Éditeur(s) : HAL CCSD Geological Society of America
Résumé : International audience
Porous sandstones tend to deform by the formation of low-permeability deformation bands that influence fluid flow in reservoir settings. The bands may be distributed or localized into clusters, and limited recent data suggest that tectonic regime may exert control on their distribution and clustering. In order to explore this suggestion, we performed a synthetic analysis based of 73 sets of bands, including 22 new sets measured for a reverse Andersonian regime that fill the important gap in data for this context. We find a surprisingly strong correlation between clustering and tectonic regime, where bands clearly are more distributed in the reverse regime compared to the normal regime. Together with the observed band distributions, capillary pressure data show evidence that efficient membrane seals are expected for extension, whereas pervasive permeability anisotropy is expected for contraction. Such a basic new rule concerning tectonic regime is very useful for assessment of reservoir properties where deformation bands are common but below seismic resolution.
ISSN: 0091-7613

hal-01355925
https://hal.archives-ouvertes.fr/hal-01355925
DOI : 10.1130/G37585.1

Éditeur(s) : HAL CCSD Pergamon
Résumé : This paper presents an experimental study of the deformation of Beaucaire marl subjected to drained triaxial tests under a wide range of confining pressure. Several methods of observation have been used: X-ray computed tomography, scanning electronic microscopy, quantitative image analysis of thin sections and mercury porosimetry. The analysis at the grain scale shows the existence of various deformation modes depending on the mean stress level. These modes are classified with reference to the brittle and ductile regimes. In specimens deformed under low confining pressure, macro-cracks are localised in a band more contracting than the rest of the specimen. In specimens deformed under moderate confining pressure, a series of micro-scale shear bands characterised by a grain re-orientation towards the direction of macro-shear is detected in the zones of localised deformation. The material in between the micro-scale shear bands is contracting more than the rest of the specimen in some cases; in other cases, a schistosity is detected also in the rest of the specimen outside the localisation zones. In the specimen deformed under high confining pressure, no localisation occurs, and a schistosity is observable throughout the specimen.
ISSN: 1365-1609

hal-00411208
https://hal.archives-ouvertes.fr/hal-00411208
DOI : 10.1016/j.ijrmms.2007.08.007

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Rifting in a cratonic lithosphere is strongly controlled by several interacting processes including crust/mantle rheology, magmatism, inherited structure and stress regime. In order to better understand how these physical parameters interact, a 2 yr long seismological experiment has been carried out in the North Tanzanian Divergence (NTD), at the southern tip of the eastern magmatic branch of the East African rift, where the southward-propagating continental rift is at its earliest stage. We analyse teleseismic data from 38 broad-band stations ca. 25 km spaced and present here results from their receiver function (RF) analysis. The crustal thickness and Vp/Vs ratio are retrieved over a ca. 200 × 200 km2 area encompassing the South Kenya magmatic rift, the NTD and the Ngorongoro-Kilimanjaro transverse volcanic chain. Cratonic nature of the lithosphere is clearly evinced through thick (up to ca. 40 km) homogeneous crust beneath the rift shoulders. Where rifting is present, Moho rises up to 27 km depth and the crust is strongly layered with clear velocity contrasts in the RF signal. The Vp/Vs ratio reaches its highest values (ca. 1.9) beneath volcanic edifices location and thinner crust, advocating for melting within the crust. We also clearly identify two major low-velocity zones (LVZs) within the NTD, one in the lower crust and the second in the upper part of the mantle. The first one starts at 15–18 km depth and correlates well with recent tomographic models. This LVZ does not always coexist with high Vp/Vs ratio, pleading for a supplementary source of velocity decrease, such as temperature or composition. At a greater depth of ca. 60 km, a mid-lithospheric discontinuity roughly mimics the step-like and symmetrically outward-dipping geometry of the Moho but with a more slanting direction (NE–SW) compared to the NS rift. By comparison with synthetic RF, we estimate the associated velocity reduction to be 8–9 per cent. We relate this interface to melt ponding, possibly favouring here deformation process such as grain-boundary sliding (EAGBS) due to lithospheric strain. Its geometry might have been controlled by inherited lithospheric fabrics and heterogeneous upper mantle structure. We evidence that crustal and mantle magmatic processes represent first order mechanisms to ease and locate the deformation during the first stage of a cratonic lithospheric breakup.
ISSN: 0956-540X

hal-01622078
https://hal.archives-ouvertes.fr/hal-01622078
https://hal.archives-ouvertes.fr/hal-01622078/document
https://hal.archives-ouvertes.fr/hal-01622078/file/plasmanGJI2017.pdf
DOI : 10.1093/gji/ggx177

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Upper-mantle flow beneath the South Pacific is investigated by analysing shear wave splitting parameters at eight permanent long-period and broad-band seismic stations and 10 broad-band stations deployed in French Polynesia from 2001 to 2005 in the framework of the Polynesian Lithosphere and Upper Mantle Experiment (PLUME). Despite the small number of eventsand the rather poor backazimuthal coverage due to the geographical distribution of the natural seismicity, upper-mantle seismic anisotropy has been detected at all stations except at Tahiti where two permanent stations with 15 yr of data show an apparent isotropy. The median value of fast polarization azimuths (N67.5°W) is parallel to the present Pacific absolute platemotion direction in French Polynesia (APM: N67°W). This suggests that the observed SKS fast polarization directions result mainly from olivine crystal preferred orientations produced by deformation in the sublithospheric mantle due to viscous entrainment by the moving Pacific Plate and preserved in the lithosphere as the plate cools. However, analysis of individualmeasurements highlights variations of splitting parameters with event backazimuth that imply an actual upper-mantle structure more complex than a single anisotropic layer with horizontal fast axis. A forward approach shows that a two-layer structure of anisotropy beneath French Polynesia better explains the splitting observations than a single anisotropic layer. Second ordervariations in the measurements may also indicate the presence of small-scale lateral heterogeneities. The influence of plumes or fracture zones within the studied area does not appear to dominate the large-scale anisotropy pattern but may explain these second-order splitting variations across the network.
ISSN: 0956-540X

hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275/document
https://hal.archives-ouvertes.fr/hal-01249275/file/GJI2007SKS.pdf
DOI : 10.1111/j.1365-246X.2007.03475.x

Éditeur(s) : HAL CCSD
Résumé : International audience
In most rock mechanical testing devices, the texture developed during deformation is only observed after the failure, and the detailed mapping of cracks and pore structure evolution, just before or after rupture, remains speculative. Computerized X-ray tomography (CT X-ray) offers a way to observe 'in vivo' some characteristics of a tested sample in the course of its deformation. Therefore we developed an X-ray transparent tri-axial cell that was included in a medical purpose X-ray scanner with a volumetric resolution of the order of 1 mm3. This technique is described and applied to a porous calcarenite, which is regularly scanned for porosity evolution during mechanical testing. The experiment is performed at low confining pressure (2-10 MPa). During testing, an axial load is applied until failure and is then progressively decreased. In these experiments, the peak stress is preceded by phase of diffuse dilatancy. After failure localization, the axial stress is unloaded until the stress reaches isotropy. During this unloading phase, the previous diffuse dilatancy is lost due to an elastic relaxation. Then, the stress is completely relaxed. At this moment the dilatancy increases again and the residual dilatancy is larger than that reached at the peak stress. When observed "post mortem" at microscopic scale, the dilatant structures are comprised of cataclastic deformation bands and cracks in some larger crystals.
International Journal of Rock Mechanics and Mining Science

hal-00767563
https://hal.archives-ouvertes.fr/hal-00767563
DOI : 10.1016/j.ijrmms.2012.07.020

Éditeur(s) : HAL CCSD Elsevier
Résumé : We studied the evolution of the microstructure of ice-Ih during static recrystallization by stepwise annealing experiments. We alternated thermal annealing and electron backscatter diffraction (EBSD) analyses on polycrystalline columnar ice pre-deformed in uniaxial compression at temperature of −7 °C to macroscopic strains of 3.0–5.2. Annealing experiments were carried out at −5 °C and −2 °C up to a maximum of 3.25 days, typically in 5–6 steps. EBSD crystal orientation maps obtained after each annealing step permit the description of microstructural changes. Decrease in average intragranular misorientation at the sample scale and modification of the misorientation across subgrain boundaries provide evidence for recovery from the earliest stages of annealing. This initial evolution is similar for all studied samples irrespective of their initial strain or annealing temperature. After an incubation period ≥1.5 h, recovery is accompanied by recrystallization (nucleation and grain boundary migration). Grain growth proceeds at the expense of domains with high intragranular misorientations, consuming first the most misorientated parts of primary grains. Grain growth kinetics fits the parabolic growth law with grain growth exponents in the range of 2.4–4.0. Deformation-induced tilt boundaries and kink bands may slow down grain boundary migration. They are stable features during early stages of static recrystallization, only erased by normal growth, which starts after >24 h of annealing.
ISSN: 0191-8141

hal-01685644
https://hal.archives-ouvertes.fr/hal-01685644
DOI : 10.1016/j.jsg.2017.05.001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
TEM Study of Heavitree quartzite deformed at high temperatures and a pressure of 1.5 GPa with three different preparations: water-added, vacuum dried, and sodium doped show a wide range of dislocation microstructure. The vacuum dried sample has a very heterogeneous dislocation distribution varying from almost no dislocations to very high densities. Dislocation nucleation occurs by cross-slip mechanisms, such as Frank-Read sources and Orowan loops around hard inclusions. Shear bands develop in the basal plane composed of two closely spaced shear planes. Dislocations have straight segments and they are aligned along directions of dense packing, suggesting strong Peierls stress control due to the crystal structure. No voids, bubbles or dislocation walls where observed in the vacuum dried sample. The sodium-doped sample had a homogeneous high dislocation density. The water-added sample has a significantly lower, relatively uniform dislocation density. Bubbles associated with dislocations are seen in every grain. Dislocations were either present in loops around bubbles or as straight dislocations with small bubbles spaced along the dislocation line. Some of the long straight dislocations are aligned parallel to the c-axis. Sub-grains where very frequent, sometimes form cells of about 2 p,m in diameter with straight edges. Analysis of dislocations show 1/3 < a > and [c] dislocations in sub-grain walls and free 1/3 < a > dislocations on prism planes. There is clear evidence for dislocation climb with sub-grain walls, dislocation cells, dislocation junctions and dislocation debris of small loops. The major difference between vacuum dried and water-added samples are the homogeneity of the microstructure and evidence for climb in the water-added sample. Glide is clearly difficult, with a high Peierls stress in the vacuum dried sample as shown by areas of very low and very high dislocation density and the crystallographic control of dislocation line direction. The sodium-doped sample indicates that nucleation was easy by the high homogenous dislocation density, but no climb recovery has taken place. The density is high and the dislocations are strongly interacting causing tangles; no evidence for crystallographic control can be observed at these levels of strain. The activation energy for creep in Heavitree quartzite decreases with inferred water content of the specimens form 185 kJ mol(-1) for vacuum dried to 151 for 0.4 wt% water-added samples. Analysis of diffusion data for oxygen under hydrothermal conditions and inferred diffusion data for the hydrogarnet defect and dislocation velocity suggests activation energies for these processes are similar to the activation energy for the dislocation creep of Heavitree quartzite and other quartz aggregates. For data from the previously published experiments with the highest stress resolution there is a correlation between the A pre-factor in the power law creep equation and the activation energy for creep. It is speculated that the correlation may be due to variable hydrogarnet defect concentrations.
ISSN: 0031-9201

hal-00413112
https://hal.archives-ouvertes.fr/hal-00413112
DOI : 10.1016/j.pepi.2008.07.009

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We report structural evidence of ductile strain localization in mantle pyroxenite from the spinel to plagioclase websterite transition in the Ronda Peridotite (southern Spain). Mapping shows that, in this domain, small-scale shear zones occurring at the base of the lithospheric section are systematically located within thin pyroxenite layers, suggesting that the pyroxenite was locally weaker than the host peridotite. Strain localization is associated with a sudden decrease of grain size and increasing volume fractions of plagioclase and amphibole as a result of a spinel to plagioclase phase transformation reaction during decompression. This reaction also fostered hydrogen extraction ('dehydroxylation') from clinopyroxene producing effective fluid saturation that catalyzed the synkinematic net-transfer reaction. This reaction produced fine-grained olivine and plagioclase, allowing the onset of grain-size sensitive creep and further strain localization in these pyroxenite bands. The strain localization in the pyroxenites is thus explained by their more fertile composition, which allowed earlier onset of the phase transition reactions. Geothermobarometry undertaken on compositionally zoned constituent minerals suggests that this positive feedback between reactions and deformation is associated with cooling from at least 1000°C to 700°C and decompression from 1*0 to 0*5 GPa.
ISSN: 0022-3530

hal-00941293
https://hal.archives-ouvertes.fr/hal-00941293
DOI : 10.1093/petrology/egt039

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The 40Ar/39Ar geochronological technique has significantly contributed to the study of crustal deformation. However, the frequent occurrence of extraneous argon in high-pressure terrains can make the interpretation of 40Ar/39Ar ages problematic. This contribution attempts to: i) characterize the distribution and origin of extraneous argon in the Cycladic Blueschist Unit (CBU, Greece) by applying the 40Ar/39Ar dating technique on three Cycladic islands, Syros, Tinos and Ios, which span a complete transect of the CBU and ii) discuss regional implications for the tectonometamorphic evolution of the CBU. Our results, combined with ages available in the literature, show that periods of peak-burial conditions (55–49 Ma) and syn- (45–38 Ma) to post-orogenic exhumation (37–21 Ma) are well constrained in the CBU by the 40Ar/39Ar method. Moreover, Variscan apparent ages are preserved in the Cycladic basement of Ios, indicating that the 40Ar/39Ar system was not completely reset during the Eocene metamorphic episode. Additionally, our 40Ar/39Ar data show that the occurrence of extraneous argon is heterogeneously distributed in the CBU. While high-pressure rocks of Syros and Tinos are only locally affected, extraneous argon is clearly evidenced in the CBU of Ios, yielding geologically meaningless ages up to 900 Ma. On each island, the most affected ages were obtained in microstructures where fluid circulation is enhanced such as shear bands or strain shadows around garnets. We suggest that the Cycladic Basement, a polymetamorphic continental unit, behaved as an argon reservoir that has been mobilized by fluid circulation at the Eocene. These argon-enriched fluids have then heterogeneously contaminated metamorphic rocks when percolating through the CBU. Finally, we claim that a minimum closure temperature of 550 °C must be accepted for the phengites of the CBU and conclude that volume diffusion is not the main process resetting the argon isotopic system in high-pressure rocks compare to recrystallization enhanced by fluid circulation and deformation.
ISSN: 0024-4937

Droits : http://creativecommons.org/licenses/by-nc-nd/
insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268/document
https://hal-insu.archives-ouvertes.fr/insu-01424268/file/Valentin-Lithos-Accepted-2016.pdf
DOI : 10.1016/j.lithos.2016.12.013

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The Ronda peridotite supplies one of the best objects to document subcontinental mantle deformation, but its internal deformation and exhumation mechanisms remain controversial. Here we provide new structural data and numerical results that constrain the Oligocene-Miocene deformation history of the Ronda massif. We first describe a mantle shear zone in the northern massif that developed subcrustal strain localization during decompression and related partial melting. The deformation regime of this mantle shear zone evolved from penetrative NE-SW stretching to sinistral shear highlighted by discrete shear bands. We then show structural observations that document a viscous deformation in the southern massif occurring prior to the thrust-assisted emplacement of the peridotite during large decompression. Finally, we performed numerical investigations that quantify a high temperature of 980°C for the basal peridotite lens at the time of its crustal emplacement. Our numerical results constrain the timing of ductile deformation of the peridotite just before 22 Ma, probably between 30 and 22 Ma. Altogether, these features led us to conclude that the deformation and exhumation of the Ronda peridotite results from lithosphere thinning subsequently inverted in the course of the Oligocene-Miocene. Among available models, our findings support the hypothesis of peridotite exhumation by the inversion of a thinned back-arc continental lithosphere during westward slab rollback through the Alboran region.
ISSN: 0278-7407

insu-00924180
https://hal-insu.archives-ouvertes.fr/insu-00924180
https://hal-insu.archives-ouvertes.fr/insu-00924180/document
https://hal-insu.archives-ouvertes.fr/insu-00924180/file/tect20062.pdf
DOI : 10.1002/tect.20062

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
We analyze the kinematics of fault tip folding at the front of a fold-and-thrust wedge using a sandbox experiment. The analog model consists of sand layers intercalated with low-friction glass bead layers, deposited in a glass-sided experimental device and with a total thickness h = 4.8 cm. A computerized mobile backstop induces progressive horizontal shortening of the sand layers and therefore thrust fault propagation. Active deformation at the tip of the forward propagating basal décollement is monitored along the cross section with a high-resolution CCD camera, and the displacement field between pairs of images is measured from the optical flow technique. In the early stage, when cumulative shortening is less than about h/10, slip along the décollement tapers gradually to zero and the displacement gradient is absorbed by distributed deformation of the overlying medium. In this stage of detachment tip folding, horizontal displacements decrease linearly with distance toward the foreland. Vertical displacements reflect a nearly symmetrical mode of folding, with displacements varying linearly between relatively well defined axial surfaces. When the cumulative slip on the décollement exceeds about h/10, deformation tends to localize on a few discrete shear bands at the front of the system, until shortening exceeds h/8 and deformation gets fully localized on a single emergent frontal ramp. The fault geometry subsequently evolves to a sigmoid shape and the hanging wall deforms by simple shear as it overthrusts the flat ramp system. As long as strain localization is not fully established, the sand layers experience a combination of thickening and horizontal shortening, which induces gradual limb rotation. The observed kinematics can be reduced to simple analytical expressions that can be used to restore fault tip folds, relate finite deformation to incremental folding, and derive shortening rates from deformed geomorphic markers or growth strata.
ISSN: 2169-9313

hal-00138061
https://hal.archives-ouvertes.fr/hal-00138061
https://hal.archives-ouvertes.fr/hal-00138061/document
https://hal.archives-ouvertes.fr/hal-00138061/file/Bernard_et_al-2007-Journalsur Geophysical_Research__Solid_Earth_%281978-2012%29.pdf
DOI : 10.1029/2005JB004149

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We report microstructural evidence for fluid-assisted ductile strain localization in a ≤ 50 m-wide mylonitic–ultramylonitic shear zone in the Ronda Peridotite massif, Southern Spain. Strain localization occurred at relatively low pressure (< 0.8 GPa) and moderate temperature (750–1000 °C). Initial deformation by dislocation creep resulted in formation of mylonites. Focusing of aqueous fluids in the shear zone favored the activation of dissolution–precipitation creep, resulting in further strain localization. This process is recorded by two generations of ultramylonitic bands composed of fine-grained, well-mixed olivine–orthopyroxene aggregates. Microstructural observations in the ultramylonites suggest alternating dissolution and precipitation of olivine and orthopyroxene, which may be explained by local changes in silica molality of the percolating fluid (disequilibrium and mass transfer at scales > mm). In the mylonites, olivine shows a crystal preferred orientation (CPO) coherent with dominant (001)[100] glide, probably due to the presence of interstitial fluids during deformation. In the ultramylonites, olivine CPO is weak to very weak, consistently with a decreasing contribution of dislocation creep to deformation. In contrast, fine-grained orthopyroxene in both mylonites and ultramylonites displays a clear CPO characterized by a [001] maximum normal to the foliation, which is not consistent with dislocation glide in any known slip system for orthopyroxene. We interpret this CPO as formed by oriented crystallization during dissolution–precipitation. In the present study, dissolution–precipitation creep predominates only in small-scale ultramylonite bands due to limited fluid availability and localized dynamic permeability. However, this process may be important in intermediate temperature domains of subduction zones, where it may lead to a feedback between strain localization and fluid transport.
ISSN: 0024-4937

hal-01395122
https://hal.archives-ouvertes.fr/hal-01395122
DOI : 10.1016/j.lithos.2016.07.038

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We conducted triaxial compression experiments to investigate the effects of pressure, temperature and strain rate on the rheology of talc rocks. The tests were carried out at T from 25 to 860 degrees C, P from 0.1 to 300 MPa, and <(epsilon) over dot> from 0.3 to 30 x 10-5 s(-1). In addition to being very weak, there are other important differences between the mechanical behavior of talc and that of most other silicates. Deformation at all temperatures up to dehydration was accommodated by a combination of crystal plasticity, frictional sliding, and cataclasis. A transition from localized to distributed deformation occurred at P = 300 MPa and T = 400 degrees C, but this transition is ill-defined as both distributed and localized deformation were observed at P = 300 MPa and T = 600 degrees C. Unlike most silicates, both the coefficient of internal friction and the coefficient of (sliding) friction are very low and nearly equal to each other. Temperature enhances plastic deformation (kinking), and inter- and intra-granular microcracks are observed parallel to the (001) planes at all conditions. Voids are created by delamination along (001) planes at kink-band boundaries. Full crystal plasticity was not achieved under any of the conditions tested, i.e., the von Mises criterion was never satisfied. However, the strength of the aggregates remained much less than the confining pressure. These unusual properties are likely a manifestation of the pronounced mechanical anisotropy of talc at the grain scale. At T >= 750 degrees C dehydration is observed, but only along shear zones. These results suggest that feedbacks between deformation and reaction kinetics could control fluid flow in fault zones. The presence of talc can promote significant weakening and strain localization in the oceanic lithosphere, the subducting plate and the overlying mantle wedge. (c) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00492706
https://hal.archives-ouvertes.fr/hal-00492706
DOI : 10.1016/j.epsl.2008.02.004

Éditeur(s) : HAL CCSD The Geochemical Society of Japan
Résumé : International audience
The Western Cordillera of Ecuador consists of Cretaceous crustal fragments of oceanic plateaux and superimposed insular arcs, which were accreted to the northwestern South American margin during the Late Cretaceous and Paleocene. Slices of high-grade metabasites, ultramafic rocks, gabbros and basalts, unmetamorphosed radiolarian cherts and scarce garnet-bearing metasediments were randomly exhumed along Miocene to Recent transcurrent faults crosscutting the Western Cordillera. The basalts show geochemical characteristics of oceanic plateau basalts (flat REE patterns, La/Nb = 0.85). The gabbros differ from the basalts in having lower REE levels, positive Eu anomalies, and negative Nb and Ta anomalies; they are interpreted as resulting from arc magmatism. The amphibolites and banded amphibolites have major and trace element chemistry similar to that of oceanic plateau basalts (flat REE patterns, La/Nb = 0.86) or to cumulate gabbros. The granulite shares with oceanic plateaus similar trace element chemistry (flat REE patterns, La/Nb < 1) and εNdi values (+7.6). Continent-derived metasediments are depleted in heavy REE (La/Y = 4.8) and have a negative Eu anomaly. Foliated lherzolites, melagabbronorites and pyroxenites consist of serpentinized olivine + cpx + opx ± Ca-plagioclase. Lherzolites, melagabbronorites and pyroxenites are LREE depleted with positive Eu anomalies, while the harzburgite displays a U-shaped REE pattern. The trace element abundances of the ultramafic rocks are very low (0.1 to 1 times the chondritic and primitive mantle values). The ultramafic rocks represent fragments of depleted mantle, deformed cpx-rich cumulate, and continental lithospheric mantle or mantle contaminated by subduction-fluid. Except the scarce quartz-rich metasediments, all these rocks likely represent remnants of accreted oceanic crustal fragments and associated depleted mantle. Since these samples were randomly sampled at depth by the fault, we propose that the Western Cordillera and its crustal root are mainly of oceanic nature.
ISSN: 0016-7002

insu-00679228
https://hal-insu.archives-ouvertes.fr/insu-00679228

Éditeur(s) : HAL CCSD
Résumé : We present an experimental study of relations between hydraulic properties of clayey rocks and their deformation at bulk and micro scale. The experimentation is based on triaxial deformation of kaolinitic core samples, on permeability measurements, and on several methods of analysis of the microstructure. To produce the samples, remoulded kaolinite material is consolidated by axial loading up to 20 MPa in an oedometric cell. Then, in a triaxial cell, an undrained stress path is applied in order to induce shearing damage in the sample. The permeability of the sample is measured by fluid flow across the sample. Before and after these hydro-mechanical tests, the evolution and the homogeneity of the pore space and moreover the texture of the material are analysed by X-ray tomography, environmental scanning electron microscopy and thermic neutron diffraction. Contrary to expectations, the permeability at the sample scale does not vary significantly, although quite large deformation is reached. The final deformation is heterogeneous, with well-developed shear bands. It appears that the development of compacting and dilating zones generates a heterogeneous permeability field, which results in a negligible variation of the bulk permeability at the sample scale.
International Journal of Rock Mechanics and Mining Science

hal-00496407
https://hal.archives-ouvertes.fr/hal-00496407
DOI : 10.1016/j.ijrmms.2010.04.007

Éditeur(s) : HAL CCSD
Résumé : International audience
Metamorphic soles correspond to m to 500 m thick highly strained metamorphic rock units found beneath myloniticbanded peridotites at the base of large-scale ophiolites, as exemplified in Oman. Metamorphic soles aremainly composed of metabasalts deriving from the downgoing oceanic lithosphere and metamorphosed up togranulite-facies conditions by heat transfer from the mantle wedge. Pressure–temperature peak conditions areusually estimated at 1.00.2 GPa and 800100ºC. The absence of HP–LT metamorphism overprint implies thatmetamorphic soles have been formed and exhumed during subduction infancy. In this view, metamorphic soleswere strongly deformed during their accretion to the mantle wedge (corresponding, now, to the base of the ophiolite).Therefore, metamorphic soles and banded peridotites are direct witnesses of the dynamics of early subductionzones, in terms of thermal structure, fluid migration and rheology evolution across the nascent slab interface.Based on fieldwork and EBSD analyses, we present a detailed (micro–) structural study performed on samplescoming from the Sumeini window, the better-preserved cross-section of the metamorphic sole of Oman. Largedifferences are found in the deformation (CPO, grain size, aspect ratio) of clinopyroxene, amphibole and plagioclase,related to mineralogical changes linked with the distance to the peridotite contact (e.g., hardening due to theappearance of garnet and clinopyroxene).To model the incipient slab interface in laboratory, we carried out 5 hydrostatic annealing and simple-shear experimentson Griggs solid-medium apparatus. Deformation experiments were conducted at axial strain rates of 10-6s-1. Fine-grained amphibolite was synthetized by adding 1 wt.% water to a (Mid-Ocean Ridge) basalt powder asa proxy for the metamorphic sole (amphibole + plagioclase + clinopyroxene garnet assemblage). To synthetizegarnet, 2 experiments were carried out in hydrostatic conditions and with deformation at 800C with confiningpressure of 2 GPa. Another simple-shear experiment has been carried out at 800C and 1 GPa with fined-grainednatural garnet. With the aim of mimicking the early slab interface (between the metamorphic sole and bandedperidotites at the base of the ophiolite), 2 simple-shear deformation experiments with 2 layers have been carriedout at 800C and confining pressure of 1 GPa. The bottom layer was made of hydrated basalt powder and the toplayer was made of olivine.Fined-grained garnet-free amphibolite is significantly weaker than dunite but the appearance of harder mineralsin the amphibolite (garnet and clinopyroxene) has major implications on its rheological evolution. These resultsallow liking field observations of strain localization at the interface to the metamorphic sole formation
European Geosciences Union General Assembly 2016
Vienne, Austria

insu-01309394
https://hal-insu.archives-ouvertes.fr/insu-01309394

Éditeur(s) : HAL CCSD
Résumé : International audience
Experimental, and Numerical Studies of Deformation Localization Bands
EOS

hal-00667412
https://hal.archives-ouvertes.fr/hal-00667412

Éditeur(s) : HAL CCSD Royal Society, The
Résumé : International audience
Nucleation mechanisms occurring during dynamic recrystallization play a crucial role in the evolution of microstructures and textures during high temperature deformation. In polycrystalline ice, the strong viscoplastic anisotropy induces high strain heterogeneities between grains which control the recrystallization mechanisms. Here, we study the nucleation mechanisms occurring during creep tests performed on polycrystalline columnar ice at high temperature and stress (T=−5°C;σ=0.5 MPa) by post-mortem analyses of deformation microstructures using cryogenic electron backscatter diffraction. The columnar geometry of the samples enables discrimination of the nuclei from the initial grains. Various nucleation mechanisms are deduced from the analysis of the nuclei relations with the dislocation sub-structures within grains and at grain boundaries. Tilt sub-grain boundaries and kink bands are the main structures responsible for development of polygonization and mosaic sub-structures. Nucleation by bulging at serrated grain boundaries is also an efficient nucleation mechanism near the grain boundaries where strain incompatibilities are high. Observation of nuclei with orientations not related to the ‘parent’ ones suggests the possibility of ‘spontaneous’ nucleation driven by the relaxation of the dislocation-related internal stress field. The complexity of the nucleation mechanisms observed here emphasizes the impact of stress and strain heterogeneities on dynamic recrystallization mechanisms.This article is part of the themed issue ‘Microdynamics of ice’.
ISSN: 1364-503X

hal-01467152
https://hal.archives-ouvertes.fr/hal-01467152
DOI : 10.1098/rsta.2015.0345

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Interactions between deformation and melt percolation yield important consequences for the evolution of the mantle lithosphere, controlling its composition and mechanical behavior. In the Lherz massif (Pyrenees, France), the analysis of structural relationships between harzburgites, lherzolites and pyroxenites and of the crystal-preferred orientations (CPO) of olivine and pyroxenes highlights a strong feedback between percolation of basaltic melts and deformation under near-solidus conditions at the lithosphere–asthenosphere boundary. Elongated harzburgite bodies up to tens of meters wide, which are the remnants of an old lithospheric mantle, preserve a constant foliation. This foliation is locally outlined by cm-scale flattened websteritic lenses. At the contact with the enclosing lherzolites, the harzburgite foliation is crosscut by the lherzolites foliation and by cm-wide websterite bands parallel to the contact. Strain intensity in the lherzolites increases with distance to the harzburgites. Based on these observations, we propose that reactive percolation was synchronous to the deformation and propose that variations in instantaneous melt fraction, due to pyroxenes and spinel crystallization during reactive melt transport, guided strain localization. Accordingly, the observed decrease in olivine CPO intensity and change in CPO patterns from harzburgites to distal lherzolites are interpreted as recording changes in the relative contribution of dislocation glide and diffusion processes, which is ruled by a balance between the instantaneous melt fraction and the local strain rate. We also propose that the pervasive websteritic layering in the refertilized lherzolites may result from deformation-assisted melt segregation in a system with decreasing permeability due to refertilization reactions. Finally, we discuss the possible timing and geodynamical context of the refertilization episode.
ISSN: 0012-821X

hal-00411724
https://hal.archives-ouvertes.fr/hal-00411724
DOI : 10.1016/j.epsl.2008.07.053

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Crystal growth driven by a flowing solution is modeled for a flow with low Reynolds number using a computational dynamic software. Considering equivalent crystallographic faces, the chemical flux is calculated along upstream and downstream faces. Upstream flux is higher compared to downstream and leads to a symmetry breakdown of the crystal shape and develops mirror symmetry parallel to the flow velocity. Moreover the ratio of these two fluxes (upstream / downstream) gives a quantitative relation between the relative crystal growth rate and the flow velocity. Thus, using an inverse method, the flow direction and velocity can be deduced by the study of the variation of the growth band thicknesses of equivalent crystallographic faces. This new method was applied to the formation of metasomatic tourmalinite associated with a leucogranite sill. The approach is complemented by a study of the chemistry of the tourmaline. In the studied case, the application of the new method gives the high fluid velocities in pores (10-3 - 10-4 m/s) during metasomatism. Equivalent Darcy velocities are estimated and discussed accounting for the major role played by the regional deformation. Finally, a two-stage tectono-hydrodynamic model is proposed for the metsomatism. The first stage is genetically linked to the sill injection, and the second is characterized by a wider event with hydrothermal flow passing along the leucogranite sills.
ISSN: 0012-821X

Droits : info:eu-repo/semantics/OpenAccess
insu-00352307
https://hal-insu.archives-ouvertes.fr/insu-00352307
https://hal-insu.archives-ouvertes.fr/insu-00352307/document
https://hal-insu.archives-ouvertes.fr/insu-00352307/file/Sizaret_et_al_final.pdf
DOI : 10.1016/j.epsl.2009.01.013