Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014

Éditeur(s) : Gauthier-Villars
Résumé : The dissolved Mn distribution on an oceanographic section along 50-degrees-W in the western North Atlantic shows decreasing concentrations in the offshore direction in the surface layer and with depth at the deep water stations. Leachable particulate Mn concentrations are low in the open ocean surface waters and elevated at intermediate depths. Dissolved Al concentrations in the surface layer are higher in the open ocean than on the shelf and the vertical distributions are characterized by surface maxima, a subsurface minimum at almost-equal-to 1 000 m and increasing concentrations in the deep waters. Leachable particulate Al concentrations are elevated on the shelf and in open ocean surface waters compared to the intermediate and deep waters. The Deep Western Boundary Current has high levels of dissolved Al and leachable particulate Mn and Al, and low levels of dissolved Mn. The distribution of dissolved Al is controlled primarily by inputs from atmospheric dust and removal onto biogenic particles. Both fluvial and atmospheric inputs affect dissolved Mn levels with removal occurring primarily by oxidation of Mn2+. The Al distribution is characterized by short residence times in shelf and surface waters and relatively constant distribution coefficients. The Mn distribution is characterized by longer surface water residence times, shorter deep water residence times, and more widely varying distribution coefficients than Al. Removal of Al by a surface adsorption mechanism and Mn by slower oxidation of Mn2+ are consistent with these observations. A model of Mn oxidation kinetics accurately predicts the intermediate depth leachable particulate Mn maximum.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1992 , Vol. 15 , N. 6 , P. 609-619

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00101/21186/18803.pdf
http://archimer.ifremer.fr/doc/00101/21186/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Synthetic hydroxylated titanium-bearing and undoped MgO-buffered forsterite crystals were heated at atmospheric pressure in air at temperatures from 800 to 1200 °C to determine hydrogen diffusion as a function of the type of point-defect mechanism by which the hydroxyl is incorporated. OH-stretching bands, measured by infrared spectroscopy, were assigned to the four substitution mechanisms: Ti-clinohumite point defects, silicon and magnesium vacancies, and point defects associated with trivalent cations. In the experiments at 800 to 1000 °C, hydrous defects related to trivalent cations and Mg-vacancies disappear first in the Ti-doped forsterite, followed by the hydrous defects related to Ti and a fraction of the hydrated Si-vacancies. Measured bulk diffusion coefficients for hydrogen exchange related to the latter process are one order of magnitude slower than previously reported and with higher activation energy (View the MathML source296±14 kJmol−1). After the elimination of the defects related to Ti, the hydroxyl concentration related to Si-vacancies remained constant for the duration of the experiments. This observation is in agreement with the very slow diffusivity of hydrogen in Si-vacancies measured in the undoped MgO-buffered dehydroxylation experiments at higher temperatures (from 1000 to 1200 °C), which were ∼3 orders of magnitude slower than previously reported at 1000 °C, and with an activation energy of View the MathML source461±11 kJmol−1. Hydrogen diffusion in forsterite is far more complex than previously assumed. This complexity can be used to gain more information on the timescales of the processes causing olivine to lose its structural “water”, but quantitative modeling will require not only the knowledge of the intrinsic diffusivities of the different hydrous defects but also their relative proportions and the possible reactions between them.
ISSN: 0012-821X

hal-01172253
https://hal.archives-ouvertes.fr/hal-01172253
DOI : 10.1016/j.epsl.2014.01.055

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Lithospheric-scale faults related to oblique subduction are responsible for some of the most hazardous earthquakes reported worldwide. The mega-thrust in the Sunda sector of the Sumatran oblique subduction has been intensively studied, especially after the infamous 2004 Mw 9.1 earthquake, but its onshore kinematic complement within the Sumatran subduction, the transform Sumatran Fault System, has received considerably less attention. In this paper, we apply a combination of analysis of Digital Elevation Models (ASTER GDEM) and field evidence to resolve the kinematics of the leading edge of deformation of the northern sector of the Sumatran Fault System. To this end, we mapped the northernmost tip of Sumatra, including the islands to the northwest, between 4.5°N and 6°N. Here, major topographic highs are related to different faults. Using field evidence and our GDEM structural mapping, we can show that in the area where the fault bifurcates into two fault strands, two independent kinematic regimes evolve, both consistent with the large-scale framework of the Sumatran Fault System. Whereas the eastern branch is a classic Riedel system, the western branch features a fold-and-thrust belt. The latter contractional feature accommodated significant amounts (c. 20%) of shortening of the system in the study area. Our field observations of the tip of the NSFS match a strain pattern with a western contractional domain (Pulau Weh thrust splay) and an eastern extensional domain (Pulau Aceh Riedel system), which are together characteristic of the tip of a propagating strike-slip fault, from a mechanical viewpoint. For the first time, we describe the strain partitioning resulting from the propagation of the NSFS in Sumatra mainland. Our study helps understanding complex kinematics of an evolving strike-slip system, and stresses the importance of field studies in addition to remote sensing and geophysical studies.
ISSN: 0040-1951

hal-01467196
https://hal.archives-ouvertes.fr/hal-01467196
DOI : 10.1016/j.tecto.2016.04.050

Éditeur(s) : HAL CCSD
Résumé : Gravitropism is a major process in vertical growth as it allows the positioning of plant in the gravity field and thus, for trees, it takes part in the light foraging strategies. Without any gravitropism, trees would adopt a weeping habit or fall on the ground due to the increasing with growth supported weight, especially at the advance regeneration stage (sapling stage) in the understorey, where tree are very slender and poorly stiff. Most of the gravitropic studies are made by physiologists in order to understand the process and thus are associated to complex laboratory methods (genetic engineering, anatomical studies, accurate 2D ou 3D measurements of form changes with time). In order to study the ecological relevance and the specific diversity of gravitropic performances in natural forests, we developed a framework that uses different kinds of datas. Synchronical analysis has been done i) at the population level in large sample of trees and ii) at the tree level from destructive measurement of the dissymmetry maturation strains known to be the main motor of the posture control reaction of trees. In both cases, biomechanical models allows to estimate some aspects of the dynamic gravitropic process. Diachronical analysis has been done in natural conditions on permanent plots, or in a more traditional way, by observing in greenhouse experiments the righting movements of plants artificially tilted. In the first case, the problem is the high variability of natural disturbances and the slowness of growth and movements in the dark understorey. The second choice allows a measurement of a capacity (i.e. the ability of the species to react in quite extreme conditions of verticality disturbance but good for growth light and nutrient conditions) that is more easy to analyse, but is maybe not so relevant for estimating the ecological strategy (some species could have developed a high efficience of gravitropic reaction in natural conditions by avoiding the mechanical disturbance or adapting the reaction to slow growth and changing environments in natural conditions). All approaches use the same basic biomechanical modelling, i) to analyse simultaneously the reaction and the disturbance (due to the weight increase) during growth, or ii) to combine different parameters (geometry, growth, weight, maturation strains) involved in shape changes and posture control. They give a classification of the species according to their gravitropic performances. Results on 15 species are discussed, with relation to shade-tolerance or avoidance.
6th Plant Biomechanics Conference
Cayenne, France

hal-00565956
https://hal.archives-ouvertes.fr/hal-00565956

Résumé : Dans cette thèse, nous étudions quelques modèles de flux migratoire. Nous sommes intéressés par le pays d’origine du migrant ainsi que par son pays d’accueil. Plus précisément, nous étudions les modèles où la probabilité de migration desagents dépend de leur capital humain (essentiellement l’éducation). Il y a deux cas importants qu’il convient de distinguer : le cas où les individus migrent avec le capital humain hérité de leurs parents et le cas le plus difficile, à solutions multivoques, lorsque les individus migrent avec le capital humain qu’ils auront dans le futur.Dans le premier cas, nous retrouvons les résultats obtenus la littérature. De plus, nous étendons aux cas de populations non constantes et nous proposons d’autres modèles. Dans le second cas, où les individus peuvent migrer en fonction de leurcapital humain futur, nous proposons différents mécanismes de sélection où les convergences vers une unique valeur de capital humain sont démontrées à chaque fois.
In this thesis, we study some migration models from a mathematical point of view. We are interested by the country of origin of migrant as well as in his host country.More precisely, we study the models where the probability of migration of individuals depends on their human capital (essentially education). There are two important cases to be distinguished : the case where individuals migrate with thehuman capital inherited from their parents and the more difficult case -since it is generally a multivalued case- where the individuals migrate with the human capital they will obtain in the future.In the first case, we obtain some results similar to the ones found in literature. Moreover, we study the case of non constant populations and we propose other models. In the second case, where the individuals can migrate following the human capital they will have in the future, we obtain different selection mechanisms for which the human capital converges to a unique value at each time.

http://www.theses.fr/2013AGUY0704/document

Éditeur(s) : HAL CCSD
Résumé : International audience
Understanding subduction rheology in both space and time has been a challenge since the advent of plate tectonics. We herein focus on "subduction infancy", that is the first ~1-5 My immediately following subduction nucleation, when a newly born slab penetrates into the upper plate mantle and heats up. The only remnants of this critical yet elusive geodynamic step are thin metamorphic soles, commonly found beneath pristine, 100-1000 km long portions of oceanic lithosphere emplaced on continents (i.e., ophiolites).Through the (i) worldwide compilation of pressure-temperature conditions of metamorphic sole formation augmented by pseudosection thermodynamic modeling, (ii) calculations of the viscosity of materials along the plate interface and (iii) generic numerical thermal models, we provide a conceptual model of dynamic plate interface processes during subduction infancy (and initiation s.l.).We show in particular how major rheological switches across the subduction interface control slab penetration, and the formation of metamorphic soles. Due to the downward progression of hydration and weakening of the mantle wedge with cooling, the lower plate (basalt, sediment) and the upper plate (mantle wedge) rheologies equalize and switch over a restricted temperature-time-depth interval (e.g., at ~800°C and ~1 GPa, during 0.1-2 My, for high-temperature metamorphic sole formation). These switches result in episodes of maximum interplate mechanical coupling, thereby slicing the top of the slab and welding pieces (basalt, sediment) to the base of the mantle wedge. Similar mechanical processes likely apply for the later, deeper accretion and exhumation of high-temperature oceanic eclogites in serpentinite mélanges, or for the accretion of larger tectonic slices.This model provides constraints on the effective rheologies of the crust and mantle and general understanding, at both rock and plate scale, for accretion processes and early slab dynamics.
AGU Fall Meeting 2015
San Francisco, United States

insu-01242103
https://hal-insu.archives-ouvertes.fr/insu-01242103

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Deformation of the continental lithosphere is traditionally modeled assuming that heat production in the subcontinental lithospheric mantle is negligible. Although this may be appropriate for highly depleted Archean lithosphere, studies of mantle xenoliths and lithospheric-derived mafic rocks suggest that heat productions of up to 0.4 ;μW/m3 may be attained in the mantle of Phanerozoic and Neoproterozoic regions due to modal metasomatism. To investigate the effect of a local enrichment in heat-producing elements within the lithospheric mantle on the continental deformation, we performed a series of 2D thermo-mechanical models simulating the deformation of a lithospheric plate 1000 km long, which contains in its central part a 200 km wide and 20 km-thick mantle layer with a heat production of 0.05;–0.25 ;μW/m3 between 40 and 80 km depth, leading to a local enhancement of the surface heat flow by 1;–5 mW/m2. Compression models show that a 20 km-thick layer with a heat production as low as 0.05 ;μW/m3 within the shallow lithospheric mantle leads to strain localization in both the enriched mantle and the overlying crust. Strain localization depends exponentially on the temperature increase in the lithosphere section, which is controlled by the volume of metasomatized mantle and the intensity of the metasomatic enrichment in heat-producing elements. A heat production of 0.25 μW/m3 between 60 and 80 km depth results, for instance, in strains within and above the metasomatized mantle 5 times higher than in the surrounding lithosphere. Strain localization also depends on the location of the heat-producing domain and on the plate rheological structure; deeper heat-producing domains and weaker plates leading to stronger localization. These results provide an explanation for strain localization in intraplate environments, leading to the formation of orogenic belts situated hundreds to thousands of kilometers away from known plate boundaries, as observed in the Neoproterozoic belts of Gondwana and in the present-day deformation of the Asian plate.
ISSN: 0012-821X

hal-00411386
https://hal.archives-ouvertes.fr/hal-00411386
DOI : 10.1016/j.epsl.2008.07.040

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either “artificially”, or by natural extractives.
Wood Science and Technology

hal-01096868
https://hal-agroparistech.archives-ouvertes.fr/hal-01096868
DOI : 10.1007/S00226-010-0393-8

Éditeur(s) : HAL CCSD
Résumé : International audience
While the impact of network properties on information spread- ing is now widely studied, in uence of network dynamics is very little known. In this paper, we study how evolution mechanisms tradition- ally observed within social networks can a ect information di usion. We present an approach that merges two models: model of informa- tion di usion through social networks and model of network evolution. Since epidemics provide a reference in application domains of information spreading, we measure the impact of basic network structure changes on epidemic peak value and timing. Then we investigate observed trends in terms of changes appearing in the network structure. Our results provide promising results on how and why network dynamics is a strong param- eter to integrate in requirements for information spreading modelling.
World Summit on the Knowledge Society
Mykonos, Greece

hal-00768405
https://hal.archives-ouvertes.fr/hal-00768405

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Rainbow is a dome-shaped massif at the 36°14′N nontransform offset along the Mid-Atlantic Ridge. It hosts three ultramafic-hosted hydrothermal sites: Rainbow is active and high temperature; Clamstone and Ghost City are fossil and low temperature. The MoMARDREAM cruises (2007, 2008) presented here provided extensive rock sampling throughout the massif that constrains the geological setting of hydrothermal activity. The lithology is heterogeneous with abundant serpentinites surrounding gabbros, troctolites, chromitites, plagiogranites, and basalts. We propose that a W dipping detachment fault, now inactive, uplifted the massif and exhumed these deep-seated rocks. Present-day deformation is accommodated by SSW-NNE faults and fissures, consistent with oblique teleseismic focal mechanisms and stress rotation across the discontinuity. Faults localize fluid flow and control the location of fossil and active hydrothermal fields that appear to be ephemeral and lacking in spatiotemporal progression. Markers of high-temperature hydrothermal activity (∼350°C) are restricted to some samples from the active field while a more diffuse, lower temperature hydrothermal activity (<220°C) is inferred at various locations through anomalously high As, Sb, and Pb contents, attributed to element incorporation in serpentines or microscale-sulfide precipitation. Petrographic and geochemical analyses show that the dominant basement alteration is pervasive peridotite serpentinization at ∼160–260°C, attributed to fluids chemically similar to those venting at Rainbow, and controlled by concomitant alteration of mafic-ultramafic units at depth. Rainbow provides a model for fluid circulation, possibly applicable to hydrothermalism at oceanic detachments elsewhere, where both low-temperature serpentinization and magmatic-driven high-temperature outflow develop contemporaneously, channeled by faults in the footwall and not along the detachment fault.
ISSN: 1525-2027

hal-01115281
https://hal.archives-ouvertes.fr/hal-01115281
https://hal.archives-ouvertes.fr/hal-01115281/document
https://hal.archives-ouvertes.fr/hal-01115281/file/Andreani_et_al-2014-Geochemistry%2C_Geophysics%2C_Geosystems.pdf
DOI : 10.1002/2014GC005269

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Based on observations from both modem convergent margins and sandbox modeling, we examine the possible conditions favoring frontal accretion and/or frontal and basal tectonic erosion. Mean characteristic parameters (!.t, !.t* • and [) are used to discuss the mechanical stability of 28 transects across the frontal part of convergent margins where the Coulomb theory is applicable. Natural observations reveal that "typical accretionary wedges" are characterized by low tapers with smooth surface slope and subducting plate, low convergence rates and thick trench sediment, while "nonaccretionary wedges" display large tapers with irregular surface slopes and rough subducting plate, high convergence rates and almost no trench fill. Sandbox experiments were performed to illustrate the effects of seamounts/ridges in the subduction zone on the deformation of an accretionary wedge. These experiments show that a wedge of sand is first trapped and pushed in front of the seamount which acts as a moving bulldozer. This is followed by a tunnelling effect of the subducting seamount through the frontal wedge material, which results in considerable sand reworking. At an advanced subduction stage, the d6collement jumps back from a high level in the wedge to its former basal position. We conclude that a high trench sedimentation rate relative to the convergence rate leads to frontal accretion. In contrast, several conditions may favor tectonic erosion of the upper plate. First, oceanic features, such as grabens, seamounts or ridges, may trap upper plate material during their subduction process. Second, destabilization of the upper plate material by internal fluid overpressuring causing hydrofracturing is probably another important mechanism.
ISSN: 0148-0227

hal-01261600
https://hal.archives-ouvertes.fr/hal-01261600
https://hal.archives-ouvertes.fr/hal-01261600/document
https://hal.archives-ouvertes.fr/hal-01261600/file/lallemandJGR1994.pdf

Résumé : Dans le cas des DOM, singulièrement la Guadeloupe, qui sont à l'aube de l'expérimentation de réformes profondes de politiques économiques, l'élaboration d'un outil de simulation macroéconomique tel qu'un MEGC apparaît naturellement comme une exigence plus que souhaitable. Ce recours à la construction de modèles spécifiques pour les DOM est en parfaite cohérence avec l'une des principales conclusions du rapport d'information diligenté par le Sénat aux lendemains de la crise sociale du début de l'année 2009. Les appels à projet de la Commission europèenne et du Ministère de l'Outre-mer vont justement dans le sens de pallier celte carence puisque la politique économique des RUP de façon générale est conduite à vue sans aucun outil d'investigation ex ante. Nous avons conçu plusieurs modèles. Parmi eux, CloDyn est le premier modèle macroéconomique pour les DOM à vocationopérationnelle. Composée de plus de 2000 équations, ce modèle d'équilibre général calculable tient compte de nombreuses rigidités sur les marchés des biens et services et du travail et se décline sous deux versions: statique et dynamique. Les élasticités ont fait l'objet d'estimations économétriques. Il tient compte de nombreuses spécificités tant au niveau de la fiscalité de ces régions (octroi de mer, taxe sur les carburants, subventions à l'exportation) que du coût des facteurs (exonérations des charges sur les bas salaires, sur rémunératio des fonctionnaires). Il repose sur une formalisation des mécanismes en oeuvre dans ces économies que nous avons appelé le DOM disease pour expliquer les dysfonctionnements persistants sur le plan macroéconomique.
In the case of the French overseas regions, particularly of Guadeloupe, which are just beginning to experiment with economic policies radical reforrns, the development of a macroeconomic simulation tool such as a CGE model appears naturally as a highly desirable requirement. The use of the construction of specifie models for DOM is fully consistent with a major finding of the report commissioned by the Senate in the aftermath of the social crisis of the early 2009. As a malter of facts, the purpose of the calls for project initiated by the European Commission and the Ministry of Overseas is to remedy this deficiency, since the RUP economie policy is generally to conduct no investigation tool ex ante. We designed several models. Among them, CloDyn is the first operational DOM-based macroeconomic rnodel. Composed of more than 2000 equations, this computable general equilibrium model takes into account many rigidities in the markets for goods and services and labor and is available in two versions: static and dynamic. Elasticities have been econometrically estimated. lt rests on many features of both taxation (dock dues, fuel tax, export subsidies) and the cost factors (exemption from charges on low wages, remuneration of civil servants). Il is based on a formalization of the mechanisms at work in these economies we calied the DOM disease to explain the persistent failures in such economies. lt also evaluates the monetary poverty among households with the use of a block of microsimulation model and we allow a profane in GAMS to use this tool and conduct its own analytical work thanks to a user friendly interface.

http://www.theses.fr/2011AGUY0411/document

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Cell death of hepatocytes is a prominent characteristic in the pathogenesis of liver disease, while hepatolysis is a starting point of inflammation in hepatitis and loss of hepatic function. However, the precise molecular mechanisms of hepatocyte cell death, the role of the cytokines of hepatic microenvironment and the involvement of intracellular kinases, remain unclear. Tumor necrosis factor alpha (TNF-α) is a key cytokine involved in cell death or survival pathways and the role of RIPK1 has been associated to the TNF-α-dependent signaling pathway. We took advantage of two different deficient mouse lines, the RIPK1 kinase dead knock-in mice (Ripk1K45A) and the conditional knockout mice lacking RIPK1 only in liver parenchymal cells (Ripk1LPC-KO), to characterize the role of RIPK1 and TNF-α in hepatitis induced by concanavalin A (ConA). Our results show that RIPK1 is dispensable for liver homeostasis under steady-state conditions but in contrast, RIPK1 kinase activity contributes to caspase-independent cell death induction following ConA injection and RIPK1 also serves as a scaffold, protecting hepatocytes from massive apoptotic cell death in this model. In the Ripk1LPC-KO mice challenged with ConA, TNF-α triggers apoptosis, responsible for the observed severe hepatitis. Mechanism potentially involves both TNF-independent canonical NF-κB activation, as well as TNF-dependent, but canonical NF-κB-independent mechanisms. In conclusion, our results suggest that RIPK1 kinase activity is a pertinent therapeutic target to protect liver against excessive cell death in liver diseases. © The Author(s) 2016.
ISSN: 2041-4889

hal-01414916
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01414916
DOI : 10.1038/cddis.2016.362
PUBMED : 27831558

Résumé : L’objet de cette thèse est l’étude des comportements mécanique et à la corrosion d’un nouveau système de fondation, dit pieux SPIRMEC, adapté aux structures légères. Le travail s’est focalisé sur deux grands aspects. Le premier aspect concerne l’analyse du comportement sous chargement axiale des pieux SPIRMEC sur la base de l’expérimentation et de la modélisation numérique dans un sol mou non cohésif. Quant au deuxième aspect, il traite du problème de la corrosion de l’acier constituant le pieu dans un environnement tropical humide. Le comportement des pieux SPIRMEC sous une charge axiale de traction, dans un sol fin non cohésif, a montré le développement d’une surface cylindrique de rupture. Celle-ci ne dépend pas de la configuration géométrique des pieux tel que : l’espacement S, le diamètre d’hélice Dh et le diamètre du tube d. En adoptant ce critère de rupture et à l’aide d’une analyse statistique des données, nous avons proposé quatre méthodes analytiques de prédiction de la capacité portante des pieux SPIRMEC à partir des essais in-situ et au laboratoire qui sont: •Méthode CPT basée sur la résistance de pointe pénétromètrique (essai CPT), •Méthode MPT basée sur la pression limite pressiomètrique (essai MPT), •Méthode du couple d’installation, •Méthode analytique basée sur les paramètres de cisaillement de sol notamment l’angle de frottement interne (essais triaxial et boîte de cisaillement). Ces méthodes tiennent compte de la géométrie du pieu, du procédé de mise en oeuvre et de la compacité du sol. L’analyse de performance des méthodes proposées a montré que les méthodes analytique et CPT représentent mieux le comportement des pieux testés. La modélisation numérique du comportement des pieux SPIRMEC sous charge axiale de traction a été également étudiée à l’aide du code de calcul Plaxis 2D. Un modèle axisymétrique a été adopté pour modéliser la géométrie de la structure. Le modèle de comportement hardening soil a été retenu pour modéliser le comportement élastoplastiq des couches de sol. Un modèle élastique linéaire a été retenu pour le pieu. Quant au comportement de l’interface sol-structure, il a été pris en compte par un modèle élastoplastique basé sur les critères de Mohr-Coulomb. L’expansion du sol résultant de l’installation des pieux a été approchée par une cavité cylindrique. Cette dernière a été modélisée par des déformations volumiques anisotropes. Nous avons constaté, qu’appliquer une déformation volumique de l’ordre de 40% permet une bonne concordance entre les résultats numériques et expérimentaux. L’étude paramétrique nous a également permis de constater l’existence d’une variation linéaire entre la capacité portante et l’espacement S. Le comportement de l’acier galvanisé dans le sol a été également étudié au moyen de trois approches: électrochimique, visuelles grâce au microscope électronique et gravimétrique. Les tests électrochimiques de corrosion du zinc ont été réalisés dans la solution de sol artificielle pour deux périodes bien distinctes : saison des pluies et après 8 mois de contact sol-pieu. Une forte dépendance est constatée de la vitesse de corrosion de zinc au pH et à la conductivité de la solution. La vitesse de corrosion est plus importante en saison des pluies qu’après 8 mois de contact de pieu avec le sol. Les fortes concentrations en sulfates semblent augmenter la vitesse de corrosion. Les analyses menées au MEB montrent que la zone de fluctuation de nappe et en surface externe (sol/air) sont les zones les plus corrodées. La comparaison entre les différentes techniques d’évaluation de la vitesse de corrosion a montré que l’eau de nappe peut être utilisée comme un milieu représentatif du profil chimique d’un sol non cohésif et légèrement granulaire.
The purpose of this thesis is to study the both behaviors mechanical and of the corrosion of a new foundation system, called spirec piles, for lightweight structures. The work was based on two main aspects. The first aspect concerns the analysis of behavior of the spirmec piles under axial loading on the basis of experimental and numerical modeling in a non-cohesive soft soil. On the second aspect, it addresses the problem of corrosion of steel forming the pile in a humid tropical environment. The behavior of the tested piles under axial traction load, in a non-cohesive soil, showed the development of a cylindrical surface of failure. This does not depend on the geometrical configuration of the tested piles such that: the spacing s, the helix diameter dh and the diameter of the shaft. By adopting this failure criterion and using statistical data analysis, we proposed four analytical methods for predicting the bearing capacity of the piles from in-situ and laboratory tests, which are: cpt method based on tip resistance penetrometer (cpt test), mpt method based on pressuremeter limit pressure (test mpt), method of installation torque and analytical method based on the shear parameters of soil (triaxial tests and shear box). These methods take into account the geometry of the pile, the method and implementation of soil compaction. Performance analysis of the proposed methods showed that the analytical methods and cpt represent better the behavior of piles tested. An axisymmetric condition was assumed to model this geometry in two-dimensional space. In this study, we proposed to model the pipe screw pile with plates elements available in plaxis 2d. The helixes were modeled as circular disks. Interface elements were incorporated along the pile to simulate the soil-pile interaction. Hardening soil model was chosen to describe the soil with drained behavior was assigned for all layers. Linear elastic for pile and elastic plastic model based on the mohr-coulomb criterion was used to describe the interface behavior. The lateral expansion generated by the pile shaft was modeled by anisotropic volumetric strains (ɛxx=ɛzz, ɛyy=0). The pile behavior under tensile loading at different volumetric strains, it is clear that the best fit was obtained at volumetric strain of 40%. The parametric study also allowed us to establish the existence of a linear variation between the bearing capacity and spacings. The behavior of the galvanized steel in the ground has also been studied using three approaches such as: electrochemical, microscopic imaging and gravimetrically. Electrochemical tests of the corrosion of the zinc have been made in artificial soil solution into two periods, the rainy season and after eight months of contact soil-pile. Is a strong dependence of the observed corrosion rate of the zinc at the ph and conductivity of the solution. The corrosion rate is higher in the rainy season compared to eight months of contact of the pile with soil. High sulfate concentrations increase the rate of corrosion. The meb analysis shows that the fluctuation zone of the water table is the most corroded area. Comparison between the different methods of evaluating the corrosion rate showed that the ground water may be used as a representative profile of the chemical environment of a non-cohesive soil and slightly granular.

http://www.theses.fr/2014AGUY0790/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The present study aims at better deciphering the different mechanisms involved in the functioning of the subduction interplate. A 2D thermo-mechanical model is used to simulate a subduction channel, made of oceanic crust, free to evolve. Convergence at constant rate is imposed under a 100 km thick upper plate. Pseudo-brittle and non-Newtonian behaviours are modelled. The influence of the subduction channel strength, parameterized by the difference in activation energy between crust and mantle () is investigated to examine in detail the variations in depth of the subduction plane down-dip extent, . First, simulations show that numerical resolution may be responsible for an artificial and significant shallowing of if the weak crustal layer is not correctly resolved. Second, if the age of the subducting plate is 100 Myr, subduction occurs for any . The stiffer the crust is, that is, the lower is, the shallower is (60 km depth if kJ/mol) and the hotter the fore-arc base is. Conversely, imposing a very weak subduction channel ( J/mol) leads there to an extreme mantle wedge cooling and inhibits mantle melting in wet conditions. Partial kinematic coupling at the fore-arc base occurs if kJ/mol. If the incoming plate is 20 Myr old, subduction can occur under the conditions that the crust is either stiff and denser than the mantle, or weak and buoyant. In the latter condition, cold crust plumes rise from the subduction channel and ascend through the upper lithosphere, triggering (1) partial kinematic coupling under the fore-arc, (2) fore-arc lithosphere cooling, and (3) partial or complete hindrance of wet mantle melting. then ranges from 50 to more than 250 km depth and is time-dependent if crust plumes form. Finally, subduction plane dynamics is intimately linked to the regime of subduction-induced corner flow. Two different intervals of are underlined: 80–120 kJ/mol to reproduce the range of slab surface temperature inferred from geothermometry, and 10–40 kJ/mol to reproduce the shallow hot mantle wedge core inferred from conditions of last equilibration of near-primary arc magmas and seismic tomographies. Therefore, an extra process controlling mantle wedge dynamics is needed to satisfy simultaneously the aforementioned observations. A mantle viscosity reduction, by a factor 4–20, caused by metasomatism in the mantle wedge is proposed. From these results, I conclude that the subduction channel down-dip extent, , should depend on the subduction setting, to be consistent with the observed variability of sub-arc depths of the subducting plate surface.
ISSN: 0031-9201

hal-01623155
https://hal.archives-ouvertes.fr/hal-01623155
DOI : 10.1016/j.pepi.2017.05.008

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : International audience
The seismological study of recent seismic crises near Oleron Island confirms the coexistence of an extensional deformation and a transtensive regime in the Atlantic margin of France, which is different from the general western European stress field corresponding to a strike-slip regime. We argue that the switch of the principal stress axes σ1/σ2 in a NW-SE vertical plane is linked with the existence of crustal heterogeneities. Events of magnitude larger than 5 sometimes occur along the Atlantic margin of France, such as the 7 September 1972 (ML = 5.2) earthquake near Oleron island and the 30 September 2002 (ML = 5.7) Hennebont event in Brittany. To test the mechanism of local strain localization, we model the deformation of the hypocentral area of the Hennebont earthquake using a 3D thermo-mechanical finite element code. We conclude that the occurrence of moderate earthquakes located in limited parts of the Hercynian shear zones (as the often reactivated swarms near Oleron) could be due to local reactivation of pre-existing faults. These sporadic seismic ruptures are favoured by stress concentration due to rheological heterogeneities.
ISSN: 1631-0713

hal-00936220
https://hal.archives-ouvertes.fr/hal-00936220
DOI : 10.1016/j.crte.2013.07.004

Éditeur(s) : HAL CCSD Elsevier
Résumé : Validation of building energy simulation programs is of major interest to both users and modellers. To achieve such a task, it is essential to apply a methodology based on a priori test and empirical validation. A priori test consists in verifying that models embedded in a program and their implementation are correct. this should be achieved before carrying out experiments. The aim of this report is to present results from the application of the BESTEST procedure to our code. We will emphasise the way it allows to find bugs in our program and also how it permits to qualify models of heat transfer by conduction
World Renewable Energy Congress VI Renewables: The Energy for the 21st Century World Renewable Energy Congress VI 1-7 July 2000 Brighton, UK

ISBN : 978-0-08-043865-8
hal-00767562
https://hal.archives-ouvertes.fr/hal-00767562
https://hal.archives-ouvertes.fr/hal-00767562/document
https://hal.archives-ouvertes.fr/hal-00767562/file/TedWrec2000.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
We consider a second-order differential system with Hessian-driven damping . An interesting property of this system is that, after introduction of an auxiliary variable y , it can be equivalently written as a first-order system in time and space. This allows us to extend the analysis to the case of a convex lower semicontinuous potential and so to introduce constraints in the model. When considering the indicator function of a closed convex set, the subdifferential operator takes account of the contact forces. In this setting, by playing with the geometrical damping parameter, we can describe nonelastic shock laws with restitution coefficient. Taking advantage of the infinite dimensional framework, we introduce a nonlinear hyperbolic PDE describing a damped oscillating system with obstacle. The system is dissipative; in the convex case each trajectory weakly converges to a minimizer of the global potential energy function. Exponential stabilization is obtained under strong convexity assumptions.
Differential Equations & Applications

hal-00803214
https://hal.archives-ouvertes.fr/hal-00803214
https://hal.archives-ouvertes.fr/hal-00803214/document
https://hal.archives-ouvertes.fr/hal-00803214/file/Attouch-Mainge-Redont-30August2011.pdf

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Assessing seismic hazards remains one of the most challenging scientific issues in Earthsciences. Deep tectonic processes are classically considered as the only persistentmechanism driving the stress loading of active faults over a seismic cycle. Here we show via amechanical model that erosion also significantly influences the stress loading of thrust faultsat the timescale of a seismic cycle. Indeed, erosion rates of about B0.1–20mmyr1, asdocumented in Taiwan and in other active compressional orogens, can raise the Coulombstress by B0.1–10 bar on the nearby thrust faults over the inter-seismic phase. Masstransfers induced by surface processes in general, during continuous or short-lived andintense events, represent a prominent mechanism for inter-seismic stress loading offaults near the surface. Such stresses are probably sufficient to trigger shallow seismicity orpromote the rupture of deep continental earthquakes up to the surface.
ISSN: 2041-1723

insu-01087103
https://hal-insu.archives-ouvertes.fr/insu-01087103
https://hal-insu.archives-ouvertes.fr/insu-01087103/document
https://hal-insu.archives-ouvertes.fr/insu-01087103/file/Steer2014_NatureComm_accepted.pdf
DOI : 10.1038/ncomms6564