Éditeur(s) : HAL CCSD Elsevier
Résumé : To contribute to the understanding of how opening-mode fractures (joints) form and open or close at depth in layered rocks, we present a 2D numerical study aiming to determine whether tensile stress can develop in pre-fractured elastic multilayers submitted to biaxial compressive strain conditions. First, we investigate the role of the elastic and geometrical properties of the layers on the development of tensile stress in models with five bonded layers and containing one open fracture in the central layer. Our results indicate that, in absence of elastic contrast (in Young's modulus) between the layers, no tensile stress develops in the models. However, when the fractured layer is stiffer than the two adjacent layers directly above and below, a lobe of horizontal tensile stress develops centered on the pre-existing fracture. The creation of this tensile stress is contingent upon the partial closing of the fracture. The levels of tensile stress and the thickness of the lobe of tensile stress increase logarithmically with an increase in the elastic contrast and are systematically larger for a larger Soft/Stiff ratio (ratio of the total thickness of the soft layers with the total thickness of the stiff layers). Second, we investigate the role of fracture interaction in the development of tensile stress in models containing a pair of open fractures. We observe that the levels of tensile stress in the region between the fractures are systematically higher than those observed in identical models containing a single fracture. This increase in tensile stress is very large for small elastic contrasts between the layers but diminishes when the elastic contrast increases. Furthermore, the spacing between the pre-existing fractures plays an important role in the stress distribution in the region between them. When the fracture spacing is equal to or lower than 1.15 times the height of the fractured layer for the experimental conditions chosen, the lobes of tensile stress centered on the fractures coalesce. This results in the formation of vast areas of tensile stress in models under remote compressive loading conditions. Such tensile areas are likely to allow the initiation and propagation of subsequent opening-mode fractures. The results obtained provide new insights into the formation of joints in layered rocks in compressive environments, with important consequences on fluid flow.
ISSN: 0040-1951

hal-00407576
https://hal.archives-ouvertes.fr/hal-00407576
DOI : 10.1016/j.tecto.2006.12.003

Éditeur(s) : HAL CCSD Elsevier
Résumé : We investigate experimentally the alteration of fractured class-G cement flowed by CO2-rich brine. The experiment mimics a mechanically damaged rough-walled fractured cement annulus at temperature 60 °C and pressure 10 MPa. The experiment consists of flowing a reservoir-equilibrated brine mixed with CO2 (partial pressure of 2.3 MPa) through the fracture of average aperture 14 μm at constant flow rate (100 μL min−1). This flow rate corresponds to pressure gradient representative of an average in situ hydrodynamic condition. Results indicate an intense alteration of the cement with a large removal of mass at the scale of the sample. However, the fracture alteration patterns are triggered by the initial heterogeneity of the fracture aperture; the aperture of the low aperture zones tends to decrease due to calcite precipitation whereas preferential paths develop in the zones of higher aperture associated. Nevertheless, the expected large permeability increase triggered by the mass removal is mitigated by the precipitation of a low density Si-rich amorphous material. The alteration rate will decrease with time because of the increasing distance of diffusion between the fracture where the reactants are actively renewed by advection and the portlandite and C-S-H dissolution fronts. The different zones of reaction can be adequately modeled by a simple 1D diffusion-reaction model using published kinetics coefficients and extrapolation to larger times than the experiment time can be drawn. Altogether, and in addition to the previous studies of the alteration of fractured well cement annulus, this study shows that the leakage potential is strongly controlled by the initial distribution of the aperture along the fracture: low aperture zones will tend to self-heal while localized flow in connected high aperture paths will be perennial.
ISSN: 1750-5836

hal-01346006
https://hal.archives-ouvertes.fr/hal-01346006
DOI : 10.1016/j.ijggc.2016.01.032

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : Experiments were conducted to assess the potential impact of fractured well-cement degradation on leakage rate. Permeability was monitored while CO2-enriched reservoir-equilibrated brine was flowed at constant rate through a single fracture in a class G cement core under conditions mimicking geologic sequestration environments (temperature 60 °C, pressure 10 MPa). The results demonstrate that, at least for the conditions used in the experiment, an initial leakage in a 42 μm aperture fracture (permeability = 1.5 × 10-10 m2) can be self-mitigated due to the decrease of the fracture hydraulic aperture after about 15 h. This decrease results from the development of continuous highly hydrated amorphous Si-rich alteration products at the edge of the fracture and the dense carbonation of the bulk cement that mitigate the penetration of the alteration front.
ISSN: 0013-936X

hal-00950088
https://hal.archives-ouvertes.fr/hal-00950088
DOI : 10.1021/es401317c

Éditeur(s) : HAL CCSD Elsevier
Résumé : Deficient sealing in the well cement plugs and annulus due to mechanical fracturing is an important risk of CO2 leakage from the reservoir to others permeable layers and the surface. Such situation was reproduced at laboratory scale in order to determine the hydro-chemical control on the fracture permeability. Specifically, we investigated the effect of CO2 rich-brine flowing through fractured Portland cements at T = 60 °C and P = 10 MPa and variable flow rates. We showed that carbonation process is dominant and induces permeability decrease and leakage mitigation for extremely low flow rate whereas for high flow rate injection the permeability remains constant due to the precipitation of a low density secondary Si-rich phase which maintains the initial fracture aperture. At intermediate flow rate the hydraulic aperture can increase due to the densification of the material triggered by the net precipitation of low porosity calcite. These results emphasize that more complex behaviors than those considered from batch experiments may take place in the vicinity of flowing fractures. Specifically, the redissolution of the neoformed calcite as well as the development of amorphous phases, both controlled by the CO2-rich brine renewing rate in the fracture may prevent the healing fracture.
ISSN: 1750-5836

hal-00857555
https://hal.archives-ouvertes.fr/hal-00857555
DOI : 10.1016/j.ijggc.2013.04.002

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The upward oil migration in a transparent and rough fracture containing a liquid of higher density is studied experimentally using a light transmission technique. The aperture heterogeneity is also measured by light transmission. The injection of oil in a fracture containing a heavier fluid produces a gravitational fingering instability. Depending on the injection velocity (capillary number, Ca) and the density difference between the two fluids (Bond number, Bo), different patterns are observed during the oil displacements. The width of the finger and its velocity are measured as a function of Bo and Ca. A stability analysis of the interface, based on a generalised Darcy equation in a two-dimensional fracture, allows an accurate description of the experimental results. The order of magnitude of the finger width and its velocity are in good agreement with the calculations, with small disparities due to various unknown fluid flow parameters: capillary pressure, finger thickness in the gap of the fracture, finger tortuosity and oil velocity field into the finger. The theoretical approach allows constructing a (Ca, Bo) phase diagram of stability of the interface.
ISSN: 0169-3913

hal-00429329
https://hal.archives-ouvertes.fr/hal-00429329
DOI : 10.1007/s11242-009-9340-2

Éditeur(s) : HAL CCSD
Résumé : The main purpose of this thesis was to characterize and to model the hydrodynamic and thermochemical processes leading to the alteration of the wellbore cement materials under borehole conditions. Percolation experiments were performed on fractured cement samples under CO2 storage conditions (60°C and 10MPa). Injection flow rate was dictated by the fracture aperture of each sample. CO2 enriched brine was flowed along the fracture aperture, and permeability changes as well as chemical evolution of major cations were continuously acquired during the experiment time. Reaction paths developed by the alteration of the cement were characterized using microtomography and ESEM images. The experiments conducted using samples presenting large fracture apertures during 5h showed that permeability was maintained constant during the experiment time. Three reacted layers were displaying by the alteration of portlandite and CSH. Long term experiment (26h) conducted with large initial fracture aperture showed a decrease of the permeability after 15hours of CO2 exposure. Otherwise, experiments performed on samples presenting narrow apertures indicated the conversion of portlandite and CSH to calcite leading to the permeability reduction and the fracture clogging. Assemblages of phases and chemical changes were modelled using GEMS-PSI speciation code. We studied also using a coupled transport-reactive model the conditions leading to the cement alteration and the formation of associated layers.
L'objectif de cette thèse était de modéliser à partir des expériences de percolation-réactive, les processus hydrodynamique et réactionnel qui gouvernent l'altération des ciments de puits. Différentes expériences ont été réalisées dans des conditions représentatives de celles du stockage du CO2. Des échantillons fracturés ont été utilisés pour injecter une saumure enrichie en CO2 à 60°C et 10MPa et à différentes pressions partielles de CO2. Le débitd'injection variait en fonction des propriétés hydrauliques de l'échantillon exposé. L'injection d'une saumure enrichie en CO2 à débit constant à travers une fracture supposée plane a permis d'étudier les modifications des propriétés hydrodynamiques et ces conséquences sur la géochimie et la microstructure du ciment altéré. L'impact dynamique de l'évolution microstructurale a été mis en évidence. Les expériences conduites sur des échantillons présentant de larges ouvertures, réalisées sur une durée de 5 h, ont montré que la perméabilité était maintenue constante le long de l'expérience. Trois couches d'altération se sont développées consécutivement à la dissolution de la portlandite et la décalcification des CSH. L'altération a entrainé la précipitation des carbonates et de la silice amorphe à proximité de la fracture. Dans le cas d'une expérience longue durée appliquant les mêmes conditions que précédemment on a observé que la croissance de la silice amorphe a entrainé la diminution de la perméabilité. Par ailleurs les expériences effectuées sur des échantillons présentant de faibles ouvertures, ont indiqué que la conversion de la portlandite en calcite conduit au colmatage de la fracture. L'évolution des assemblages de phases conduisant à la formation des carbonates et de la silice amorphe a été modélisée à partir du code géochimique GEMS. Les mécanismes de diffusion et les processus de mise en place des couches d'altération ont été étudiés à partir d'un modèle analytique et d'un modèle de transport réactif à partir du code géochimique PHREEQC.
https://tel.archives-ouvertes.fr/tel-01038034

tel-01038034
https://tel.archives-ouvertes.fr/tel-01038034
https://tel.archives-ouvertes.fr/tel-01038034/document
https://tel.archives-ouvertes.fr/tel-01038034/file/theseabdoulghafour.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Claystone caprocks are often the ultimate seal for CO2 underground storage when residual CO2 gas reaches the reservoir top due to buoyancy. Permeability changes of a fractured claystone due to seepage of CO2-enriched brine and water vapor-saturated CO2 gas are investigated. Results show that brine flow induces a large porosity increase (up to 50%) in the vicinity of the fracture due to dissolution of calcite and quartz, while permeability remains unchanged. Conversely, cyclic flows of CO2-brine and CO2-gas increase the fracture aperture abruptly after each gas flow period, producing a progressive decrease of the caprock seal capacity. Aperture increase is controlled by decohesion of the clay framework within a micrometer-scale-thick layer induced by CO2-gas acidification. Results show that hydraulic aperture increases linearly with duration of the preceding CO2-brine flow period, emphasizing the kinetic control of the quartz grains dissolution during the brine flow periods.
ISSN: 0094-8276

hal-00412332
https://hal.archives-ouvertes.fr/hal-00412332
DOI : 10.1029/2008GL034467