Éditeur(s) : HAL CCSD
Résumé : In Taiwan , the subduction of the Chinese continental margin under the Luzon arc results in the progressive growth of an active orogenic wedge. It is one of the best places to study the complex relationships that occurs between the tectonic processes controlling deformation (plate rheology and kinematics, metamorphism and magmatism) and surface processes (erosion and sedimentation). In order to study the kinematics of the present day convergence of Philippine Sea plate to the Asian continent around Taiwan, we perform 2D and 3D sandbox modeling and we analyzed the models with PIV (Particle Image Velocimetry) software. In 2D experiments, a model Coulomb wedge is submitted to erosion and sedimentation under topography and flux steady state conditions. The 3D experiments are mainly used to study the escape tectonics occurring in the middle west and southwest Taiwan. A wedge shaped indenter and a basement relief were used to simulate the mechanical plate boundary between Philippine Sea plate and Eurasia plate and the basement topography to the west of Taiwan respectively. We examine the exhumation patterns, the mode of fault propagation and displacement patterns by strain partitioning of vertical vs. horizontal displacement and convergent parallel vs. orogen parallel components. The preliminary conclusions are: 1. The interactions between tectonics, erosion and sedimentation control geometry and kinematics of the doubly vergent transpressional orogen. 2. Exhumation processes are controlled by the balance between erosion, frontal accretion and underplating in different structural domains of the wedge. 3. Retrowedge erosion favorites backfolding and backthrusting, induces flower structures and fan shaped cleavage distribution. 4. Sedimentation promotes underplating and out-of sequences thrusting. 5. Continental subduction or subduction of topographic highs will enhance underthrusting/underplating, thick-skin tectonics and inversion of sedimentary basin.
Bolletino di Geofisica teorica ed applicata

hal-00411133
https://hal.archives-ouvertes.fr/hal-00411133

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Iron is an essential micronutrient involved in many biological processes and is often limiting for primary production in large regions of the World Ocean. Metagenomic and physiological studies have identified clades or ecotypes of marine phytoplankton that are specialized in iron depleted ecological niches. Although less studied, eukaryotic picophytoplankton does contribute significantly to primary production and carbon transfer to higher trophic levels. In particular, metagenomic studies of the green picoalga Ostreococcus have revealed the occurrence of two main clades distributed along coast-offshore gradients, suggesting niche partitioning in different nutrient regimes. Here, we present a study of the response to iron limitation of four Ostreococcus strains isolated from contrasted environments. Whereas the strains isolated in nutrient-rich waters showed high iron requirements, the oceanic strains could cope with lower iron concentrations. The RCC802 strain, in particular, was able to maintain high growth rate at low iron levels. Together physiological and transcriptomic data indicate that the competitiveness of RCC802 under iron limitation is related to a lowering of iron needs though a reduction of the photosynthetic machinery and of protein content, rather than to cell size reduction. Our results overall suggest that iron is one of the factors driving the differentiation of physiologically specialized Ostreococcus strains in the ocean.
ISSN: 2045-2322

Droits : http://creativecommons.org/licenses/by/
hal-01502140
http://hal.upmc.fr/hal-01502140
http://hal.upmc.fr/hal-01502140/document
http://hal.upmc.fr/hal-01502140/file/acclimation.pdf
DOI : 10.1038/s41598-017-00216-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In oblique collision settings, parallel and perpendicular components of the relative plate motion can be partitioned into different structures of deformation and may be localized close to the plate boundary, or distributed on a wider region. In the Southern Alps of New Zealand, it has been proposed that one-third of the regional convergence is distributed in a broad area along the Southern Alps orogenic wedge. To better document and understand the regional dynamics of such systems, reliable markers of the horizontal tectonic motion over geological time scales are needed. River networks are able to record a large amount of distributed strain and they can thus be used to reconstruct the mode and rate of distribution away from major active structures. To explore the controls on river resilience to deformation, we develop an experimental model to investigate river pattern evolution over a doubly-vergent orogenic wedge growing in a context of oblique convergence. We use a rainfall system to activate erosion, sediment transport and river development on the model surface. At the end of the experiment, the drainage network is statistically rotated clockwise, confirming that rivers can record the distribution of motion along the wedge. Image analysis of channel time-space evolution shows how the fault-parallel and fault-perpendicular components of motion decrease toward the fault and impose rotation to the main trunk valleys. However, rivers do not record the whole imposed rotation rate, which suggest that the natural lateral channel dynamics can alter the capacity of rivers to act as passive markers of deformation.
ISSN: 0040-1951

hal-01467564
https://hal.archives-ouvertes.fr/hal-01467564
DOI : 10.1016/j.tecto.2016.04.016

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The lateral variation of the mechanical properties of continental lithosphere is an important factor controlling the localization of deformation and thus the deformation history and geometry of intraplate mountain belts. A series of three-layer lithospheric-scale analog models, with a strong domain (SD) embedded at various depths, are presented to investigate the development of topography and deformation patterns by having lateral heterogeneities within a weak continental lithosphere. The experiments, performed at a constant velocity and under normal gravity, indicate that the presence or absence of the SD controls whether deformation is localized or distributed at a lithospheric scale. Deformation and topography localize above the edges of the SD, while the SD region itself is characterized by minor amounts of surficial deformation and topography. The depth of the SD (within the ductile crust, ductile mantle lithosphere, or both) controls the pattern of deformation and thus the topography. The presence of a SD in the ductile crust or in the mantle results in limited surficial topographic effects but large variations in the Moho topography. Strong Moho deflection occurs when the SD is in the ductile crust, while the Moho remains almost flat when the SD is in the mantle. When the SD occupies the ductile lithosphere, the SD is tilted. These analog experiments provide insights into intraplate strain localization and could in particular explain the topography around the Tarim Basin, a lithospheric-scale heterogeneity north of the India-Asia collision zone.
ISSN: 0278-7407

hal-01172472
https://hal.archives-ouvertes.fr/hal-01172472
DOI : 10.1002/2014TC003756

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
TEM Study of Heavitree quartzite deformed at high temperatures and a pressure of 1.5 GPa with three different preparations: water-added, vacuum dried, and sodium doped show a wide range of dislocation microstructure. The vacuum dried sample has a very heterogeneous dislocation distribution varying from almost no dislocations to very high densities. Dislocation nucleation occurs by cross-slip mechanisms, such as Frank-Read sources and Orowan loops around hard inclusions. Shear bands develop in the basal plane composed of two closely spaced shear planes. Dislocations have straight segments and they are aligned along directions of dense packing, suggesting strong Peierls stress control due to the crystal structure. No voids, bubbles or dislocation walls where observed in the vacuum dried sample. The sodium-doped sample had a homogeneous high dislocation density. The water-added sample has a significantly lower, relatively uniform dislocation density. Bubbles associated with dislocations are seen in every grain. Dislocations were either present in loops around bubbles or as straight dislocations with small bubbles spaced along the dislocation line. Some of the long straight dislocations are aligned parallel to the c-axis. Sub-grains where very frequent, sometimes form cells of about 2 p,m in diameter with straight edges. Analysis of dislocations show 1/3 < a > and [c] dislocations in sub-grain walls and free 1/3 < a > dislocations on prism planes. There is clear evidence for dislocation climb with sub-grain walls, dislocation cells, dislocation junctions and dislocation debris of small loops. The major difference between vacuum dried and water-added samples are the homogeneity of the microstructure and evidence for climb in the water-added sample. Glide is clearly difficult, with a high Peierls stress in the vacuum dried sample as shown by areas of very low and very high dislocation density and the crystallographic control of dislocation line direction. The sodium-doped sample indicates that nucleation was easy by the high homogenous dislocation density, but no climb recovery has taken place. The density is high and the dislocations are strongly interacting causing tangles; no evidence for crystallographic control can be observed at these levels of strain. The activation energy for creep in Heavitree quartzite decreases with inferred water content of the specimens form 185 kJ mol(-1) for vacuum dried to 151 for 0.4 wt% water-added samples. Analysis of diffusion data for oxygen under hydrothermal conditions and inferred diffusion data for the hydrogarnet defect and dislocation velocity suggests activation energies for these processes are similar to the activation energy for the dislocation creep of Heavitree quartzite and other quartz aggregates. For data from the previously published experiments with the highest stress resolution there is a correlation between the A pre-factor in the power law creep equation and the activation energy for creep. It is speculated that the correlation may be due to variable hydrogarnet defect concentrations.
ISSN: 0031-9201

hal-00413112
https://hal.archives-ouvertes.fr/hal-00413112
DOI : 10.1016/j.pepi.2008.07.009

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Analysis of the microstructures in the km-scale mantle shear zone that separates the northern and the central parts of the Lanzo peridotite massif provides evidence of an evolution in time and space of deformation processes accommodating shearing in the shallow mantle within an extensional setting. This shear zone displays an asymmetric distribution of deformation facies. From south to north, gradual reorientation of the foliation of coarse porphyroclastic plagioclase-bearing peridotites is followed by development of protomylonites, mylonites, and mm-scale ultramylonite bands. A sharp grain size gradient marks the northern boundary. Early deformation under near-solidus conditions in the south is recorded by preservation of weakly deformed interstitial plagioclase and almost random clinopyroxene and plagioclase crystal orientations. Feedback between deformation and melt transport probably led to melt focusing and strain weakening in the shear zone. Overprint of melt-rock reaction microstructures by solid-state deformation and decrease in recrystallized grain size in the protomylonites and mylonites indicate continued deformation under decreasing temperature. Less enriched peridotite compositions and absence of ultramafic dykes or widespread melt-impregnation microstructures north of the shear zone and clinopyroxene and amphibole enrichment in the mylonites and ultramylonites suggest that the shear zone acted as both a thermal barrier and a high-permeability channel for late crystallizing fluids. These observations, together with chemical data indicating faster cooling of central Lanzo relative to the northern body, corroborate that this shear zone is a mantle detachment fault. All deformation facies have crystal preferred orientations consistent with deformation by dislocation creep with dominant activation of the (010)[100] and (100)[001] systems in olivine and orthopyroxene, respectively. Dynamic recrystallization produces dispersion of olivine CPO but not a change of dominant deformation mechanism. Evidence for activation of grain boundary sliding is limited to mm-scale ultramylonite bands, where solid-state reactions produced very fine grained polymineralic aggregates. Except for these latest stages of deformation, strain localization does not result from the microstructural evolution; the grain size decrease is a consequence of the need to deform a rock volume whose strength continuously increases because of decreasing temperature conditions. Strain localization in the intermediate levels thus essentially results from the more localizing behavior of both the deep, partially molten, and shallow parts of this extensional shear zone distribution.
ISSN: 1525-2027

hal-00644844
https://hal.archives-ouvertes.fr/hal-00644844
DOI : 10.1029/2011GC003627

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We present evidence that GPS velocity estimates of plate motions and fault slip rates agree to within uncertainties with geologic estimates during the most recent phase of the geologic evolution of the E Mediterranean region (post-Late Miocene). On this basis, we use the GPS differential velocities to estimate the timing of initiation of the principal structures in NW Turkey, the N Aegean Sea, and central Greece, including, the Marmara Sea, the Gulfs of Evia (GoE) and Corinth (GoC). and the Kephalonia Transform fault (KTF). We interpret these ages to indicate that the North Anatolian fault propagated across the N Aegean, opening the GoE and GoC and initiating the KTF, during the past 1-4 Ma. We further suggest that Aegean extension that was earlier more distributed across the Aegean Basin became focused on this new fault system allowing the southern Aegean and Peloponnisos to translate SW with little internal deformation, as observed today with GPS. This change in tectonic configuration may account for the clear geologic evidence for crustal thinning throughout the S Aegean in apparent contradiction with low present-day strain rates. We further show that the low present-day strain rate along the southern edge of the Aegean micro-plate requires substantial aseismic slip along the plate interface below Crete, consistent with the low level of historic, subduction-type earthquakes along this segment of the subduction zone.
ISSN: 0040-1951

hal-00512634
https://hal.archives-ouvertes.fr/hal-00512634
DOI : 10.1016/j.tecto.2009.05.027

Éditeur(s) : HAL CCSD BioMed Central
Résumé : International audience
BACKGROUND: Homologous recombination is the key process that generates genetic diversity and drives evolution. SPO11 protein triggers recombination by introducing DNA double stranded breaks at discreet areas of the genome called recombination hotspots. The hotspot locations are largely determined by the DNA binding specificity of the PRDM9 protein in human, mice and most other mammals. In budding yeast Saccharomyces cerevisae, which lacks a Prdm9 gene, meiotic breaks are formed opportunistically in the regions of accessible chromatin, primarily at gene promoters. The genome-wide distribution of hotspots in this organism can be altered by tethering Spo11 protein to Gal4 recognition sequences in the strain expressing Spo11 attached to the DNA binding domain of the Gal4 transcription factor. To establish whether similar re-targeting of meiotic breaks can be achieved in PRDM9-containing organisms we have generated a Gal4BD-Spo11 mouse that expresses SPO11 protein joined to the DNA binding domain of yeast Gal4. RESULTS: We have mapped the genome-wide distribution of the recombination initiation sites in the Gal4BD-Spo11 mice. More than two hundred of the hotspots in these mice were novel and were likely defined by Gal4BD, as the Gal4 consensus motif was clustered around the centers in these hotspots. Surprisingly, meiotic DNA breaks in the Gal4BD-Spo11 mice were significantly depleted near the ends of chromosomes. The effect is particularly striking at the pseudoautosomal region of the X and Y chromosomes -- normally the hottest region in the genome. CONCLUSIONS: Our data suggest that specific, yet-unidentified factors influence the initiation of meiotic recombination at subtelomeric chromosomal regions.
ISSN: 1471-2164

inserm-00849779
http://www.hal.inserm.fr/inserm-00849779
http://www.hal.inserm.fr/inserm-00849779/document
http://www.hal.inserm.fr/inserm-00849779/file/1471-2164-14-493.pdf
DOI : 10.1186/1471-2164-14-493

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
Here, the first description of an epsilon sulfur-oxidizing bacterium from sulfide-rich sediments of marine mangrove in Caribbean is reported. According to TEM, this new strain contains intracytoplasmic large internal sulfur granules as confirmed by EDXS analyses performed using ESEM. The sulfur distribution obtained for this sulfur-oxidizing bacterial strain allows to conclude that elemental sulfur is formed as an intermediate oxidation product and stored intracellularly. According to conventional SEM observations, bacterial cells are ovoid, extremely motile by lophotrichous flagella. Phylogenetic analyses based on the analysis of partial sequence of 16S rDNA confirm that such bacterial strain belongs to the Thiovulum cluster and could be a representative of a new species in this poorly studied genus of sulfur-oxidizing free-living bacteria. Thus, reduced sediment of marine mangrove represents sulfide-rich environment sustaining development of both gamma and epsilon sulfur-oxidizing Proteobacteria
ISSN: 0378-1097

hal-01682113
https://hal.univ-antilles.fr/hal-01682113
DOI : 10.1093/femsle/fnx172

Éditeur(s) : HAL CCSD Elsevier
Résumé : To contribute to the understanding of how opening-mode fractures (joints) form and open or close at depth in layered rocks, we present a 2D numerical study aiming to determine whether tensile stress can develop in pre-fractured elastic multilayers submitted to biaxial compressive strain conditions. First, we investigate the role of the elastic and geometrical properties of the layers on the development of tensile stress in models with five bonded layers and containing one open fracture in the central layer. Our results indicate that, in absence of elastic contrast (in Young's modulus) between the layers, no tensile stress develops in the models. However, when the fractured layer is stiffer than the two adjacent layers directly above and below, a lobe of horizontal tensile stress develops centered on the pre-existing fracture. The creation of this tensile stress is contingent upon the partial closing of the fracture. The levels of tensile stress and the thickness of the lobe of tensile stress increase logarithmically with an increase in the elastic contrast and are systematically larger for a larger Soft/Stiff ratio (ratio of the total thickness of the soft layers with the total thickness of the stiff layers). Second, we investigate the role of fracture interaction in the development of tensile stress in models containing a pair of open fractures. We observe that the levels of tensile stress in the region between the fractures are systematically higher than those observed in identical models containing a single fracture. This increase in tensile stress is very large for small elastic contrasts between the layers but diminishes when the elastic contrast increases. Furthermore, the spacing between the pre-existing fractures plays an important role in the stress distribution in the region between them. When the fracture spacing is equal to or lower than 1.15 times the height of the fractured layer for the experimental conditions chosen, the lobes of tensile stress centered on the fractures coalesce. This results in the formation of vast areas of tensile stress in models under remote compressive loading conditions. Such tensile areas are likely to allow the initiation and propagation of subsequent opening-mode fractures. The results obtained provide new insights into the formation of joints in layered rocks in compressive environments, with important consequences on fluid flow.
ISSN: 0040-1951

hal-00407576
https://hal.archives-ouvertes.fr/hal-00407576
DOI : 10.1016/j.tecto.2006.12.003

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
P>The Strait of Hormuz area is a transition zone between the continental collision of the Zagros (west) and the subduction of an oceanic part of the Arabian Plate beneath the Makran wedge (east). Geology and recent GPS measurements indicate that about 15 mm yr-1 of relative motion in N10 degrees E direction is accommodated by two major fault systems: (1) the NNW-trending Minab-Zendan-Palami (MZP) fault system that connects the Main Zagros Thrust (MZT) to the inner Makran thrust system and the Frontal subduction thrust and (2) the N-trending Sabzevaran-Kahnuj-Jiroft (SKJ) fault system that bounds the Jazmurian depression to the west. We use dense GPS measurements along four transects across these fault systems in order to determine the strains spatial distribution. The northern GPS transect confirms the total fault slip rates for both fault systems estimated by the tectonic analyses (about 10 and 7.3 mm yr-1 in N10 degrees direction across the MZP and SKJ fault systems, respectively). For both fault systems, the elastic deformation spreads over shear zones that are several tens of kilometres wide. However, transects located close to latitude 27 degrees N reveal a much narrower shear zone (similar to 10 km) for the MZP fault system. Moreover, we confirm that most of the present-day strain is transferred towards the frontal subduction thrust rather than towards the inner Makran thrusts. In order to complement this new GPS velocity field with spatially dense measurements, we processed a set of ERS radar images by the radar interferometry (InSAR) technique. We used both a 'stacking' and a 'persistant-scatterers' approach to differentiate the ground deformation signal which spatial gradient is expected to be very low, from the atmospheric signal. Results from these interferograms appear to be relatively in agreement with the GPS-determined strain distribution. Nevertheless, they confirm the absence of any superficial creep behaviour since no sharp discontinuity on interferometric phase can be noted on any interferogram. Finally, we use a purely kinematic 'block model' inversion process to calculate slip rates and locking depths for each fault system from our GPS measurements. These models suggest that the relative quiescence over the last 200 yr has certainly produced a slip deficit as high as 2 m. So, we may wonder if the MZP fault system is not late in the interseismic phase of its earthquake cycle.
ISSN: 0956-540X

hal-00429386
https://hal.archives-ouvertes.fr/hal-00429386
DOI : 10.1111/j.1365-246X.2009.04321.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We conducted triaxial compression experiments to investigate the effects of pressure, temperature and strain rate on the rheology of talc rocks. The tests were carried out at T from 25 to 860 degrees C, P from 0.1 to 300 MPa, and <(epsilon) over dot> from 0.3 to 30 x 10-5 s(-1). In addition to being very weak, there are other important differences between the mechanical behavior of talc and that of most other silicates. Deformation at all temperatures up to dehydration was accommodated by a combination of crystal plasticity, frictional sliding, and cataclasis. A transition from localized to distributed deformation occurred at P = 300 MPa and T = 400 degrees C, but this transition is ill-defined as both distributed and localized deformation were observed at P = 300 MPa and T = 600 degrees C. Unlike most silicates, both the coefficient of internal friction and the coefficient of (sliding) friction are very low and nearly equal to each other. Temperature enhances plastic deformation (kinking), and inter- and intra-granular microcracks are observed parallel to the (001) planes at all conditions. Voids are created by delamination along (001) planes at kink-band boundaries. Full crystal plasticity was not achieved under any of the conditions tested, i.e., the von Mises criterion was never satisfied. However, the strength of the aggregates remained much less than the confining pressure. These unusual properties are likely a manifestation of the pronounced mechanical anisotropy of talc at the grain scale. At T >= 750 degrees C dehydration is observed, but only along shear zones. These results suggest that feedbacks between deformation and reaction kinetics could control fluid flow in fault zones. The presence of talc can promote significant weakening and strain localization in the oceanic lithosphere, the subducting plate and the overlying mantle wedge. (c) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00492706
https://hal.archives-ouvertes.fr/hal-00492706
DOI : 10.1016/j.epsl.2008.02.004

Éditeur(s) : Amer Geophysical Union
Résumé : On November 21, 2004, a magnitude 6.3 earthquake occurred offshore, 10 km south of Les Saintes archipelago in Guadeloupe (French West Indies). There were more than 30000 aftershocks recorded in the following two years, most of them at shallow depth near the islands of the archipelago. The main shock and its main aftershock of February 14, 2005 (M-w = 5.8) ruptured a NE-dipping normal fault (Roseau fault), mapped and identified as active from high-resolution bathymetric data a few years before. This fault belongs to an arc-parallel en echelon fault system that follows the inner edge of the northern part of the Lesser Antilles arc, accommodating the sinistral component of oblique convergence between the North American and Caribbean plates. The distribution of aftershocks and damage (destruction and landslides) are consistent with the main fault plane location and attitude. The slip model of the main shock, obtained by inverting jointly global broadband and local strong motion records, is characterized by two main slip zones located 5 to 10 km to the SE and NW of the hypocenter. The main shock is shown to have increased the Coulomb stress at the tips of the ruptured plane by more than 4 bars where most of the aftershocks occurred, implying that failures on fault system were mainly promoted by static stress changes. The earthquake also had an effect on volcanic activity since the Boiling Lake in Dominica drained twice, probably as a result of the extensional strain induced by the earthquake and its main aftershock.
Journal Of Geophysical Research-solid Earth (0148-0227) (Amer Geophysical Union), 2011-10 , Vol. 116 , N. B10301 , P. 1-25

Droits : Copyright 2011 by the American Geophysical Union.
http://archimer.ifremer.fr/doc/00200/31099/29511.pdf
DOI:10.1029/2011JB008310
http://archimer.ifremer.fr/doc/00200/31099/

Éditeur(s) : Office Int Epizooties
Résumé : The tremendous development of penaeid shrimp culture across the world over the past twenty years has led to international trade in eggs, larvae and spawners of the best shrimp species for aquaculture. Trade has involved, in particular, the following species: - Penaeus japonicus from Japan to Europe, the Pacific Islands and South America - P. monodon from South-East Asia to almost all tropical countries - P. vannamei and P. stylirostris from countries along the Pacific coast of South and Central America to the United States of America, the islands of the South Pacific, countries along the Atlantic coast of the Americas and certain countries in Africa. In the 1980s, research conducted by American and French teams enabled the breeding of stocks of spawners in captivity. This resulted in the establishment of lines of captive broodstock outside natural areas of distribution, and the development of new breeding farms in previously unproductive regions. Trade related to movements of these species is facilitated by the absence of legislation in most countries; even when such legislation does exist, it is not always applied These practices have led to the rapid development of world shrimp production, but have also contributed to the dissemination of pathogens. In recent years, the occurrence of serious epizootics - occasioning heavy losses world-wide - has led to a more cautious approach involving trade of post-larvae obtained from captive broodstock in which thorough control measures have been implemented for known diseases. Trade in wild shrimp will probably be abandoned progressively, to avoid the risk of introducing new pathogens. The main challenges for research in the near future are the development of diagnostic tools, to enable continuous control of captive broodstock, and the selection of strains which are resistant to the principal pathogens affecting these species.
Revue Scientifique Et Technique-office International Des Epizooties (0253-1933) (Office Int Epizooties), 1996-06 , Vol. 15 , N. 2 , P. 499-515

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00091/20231/17883.pdf
http://archimer.ifremer.fr/doc/00091/20231/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We use 3-D mechanical modeling representing faults as planar surfaces with frictional properties that obey Coulomb-failure process to explore the long-term slip rates of the Altyn Tagh fault and Kunlun faults in the north Tibetan plateau. Crustal theology is simplified as an elastoplastic upper crust and a viscoelastic lower crust. Far-field GPS velocities and late Quaternary fault slip rates are used to constrain the model results. Rheological tests show that effective fault friction lower than 0.1-0.08 leads to high slip rates that fit with geologically and geodetically determined slip rates of the Kunlun fault (10-11.7 +/- 1.5 mm/yr). Meanwhile, the modeled Altyn Tagh fault reaches slip rates similar to 13.7 mm/yr to similar to 7.8 mm/yr in its central portion, between ranges of the geological slip rates. Associated with high slip rates, our model predicts that central Tibet (similar to 84 degrees E-95 degrees E) from the Altyn Tagh fault to the north of the Himalayan arc accommodates north-south shortening and east-west extension rates of similar to 10-12 mm/yr and similar to 8-10 mm/yr, respectively. We also question the widely accepted idea that interseismic strain is driven at the base of the seismogenic zone by a screw dislocation. If this assumption fails, the presented model implies that interseismic strain around large strike-slip faults could be distributed in a much broader way if the lithosphere deforms as a thin elastic plate rather than an elastic half-space with an embedded dislocation. If this distributed deformation is ignored, and the instantaneous surface deformation field modeled as that resulting from slip on a dislocation below a specified depth embedded in an elastic half-space, the estimated slip rate will inevitably be lower than the true long-term slip rate. This appears to explain why geodetic slip rates proposed for the Altyn Tagh fault (510 mm/yr) are lower than some of the geological slip rates. (C) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00411926
https://hal.archives-ouvertes.fr/hal-00411926
DOI : 10.1016/j.epsl.2008.06.049

Éditeur(s) : HAL CCSD
Résumé : International audience
The influence of Mn solute atoms on sub-grain boundary mobilities in Al has been determined by accurate electron backscatter diffraction analysis of the sub-grain sizes and misorientations during recovery annealing. High purity Al-0.1 and 0.3 wt.% Mn alloys were deformed by plane strain compression at room temperature to equivalent strains of 1.8 and annealed in the temperature range 150-300 °C. An original method of image analysis on sub-boundaries from electron backscatter diffraction maps was applied to quantify the sub-grain size distributions. The change in average sub-grain size with time at several temperatures was then used to estimate sub-grain boundary mobilities in both Al-Mn alloys. The activation energies for sub-grain mobility were found to be 48 and 52 and kJ.mol^-1 for the 0.1 and 0.3 % Mn alloys respectively, with the higher Mn alloy exhibiting lower rates. The sub-boundary mobilities are higher than expected from previous similar work on deformed Al-Si crystals. The orientation dependence of sub-grain growth is also examined.
International Journal of Materials Research

emse-00463551
https://hal-emse.ccsd.cnrs.fr/emse-00463551
DOI : 10.3139/146.110057

Éditeur(s) : HAL CCSD Springer Verlag/ASM International
Résumé : The use of zinc sheets has largely increased in the last years, fundamentally because of new tendencies in architecture and, at the same time, due to its excellent properties, as corrosion resistance under aggressive climatic conditions, malleability, recyclability, and surface finishing aspect. In the present work, the X-ray diffraction technique is used to characterize the crystallographic texture evolution of a strongly anisotropic Zn20 zinc sheet (Zn-Cu-Ti) subjected to uniaxial tension, plane strain, and equibiaxial tension, for specimens cut at 0, 45, and 90 deg with respect to the rolling direction. The crystallographic texture evolution is evaluated by means of pole figures, orientation distribution function, and Kearns factors. For all tested strain paths, deformation produces a decrease in the intensity of the crystallographic textures, due to a dispersion of the orientations of the different axes around the initial maxima.
ISSN: 1073-5623

hal-01583268
https://hal.archives-ouvertes.fr/hal-01583268
DOI : 10.1007/s11661-017-4069-y

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Networks of localized conjugate compactive shear bands with large dihedral angles (corresponding to so-called shear-enhanced compaction bands) were generated in 3-layer plane strain finite-difference models. The central layer has elastic–plastic properties with a small positive internal friction coefficient, negative dilatancy factor, and the hardening modulus reducing during the deformation. The two other layers are elastic. The spatial organization of the networks in the central layer, resulting from the elastic–plastic instability of the 3-layer system, was shown to be dependent on the contrast of the elastic stiffness of the layers and on the friction between them. When the stiffness E of the elastic layers and/or the friction are small, the networks are rather symmetric (the bands of both orientation families are distributed homogeneously within the layer). An increase in E at high friction, results in the clustering of the bands of one orientation along a layer segment which is followed by another segment filled with the bands of the other orientation. Different network types are characterized by different band spacing which is smaller in the clustered networks. The intensity of inelastic deformation and hence of porosity reduction within the bands are also smaller in this case. The obtained band networks are very similar to those in nature where the same variability of the network organization is observed. Available geological and mechanical data confirm the conclusions from the modeling about the origin of this variability.
ISSN: 0040-1951

hal-01116201
https://hal.archives-ouvertes.fr/hal-01116201
DOI : 10.1016/j.tecto.2014.01.021

Éditeur(s) : HAL CCSD
Résumé : This study is designed to improve the understanding of structural, mechanical and petrophysical characteristics of deformation bands in porous sandstone such as their potential influence on fluid storage or migration in reservoir setting. Structural and petrophysical analysis of band networks from Provence show that permeability of band is mainly controlled by the degree of cataclasis and diagenetic processes at depth. Map-scale analysis of band networks underlines the major influence of tectonic regime on band distribution, organization and permeability. Band associated to normal-fault regime (cataclasis and low-permeability) are located around map-sclae-fault whereas band associated to thurst-fault regime (moderate cataclasis and permeability) are pervasively distributed in all the area. Reverse-sense band are cataclastic and low-permeabiilty around the Roquemaure thrust, which show the potential role of large-scale fault on structural and petrophysical characteristics of bands. This analysis also shows the influence of fault propagation on formation of low permeability catacastic bands. This analysis suggests also granulometry as factor controlling organization of band networks.A mechanical analysis of deformation bands is realized based on results from Provence. Yield envelopes of these materials are calculated from analytical solution. Triaxial tests done on sandstone (L'Etang quarry, Orange) confirm the shape of yield envelope theoretically calculated. Triaxial tests done on the poorly-lithified sands (Boncavaï quarry, Uchaux) show grain size, sorting and packing influencing yield envelope and cataclastic band localization at shallow burial depth. Stress paths are calculated for burial and tectonic event (extension and contraction) using the relationship between main stress and secondary stresses (K0) calibrated from well data. These different results are integrated into a model which allows to estimate type and structural characteristics of bands susceptible to form for a known geological setting.A structural, mechanical and petrophysical model is established form these results. This model is calibrated by permeability data from deformation bands of Provence and results from the mechanical model of strain localization. This model is also confronted to a synthesis of permeability data from literature, which confirms the influence of the different controlling parameters integrated to the model. This model is applied for two sites of uranium exploration/exploitation in porous sandstone reservoirs and validated by field observations.
Cette étude est destinée à améliorer la compréhension des caractéristiques structurales, pétrophysiques et mécaniques des bandes de déformation dans les grès poreux ainsi que de leur rôle potentiel sur la migration ou le piégeage des fluides en milieu réservoir. L'analyse structurale et pétrophysique des réseaux de bandes de Provence montre que leur perméabilité découle principalement de l'intensité de la cataclase dans leur microstructure et des processus diagénétiques qui peuvent s'y localiser avec la profondeur. L'analyse régionale de ces réseaux de bandes souligne l'influence majeure du régime tectonique sur leur distribution, leur organisation et leur perméabilité. Les bandes associées au régime normal (cataclactiques et peu perméables) sont localisées autour des failles cartographiques, tandis que les bandes associées au régime inverse (modérement cataclastiques et perméables) sont distribuées dans toute la région. Les bandes inverses sont fortement cataclastiques et imperméables uniquement autour du chevauchement de Roquemaure ce qui montre le rôle potentiel de la présence de grande faille sur les caractéristiques structurales et pétrophysiques de ces bandes. D'autre part, cette analyse suggère que la granulométrie de l'encaissant peut influencer l'initiation et l'organisation des réseaux. L'analyse mécanique des bandes de déformation a ensuite été réalisée à partir des résultats obtenus en Provence. L'enveloppe de plasticité de ces matériaux est calculée à l'aide d'une solution analytique. Les essais triaxiaux menés sur le grès de la carrière de l'Etang (orange) confirment la forme de ces enveloppes estimées théoriquement. Les essais réalisés sur les sables de Boncavaï (Uchaux) montrent que la taille des grains, le tri et de la compaction dans ces matériaux peu lithifiés influent sur leurs enveloppes de plasticité et la localisation des bandes cataclastiques à faibles profondeurs. Les trajets de contraintes sont estimés pour les phases d'enfouissement et de chargement tectonique (extension et compression) à partir de la relation entre contrainte principale et contraintes secondaires (K0), calibrée à partir de données de forage. Ces résultats sont intégrés à un modèle permettant d'estimer la nature et les caractéristiques structurales des bandes susceptibles de se former dans un contexte géologique donné. Un modèle structural, mécanique et pétrophysique a été établir à partir de ces différents résultats. Ce modèle est calibré à partir des données de perméabilité mesurées sur les bandes de Provence et des résultats du modèle mécanique de localisation cité précédemment. Ce modèle a ensuite été confronté à une synthèse des données de perméabilité disponibles dans la littérature et confirme l'influence des différents paramètres de contrôle pris en compte dans le modèle. Ce modèle a enfin pu être appliqué sur deux sites d'explorations/exploitations d'uranium en réservoir gréseux poreux et validé par les résultats obtenus, en concordance avec les observations de terrain.
https://tel.archives-ouvertes.fr/tel-01001389

NNT : 2013MON20067
tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389/document
https://tel.archives-ouvertes.fr/tel-01001389/file/36072_BALLAS_2013_archivage-1_cor.pdf