Éditeur(s) : HAL CCSD
Résumé : Today, one of the main challenges in the oil industry is the exploitation of new resources in naturally fractured reservoirs often located in structurally complex areas such as plate boundaries, mountain ranges or near salt structures. While numerical models of rock deformation based on continuum mechanics are becoming industry standard in providing efficient means for modelling natural fractures in reservoirs, the knowledge of past perturbed stress fields, which is referred as the type (normal, wrench or reverse), orientation and magnitude of the regional or local tectonic stresses that needs to be applied as boundary condition in numerical simulations, is often unknown or approximated.The essence of this thesis is to improve the recovery of the paleostress field needed to constrain numerical simulations. I first described and discuss through a comprehensive mechanically-based multi-parametric study how far we can rely on the commonly used paleostress inversion methods based on fault slip data and the Wallace and Bott assumptions. I then compared this method with a new generation technique based on geomechanics using field observations. Since slip markers on faults are hardly observed in core or image log, I used observed natural fracture data as main drivers for the inversion of the paleostress using geomechanically-based method. I demonstrated, through various outcrop and subsurface examples, how this can efficiently be done. Finally, I aimed at addressing the problem of polyphase fracture data sets with unknown mechanical type (joints, faults, stylolites ...) and expanded the mechanical stress inversion to the separation of tectonic phases.
Aujourd'hui, l'un des principaux défis dans l'industrie pétrolière est l'exploitation de nouvelles ressources dans les réservoirs naturellement fracturés souvent situés dans des zones structurellement complexes tels que les frontières de plaques, les chaînes de montagnes ou les structures de proches des dômes de sel. Alors que les modèles numériques de déformation des roches basée sur la mécanique des milieux continus fournissant des moyens efficaces pour la modélisation de fractures naturelles dans les réservoirs, sont devenus la norme dans l'industrie, les paléo-contraintes régionales ou locales appliquées comme condition aux limites dans les simulations numériques, définies par le régime (normal, décrochant ou inverse), l'orientation, et la magnitude des contraintes tectoniques, sont souvent inconnues ou approximées.L'essence de cette thèse est d'améliorer la prédiction du champ de paléo-contrainte nécessaire pour contraindre les simulations numériques. J’ai décrit dans un premier temps à travers une étude comparative multi-paramétrique complète basée sur la mécanique, dans quelle mesure nous pouvions compter sur les méthodes d'inversion des paléo-contraintes basées sur les hypothèses de Wallace et Bott et les données de glissement sur les failles. J’ai ensuite comparé ces méthodes avec une technique d’inversion de nouvelle génération basée sur la géomécanique en utilisant les observations de terrain. Puisque les marqueurs de glissement sur les failles sont rarement observés le long du forage, j’ai utilisé l’inversion géomécanique des contraintes pour les données de fractures naturelles observées. J’ai alors démontré, l’efficacité de cette technique à travers divers exemples d'affleurements et de subsurface. Enfin, j’ai proposé une solution afin de résoudre le problème des données de fractures polyphasées à type cinématique inconnu (joints, failles, stylolites ...) et étendu l’inversion de contrainte basée sur la géomécanique à la séparation des phases tectoniques.
https://hal.archives-ouvertes.fr/tel-01324110

tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110/document
https://hal.archives-ouvertes.fr/tel-01324110/file/theselejri.pdf

Éditeur(s) : HAL CCSD
Résumé : Different applications of linear elasticity in structural geology are presented in this thesis through the development of three types of numerical computer codes. The first one uses forward modeling to study displacement and perturbed stress fields around complexly faulted regions. We show that incorporating inequality constraints, such as static Coulomb friction, enables one to explain the angle of initiation of jogs in extensional relays. Adding heterogeneous material properties and optimizations, such as parallelization on multicore architectures and complexity reduction, admits more complex models. The second type deals with inverse modeling, also called parameter estimation. Linear slip inversion on faults with complex geometry, as well as paleo-stress inversion using a geomechanical approach, are developed. The last type of numerical computer code is dedicated to restoration of complexly folded and faulted structures. It is shown that this technique enables one to check balanced cross-sections, and also to retrieve fault chronology. Finally, we show that this code allows one to smooth noisy 3D interpreted faulted and folded horizons using geomechanics.
Différentes applications de l'élasticité linéaire en géologie structurale sont présentées dans cette thèse à travers le développement de trois types de codes numériques. Le premier utilise la modélisation directe pour étudier les déplacements et champs de contraintes autour de zones faillées complexes. On montre que l'ajout de contraintes inégalitaires, telles que la friction de Coulomb, permet d'expliquer l'angle d'initiation des dominos dans les relais extensifs. L'ajout de matériaux hétérogènes et d'optimisations, telles la parallélisation sur processeurs multi-coeurs ainsi que la réduction de complexité des modèles, permettent l'étude de modèles beaucoup plus complexes. Le second type de code numérique utilise la modélisation inverse, aussi appelée estimation de paramètres. L'inversion linéaire de déplacements sur les failles ainsi que la détermination de paléo-contraintes utilisant une approche géomécanique sont développées. Le dernier type de code numérique concerne la restauration de structures complexes plissées et faillées. Il est notamment montré qu'une telle méthode permet de vérifier l'équilibre de coupes géologiques, ainsi que de retrouver la chronologie des failles. Finalement, nous montrons que ce même code permet de lisser des horizons 3D faillés, plissés et bruités en utilisant la géomécanique.
https://tel.archives-ouvertes.fr/tel-00537899

tel-00537899
https://tel.archives-ouvertes.fr/tel-00537899
https://tel.archives-ouvertes.fr/tel-00537899/document
https://tel.archives-ouvertes.fr/tel-00537899/file/thesemaerten.pdf

Éditeur(s) : Innotermer, Brest, Novembre 1982
Résumé : Les échanges de Matériels vivants apparaissent comme une caractéristique constante de toute aquaculture, y compris de la conchyliculture traditionnelle. Ils interviennent par exemple sous forme d'animaux adultes mis sur le marché pour être consommés vivants, ou sous forme de naissain ou d'alevins d'importation, ou encore lors des essais d'acclimatation d'une espèce étrangère en vue de sa culture. A cela s'ajoutent les transferts au cours du développement : c'est ce dernier aspect qui retiendra surtout notre attention. Dans la mesure où l'aquaculture nouvelle cherche à maîtriser tous les stades du développement de l'œuf à l'adulte, les échanges ou transferts d'animaux vivants deviennent obligatoires : en effet, on ne saurait réaliser au même endroit l'élevage de larves pélagiques et celui des adultes. Ces échanges constituent le plus souvent une pierre d'achoppement car ils nécessitent des passages soit hors d'eau, soit dans des enceintes de taille réduite, ce qui provoque un stress sur les animaux manipulés. Mais inversement, la réussite technique de ces échanges est un gage de progrès en aquaculture. Pour illustrer ce problème, nous examinerons deux produits de caractéristiques différentes : les mollusques et les poissons.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00049/16001/13446.pdf
http://archimer.ifremer.fr/doc/00049/16001/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We review the evolution of concepts on and methods of estimating the state of stress from fault movements. Theories of failure in isotropic materials suggested a simple geometrical construction of optimal principal stress directions from a fault plane and its associated slip. These optimal directions align shear stress and slip directions and maximize the difference between shear stress and frictional resistance on the fault plane. Optimal stress directions for calcite twinning are obtained by a similar construction, with the difference that they maximize shear stress. Force representation of seismic sources independently introduced pressure, P, and tension, T, axes at positions that also maximize shear stress on both nodal planes. Frictional slip theory and the constraint that slip and shear stress directions be parallel allowed to address reactivation of pre-existing faults. This suggested that stress could also be inverted from reactivated fault and slip data or earthquake focal mechanisms. Early methods relied on geometrical constructions as a substitute for calculations, whereas later methods relied on software as these calculations became tractable with the help of computers. Similar methods were developed for the inversion of stress from crystal twin gliding with non-optimal geometry, with a different criterion that relies on a threshold of the component of shear stress along the gliding line. Even though these methods seek a common stress tensor compatible with fault and slip data, their main use is to separate polyphase data into homogeneous subsets and help deciphering complex tectonic histories. Fault and slip data can also be analyzed to constrain the strain rather than the stress tensor. In most cases this involves a summation and yields an average strain for the considered rock volume. Stress inversion thus appears better suited for differentiating heterogeneous data whereas strain analysis appears better suited for homogenizing them.
ISSN: 0040-1951

hal-00759043
https://hal.archives-ouvertes.fr/hal-00759043
DOI : 10.1016/j.tecto.2012.02.009

Résumé : En 2013, Le Groupe d'experts Intergouvernemental sur l'Evolution du Climat (GIEC) publie son cinquième rapport concernant les changements climatiques. Il y est souligné que le réchauffement climatique est sans équivoque, et que de nouvelles émissions de gaz à effet de serre impliqueront une poursuite du réchauffement et des changements affectant toutes les composantes du système climatique. En région tropicale, une hausse de la température, ainsi qu'une intensification des événements de sécheresse et de pluviométrie extrêmes sont à prévoir. C'est dans ce contexte que s'inscrit ce travail, dont le but est d'étudier la réponse de la forêt tropicale à ces changements climatiques prédits en Guyane Française. Pour ce faire, j'ai utilisé les données du dispositif de suivi forestier de Paracou pour construire un modèle de dynamique individuel basé sur les traits fonctionnels des arbres. Un modèle de mortalité a d'abord été réalisé puis couplé à un modèle de croissance.Le modèle couplé ainsi construit permet de modéliser la croissance et la mortalité des arbres sur un pas de temps de 2 ans tout en tenant compte de leur ontogénie et de leurs traits fonctionnels. Ce modèle a d'abord été appliqué aux essences commerciales de Guyane Française en forêt naturelle et exploitée en y ajoutant un indice de stress hydrique. Ceci permet de montrer que le stress hydrique fait baisser la croissance et augmenter la mortalité, tandis que l'exploitation a l'effet inverse. Malgré le signal commun, différentes réponses sont observées selon les espèces. Le modèle a ensuite été appliqué à la communauté en forêt naturelle pour identifier les drivers climatiques et les processus impactés. Il ressort que la croissance est impactée par le stress hydrique et la température, et que la mortalité est impactée par le stress hydrique et la pluviométrie totale.Ces résultats ont enfin permis de construire un modèle complet de dynamique forestière climat dépendant, et de simuler l'évolution d'une communauté pendant un siècle selon différents scénarios correspondant aux prédictions du GIEC. Les simulations mettent en évidence une très forte diminution de la croissance, ainsi qu'une plus faible diminution de la mortalité. Ceci entraine une diminution notable de la surface terrière, du diamètre quadratique et de la biomasse fraiche. Une analyse de sensibilité montre que ces changements sont principalement dus à l'augmentation sévère des températures prédites pour le siècle à venir. Des pistes de réflexion sur les enjeux de modélisation et les échelles considérées sont proposées en discussion de ce travail.
In 2013 the intergovernmental panel on climate change (ipcc) publishes its fifth report. This report underlines that an increase of temperature and a strengthening of drought and extreme rainfall are expected in tropical regions. This work was made in this context of climate changes, and aimed to study the response of the rainforest to predicted climate changes. To do this, i used the data from the study site of Paracou French Guiana to build an individual based dynamics model based on the functional traits of trees. This model was first applied to species with a commercial interest in French Guiana, in natural and logged forest and adding a water stress index as predictor. Water stress decreases growth and increases mortality, while logging had the opposite effect. The model was then applied to the community in natural forest for identifying potential climate drivers and impacted processes. Growth is impacted by the water stress and temperature and mortality is imp acted by the water stress and the total rainfall. These results allowed us to build a climate dependent model of forest dynamics and to run simulations of the evolution of a community under different scenarios for the next century. Simulations showed a decrease of growth and a small decrease of mortality. This resulted in a substantial decrease of basal area, squared diameter and fresh biomass.

http://www.theses.fr/2014AGUY0802/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Four decades after their introduction, the validity of fault slip inversion methods based on Wallace (1951) and Bott (1959) hypothesis, which states that the slip on each fault surface has the same direction and sense as the maximum resolved shear stress, is still a subject of debate. According to some authors, this hypothesis is questionable since fault mechanical interactions induce slip reorientations as confirmed by geomechanical models. This leads us to ask as to what extent the Wallace-Bott simplifications are reliable as a basis hypothesis for stress inversion from fault slip data. In this paper, we compare two inversion methods; the first is based on the Wallace-Bott hypothesis, and the second relies on geomechanics and mechanical effects on fault heterogeneous slip distribution. In that context, a multi-parametric stress inversion study covering (i) the friction coefficients (μ), (ii) the full range of Andersonian state of stress and (iii) slip data sampling along the faults is performed. For each tested parameter, the results of the mechanical stress inversion and the Wallace-Bott (WB) based stress inversion for slip are compared in order to understand their respective effects. The predicted discrepancy between the solutions of both stress inversion methods (based on WB and mechanics) will then be used to explain the stress inversions results for the chimney Rock case study. It is shown that a high solution discrepancy is not always correlated with the misfit angle (ω ) and can be found under specific configurations (View the MathML sourceR−, θ, μ, geometry) invalidating the WB solutions. We conclude that in most cases the mechanical stress inversion and the WB based stress inversion are both valid and complementary depending on the fault friction. Some exceptions (i.e. low fault friction, simple fault geometry and pure regimes) that may lead to wrong WB based stress inversion solutions are highlighted.
ISSN: 0040-1951

hal-01467165
https://hal.archives-ouvertes.fr/hal-01467165
DOI : 10.1016/j.tecto.2016.11.039

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wallace (1951) and Bott (1959) were the first to introduce the idea that the slip on each fault surface has the same direction and sense as the maximum shear stress resolved on that surface. However, this simplified hypothesis is questionable since fault mechanical interactions may induce slip reorientations. Earlier numerical geomechanical models confirmed that the slickenlines (slip vectors) are not necessarily parallel to the maximum resolved shear stress but are consistent with local stress perturbations. This leads us to ask as to what extent the Wallace and Bott simplifications are reliable as a basis hypothesis for stress inversion from fault slip data. Here, a geomechanical multi-parametric study using a 3D boundary element method, covering (i) fault geometries such as intersected faults or corrugated fault surfaces, (ii) the full range of Andersonian state of stress, (iii) fault friction, (iv) fault fluid pressure, (v) half space effect and (vi), rock properties, is performed in order to understand the effect of each parameter on the misfit angle between geomechanical slip vectors and the resolved shear stresses. It is shown that significant misfit angles can be found under specific configurations invalidating the Wallace and Bott assumptions, even though fault friction tends to minimize the misfit. We therefore conclude that in such cases, stress inversions based on fault slip data should be interpreted with care.
ISSN: 0040-1951

hal-01218418
https://hal.archives-ouvertes.fr/hal-01218418
DOI : 10.1016/j.tecto.2015.06.030

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy P - Oxford Open Option A Oxford University Press (OUP)
Résumé : International audience
The Pyrenean mountain range is a slowly deforming belt with continuous and moderate seismic activity. To quantify its deformation field, we present the velocity field estimated from a GPS survey of the Pyrenees spanning 18 yr. The PotSis and ResPyr networks, including a total of 85 GPS sites, were installed and first measured in 1992 and 1995–1997, respectively, and remeasured in 2008 and 2010. We obtain a deformation field with velocities less than 1 mm yr−1 across the range. The estimated velocities for individual stations do not differ significantly from zero with 95 per cent confidence. Even so, we estimate a maximum extensional horizontal strain rate of 2.0 ± 1.7 nanostrain per year in a N–S direction in the western part of the range. We do not interpret the vertical displacements due to their large uncertainties. In order to compare the horizontal strain rates with the seismic activity, we analyse a set of 194 focal mechanisms using three methods: (i) the ‘r’ factor relating their P and T axes, (ii) the stress tensors obtained by fault slip inversion and (iii) the strain-rate tensors. Stress and strain-rate tensors are estimated for: (i) the whole data set, (ii) the eastern and western parts of the range separately, and (iii) eight zones, which are defined based on the seismicity and the tectonic patterns of the Pyrenees. Each of these analyses reveals a lateral variation of the deformation style from compression and extension in the east to extension and strike-slip in the west of the range. Although the horizontal components of the strain-rate tensors estimated from the seismic data are slightly smaller in magnitude than those computed from the GPS velocity field, they are consistent within the 2σ uncertainties. Furthermore, the orientations of their principal axes agree with the mapped active faults.
ISSN: 0956-540X

hal-01171752
https://hal.archives-ouvertes.fr/hal-01171752
DOI : 10.1093/gji/ggv052

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : This paper presents an inversion method using the interseismic velocity field to determine effective rigidity of the lithosphere. The method is based on the minimization of a cost function defined as the quadratic measure of the difference between measured and modelled velocity fields on a discrete set of points. The continuous mapping of the rigidity is fulfilled with a limited set of parameters and the forward solution is achieved using a plane stress finite element code. The computation of the cost function gradient in the parameters' space allows one to iteratively find the best parameters set through a suitable optimization algorithm.;We first design a benchmark including an abrupt rigidity variation that cannot be described by a continuous function. For such a case, we show that increasing the number of parameters is a way to accurately describe sharp variations of the rigidity map. Then, we use a dense GPS velocity field over the southwestern United States to estimate the corresponding rigidity variations for different spatial resolutions of the parameters' grid. We analyse the conceptual and practical difficulties associated with our methodology. Finally, rigidity maps obtained by our inversion method in southwestern United States and particularly across the San Andreas Fault System are reviewed and compared to current plate rigidity estimates and geophysical data over this area.
ISSN: 0956-540X

hal-00669897
https://hal.archives-ouvertes.fr/hal-00669897
DOI : 10.1111/j.1365-246X.2011.05192.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In this paper, we describe an outcrop to characterize the effect of fracture spacing and type on larger scale effective elasticity, which is measured for the first time in-situ with a Schmidt hammer. The outcrop is dominated by lime mudstones and belongs to the deformation zone of the St Clement fault, in southern France. Our results suggest that small spacing of faults, open fractures and styolites leads to lesser effective Young's modulus, whereas small sealed fracture spacing leads to greater effective Young's modulus. These relationships are compatible with theoretical models of effective elasticity. Using Amadei and Savage (1993) approach, we define a non-linear model that relates Schmidt hammer rebound to spacing by fracture type. A hemisphere with a radius of 40 to similar to 200 cm is the rheological volume characterized by the Schmidt hammer. Results of model inversion demonstrate that variations of Schmidt hammer rebound over the outcrop can be used to estimate fracture type and stiffness. Stiffness of sealed fractures is 2-3 orders of magnitude greater than the stiffness of faults, stylolites and open fractures. This result is consistent with an increase of the rate of interseismic stress build-up of major faults with sealing of fractures in their damage zone.
ISSN: 0191-8141

hal-00669954
https://hal.archives-ouvertes.fr/hal-00669954
DOI : 10.1016/j.jsg.2011.09.009

Éditeur(s) : Amer Geophysical Union
Résumé : On November 21, 2004, a magnitude 6.3 earthquake occurred offshore, 10 km south of Les Saintes archipelago in Guadeloupe (French West Indies). There were more than 30000 aftershocks recorded in the following two years, most of them at shallow depth near the islands of the archipelago. The main shock and its main aftershock of February 14, 2005 (M-w = 5.8) ruptured a NE-dipping normal fault (Roseau fault), mapped and identified as active from high-resolution bathymetric data a few years before. This fault belongs to an arc-parallel en echelon fault system that follows the inner edge of the northern part of the Lesser Antilles arc, accommodating the sinistral component of oblique convergence between the North American and Caribbean plates. The distribution of aftershocks and damage (destruction and landslides) are consistent with the main fault plane location and attitude. The slip model of the main shock, obtained by inverting jointly global broadband and local strong motion records, is characterized by two main slip zones located 5 to 10 km to the SE and NW of the hypocenter. The main shock is shown to have increased the Coulomb stress at the tips of the ruptured plane by more than 4 bars where most of the aftershocks occurred, implying that failures on fault system were mainly promoted by static stress changes. The earthquake also had an effect on volcanic activity since the Boiling Lake in Dominica drained twice, probably as a result of the extensional strain induced by the earthquake and its main aftershock.
Journal Of Geophysical Research-solid Earth (0148-0227) (Amer Geophysical Union), 2011-10 , Vol. 116 , N. B10301 , P. 1-25

Droits : Copyright 2011 by the American Geophysical Union.
http://archimer.ifremer.fr/doc/00200/31099/29511.pdf
DOI:10.1029/2011JB008310
http://archimer.ifremer.fr/doc/00200/31099/

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
This paper investigates the orientation and sources of stress in the forearc of the Cascadia subduction zone in southwest British Columbia, using Bayesian inversion results from focal mechanism data and comparing results with GPS derived short-term strain rates. The subduction margin in this region includes a change in orientation from N-S in Washington State to NW-SE in British Columbia. Over 1000 focal mechanisms from North American crustal earthquakes have been calculated to identify the dominant style of faulting, and ∼600 were inverted to estimate the principal stress orientations and the stress ratio. Our results indicate the maximum horizontal compressive stress orientation changes with distance to the trench, from approximately margin-normal along the coast to approximately margin-parallel 100-150 km inland from the coast. Comparing stress orientations with GPS data, we relate the margin-normal stress direction to subduction-related strain rates due to the locked interface between the North American and Juan de Fuca plates just west of Vancouver Island. Further from the margin the plates are coupled less strongly, and the margin-parallel maximum horizontal compressive stress in the North American Plate relates to the northward push of the Oregon Block, which is also observed in the horizontal shortening direction of the residual strain rates, after the subduction component is removed.
ISSN: 0148-0227

hal-00853734
https://hal.archives-ouvertes.fr/hal-00853734
DOI : 10.1029/2010JB008003

Éditeur(s) : HAL CCSD Elsevier
Résumé : The relationship between deformation and so-called fluid paleotransfers in minor faults has been analysed in an argillaceous formation located in the Causses Basin in France. The fluid paleotransfers are related to the fault activity to a large extent. We attempt to estimate the intensity of paleo-deviatoric stress magnitudes under which the fault activity may have occurred and consequently, the change in the structural fault permeability. The paleo-deviatoric stress magnitudes were calculated with the inverse method of Etchecopar applied to calcite twinning. The measured crystals are contained within the core zone of minor faults and this study is based on a previous complete microtectonic and microstructural analysis of the faults. In this paper, analysis of calcite twinning has been applied for the first time to vein fillings associated small faults in a context of relatively weak deformation, a condition ensured by the tectonic and structural analysis. Calculation and discussion of the paleo-deviatoric stress tensors in relation to the evolution of the structural fault permeability and to the hydraulic behaviour of the faults are the aim of this paper. The analysed faults, created and active during the same tectonic event, were permeable under a (;σ;1;–;σ;3;) mean value of 40–50 MPa. On the other hand, the reactivation of faults during a second tectonic event implies mean (;σ;1;–;σ;3;) value higher than 40–50 MPa, especially for the faults that are poorly oriented with respect to the principal tectonic stress directions. The core zone of these faults remained sealed and impermeable or became permeable by development of microcracks inside the pre-existing fillings.
ISSN: 0040-1951

hal-00407577
https://hal.archives-ouvertes.fr/hal-00407577
DOI : 10.1016/j.tecto.2006.09.014

Éditeur(s) : HAL CCSD
Résumé : This study is designed to improve the understanding of structural, mechanical and petrophysical characteristics of deformation bands in porous sandstone such as their potential influence on fluid storage or migration in reservoir setting. Structural and petrophysical analysis of band networks from Provence show that permeability of band is mainly controlled by the degree of cataclasis and diagenetic processes at depth. Map-scale analysis of band networks underlines the major influence of tectonic regime on band distribution, organization and permeability. Band associated to normal-fault regime (cataclasis and low-permeability) are located around map-sclae-fault whereas band associated to thurst-fault regime (moderate cataclasis and permeability) are pervasively distributed in all the area. Reverse-sense band are cataclastic and low-permeabiilty around the Roquemaure thrust, which show the potential role of large-scale fault on structural and petrophysical characteristics of bands. This analysis also shows the influence of fault propagation on formation of low permeability catacastic bands. This analysis suggests also granulometry as factor controlling organization of band networks.A mechanical analysis of deformation bands is realized based on results from Provence. Yield envelopes of these materials are calculated from analytical solution. Triaxial tests done on sandstone (L'Etang quarry, Orange) confirm the shape of yield envelope theoretically calculated. Triaxial tests done on the poorly-lithified sands (Boncavaï quarry, Uchaux) show grain size, sorting and packing influencing yield envelope and cataclastic band localization at shallow burial depth. Stress paths are calculated for burial and tectonic event (extension and contraction) using the relationship between main stress and secondary stresses (K0) calibrated from well data. These different results are integrated into a model which allows to estimate type and structural characteristics of bands susceptible to form for a known geological setting.A structural, mechanical and petrophysical model is established form these results. This model is calibrated by permeability data from deformation bands of Provence and results from the mechanical model of strain localization. This model is also confronted to a synthesis of permeability data from literature, which confirms the influence of the different controlling parameters integrated to the model. This model is applied for two sites of uranium exploration/exploitation in porous sandstone reservoirs and validated by field observations.
Cette étude est destinée à améliorer la compréhension des caractéristiques structurales, pétrophysiques et mécaniques des bandes de déformation dans les grès poreux ainsi que de leur rôle potentiel sur la migration ou le piégeage des fluides en milieu réservoir. L'analyse structurale et pétrophysique des réseaux de bandes de Provence montre que leur perméabilité découle principalement de l'intensité de la cataclase dans leur microstructure et des processus diagénétiques qui peuvent s'y localiser avec la profondeur. L'analyse régionale de ces réseaux de bandes souligne l'influence majeure du régime tectonique sur leur distribution, leur organisation et leur perméabilité. Les bandes associées au régime normal (cataclactiques et peu perméables) sont localisées autour des failles cartographiques, tandis que les bandes associées au régime inverse (modérement cataclastiques et perméables) sont distribuées dans toute la région. Les bandes inverses sont fortement cataclastiques et imperméables uniquement autour du chevauchement de Roquemaure ce qui montre le rôle potentiel de la présence de grande faille sur les caractéristiques structurales et pétrophysiques de ces bandes. D'autre part, cette analyse suggère que la granulométrie de l'encaissant peut influencer l'initiation et l'organisation des réseaux. L'analyse mécanique des bandes de déformation a ensuite été réalisée à partir des résultats obtenus en Provence. L'enveloppe de plasticité de ces matériaux est calculée à l'aide d'une solution analytique. Les essais triaxiaux menés sur le grès de la carrière de l'Etang (orange) confirment la forme de ces enveloppes estimées théoriquement. Les essais réalisés sur les sables de Boncavaï (Uchaux) montrent que la taille des grains, le tri et de la compaction dans ces matériaux peu lithifiés influent sur leurs enveloppes de plasticité et la localisation des bandes cataclastiques à faibles profondeurs. Les trajets de contraintes sont estimés pour les phases d'enfouissement et de chargement tectonique (extension et compression) à partir de la relation entre contrainte principale et contraintes secondaires (K0), calibrée à partir de données de forage. Ces résultats sont intégrés à un modèle permettant d'estimer la nature et les caractéristiques structurales des bandes susceptibles de se former dans un contexte géologique donné. Un modèle structural, mécanique et pétrophysique a été établir à partir de ces différents résultats. Ce modèle est calibré à partir des données de perméabilité mesurées sur les bandes de Provence et des résultats du modèle mécanique de localisation cité précédemment. Ce modèle a ensuite été confronté à une synthèse des données de perméabilité disponibles dans la littérature et confirme l'influence des différents paramètres de contrôle pris en compte dans le modèle. Ce modèle a enfin pu être appliqué sur deux sites d'explorations/exploitations d'uranium en réservoir gréseux poreux et validé par les résultats obtenus, en concordance avec les observations de terrain.
https://tel.archives-ouvertes.fr/tel-01001389

NNT : 2013MON20067
tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389/document
https://tel.archives-ouvertes.fr/tel-01001389/file/36072_BALLAS_2013_archivage-1_cor.pdf

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Dehydration reactions result in minerals’ replacement and a transient fluid-filled porosity. These reactions involve interface-coupled dissolution–precipitation and might therefore lead to fixed crystallographic orientation relations between reactant (protolith) and product phases (i.e. topotaxy). We investigate these two phenomena in the dehydration of a foliated antigorite (atg) serpentinite by comparing the crystallographic preferred orientation (CPO) developed by olivine (ol), orthopyroxene (opx) and chlorite (chl) during high-pressure antigorite and chlorite dehydration in piston-cylinder experiments and in natural samples recording the dehydration of antigorite (Cerro del Almirez, Betic Cordillera, Spain). Experiments were performed under undrained conditions resulting in fluid-filled porosity and in strong CPO of the prograde minerals, controlled by the pre-existing antigorite CPO in the reactant foliated serpentinite. The orientation of a ol,opx and c∗chl is parallel to c∗atg from the protolith. The Cerro del Almirez samples show similar, locally well-developed topotactic relations between orthopyroxene, chlorite and antigorite, but the product CPOs are weaker and more complex at the thin section scale. In contrast to the experiments, olivine from natural samples shows a weak correlation between b ol and the former c∗atg. We relate the strengthening of local topotactic relations and the weakening of the inherited CPO at a larger scale in natural samples to compaction and associated fluid migration. Microstructural features that might be related to compaction in the natural samples include: (1) smooth bending of the former foliation, (2) gradual crystallographic misorientation (up to 16°) of prismatic orthopyroxene due to buckling by dislocation creep, (3) inversion of enstatite to low clinoenstatite (P21/c) along lamellae and (4) brittle fracturing of prismatic orthopyroxene enclosed by plastically deformed chlorite. The coexistence of orthopyroxene buckling and clinoenstatite lamellae enables estimating the local strain rates and shear stresses generated during compaction. An lower bound for the strain rates in the order of 10−12 to 10−13 s−1 and shear stresses of 60–70 MPa are estimated based on creep data. Lower shear stresses (20–40 MPa) are retrieved using a theoretical approach. These data point to slow compaction (and fluid extraction) in nature if the system is not perturbed by external forces, with rates only marginally higher than the viscoplastic deformation of the solid matrix.
ISSN: 0010-7999

hal-01174158
https://hal.archives-ouvertes.fr/hal-01174158
DOI : 10.1007/s00410-015-1129-4

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
AIM: To assess the effects of iron removal on cytochrome P450 2E1 activity and oxidative stress in dysmetabolic iron overload syndrome. METHODS: Forty-eight patients were randomized to phlebotomy therapy consisting of removal of 300-500 mL of blood every 14 days until serum ferritin levels dropped under 100 microg/L or to follow-up without phlebotomy therapy. Cytochrome P450 2E1 activity was measured at baseline and at the end of treatment by using the 6-hydroxychlorzoxazone/chlorzoxazone blood metabolic ratio, 2 h after the intake of 500 mg of chlorzoxazone. RESULTS: In the treatment group, a mean of 3.9 +/- 1.3 L of blood was removed and serum ferritin levels dropped from 715 +/- 397 to 74 +/- 34 microg/L. Variation of cytochrome P450 2E1 activity was not significantly different between the 2 groups (0.07 +/- 0.26 vs. 0.03 +/- 0.19, P = 0.36). In the treatment group, low-density lipoprotein cholesterol and vitamin E were lowered after treatment compared with control group (-0.15 +/- 0.51 vs. 0.24 +/- 0.58, P = 0.002 and -1.3 +/- 4.4 vs. 2.3 +/- 5.2, P = 0.03, respectively). Inversely, vitamin C was increased (0.5 +/- 3.5 vs. -1.8 +/- 3.9, P = 0.03). CONCLUSIONS: In dysmetabolic iron overload syndrome, reduction of iron stores does not significantly influence cytochrome P450 2E1 activity but is associated with a significant decrease of low-density lipoprotein cholesterol, suggesting that venesection therapy may be a suitable option in these patients.
ISSN: 0269-2813

hal-00702125
https://hal.archives-ouvertes.fr/hal-00702125
DOI : 10.1111/j.1365-2036.2006.03116.x
PUBMED : 17014579

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Peel splitting is a major physiological disorder affecting post-harvest banana quality. This phenomenon occurs only 3-6 days after ripening induction in specific cultivars such as cv. 925 when stored in saturating humidity conditions. In these conditions, Cavendish cultivars (Grande Naine, cv. GN) are not susceptible to splitting. Cvs. 925 and GN were thus investigated to detect possible determinants associated with splitting. Splitting intensity was tentatively found to be associated with an inverse water flux at high relative humidity (RH) through an osmotic peel to pulp water flux resulting from the higher sugar content in the pulp than in the peel. Rheological properties were measured, and although the peel resistance and elasticity in cv. 925 were surprisingly higher than in cv. GN, saturating humidity conditions (100 % RH) substantially reduced the peel resistance. However, the peel epicuticular wax in cv. 925 was clearly thinner than that in cv. GN, thus leading to limitation of peel hydration in cv. GN. Peel splitting in cv. 925 was also associated with a boost in respiration, an increase in oxidative stress markers (H2O2), resulting in an increase in cellular damage markers (MDA, PEL). Overall, our results suggest that peel splitting at high RH in cv. 925 is related to fast decrease peel water content and the induction of high oxidative stress damage.
ISSN: 0137-5881

hal-01545907
https://hal.archives-ouvertes.fr/hal-01545907
DOI : 10.1007/s11738-016-2253-0

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The interseismic velocity field provided by geodetic methods is generally interpreted in the framework of a thick elastic lithosphere with a slipping fault at depth. Because lateral variations of lithospheric rheology play a key role in determining the geological strain distribution, I examine the idea that interseismic strain rate variations also occur in response to lateral variations in the elastic thickness of the lithosphere. Using a stress balance principle and some simplifying assumptions, I show using a 1D model that elastic thickness is inversely proportional to strain rate for the simple case of pure strike-slip faulting. Elastic thickness computed on three profiles crossing the San Andreas fault system (SAFS) suggests that the distribution of interseismic strain rate is compatible with a thick elastic lithosphere in the Great Basin-Sierra Nevada province and on the Pacific plate. Conversely, a thin plate with a shallow asthenosphere is needed on the SAFS to explain its high strain rate. A 2.5D Finite Element model of interseismic strain in the Carrizo Plain region in Central California shows how known vertical and horizontal variations of elastic properties refine 1D model predictions. In a case of a multiple fault system, I point out that the interseismic velocity is not causally tied to faults slip rate. Therefore, analysing the velocity field across the SAFS cannot reliably provide faults slip rate distribution as previously claimed. Rather, the apparent correlation between geologic slip rate and interseismic strain may only indicate that the elastic thickness plays a dominant role in controlling fault strength. Finally, I suggest that interseismic geodetic strain could be a new way to infer effective elastic plate thickness on the continents.
ISSN: 0012-821X

hal-00412155
https://hal.archives-ouvertes.fr/hal-00412155
DOI : 10.1016/j.epsl.2008.01.046

Éditeur(s) : HAL CCSD
Résumé : International audience
Sub-continental lithospheric mantle rocks are exhumed at the foot of magma-poor distal passive margins as aresponse to extreme stretching of the continental crust during plate separation. Remnants of the Northern Iberianpaleo-passive margin are now exposed in the North-Pyrenean Zone (NPZ) and represent field analogues to studythe processes of continental crust thinning and subcontinental mantle exhumation. The NPZ results from theinversion of basins opened between the Iberia and Europa plates during Albo-Cenomanian times. In the westernNPZ, the ‘Chaînons Béarnais’ ranges display a fold-and-thrust structure involving the Mesozoic sedimentarycover, decoupled from its continental basement and associated with peridotite bodies in tectonic contact withPalaeozoic basement lenses of small size. Continental extension developed under hot thermal conditions, asdemonstrated by the syn-metamorphic Cretaceous ductile deformation affecting both the crustal basement and theallochthonous Mesozoic cover.In this study, we present structural and geochemical data providing constraints to reconstruct the evolution ofthe northern Iberia paleo-margin. Field work confirms that the pre-rift Mesozoic cover is intimately associatedto mantle rocks and to thin tectonic lenses of crustal basement. It also shows that the pre-rift cover was detachedfrom its bedrock at the Keuper evaporites level and was welded to mantle rocks during their exhumation atthe foot of the hyper-extended margin. The crust/mantle detachment fault is a major shear zone characterizedby anastomosed shear bands defining a plurimetric phacoidal fabric at the top of the serpentinized mantle. Thedetachment is marked by a layer of metasomatic rocks, locally 20 meters thick, made of talc-chlorite-pyrite-richrocks that developped under greenschist facies conditions. Raman Spectroscopy on Carbonaceous Materials(RSCM), performed on the Mesozoic cover reveal that the entire sedimentary pile underwent temperatures rangingbetween 200C and 480C.We show that: (i) at the site of mantle rocks exhumation, the boudinaged pre-rift sediments have undergone drasticsyn-metamorphic thinning with the genesis of a S0/S1 foliation and, (ii) the Paleozoic basement has been ductilelydeformed, into thin tectonic lenses that remained welded to the exhumed mantle rocks. Therefore the overallcrustal rheology appears dominated by shallow levels having a ductile behavior. This rheology is related to thepresence of a thick pre- and syn-rift decoupled cover acting as an efficient thermal blanket. This new geologicaldata set highlights important characteristics of ductile-type hyper-extended passive margin that cannot be obtainedfrom the study of seismic lines. Finally, we stress that studying field analogues represents a major tool to betterunderstand the mechanisms of extreme crustal thinning associated with mantle exhumation and their structuralinheritance during tectonic inversion.
Geophysical Research Abstracts
Vienne, Austria

insu-01510103
https://hal-insu.archives-ouvertes.fr/insu-01510103