source. Pyrite microtextures and chalcophile trace element contents support a process of assimilation of crustal sulfur from the metamorphosed sedimentary country rocks. These latter generated highly reactive CO2-S fluids, which were injected into structural discontinuities of the lherzolitic bodies. Sulfur has reacted at T = 300-550A degrees C with pre-existing, mantle-derived, metal-rich sulfide assemblages (pentlandite-chalcopyrite). Addition of crustal sulfur did produce Mss which, on cooling, exsolved the Os-rich pyrite in addition to pentlandite. The coarse-grained pyrite types have crystallized directly from S-rich fluids.
ISSN: 0010-7999

hal-00617425
https://hal.archives-ouvertes.fr/hal-00617425
DOI : 10.1007/s00710-010-0138-2

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Numerical programs for simulating flow and reactive transport in porous media are essential tools for predicting reservoir properties changes triggered by CO2 underground injection. At reservoir scale, meshed models in which equations are solved assuming that constant macroscopic properties can be defined in each cells, are widely used. However, the parameterization of the dissolution-precipitation problem and of the feedback effects of these processes on the flow field is still challenging. The problem arises from the mismatch between the scales at which averaged parameters are defined in the meshed model and the scale at which chemical reactions occur and modify the pore network geometry. In this paper we investigate the links between the dissolution mechanisms that control the porosity changes and the related changes of the reactive surface area and of the permeability. First, the reactive surface area is computed from X-ray microtomography data obtained before and after a set of dissolution experiments of pure calcite rock samples using distinctly different brine-CO2 mixtures characterizing homogeneous to heterogeneous dissolution regimes. The results are used to validate the power law empirical model relating the reactive surface area to porosity proposed by Luquot and Gauze (2009). Second, we investigate the spatial distribution of the effective hydraulic radius and of the tortuosity, two structural parameters that control permeability, in order to explain the different porosity-permeability relationships observed for heterogeneous and homogeneous dissolution regimes. It is shown that the increase of permeability is due to the decrease of the tortuosity for homogeneous dissolution, whereas it is due to the combination of tortuosity decrease and hydraulic radius increase for heterogeneous dissolution. For the intermediate dissolution regime, identified to be the optimal regime for increasing permeability with small changes in porosity, the increase of permeability results from a large increase in the mean effective hydraulic radius of the sample.
ISSN: 0169-7722

hal-00617671
https://hal.archives-ouvertes.fr/hal-00617671
DOI : 10.1016/j.jconhyd.2010.07.004