Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either "artificially", or by natural extractives.
ISSN: 0043-7719

hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242/document
https://hal.archives-ouvertes.fr/hal-00804242/file/Anisotropy_wood_variational_properties_Bremaud_al_2011.pdf
DOI : 10.1007/s00226-010-0393-8

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Few studies have investigated the influence of environmental conditions on the within-treevariation in Eucalyptus wood traits. The genotype and environment effects and their interactionsinfluence the wood properties. Their evaluations are crucial to estimate the genotype values andto select with efficiency. Thus, the aim of this study was to better understand the effect ofground slope and wind speed on the spatial variation of basic density (ρ), stiffness (MOE) andmicrofibril angle (MFA) of Eucalyptus wood. Wood discs cut along the trunk were sampledfrom 150 six-year-old Eucalyptus grandis x E. urophylla hybrids growing in 3 contrastinggrowing conditions influenced by ground slope and wind regime. Near Infrared (NIR)calibrations previously developed for ρ, MOE and MFA were used to predict in our discs. 2-Dplots presenting the spatial variation of predicted wood traits were compared. The higher theground slope, the greater the magnitude of radial variation in ρ, principally in the medium zoneof the trunk. The spatial variation of wood stiffness seems to be sensitive to two environmentalconditions. The MFA radial decreases were more pronounced where the wind speed was higher.At the base and top of the trees, however, there was no significant effect of growing conditionson the radial variation of the wood properties considered here.
ISSN: 0931-1890

hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896/document
https://hal.archives-ouvertes.fr/hal-01451896/file/Art_Gril_al_Spatial_variation_wood_density_2016.pdf
DOI : 10.1007/s00468-015-1327-8

Éditeur(s) : HAL CCSD Fayard/Arthème
Résumé : La biomécanique des plantes est née d'une approche interdisciplinaire. Elle regroupe ainsi des biologistes, des forestiers ou des agronomes, et des mécaniciens (des matériaux et des structures et plus récemment des fluides). Elle s'intéresse à la façon dont les plantes se portent et croissent. En particulier comment les plantes terrestres croissent en hauteur " contre " la gravité et dans le vent ; mais aussi comment les plantes aquatiques et les algues se développent dans les courants.
Aux Origines des Plantes

hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935/document
https://hal.archives-ouvertes.fr/hal-00795935/file/BiomA_canique_plantes_Fournier_Moulia_Gril.pdf

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
In the dense tropical rainforest understorey, saplings exhibit different growth strategies aiming at reaching light levels better fitting their ecology. Investing mainly in height growth, at the expense of their width, a lot are close to mechanical instability. Tachigali melinonii, a long living heliophilic tree species, is frequently observed to be extremely slender and supported by neighbours. Such observations suggest an active growth control through the perception of mechanical environment. * Mechanical environment or light availability, which one is the most influent on growth and slenderness (H/D)? To test this question, we recorded growth of control and staked saplings of two species with contrasting habits and ecology: T. melinonii, and Dicorynia guianensis, along a natural light gradient. * Dicorynia, the more stable, responded more clearly to the staking treatment, showing slenderness increase when light is available, whereas for Tachigali, only light availability governed growth. * For Tachigali, growth allocation is mainly governed by light availability and ontogeny, whereas Dicorynia is probably similar to the average tree strategy, using the thigmomorphogenetic physiological process to control its stability.
ISSN: 1286-4560

hal-00534019
https://hal.archives-ouvertes.fr/hal-00534019
DOI : 10.1051/forest/2009104

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
This study aims at better understanding the respective influences of specific gravity (γ), microfibril angle (MFA), and cell-wall matrix polymers on viscoelastic vibrational properties of wood in axial direction. The wide variations of properties between normal wood (NW) and compression wood (CW) are in focus. Three young bent trees (Picea abies, Pinus sylvestris and Pinus pinaster) that recovered verticality were sampled. Several observed differences between NW and CW were highly significant in terms of anatomical, physical (γ, shrinkage, CIELab colorimetry), mechanical (compressive strength), and vibrational properties. Specific dynamic modulus of elasticity (E'/γ) decreases with increasing MFA, and Young's modulus (E') can be satisfactorily explained by γ and MFA. Apparently, the type of the cell wall polymer matrix is not influential in this regard. The damping coefficient (tanδ) does not depend solely on MFA of NW and CW. The tanδ - E'/γ relationship evidences that, at equivalent E'/γ, the tanδ of CW is approx. 34% lower than that of NW. This observation is ascribed to the more condensed nature of CW lignins, and this is discussed in the context of previous findings in other hygrothermal and time/frequency domains. It is proposed that the lignin structure and the amount and type of extractives, which are both different in various species, are partly responsible for taxonomy-related damping characteristics.
ISSN: 0018-3830

hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062/document
https://hal.archives-ouvertes.fr/hal-00808062/file/Changes_viscoelastic_vibrational_Bremaud_al.pdf
DOI : 10.1515/hf-2011-0186

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A feasibility study of glulam was carried out in French Guiana using local wood species. The aim was to determine gluing parameters affording satisfactory behaviour to manufactured glulam in a tropical climate. Three abundant wood species, with special properties, were selected for the study and Resorcinol-Phenol-Formaldehyde resin was used for bonding. Three industrial parameters were considered: adhesive spread rate, closed assembly time and gluing pressure. Delamination and shearing tests were carried outin accordance with European Standards. The tests revealed the influence of wood properties and manufacturing parameters on joint resistance. In fact, the results showed that specific gravity and the shrinkage coefficientgreatly influenced the gluing step. Indeed, wood with a medium specific gravity needed more adhesive and more pressure than wood with a high specific gravity. In addition, planning and lamella thicknesswere found to affect glue joint resistance.
ISSN: 0018-3768

hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933/document
https://hal.archives-ouvertes.fr/hal-00856933/file/Feasibility_glued_laminated_timber_Bourreau_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
In order to progress in the understanding of mechanical stress generation, the mesoporosity of the cell wall and its changes during maturation of poplar (Populus deltoides x P. nigra) tension wood (TW) and opposite wood (OW) were measured by nitrogen adsorption–desorption. Variations in the thickness of the gelatinous layer (G-layer) were also measured to clarify whether the mesoporosity change simultaneously with the deposition of the G-layer in TW. Results show that mesoporous structures of TW and OW were very similar in early development stages before the deposition of G-layers. With the formation of the S2 layer in OW and the G-layer in TW, the mesopore volume decreased steeply before lignification. However, in TW only, the decrease in mesopore volume occurred together with the pore shape change and a progressive increase in pore size. The different patterns observed in TW revealed that pores from G-layers appear with a different shape compared to those of the compound middle lamella, and their size increases duringthe maturation process until stabilising in mature wood. This observation strongly supports the hypothesis of the swelling of the G-layer matrix during maturation as the origin of maturation stress in poplar tension wood.
ISSN: 0028-646X

hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834/document
https://hal.archives-ouvertes.fr/hal-01081834/file/Chang_al_Mesoporosity_changes_New-Phyto._2015.pdf
DOI : 10.1111/nph.13126

Éditeur(s) : HAL CCSD
Résumé : International audience
The hierarchical architecture of biopolymers induces remarkable behaviour. Wood mechanical properties mainly originate from the organization of wood tissue and interactions of cellwall components. The respective contribution on components inside those networks occurs at nanometric scale and still challenging to investigate in-situ. X-ray scattering techniques are now used as a routine technique to investigate internal organization of material components. For that purpose large-scale synchrotron facilities like ESRF offer leading X-ray sources capabilities (large energy range, high brilliance, high intensity, dedicated setups). ESRF's ID13 beamline serves high spacial resolution scanning setups to expertise in elastic scattering of monochromatic X-rays. Since analytical description of the scattering signal of cellulose have been well describe wood material benefit wide range of exposure conditions and sample environment. During this conference, we will present our achievements based on transverse sections of poplar specimens exposed to micrometric beam (1.2 μm side, 12.6 keV energy) to reveal crystalline cellulose distribution within wood tissue and to nanometric beam (100 nm side, 12 6 keV energy) to map the evolution of cellulose orientation within double cell wall over combined Wide-Angle (WAXS) and Small-Angle (SAXS) X-ray Scattering configuration. Within those setups hygrometric sample environment and stretching solicitations will be approached based on-going developments.
COST FP0802 Workshop 'Micro Characterisation of Wood Material'
Edimbourg, United Kingdom

hal-01113298
https://hal.archives-ouvertes.fr/hal-01113298

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Radial trends of vibrational properties, including the specific dynamic modulus (E'/r) and damping coefficient (tand), were investigated for 3 tropical rainforest hardwood species, Simarouba amara, Carapa procera and Symphonia globulifera by free-free flexural vibration test. The microfibril angle (MFA) was estimated through X-Ray diffraction. Consistent patterns of radial variations were observed for all studied properties. E'/r was found to decrease from pith to bark, which is strongly related to the increasing pith-bark trend of MFA. The variation of tand along the radius can be partly explained by MFA, and partly by the gradient of extractives due to heartwood formation. The coupling effect of MFA and extractives could be separated through the analysis of log(tand) - log(E'/r) diagram. For the studied species, the extractive content putatively associated to heartwood formation generally tends to decrease the wood damping coefficient. However, this weakening effect of extractives was not observed for inner part of the heartwood, suggesting the mechanical action of extractives was reduced during their chemical ageing.
ISSN: 1435-0211

hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055/document
https://hal.archives-ouvertes.fr/hal-00797055/file/Radial_variations_vibrational_Zhang_al.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
The main biological function of reaction wood is to act as “muscle” for trees, enabling them to control their posture and right stems when they are permanently disturbed from their set-point inclination by gravity or winds. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called “maturation strains”. Moreover, this function is basically performed through the asymmetric formation of wood (in quantity or quality) around the tree circumference. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity, as an asymmetric force associated to maturation strains creates a bending moment (i.e. one side of the stem “pulls” the other one). We will discuss the traits (cross sectional size and shape, wood features as G fibers or microfibril angle, eccentric growth even in usual or extreme cases as buttresses, total biomass growth and height of center of mass, stem lean and set-point angle) involved to understand how the posture control works. We will give simple formulas to estimate a “muscle efficiency” from biomechanical modeling. We will give practical methods to estimate all the involved traits, especially maturation strains from direct and indirect measurements, in peripheral functional wood or by retrospective dendrochronological analysis. Then, we will illustrate how tree stem tropisms and especially gravitropism, widely studied by physiologists, are key processes in natural ecosystems, through practical examples from tropical rainforest tree communities and regeneration of European mixed beech forests. Using the previous definition of postural control efficiency, we will show that the cross section size is rapidly a limiting factor, opposing the extreme strategies of flexible small stems, which bend easily but also right themselves quickly, to stiff big stems. Lastly, as wood in living trees ensures general storage, defence, vascular and skeletal functions, we will ask general questions about synergies and trade-offs between posture control and other functions.
Botany 2014 : new frontiers in botany
Boise, United States

hal-01627031
https://hal.archives-ouvertes.fr/hal-01627031

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Extractives that provide natural resistance to Bagassa guianensis Aubl. heartwood were examined. Soil-bed tests showed that the B. guianensis heartwood resistance was significantly reduced after ethyl acetate extraction, whereas methanol and especially water extractions improved the resistance. The ethyl acetate extract was submitted to a bioguided fractionation, and fractions were tested against one wood-destroying fungal strain (Pycnoporus sanguineus) and two human pathogenic fungal strains (Candida glabrata (yeast) and Trichophyton rubrum (filamentous dermatophyte)). Fraction F7, which exhibited the strongest antifungal activity, was subsequently fractionated by high performance liquid chromatography (HPLC). Six previously described compounds were isolated. Although the two moracins, 6-O-methyl-moracin N (3) and moracin N (4) were the most active against fungal strains with MIC values between 4 and 16 μg ml−1, the isolated compounds showed less or equivalent antifungal activity than the initial fraction. Possible synergism between compounds 3 and 4 and other secondary metabolites have been hypothesized. Our study demonstrated that this extract as a whole might be used as a wood preservation or antimycotic product.
International Biodeterioration and Biodegradation

hal-00694532
https://hal.archives-ouvertes.fr/hal-00694532
DOI : 10.1016/j.ibiod.2011.10.016

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0

Éditeur(s) : HAL CCSD
Résumé : International audience
Some morphological and biochemical taxonomic markers are also affecting factors of dynamic mechanical properties of wood. Thus, could these properties reflect the classification/phylogeny of taxa? This work is a first insight into this question. It relied on the gathering (through experimental campaigns and exhaustive literature review) of a large database on the viscoelastic (i.e. including damping) vibrational properties of 445 woody species. relationship between damping was confirmed at a wide interspecific scale, but described no more than 40% of not in a way that could be easily related to the phylogenetic tree. Damping was a bit more -Papilionoideae and, to a lesser extent, Lauraceae, Cupressaceae and Moraceae) damping than average, independently While for some other families no clear characteristics could be observed at least with the present number of represented species. In the future, increasing the amount of data and compiling anatomical and chemical markers / affecting factors will allow further analysis at sub-family levels, and a better understanding of this wide topic.
6th Plant Biomechanics Conference PBM09
Cayenne, French Guiana

hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398/document
https://hal.archives-ouvertes.fr/hal-00808398/file/Mechanical_damping_wood_Bremaud_al.pdf

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
International audience
The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three-dimensional strains were measured at different parts of the trunk base. Risks of failure were greater on the buttress sides, where shear and tangential stresses are greater, not on the ridges, in spite of high longitudinal (parallel to the grain) stresses. A simple beam model, computed from the second moment of area of digitized cross sections, is consistent with longitudinal strain variations but cannot predict accurately variations with height. Patterns of longitudinal strain variation along ridges are very different in the two individuals, owing to a pronounced lateral curvature in one specimen. The constant stress hypothesis is discussed based on these results. Without chronological data during the development of the tree, it cannot be proved that buttress formation is activated by stress or strain.
ISSN: 0002-9122

hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155/document
https://hal.archives-ouvertes.fr/hal-01032155/file/Biomechanics_buttressed_trees_Clair_al_2003.pdf
DOI : 10.3732/ajb.90.9.1349

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Functional ecology has long considered the support function as important, but its biomechanical complexity is only just being elucidated. We show here that it can be described on the basis of four biomechanical traits, two safety traits against winds (SW) and self-buckling (SB), and two motricity traits involved in sustaining an upright position, tropic motion velocity (MV) and posture control (PC). All these traits are integrated at the tree scale, combining tree size and shape together with wood properties. The assumption of trait constancy has been used to derive allometric scaling laws, but it was more recently found that observing their variations among environments and functional groups, or during ontogeny, provides more insights into adaptive syndromes of tree shape and wood properties. However, over-simplified expressions have often been used, possibly concealing key adaptive drivers. An extreme case of over-simplification is the use of wood basic density as a proxy for safety. Actually, since wood density is involved in stiffness, loads and construction costs, the impact of its variations on safety is non-trivial. Moreover, other wood features, especially the microfibril angle (MFA), are also involved. Furthermore, wood is not only stiff and strong, but it also acts as a motor for MV and PC. The relevant wood trait for that is maturation strain asymmetry. Maturation strains vary with cell wall characteristics such as MFA, rather than with wood density. Finally, the need for further studies about the ecological relevance of branching patterns, motricity traits and growth responses to mechanical loads is discussed.
ISSN: 0022-0957

hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904/document
https://hal.archives-ouvertes.fr/hal-00909904/file/Integrative_biomechanics_for_tree_Fournier_al.pdf
DOI : 10.1093/jxb/ert279

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Studies on the periodicity of wood formation provide essential data on tree age and factors related to the control of tree growth. The aim of this work was to investigate the cambial phenology and its relation with leaf phenology and climatic seasonality in two tropical rainforest species belonging to the genus Parkia known for having a contrasted leaf phenology. From wood samples collected at 15 day intervals from April 2009 to February 2012 in five trees of both species, we quantified cambial activity by counting layers of cells in cambial zone, enlarging cells zone and wall thickening cells zone from wood prepared anatomical micro sections. In the same time, we observed leaf shedding behaviors in the crown of the studied trees. In both species, cambial activity was significantly reduced during leafless period. However, the cambial activity of P. velutina was not affected by seasonality while in P. nitida, we found a significant positive effect of the dry season on cambial activity. This diminution of activity associated to leaf shedding occurred annually during the dry season in P. nitida whereas the trees were not synchronous in time for P. velutina. On the contrary that is often admitted, the rest cambial period can be independent of environmental restriction such as dry season. Leaf phenology remains the best proxy to estimate cambial activity.
ISSN: 0931-1890

hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166/document
https://hal.archives-ouvertes.fr/hal-01135166/file/Art_Morel_al_Seasonal_variations_phenological_traits_2015.pdf
DOI : 10.1007/s00468-015-1177-4