Éditeur(s) : HAL CCSD Elsevier
Résumé : Spinel peridotite xenoliths from Persani Mountains, Southeastern Carpathians, Romania, were submitted to deformation by dislocation creep accompanied by dynamic recrystallization under variable stress and temperature conditions. Predominance of low-angle boundaries parallel to (100) with well-defined [Ovw] rotation axes in olivine indicates that subgrain rotation is the main recrystallization mechanism and that dislocation glide occurs mainly in [100]{0k1} systems. Analysis of olivine crystal preferred orientations highlights that recrystallization results in dispersion of the orientations of recrystallized grains relatively to the parent grains. This dispersion may be quantified by a dimension-less dispersion factor defined as the ratio of the random component of the [100] axis distributions between the recrystallized grains and porphyroclasts. This factor is largely independent from the overall fabric strength, the number of grains analyzed, and the recrystallized grain size. The olivine CPO strength and anisotropy at the rock scale, quantified by J-index, are largely controlled by the volume of recrystallized grains, which depends on finite strain. Comparison of olivine CPO in coarse- and fine-grained porphyroclastic peridotites shows that deviatoric stress and temperature conditions play nevertheless a role on the CPO evolution during recrystallization; selective grain growth, which is favored at high temperature and low stresses, does counteract the dispersion produced by the nucleation processes.
ISSN: 0191-8141

hal-00669963
https://hal.archives-ouvertes.fr/hal-00669963
DOI : 10.1016/j.jsg.2011.09.010

Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers (IEEE)/Optical Society of America(OSA)
Résumé : International audience
Nanometric displacement measurements by Extrinsic Fiber Fabry-Perot interferometers (EFPI) is extremely susceptible to external environmental changes. Temperature, in particular, has a remarkable influence on the optical power and wavelength of the laser diode in use, in addition to the thermal expansion of the mechanical structure. In this paper we propose an optimization of the EFPI sensor in order to use it for very long-term (more than one year) and for high-precision displacement measurements. For this purpose, a real time and adaptive estimation procedure based on a homodyne technique and a Kalman filter is established. During a sinusoidal laser diode current modulation, the Kalman filter provides a correction of the amplitude drift caused by the resultant optical power modulation and external perturbations. Besides, stationary temperature transfer operators are estimated via experimental measurements to reduce the additive thermal noise induced in the optical phase and mechanical components.
ISSN: 0733-8724

hal-00876339
https://hal.archives-ouvertes.fr/hal-00876339
DOI : 10.1109/JLT.2012.2194476

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : Mantle xenoliths in Pliocene alkali basalts of the eastern Betics (SE Iberia, Spain) are spinel ± plagioclase lherzolite, with minor harzburgite and wehrlite, displaying porphyroclastic or equigranular textures. Equigranular peridotites have olivine crystal preferred orientation (CPO) patterns similar to those of porphyroclastic xenoliths but slightly more dispersed. Olivine CPO shows [100]-fiber patterns characterized by strong alignment of [100]-axes subparallel to the stretching lineation and a girdle distribution of [010]-axes normal to it. This pattern is consistent with simple shear or transtensional deformation accommodated by dislocation creep. One xenolith provides evidence for synkinematic reactive percolation of subduction-related Si-rich melts/fluids that resulted in oriented crystallization of orthopyroxene. Despite a seemingly undeformed microstructure, the CPO in orthopyroxenite veins in composite xenoliths is identical to those of pyroxenes in the host peridotite, suggesting late-kinematic crystallization. Based on these observations, we propose that the annealing producing the equigranular microstructures was triggered by melt percolation in the shallow subcontinental lithospheric mantle coeval to the late Neogene formation of veins in composite xenoliths. Calculated seismic properties are characterized by fast propagation of P waves and polarization of fast S waves parallel to olivine [100]-axis (stretching lineation). These data are compatible with present-day seismic anisotropy observations in SE Iberia if the foliations in the lithospheric mantle are steeply dipping and lineations are subhorizontal with ENE strike, implying dominantly horizontal mantle flow in the ENE-WSW direction within vertical planes, that is, subparallel to the paleo-Iberian margin. The measured anisotropy could thus reflect a lithospheric fabric due to strike-slip deformation in the late Miocene in the context of WSW tearing of the subducted south Iberian margin lithosphere.
ISSN: 0278-7407

Droits : info:eu-repo/semantics/OpenAccess
hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809/document
https://hal.archives-ouvertes.fr/hal-01685809/file/Hidas_et_al-2016-Tectonics.pdf
DOI : 10.1002/2016TC004165

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Splitting of teleseismic shear waves has been measured in the Appalachians (eastern USA) and the Pyrenees (western Europe) using data recorded by permanent and portable stations. From a comparison of the results, it appears that an interpretation of the recorded seismic anisotropy in terms of geodynamics is not straightforward. Successive geodynamic events have generated structures that may have resulted in a similar pattern of mantle flow and that therefore may have contributed in the development of the recorded anisotropy. Combining geological and geophysical arguments, it appears that the mantle anisotropy measured across the Appalachians and the Pyrenees may not be systematically Appalachian or Pyrenean in age but may be mainly due to a lithospheric structure formed during earlier major tectonic events, i.e. the Grenvillian and the Hercynian orogenies, respectively. We suggest that during major episodes of continent assembly, a pervasive tectonic fabric is developed in the lithospheric mantle. In the subsequent evolution of the continent, this fabric may induce a significant mechanical anisotropy that will drastically influence the mechanical behaviour of the Iithosphere when submitted to new tectonic events.
ISSN: 0031-9201

hal-01389717
http://hal.univ-reunion.fr/hal-01389717
http://hal.univ-reunion.fr/hal-01389717/document
http://hal.univ-reunion.fr/hal-01389717/file/Vauchez_Barruol-PEPI96_hal.pdf
DOI : 10.1016/0031-9201(95)03125-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In the Tahalgha district (southwestern Hoggar, Algeria), the Cenozoic volcanism has sampled subcontinental mantle beneath two crustal terranes that collided during the Pan-African orogeny: the “Polycyclic Central Hoggar” to the east and the “Western Hoggar” to the west. Two major lithospheric shear zones separate these terranes: the “4°35” and the “4°50” faults. Mantle xenoliths were collected between the two faults and across the 4°35 fault. In addition to a range in equilibrium temperatures and chemical compositions reported elsewhere, the samples show variations in their microstructures and crystallographic preferred orientations. Equilibrium temperatures and geochemical characteristics allow dividing them into low — (LT; 700–900 °C), intermediate — (IT; 900–1000 °C), and high-temperature (HT; 1000–1100 °C) xenoliths. The LT and IT peridotites occur on both sides of the 4°35 fault; they are usually coarse-grained. HT xenoliths are present only east of the 4°35 fault, in the narrow domain stuck between the two faults; they are fine-grained and extensively affected by annealing and melt–rock reactions. Microstructures and crystallographic textures indicate that deformation in the LT- and IT-xenoliths occurred through dislocation creep under relatively high-temperature, low-pressure conditions, followed by post-kinematic cooling. The fine-grained HT-xenoliths were deformed under relatively high-stress conditions before being annealed.Combining microstructural and CPO data with petrological and geochemical informations suggests that: (1) the LT xenoliths are remnants of the Neoproterozoic lithospheric mantle that preserved microstructural and chemical characteristics inherited from the Pan-African orogeny, and (2) the HT xenoliths record localized Cenozoic deformation associated with melt channeling through feed-back processes that culminated in the formation of high-permeability porous-flow conduits. Limited grain-growth in HT xenoliths suggests that advective heating of melt conduits was transient and rapidly followed by thermal relaxation due to conductive heat loss into wall-rock peridotites represented by the IT xenoliths, then by exhumation due to volcanic activity.
ISSN: 0040-1951

hal-01171761
https://hal.archives-ouvertes.fr/hal-01171761
DOI : 10.1016/j.tecto.2014.11.012

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Large earthquakes nucleate at tectonic plate boundaries, and their occurrence within a plate's interior remains rare and poorly documented, especially offshore. The two large earthquakes that struck the northeastern Indian Ocean on 11 April 2012 are an exception: they are the largest strike-slip events reported in historical times1, 2 and triggered large aftershocks worldwide3. Yet they occurred within an intra-oceanic setting along the fossil fabric of the extinct Wharton basin, rather than on a discrete plate boundary4, 5, 6, 7, 8. Here we show that the 11 April 2012 twin earthquakes are part of a continuing boost of the intraplate deformation between India and Australia that followed the Aceh 2004 and Nias 2005 megathrust earthquakes, subsequent to a stress transfer process recognized at other subduction zones9, 10. Using Coulomb stress change calculations, we show that the coseismic slips of the Aceh and Nias earthquakes can promote oceanic left-lateral strike-slip earthquakes on pre-existing meridian-aligned fault planes. We further show that persistent viscous relaxation in the asthenospheric mantle several years after the Aceh megathrust explains the time lag between the 2004 megathrust and the 2012 intraplate events. On a short timescale, the 2012 events provide new evidence for the interplay between megathrusts at the subduction interface and intraplate deformation offshore. On a longer geological timescale, the Australian plate, driven by slab-pull forces at the Sunda trench, is detaching from the Indian plate, which is subjected to resisting forces at the Himalayan front6, 8, 11.
ISSN: 0028-0836

hal-00767569
https://hal.archives-ouvertes.fr/hal-00767569
DOI : 10.1038/nature11520

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
New petrographic and microstructural observations, mineral equilibria modelling and U/Pb (monazite) geochronological studies were carried out to investigate the relationships between deformation and metamorphism across the Rehamna massif (Moroccan Variscan belt). In this area, typical Barrovian (muscovite to staurolite) zones developed in Cambrian to Carboniferous metasedimentary rocks that are distributed around a dome-like structure. First assemblages are characterized by the presence of locally preserved andalusite, followed by prograde evolution culminating at 6 kbar and 620 °C in the structurally deepest staurolite zone rocks. This Barrovian sequence was subsequently uplifted to supracrustal levels, heterogeneously reworked at greenschist facies conditions, which was followed locally by static growth of andalusite, indicating heating to 2.5–4 kbar and 530–570 °C. The 206Pb/238U monazite age of 298.3 ± 4.1 Ma is interpreted as minimum age of peak metamorphic conditions, whereas the ages of 275.8 ± 1.7 Ma and 277.0 ± 1.1 Ma date decompression and heating at low pressure, in agreement with previous dating of Permian granitoids intruding the Rehamna massif. The prograde metamorphism occurred during thickening and associated horizontal flow in the deeper crust (S1 horizontal schistosity). The horizontally disposed metamorphic zones were subsequently uplifted by a regional scale antiform during ongoing N–S compression. The re-heating of the massif follows late massive E–W shortening, refolding and retrograde shearing of all previous fabrics coevally with regionally important intrusions of Permian granitoids. We argue that metamorphic evolution of the Rehamna massif occurred several hundred kilometres from the convergent plate boundaries in the interior of continental Gondwanan plate. The tectonometamorphic history of the Rehamna massif is put into Palaeozoic plate tectonic perspective and Late Carboniferous reactivation of (Devonian)–Early Carboniferous basins formed during stretching of the north Gondwana margin and formation of the Palaeotethys Ocean. The inherited heat budget of these magma-rich basins plays a role in the preferential location of this intracontinental orogen. It is shown that rapid transition from lithospheric stretching to compression is characterized by specific HT type of Barrovian metamorphism, which markedly differs from similar Barrovian sequences along Palaeozoic plate boundaries reported from Variscan Europe.
ISSN: 0263-4929

hal-01468009
https://hal.archives-ouvertes.fr/hal-01468009
DOI : 10.1111/jmg.12214

Éditeur(s) : HAL CCSD
Résumé : International audience
The Kazdağ Massif exposes a metamorphic dome in the Biga Peninsula of northwest Turkey. An extensional origin has been proposed for the dome, limited on both flanks by detachments and/or shear zones. The northern flank is bounded by the extensional Alakeçi Shear Zone (ASZ), whose P-T-t path is still poorly known. We therefore focus on its metamorphic conditions and related temporal history to precise its tectono-metamorphic evolution. The local tectonostratigraphy in structurally ascending order comprises: (i) the high-grade metamorphic core rocks of the Kazdaǧ Massif (gneisses and micaschists intercalated with amphibolites and marbles); (ii) the two kilometer-thick ASZ; (iii) the overlaying unmetamorphosed pre-Cenomanian accretionary Çetmi mélange; and (iv) Neogene sedimentary and volcanic cover rocks. ASZ mylonites were derived from both the core rocks and the mélange lithologies. From the north to the south the mylonitic fabrics in the ASZ depict a top-to-the N-NNE shearing, parallel to the NNE-plunging stretching lineation and NNW-dipping mylonitic foliation. This geometry implies normal sense movement i.e. north-side down-dip extensional displacement along this flank of the Kazdaǧ Massif. The northward transition from ductile to brittle-ductile regime through the ASZ shows that the deformation occurred at decreasing temperatures and degree of metamorphism. The paragenesis in equilibrium within the mylonitic gneisses and schists contains Qtz + Fs + Ms + Bt + Grt ± St ± Sill, with late retrogressive chlorite after biotite and garnet. Four samples of ASZ rocks yielded pressures between 6.9-5.7 kbar and temperatures between 706-587°C. Three samples from the mylonitic rocks supplied in situ isochron 36Ar/40Ar mica ages between 31.2-24.2 Ma, which we interpret to date the cooling of the mylonites following the P-T decrease across the ASZ. The metamorphic and structural results support the extensional character of the ASZ, and sketch transition from sillimanite core gneisses in the deeper structural levels to chlorite schists towards the top of the shear zone. These new data allow to precise the peak P-T conditions and the temporal evolution in the northern flank of the Kazdaǧ Massif, where Late Oligocene extensional exhumation was assisted by NNE-directed ductile-brittle ASZ, which had operated from amphibolite to greenschist facies. At the regional scale, this tectono-metamorphic pattern is similar to those observed on other places of the north Aegean domain.
IOP Conference Series
Austin, TE, United States

hal-00642725
https://hal-brgm.archives-ouvertes.fr/hal-00642725
DOI : 10.1088/1755-1307/2/1/012012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The N-S oriented Raghane shear zone (8 degrees 30') delineates the western boundary of the Saharan metacraton and is, with the 4 degrees 50' shear zone, the most important shear zone in the Tuareg shield. It can be followed on 1000 km in the basement from southern Air, Niger to NE Hoggar, Algeria. Large subhorizontal movements have occurred during the Pan-African orogeny and several groups of granitoids intruded during the Neoproterozoic. We report U-Pb zircon datings (laser ICP-MS) showing that three magmatic suites of granitoids emplaced close to the Raghane shear zone at c. 790 Ma, c. 590 and c. 550 Ma. A comprehensive and detailed (158 sites, more than 1000 cores) magnetic fabric study was performed on 8 plutons belonging to the three magmatic suites and distributed on 200 km along the Raghane shear zone. The main minerals in all the target plutons do not show visible preferential magmatic orientation except in narrow shear zones. The AMS study shows that all plutons have a magnetic lineation and foliation compatible with the deformed zones that are zones deformed lately in post-solidus conditions. These structures are related to the nearby mega-shear zones, the Raghane shear zone for most of them. The old c. 793 Ma Touffok granite preserved locally its original structures. The magnetic structures of the c. 593 Ma Ohergehem pluton, intruded in the Aouzegueur terrane, are related to thrust structures generated by the Raghane shear zone while it is not the case of the contemporaneous plutons in the Assode-Issalane terrane whose structures are only related to the subvertical shear zones. Finally, the c. 550 Ma granite group has magnetic structure related to the N-S oriented Raghane shear zone and its associated NNE-SSW structures when close to them, but NW-SE oriented when further. These NW-SE oriented structures appear to be characteristic of the late Neoproterozoic evolution of the Saharan metacraton and are in relation to the convergence with the Murzuq craton. This evolution reflects the rheological contrast existing along the Raghane shear zone marking the western boundary of the Saharan metacraton.
ISSN: 0040-1951

hal-00429354
https://hal.archives-ouvertes.fr/hal-00429354
DOI : 10.1016/j.tecto.2009.04.022

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
We have investigated the seismic anisotropy from SKS and SKKS wave splitting along a N-S profile perpendicular to the Pyrenean mountain belt. The line crossed the North Pyrenean Fault (NPF), which probably represents the plate boundary between the European and the Iberian plates. We observed large delay times δt (1.3 to 1.5 s) and uniform fast polarization directions ϕ (N100E) at three stations located on the Iberian plate. On the other hand, δt are smaller (0.5–1.0 s) and the ϕ scattered at stations located north of the NPF. The small scale variability, the relation with surface geology and the correlation of the δt with lithospheric thickness suggest that the anisotropy could be predominantly of lithospheric origin. However, an asthenospheric contribution cannot be ruled out. In the North Pyrenean Zone, an important thermal event before the Pyrenean compression has likely erased the former mantle fabric. The observed anisotropy is then likely related to the Pyrenean orogeny. On the Iberian plate, our splitting parameters are similar to those obtained at two stations located on Hercynian structures in Central Spain. This suggests that two contributions are likely superposed to that of the Pyrenean built up: one related to the Hercynian orogeny and the other one related to the rotation of the Iberian plate.
ISSN: 0094-8276

hal-01389118
http://hal.univ-reunion.fr/hal-01389118
http://hal.univ-reunion.fr/hal-01389118/document
http://hal.univ-reunion.fr/hal-01389118/file/barruol_pyr_GRL1995.pdf
DOI : 10.1029/94GL03225

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Sensitive instruments like strainmeters and tiltmeters are necessary for measuring slowly varying low amplitude Earth deformations. Nonetheless, laser and fibre interferometers are particularly suitable for interrogating such instruments due to their extreme precision and accuracy. In this paper, a practical design of a simple pendulum borehole tiltmeter based on laser fibre interferometric displacement sensors is presented. A prototype instrument has been constructed using welded borosilicate with a pendulum length of 0.85 m resulting in a main resonance frequency of 0.6 Hz. By implementing three coplanar extrinsic fibre Fabry-Perot in-terferometric probes and appropriate signal filtering, our instrument provides tilt measurements that are insensitive to parasitic deformations caused by temperature and pressure variations. This prototype has been installed in an underground facility (Rustrel, France) where results show accurate measurements of Earth strains derived from Earth and ocean tides, local hydro-logic effects, as well as local and remote earthquakes. The large dynamic range and the high sensitivity of this tiltmeter render it an invaluable tool for numerous geophysical applications such as transient fault motion, volcanic strain and reservoir monitoring.
ISSN: 0956-540X

hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967/document
https://hal.archives-ouvertes.fr/hal-01265967/file/HCS1.pdf
DOI : 10.1093/gji/ggv358

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The strike-slip faults of north Tibet accommodate part of the Cenozoic convergence between India and Asia. Along the Karakax valley south of Yecheng and near the Xidatan trough south of Golmud, the active traces of the Altyn-Tagh and Kunlun faults follow narrow belts of metamorphic rocks. The deformation recorded in those mylonites is sinistral strike-slip. Rb/Sr and 40Ar/39Ar ages of deformation from syntectonic fabrics formed at 350–400°C 120 Ma. Argon loss suggests that deformation was associated to a 250–300°C thermal pulse that lasted 5–20 Ma after the onset of movement. Unroofing occurred much later, around 25 Ma when sudden cooling suggests a component of thrusting or more likely normal faulting. The Cretaceous shear may be related to collision between the Qiantang and the Lhasa blocks. The Karakax and Xidatan shear zones may have formed a unique, continuous boundary in the Cretaceous, which was later reused by the Tertiary strike-slip faults, leading to potentially calculable offsets along the Altyn-Tagh fault.
ISSN: 2169-9313

hal-00197562
https://hal.archives-ouvertes.fr/hal-00197562
https://hal.archives-ouvertes.fr/hal-00197562/document
https://hal.archives-ouvertes.fr/hal-00197562/file/Arnaud_JGR000904_def.pdf
DOI : 10.1029/2001JB000904

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
New U–Pb monazite, zircon, and xenotime ages date the Late Carboniferous crystallization of the anatectic Vialais granite in the Montagne Noire Axial Zone and the high-temperature deformation and metamorphism of the augen gneiss (Ordovician granite protolith) from which the granite was likely derived. The U–Pb monazite ages obtained from the augen gneiss (308 ± 3 Ma), late kinematic Vialais granite (303 ± 4 Ma), and post-kinematic leucogranite (298 ± 2 Ma), bracket the high-temperature deformation and metamorphism at ~ 310–300 Ma, clearly postdating regional contraction and nappe emplacement (> 320 Ma). The planar–linear and locally linear fabrics in the augen gneiss outline a regional-scale double dome structure (Caroux and Espinouse sub-domes) containing smaller (km-scale) upright folds. Compared to the Caroux sub-dome, the larger, migmatitic Espinouse sub-dome contains abundant leucosome, leucogranite bodies and late-kinematic intrusions (Vialais granite). The Vialais granite displays a weak magmatic foliation that defines the main layering of the Espinouse migmatite. Ellipsoidal quartz–sillimanite nodules concentrated above the roof of the granite recorded an increment of strain (vertical shortening, E–NE elongation) during granite emplacement and crystallization, consistent with the extension event that exhumed the domes. These new geochronological and structural data suggest that the Montagne Noire double dome formed in a pull-apart structure within a dextral strike–slip system. Upright folding in the sub-domes has been traditionally assigned to a regional contraction event; alternatively, we propose that local contraction is associated with the convergence of low-viscosity crust beneath the upper crust pull-apart. Dynamic models of extension of hot crust indicate that contraction at depth is generated by flow of low-viscosity orogenic crust converging and rising to fill the gap created by upper crust extension. This interpretation solves the long-standing problem of apparent coeval contraction and extension in the Montagne Noire double dome and establishes migmatite dome emplacement in strike–slip corridors as a style of late Variscan tectonics.
ISSN: 0040-1951

insu-01112009
https://hal-insu.archives-ouvertes.fr/insu-01112009
DOI : 10.1016/j.tecto.2014.12.002

Éditeur(s) : HAL CCSD American Physical Society
Résumé : International audience
This is the second of two papers investigating the mechanical response of cemented granular materials by means of contact dynamics simulations. In this paper, a two-dimensional polydisperse sample with high void ratio is sheared in a load-controlled simple shear numerical device until the stress state of the sample reaches the yield stress. We first study the stress transmission properties of the granular material in terms of the fabric of different subsets of contacts characterized by the magnitude of their normal forces. This analysis highlights the existence of a peculiar force carrying structure in the cemented material, which is reminiscent of the bimodal stress transmission reported for cohesionless granular media. Then, the evolution of contact forces and torques is investigated trying to identify the micromechanical conditions that trigger macroscopic yielding. It is shown that global failure can be associated to the apparition of a group of particles whose contacts fulfill at least one of the local rupture conditions. In particular, these particles form a large region that percolates through the sample at the moment of failure, evidencing the relationship between macroscopic yielding and the emergence of large-scale correlations in the system.
ISSN: 1539-3755

hal-00523451
https://hal.archives-ouvertes.fr/hal-00523451
DOI : 10.1103/PhysRevE.82.011304

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Gibraltar arc, spans a complex portion of the Africa-Eurasia plate boundary marked by slow oblique convergence and intermediate and deep focus seismicity. The seemingly contradictory observations of a young extensional marine basin surrounded by an arcuate fold-and-thrust belt, have led to competing geodynamic models (delamination and subduction). Geophysical data acquired in the past decade provide a test for these models and support a narrow east-dipping, subduction zone. Seismic refraction studies indicate oceanic crust below the western Gulf of Cadiz. Tomography of the upper mantle reveals a steep, east-dipping high P-wave velocity body, beneath Gibraltar. The anisotropic mantle fabric from SKS splitting shows arc-parallel "fast directions", consistent with toroidal flow around a narrow, westward retreating subducting slab. The accompanying WSW advance of the Rif-Betic mountain belt has constructed a thick pile of deformed sediments, an accretionary wedge, characterized by west-vergent thrust anticlines. Bathymetric swath‐mapping images an asymmetric embayment at the deformation front where a 2 km high basement ridge has collided. Subduction has slowed significantly since 5 Ma, but deformation of recent sediments and abundant mud volcanoes suggest ongoing activity in the accretionary wedge. Three possible origins for this deformation are discussed; gravitational spreading, overall NW-SE convergence between Africa and Iberia and finally a WSW tectonic push from slow, but ongoing roll-back subduction. In the absence of arc volcanism and shallow dipping thrust type earthquakes, evidence in favor of present-day subduction can only be indirect and remains the object of debate. Continued activity of the subduction offers a possible explanation for great (M > 8.5) earthquakes known to affect the area, like the famous 1755 Great Lisbon earthquake. Recent GPS studies show SW motion of stations in N Morocco at velocities of 3-6 mm/yr indicating the presence of an independent block, a "Rif-Betic-Alboran" microplate, situated between Iberia and Africa.
ISSN: 0040-1951

insu-00769762
https://hal-insu.archives-ouvertes.fr/insu-00769762
DOI : 10.1016/j.tecto.2012.08.038

Éditeur(s) : HAL CCSD
Résumé : Geological storage of CO2 is one of diverse technologies being explored to reduce atmospheric carbon fromindustrial processes (i.e. fossil fuel combustion). One of the specific features of CO2 injection is the possibility ofgeochemical reactions (dissolution – precipitation) between mobile reactive brine (e.g. formation water enrichedin CO2) and the host rock during the spatial and temporal evolution of CO2. That leads to modifications in thepore structure, which in turn change the flow dynamics of the reservoir (e.g. the permeability k). Then, thesesstructural modifications can largely control the injectivity, so that the pressure field in the reservoir and also theCO2 propagation. Accordingly, it is crucial to explore the changes in the reservoir properties (e.g. structural andhydrodynamic) induced during a CO2 injection and specially the relationships between them (e.g. k or reactivesurface-Sr versus porosity-φ , k versus rock heterogeneity), for developing predictive modelling tools of thetransport and reaction processes occurring during a CO2 injection and reliable risk assessment. In the case ofcarbonate rocks, the application of the predictive models of transport and reaction is still challenging, because oftheir high heterogeneity so that the incertitude in the reaction kinetics of carbonate minerals.From this perspective, we realized brine-enriched in CO2 percolation experiments through carbonate rocksamples in thermodynamic conditions expected during CO2 injection in deep reservoirs (T = 100°C et P =12MPa). The permeability changes k(t) is monitored during the experiments and the porosity variationφ (t) iscalculated from chemical analyses of the sampled outlet fluids, using ICP-EAS. The pore structure modificationsare investigated from high resolution X ray micro tomography images acquired from the synchrotron ofGrenoble (ESRF). Depending to the dissolution regime, controlled by the reservoir rock fabric and the chemicalcomposition of the brine (e.g. PCO2), we observed that a modification of pore structure can either improve(atypical result in dissolution context) or impair the value of the permeability k.
Le stockage géologique du CO2 est l’une des diverses technologies étant explorées afin deréduire les émissions de carbone atmosphérique des processus industriels (i.e. combustion del’énergie fossile). L’une des spécifiques caractéristiques de l’injection du CO2 en profondeurreste la possibilité de réactions géochimiques (dissolution-précipitation) entre la saumureréactive mobile (e.g. eau de formation enrichie en CO2) et la roche encaissante durantl’évolution spatiale et temporelle du CO2, conduisant à des modifications dans la structure despores et par conséquent dans les propriétés d’écoulement du réservoir (e.g. la perméabilité k).Donc, ces changements structuraux peuvent largement contrôler l’injectivité, ainsi que lechamp de pression dans le réservoir et aussi la propagation du CO2. Il demeure ainsi cruciald’explorer les changement dans les propriétés de réservoirs (e.g. structurales ethydrodynamiques) induits durant une injection de CO2 et explicitement les relations existantesentre eux (e.g. k ou surface réactive-Sr versus porosité-φ , k versus hétérogénéité de la roche),afin de développer des outils de modélisation prédictive des processus de transport etréactionnels se produisant durant une injection de CO2 et d’évaluer de façon fiable les risques.Dans le cas des réservoirs carbonatés, l’application des modèles prédictifs de transport réactifdemeure toujours un enjeu, car contrainte par la forte hétérogénéité en leur sein ainsi que parl’incertitude dans la cinétique de réactions des minéraux carbonatés dans ce contexte. Danscette optique, nous avons réalisé des expériences de percolation à travers des échantillons deroches carbonatées dans les conditions thermodynamiques de stockage en profondeur (T =100°C et P =12 MPa). L’évolution de la perméabilité k(t) est suivie au cours desexpériences ; et la variation de la porosité φ (t) est calculée à partir des résultats d’analyseschimiques au ICP-AES des fluides de sortie échantillonnés. L’investigation des modificationsapportées à la structure des pores est réalisée par le biais de la Micro-Tomographie hauterésolution à rayon X, acquise au synchrotron de Grenoble (e.g. ESRF).Dépendant du régime de dissolution, contrôlé par la fabrique de la roche réservoir et lacomposition chimique de la saumuré chargée en CO2 (e.g. PCO2 engagée), on a observéqu’une modification de la structure de la roche peut soit améliorer soit détériorer (résultatatypique en contexte de dissolution) la valeur de la perméabilité k.
https://hal.archives-ouvertes.fr/tel-01142136

tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136/document
https://hal.archives-ouvertes.fr/tel-01142136/file/thesemangane2013.pdf

Éditeur(s) : HAL CCSD Geological Society of London
Résumé : Permo-Triassic rift basins offer important hydrocarbon targets along the Atlantic margins. Their fill is dominated by continental red beds, comprising braided fluvial, alluvial fan, aeolian, floodplain and lacustrine facies. These relatively lightly explored basins span both the Atlantic and Tethyan domains and developed above a complex basement with inherited structural fabrics. Sparse data in offshore regions constrain understanding of depositional geometries and sedimentary architecture, further impeded by their deep burial beneath younger strata, combined with the effects of later deformation during continental breakup. This paper provides results from a multidisciplinary analysis of basins along the Atlantic margin. Regional seismic and well data, combined with geochemical provenance analysis from the European North Atlantic margins, are integrated with detailed outcrop studies in Morocco and Nova Scotia. The research provides new insights into regional basin tectonostratigraphic evolution, sediment fill, and reservoir distribution, architecture and quality at a range of scales. Regional seismic profiles, supported by key well data, indicate the presence of post-orogenic collapse basins, focused narrow rifts and low-magnitude multiple extensional depocentres. Significantly, Permo-Triassic basin geometries are different and more varied than the overlying Jurassic and younger basins. Provenance analysis using Pb isotopic composition of detrital K-feldspar yields new and robust controls on the sediment dispersal patterns of Triassic sandstones in the NE Atlantic margin. The evolving sedimentary architecture is characterized by detailed sedimentological studies of key outcrops of age equivalent Permian-Triassic rifts in Morocco and Nova Scotia. The interplay of tectonics and climate is observed to influence sedimentation, which has significant implications for reservoir distribution in analogue basins. New digital outcrop techniques are providing improved reservoir models, and identification of key marker horizons and sequence boundaries offers a potential subsurface correlation tool. Future work will address source and seal distribution within the potentially petroliferous basins.
Petroleum Geology: From Mature Basins to New Frontiers Proceedings of the 7th Petroleum Geology Conf

hal-00590618
https://hal.archives-ouvertes.fr/hal-00590618

Éditeur(s) : HAL CCSD
Résumé : We present an experimental study of relations between hydraulic properties of clayey rocks and their deformation at bulk and micro scale. The experimentation is based on triaxial deformation of kaolinitic core samples, on permeability measurements, and on several methods of analysis of the microstructure. To produce the samples, remoulded kaolinite material is consolidated by axial loading up to 20 MPa in an oedometric cell. Then, in a triaxial cell, an undrained stress path is applied in order to induce shearing damage in the sample. The permeability of the sample is measured by fluid flow across the sample. Before and after these hydro-mechanical tests, the evolution and the homogeneity of the pore space and moreover the texture of the material are analysed by X-ray tomography, environmental scanning electron microscopy and thermic neutron diffraction. Contrary to expectations, the permeability at the sample scale does not vary significantly, although quite large deformation is reached. The final deformation is heterogeneous, with well-developed shear bands. It appears that the development of compacting and dilating zones generates a heterogeneous permeability field, which results in a negligible variation of the bulk permeability at the sample scale.
International Journal of Rock Mechanics and Mining Science

hal-00496407
https://hal.archives-ouvertes.fr/hal-00496407
DOI : 10.1016/j.ijrmms.2010.04.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Four fibers from banana-trees (leaf, trunk) and coconut-tree (husk, fabric) were examined before their incorporation in cementitious matrices, in order to prepare insulating material for construction. Their botanical compositions have been determined following a method described previously. Thermal degradation of these fibers were studied between 200 and 700 °C under nitrogen gas flow. Temperature of pyrolysis was the experimental parameter investigated. The solid residues obtained were analyzed by classical elemental analysis, Fourier Transform Infra Red (FTIR) spectroscopy and were observed by Scanning Electron Microscopy (SEM). This study has shown (1) the relation between botanical, chemical composition with both localization of fibers in the tree and type of tree; (2) the rapid and preferential decomposition of banana fibers with increasing temperature of pyrolysis and (3) the rough samples are made of hollow fibers.
ISSN: 0960-8524

hal-00809780
https://hal.univ-antilles.fr/hal-00809780
DOI : 10.1016/j.biortech.2005.11.030

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We report on microstructural data obtained by optical microscopy and transmission electron microscopy concerning the crystallographic relationships of serpentine minerals with their host olivine in two contrasting situations. In the first case, mesh-textured lizardite (liz) is developed in a standard 60% serpentinized oceanic harzburgite from the Oman ophiolite where olivine converts to columnar lizardite. The joined columns are perpendicular to the basal plane (001)(liz), corresponding to the pseudofibres observed optically. The plane (001)(liz) is locally parallel to the narrow boundary ol-liz; thus column orientations register the interface of serpentinization. The ol-liz relationships are not strictly topotactic, but reflect preferred cracking orientations in olivine, parallel to (010)(ol). In the second case, antigorite (atg) develops in a rare sample of antigorite schist in a kimberlite from Moses Rock (Colorado Plateau), representative of a suprasubduction-zone mantle wedge. High-resolution transmission electron microscopy (HRTEM) images along [010](atg) show domains of very regular modulation with a 43 center dot 5 A wavelength (m = 17, where m is the number of silicate tetrahedra along the wave), with few defects, indicative of HP-HT antigorite, and also heavily kinked regions as fingerprints of strong tectonic shear. TEM imaging and electron diffraction patterns reveal two topotactic relationships between antigorite and olivine: [100](atg)//[010](ol) and < 100 >(atg)//< 100 >(ol); the planes in contact are (001)(atg)//(100)(ol) and (001)(atg)//(010)(ol), respectively. The [010](atg)//[001](ol) and antigorite lamellae are parallel to the forsterite b-axis. In both cases, the topography of olivine-serpentine interfaces is controlled by open fluid pathways along microcracks oriented according to the anisotropy of the olivine aggregate. In the cases studied, the serpentine aggregate exhibits a preferred orientation inherited from that of the peridotite. These results have some relevance to the seismic anisotropy of serpentinized mantle. Anisotropy of propagation of seismic waves as a result of the olivine fabric is maintained and reinforced with the development of lizardite. Conversely, the development of antigorite produces a trench-parallel fast S-wave polarization and an anisotropy that is lowered at low degrees of serpentinization and then increased with increasing serpentinization.
ISSN: 0022-3530

hal-00456061
https://hal.archives-ouvertes.fr/hal-00456061
DOI : 10.1093/petrology/egp049