Éditeur(s) : HAL CCSD Fayard/Arthème
Résumé : La biomécanique des plantes est née d'une approche interdisciplinaire. Elle regroupe ainsi des biologistes, des forestiers ou des agronomes, et des mécaniciens (des matériaux et des structures et plus récemment des fluides). Elle s'intéresse à la façon dont les plantes se portent et croissent. En particulier comment les plantes terrestres croissent en hauteur " contre " la gravité et dans le vent ; mais aussi comment les plantes aquatiques et les algues se développent dans les courants.
Aux Origines des Plantes

hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935/document
https://hal.archives-ouvertes.fr/hal-00795935/file/BiomA_canique_plantes_Fournier_Moulia_Gril.pdf

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
In the dense tropical rainforest understorey, saplings exhibit different growth strategies aiming at reaching light levels better fitting their ecology. Investing mainly in height growth, at the expense of their width, a lot are close to mechanical instability. Tachigali melinonii, a long living heliophilic tree species, is frequently observed to be extremely slender and supported by neighbours. Such observations suggest an active growth control through the perception of mechanical environment. * Mechanical environment or light availability, which one is the most influent on growth and slenderness (H/D)? To test this question, we recorded growth of control and staked saplings of two species with contrasting habits and ecology: T. melinonii, and Dicorynia guianensis, along a natural light gradient. * Dicorynia, the more stable, responded more clearly to the staking treatment, showing slenderness increase when light is available, whereas for Tachigali, only light availability governed growth. * For Tachigali, growth allocation is mainly governed by light availability and ontogeny, whereas Dicorynia is probably similar to the average tree strategy, using the thigmomorphogenetic physiological process to control its stability.
ISSN: 1286-4560

hal-00534019
https://hal.archives-ouvertes.fr/hal-00534019
DOI : 10.1051/forest/2009104

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
This study aims at better understanding the respective influences of specific gravity (γ), microfibril angle (MFA), and cell-wall matrix polymers on viscoelastic vibrational properties of wood in axial direction. The wide variations of properties between normal wood (NW) and compression wood (CW) are in focus. Three young bent trees (Picea abies, Pinus sylvestris and Pinus pinaster) that recovered verticality were sampled. Several observed differences between NW and CW were highly significant in terms of anatomical, physical (γ, shrinkage, CIELab colorimetry), mechanical (compressive strength), and vibrational properties. Specific dynamic modulus of elasticity (E'/γ) decreases with increasing MFA, and Young's modulus (E') can be satisfactorily explained by γ and MFA. Apparently, the type of the cell wall polymer matrix is not influential in this regard. The damping coefficient (tanδ) does not depend solely on MFA of NW and CW. The tanδ - E'/γ relationship evidences that, at equivalent E'/γ, the tanδ of CW is approx. 34% lower than that of NW. This observation is ascribed to the more condensed nature of CW lignins, and this is discussed in the context of previous findings in other hygrothermal and time/frequency domains. It is proposed that the lignin structure and the amount and type of extractives, which are both different in various species, are partly responsible for taxonomy-related damping characteristics.
ISSN: 0018-3830

hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062/document
https://hal.archives-ouvertes.fr/hal-00808062/file/Changes_viscoelastic_vibrational_Bremaud_al.pdf
DOI : 10.1515/hf-2011-0186

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A feasibility study of glulam was carried out in French Guiana using local wood species. The aim was to determine gluing parameters affording satisfactory behaviour to manufactured glulam in a tropical climate. Three abundant wood species, with special properties, were selected for the study and Resorcinol-Phenol-Formaldehyde resin was used for bonding. Three industrial parameters were considered: adhesive spread rate, closed assembly time and gluing pressure. Delamination and shearing tests were carried outin accordance with European Standards. The tests revealed the influence of wood properties and manufacturing parameters on joint resistance. In fact, the results showed that specific gravity and the shrinkage coefficientgreatly influenced the gluing step. Indeed, wood with a medium specific gravity needed more adhesive and more pressure than wood with a high specific gravity. In addition, planning and lamella thicknesswere found to affect glue joint resistance.
ISSN: 0018-3768

hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933/document
https://hal.archives-ouvertes.fr/hal-00856933/file/Feasibility_glued_laminated_timber_Bourreau_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
In order to progress in the understanding of mechanical stress generation, the mesoporosity of the cell wall and its changes during maturation of poplar (Populus deltoides x P. nigra) tension wood (TW) and opposite wood (OW) were measured by nitrogen adsorption–desorption. Variations in the thickness of the gelatinous layer (G-layer) were also measured to clarify whether the mesoporosity change simultaneously with the deposition of the G-layer in TW. Results show that mesoporous structures of TW and OW were very similar in early development stages before the deposition of G-layers. With the formation of the S2 layer in OW and the G-layer in TW, the mesopore volume decreased steeply before lignification. However, in TW only, the decrease in mesopore volume occurred together with the pore shape change and a progressive increase in pore size. The different patterns observed in TW revealed that pores from G-layers appear with a different shape compared to those of the compound middle lamella, and their size increases duringthe maturation process until stabilising in mature wood. This observation strongly supports the hypothesis of the swelling of the G-layer matrix during maturation as the origin of maturation stress in poplar tension wood.
ISSN: 0028-646X

hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834/document
https://hal.archives-ouvertes.fr/hal-01081834/file/Chang_al_Mesoporosity_changes_New-Phyto._2015.pdf
DOI : 10.1111/nph.13126

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Radial trends of vibrational properties, including the specific dynamic modulus (E'/r) and damping coefficient (tand), were investigated for 3 tropical rainforest hardwood species, Simarouba amara, Carapa procera and Symphonia globulifera by free-free flexural vibration test. The microfibril angle (MFA) was estimated through X-Ray diffraction. Consistent patterns of radial variations were observed for all studied properties. E'/r was found to decrease from pith to bark, which is strongly related to the increasing pith-bark trend of MFA. The variation of tand along the radius can be partly explained by MFA, and partly by the gradient of extractives due to heartwood formation. The coupling effect of MFA and extractives could be separated through the analysis of log(tand) - log(E'/r) diagram. For the studied species, the extractive content putatively associated to heartwood formation generally tends to decrease the wood damping coefficient. However, this weakening effect of extractives was not observed for inner part of the heartwood, suggesting the mechanical action of extractives was reduced during their chemical ageing.
ISSN: 1435-0211

hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055/document
https://hal.archives-ouvertes.fr/hal-00797055/file/Radial_variations_vibrational_Zhang_al.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
The main biological function of reaction wood is to act as “muscle” for trees, enabling them to control their posture and right stems when they are permanently disturbed from their set-point inclination by gravity or winds. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called “maturation strains”. Moreover, this function is basically performed through the asymmetric formation of wood (in quantity or quality) around the tree circumference. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity, as an asymmetric force associated to maturation strains creates a bending moment (i.e. one side of the stem “pulls” the other one). We will discuss the traits (cross sectional size and shape, wood features as G fibers or microfibril angle, eccentric growth even in usual or extreme cases as buttresses, total biomass growth and height of center of mass, stem lean and set-point angle) involved to understand how the posture control works. We will give simple formulas to estimate a “muscle efficiency” from biomechanical modeling. We will give practical methods to estimate all the involved traits, especially maturation strains from direct and indirect measurements, in peripheral functional wood or by retrospective dendrochronological analysis. Then, we will illustrate how tree stem tropisms and especially gravitropism, widely studied by physiologists, are key processes in natural ecosystems, through practical examples from tropical rainforest tree communities and regeneration of European mixed beech forests. Using the previous definition of postural control efficiency, we will show that the cross section size is rapidly a limiting factor, opposing the extreme strategies of flexible small stems, which bend easily but also right themselves quickly, to stiff big stems. Lastly, as wood in living trees ensures general storage, defence, vascular and skeletal functions, we will ask general questions about synergies and trade-offs between posture control and other functions.
Botany 2014 : new frontiers in botany
Boise, United States

hal-01627031
https://hal.archives-ouvertes.fr/hal-01627031

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0

Éditeur(s) : HAL CCSD
Résumé : International audience
Some morphological and biochemical taxonomic markers are also affecting factors of dynamic mechanical properties of wood. Thus, could these properties reflect the classification/phylogeny of taxa? This work is a first insight into this question. It relied on the gathering (through experimental campaigns and exhaustive literature review) of a large database on the viscoelastic (i.e. including damping) vibrational properties of 445 woody species. relationship between damping was confirmed at a wide interspecific scale, but described no more than 40% of not in a way that could be easily related to the phylogenetic tree. Damping was a bit more -Papilionoideae and, to a lesser extent, Lauraceae, Cupressaceae and Moraceae) damping than average, independently While for some other families no clear characteristics could be observed at least with the present number of represented species. In the future, increasing the amount of data and compiling anatomical and chemical markers / affecting factors will allow further analysis at sub-family levels, and a better understanding of this wide topic.
6th Plant Biomechanics Conference PBM09
Cayenne, French Guiana

hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398/document
https://hal.archives-ouvertes.fr/hal-00808398/file/Mechanical_damping_wood_Bremaud_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Functional ecology has long considered the support function as important, but its biomechanical complexity is only just being elucidated. We show here that it can be described on the basis of four biomechanical traits, two safety traits against winds (SW) and self-buckling (SB), and two motricity traits involved in sustaining an upright position, tropic motion velocity (MV) and posture control (PC). All these traits are integrated at the tree scale, combining tree size and shape together with wood properties. The assumption of trait constancy has been used to derive allometric scaling laws, but it was more recently found that observing their variations among environments and functional groups, or during ontogeny, provides more insights into adaptive syndromes of tree shape and wood properties. However, over-simplified expressions have often been used, possibly concealing key adaptive drivers. An extreme case of over-simplification is the use of wood basic density as a proxy for safety. Actually, since wood density is involved in stiffness, loads and construction costs, the impact of its variations on safety is non-trivial. Moreover, other wood features, especially the microfibril angle (MFA), are also involved. Furthermore, wood is not only stiff and strong, but it also acts as a motor for MV and PC. The relevant wood trait for that is maturation strain asymmetry. Maturation strains vary with cell wall characteristics such as MFA, rather than with wood density. Finally, the need for further studies about the ecological relevance of branching patterns, motricity traits and growth responses to mechanical loads is discussed.
ISSN: 0022-0957

hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904/document
https://hal.archives-ouvertes.fr/hal-00909904/file/Integrative_biomechanics_for_tree_Fournier_al.pdf
DOI : 10.1093/jxb/ert279

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
International audience
The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three-dimensional strains were measured at different parts of the trunk base. Risks of failure were greater on the buttress sides, where shear and tangential stresses are greater, not on the ridges, in spite of high longitudinal (parallel to the grain) stresses. A simple beam model, computed from the second moment of area of digitized cross sections, is consistent with longitudinal strain variations but cannot predict accurately variations with height. Patterns of longitudinal strain variation along ridges are very different in the two individuals, owing to a pronounced lateral curvature in one specimen. The constant stress hypothesis is discussed based on these results. Without chronological data during the development of the tree, it cannot be proved that buttress formation is activated by stress or strain.
ISSN: 0002-9122

hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155/document
https://hal.archives-ouvertes.fr/hal-01032155/file/Biomechanics_buttressed_trees_Clair_al_2003.pdf
DOI : 10.3732/ajb.90.9.1349

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Studies on the periodicity of wood formation provide essential data on tree age and factors related to the control of tree growth. The aim of this work was to investigate the cambial phenology and its relation with leaf phenology and climatic seasonality in two tropical rainforest species belonging to the genus Parkia known for having a contrasted leaf phenology. From wood samples collected at 15 day intervals from April 2009 to February 2012 in five trees of both species, we quantified cambial activity by counting layers of cells in cambial zone, enlarging cells zone and wall thickening cells zone from wood prepared anatomical micro sections. In the same time, we observed leaf shedding behaviors in the crown of the studied trees. In both species, cambial activity was significantly reduced during leafless period. However, the cambial activity of P. velutina was not affected by seasonality while in P. nitida, we found a significant positive effect of the dry season on cambial activity. This diminution of activity associated to leaf shedding occurred annually during the dry season in P. nitida whereas the trees were not synchronous in time for P. velutina. On the contrary that is often admitted, the rest cambial period can be independent of environmental restriction such as dry season. Leaf phenology remains the best proxy to estimate cambial activity.
ISSN: 0931-1890

hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166/document
https://hal.archives-ouvertes.fr/hal-01135166/file/Art_Morel_al_Seasonal_variations_phenological_traits_2015.pdf
DOI : 10.1007/s00468-015-1177-4

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Studies on tree biomechanical design usually focus on stem stiffness, resistance to breakage or uprooting, and elastic stability. Here we consider another biomechanical constraint related to the interaction between growth and gravity. Because stems are slender structures and are never perfectly symmetric, the increase in tree mass always causes bending movements. Given the current mechanical design of trees, integration of these movements over time would ultimately lead to a weeping habit unless some gravitropic correction occurs. This correction is achieved by asymmetric internal forces induced during the maturation of new wood. The long-term stability of a growing stem therefore depends on how the gravitropic correction that is generated by diameter growth balances the disturbance due to increasing self weight. General mechanical formulations based on beam theory are proposed to model these phenomena. The rates of disturbance and correction associated with a growth increment are deduced and expressed as a function of elementary traits of stem morphology, cross-section anatomy and wood properties. Evaluation of these traits using previously published data shows that the balance between the correction and the disturbance strongly depends on the efficiency of the gravitropic correction, which depends on the asymmetry of wood maturation strain, eccentric growth, and gradients in wood stiffness. By combining disturbance and correction rates, the gravitropic performance indicates the dynamics of stem bending during growth. It depends on stem biomechanical traits and dimensions. By analyzing dimensional effects, we show that the necessity for gravitropic correction might constrain stem allometric growth in the long-term. This constraint is compared to the requirement for elastic stability, showing that gravitropic performance limits the increase in height of tilted stem and branches. The performance of this function may thus limit the slenderness and lean of stems, and therefore the ability of the tree to capture light in a heterogeneous environment.
ISSN: 0022-5193

hal-00534316
https://hal.archives-ouvertes.fr/hal-00534316
DOI : 10.1016/j.jtbi.2008.10.011

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Extractives can affect vibrational properties tanδ (damping coefficient) and E'/ρ (specific Young's modulus) but this is highly dependent on species, compounds, and cellular locations. This paper investigates such effects for African Padauk (Pterocarpus soyauxii Taub.), a tropical hardwood with high extractives content and a preferred material for xylophones. 5 groups of 26 heartwood specimens with large, yet comparable, ranges in vibrational properties were extracted in different solvents. Changes in vibrational properties were set against yields of extracts and evaluation of their cellular location. Methanol (ME) reached most of compounds (13%), located about half in lumen and half in cell-wall. Water solubility was extremely low. tanδ and E'/ρ were very strongly related (R2≥0.93), but native wood had abnormally low values of tanδ, while extraction shifted this relation towards higher tanδ values. ME extracted heartwood became in agreement with the average of many species, and close to sapwood. Extractions increased tanδ as much as 60%, irrespective of minute moisture changes or of initial properties. Apparent E'/ρ was barely changed (+2% to -4%) but, after correcting the mass contribution of extracts, was in fact slightly reduced (down to -10% for high E'/ρ), and increasingly so for specimens with low initial values of E'/ρ.
ISSN: 0043-7719

hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236/document
https://hal.archives-ouvertes.fr/hal-00804236/file/Effect_extractives_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0337-3

Éditeur(s) : HAL CCSD American Physical Society
Résumé : International audience
We investigate a class of granular materials characterized by the possibility of interlocking between the particles. The interlocking is modeled by its effect through rolling resistance depending on relative rotation and normal force at the contact points and involving a single parameter analogous to the sliding friction coefficient. The model, which is introduced in the framework of the contact dynamics, method, is applied to simulate the simple shear of a large granular sample. We present a detailed analysis regarding the influence of rolling and sliding friction parameters on the macroscopic response in terms of shear strength, fabric properties, and force transmission. Interestingly, two distinct regimes can be distinguished in which the steady-state shear strength is controlled by either rolling resistance or sliding friction. The relative contributions of rolling and sliding contacts to the shear strength are consistent with the same two regimes. Interlocking strongly affects the force network by enhancing the arching effect and thus increasing the relative importance of weak contact forces and torques, which is reflected in a decreasing power-law probability distribution of the contact forces and torques below the mean. Due to the combined effect of friction and interlocking, the force-carrying backbone takes an increasingly columnar aspect involving a low fraction of particles. Our data suggest that the nature of the weak contact network is strongly affected by the formation of these columns of particles which do not need to be propped laterally. In particular, in the limit of high rolling resistance and sliding friction, the role of the weak network of contacts is no longer to prop the force chains, but, like the strong contact network, to actively sustain the deviatoric load imposed on the system.
ISSN: 1539-3755

hal-00412020
https://hal.archives-ouvertes.fr/hal-00412020
DOI : 10.1103/PhysRevE.78.021301

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD
Résumé : For their survival, plants need to grow in height to access light resource while ensuring their mechanical stability. Growth in height amplifies the mechanical constraints due to wind and gravity. Nevertheless these constraints represent morphogenetic signals that plants respond to by modifying their growth. There are two regulatory processes of growth by mechanical signals: thigmomorphogenesis and gravitropism. Thigmomorphogenesis expresses by a reduction of growth in height and an increase of growth in girth under the effect of mechanical signals. This is a way for plants to grow with controlling slenderness of their axes to avoid buckling (beating down). In some cases (storm, sudden exposure to a new mechanical environment) this process is not sufficient to prevent buckling, gravitropism then acts to restore axes orientation in case of no lethal buckling. With measuring several traits, we have demonstrated that these processes have a fundamental ecological role in the control of tree habit and the vertical structuration of ecosystems. As studies of climate changes seem to predict a higher frequency of storms it is important to study the diversity of their efficiency.
Colloque Adaptation au Changement Climatique de l'Agriculture et des Ecosystèmes

hal-00797377
https://hal.archives-ouvertes.fr/hal-00797377