Éditeur(s) : HAL CCSD
Résumé : International audience
In most rock mechanical testing devices, the texture developed during deformation is only observed after the failure, and the detailed mapping of cracks and pore structure evolution, just before or after rupture, remains speculative. Computerized X-ray tomography (CT X-ray) offers a way to observe 'in vivo' some characteristics of a tested sample in the course of its deformation. Therefore we developed an X-ray transparent tri-axial cell that was included in a medical purpose X-ray scanner with a volumetric resolution of the order of 1 mm3. This technique is described and applied to a porous calcarenite, which is regularly scanned for porosity evolution during mechanical testing. The experiment is performed at low confining pressure (2-10 MPa). During testing, an axial load is applied until failure and is then progressively decreased. In these experiments, the peak stress is preceded by phase of diffuse dilatancy. After failure localization, the axial stress is unloaded until the stress reaches isotropy. During this unloading phase, the previous diffuse dilatancy is lost due to an elastic relaxation. Then, the stress is completely relaxed. At this moment the dilatancy increases again and the residual dilatancy is larger than that reached at the peak stress. When observed "post mortem" at microscopic scale, the dilatant structures are comprised of cataclastic deformation bands and cracks in some larger crystals.
International Journal of Rock Mechanics and Mining Science

hal-00767563
https://hal.archives-ouvertes.fr/hal-00767563
DOI : 10.1016/j.ijrmms.2012.07.020

Éditeur(s) : HAL CCSD Elsevier
Résumé :  
Microbial-based indicators, such as C and N contents or microbial functions involved in C and N cycles, are currently used to describe the status of soils in disturbed areas. Microbial functions are more accurate indicators but their measurement for studies at the ecosystem level remains problematical because of the huge spatial variability of these processes and, consequently, of the large number of soil samples which must be analyzed. Our goal was to test the capacity of near-infrared reflectance spectroscopy (NIRS) to predict respiration and denitrification but also carbon and nitrogen contents of soils submitted to various procedures of restoration. To achieve this objective, we took advantage of an experiment conducted on a reforestation system established after open-cast gold mining in French Guiana. In this experimental station, plantations of various ages and various soil textures were at our disposal. Our results showed that both plantations and soil texture had a strong impact on the recovery of soil functioning: carbon and nitrogen contents, respiration and denitrification increased with age of plantation and clay content. Calibrations were performed between spectral data and microbial-based indicators using partial least squares regression (PLS). The results showed that C and N contents were accurately predicted. Microbial functions were less precisely predicted with results more accurate on clayey soils than on sandy soils. In clayey soils, perturbed or restored soils and the year of plantation were discriminated very efficiently through principal component analyses of spectral signatures (over 80% of variance explained on the first two axes). Near-infrared spectroscopy may thus be extended to the prediction of functional soil parameters, but the capacity of this method must be strengthened by expending the databases with other soils in other contexts. The possibility of using NIRS provides many opportunities for understanding both the temporal dynamics and the spatial variability of the recovery of key microbial functions during soil restoration.
ISSN: 0929-1393

hal-01032188
https://hal.archives-ouvertes.fr/hal-01032188
DOI : 10.1016/j.apsoil.2007.07.001

Éditeur(s) : HAL CCSD
Résumé : En traitement d'image, avant toute exploitation de résultats d'une segmentation d'image, il est souvent nécessaire de réaliser une opération de fusion. Le but est de créer une partition formée de composantes connexes, modélisant les objets présents dans l'image. La segmentation initiale des images est souvent obtenue par l'exploitation d'attributs de bas-niveau (couleur, texture, forme...). La théorie Gestalt permet de prendre en compte des informations d'un niveau supérieur qui s'appuient sur l'organisation spatiale des objets et groupement d'objets initialement segment'es. Dans cet article, nous proposons une méthode de fusion de régions. L'originalité des travaux repose sur l'ajout d'un nouveau critère qui, associé aux critères Gestalt, permet de prendre en compte les objets jugés d'intérêt par le photographe, c'est-'a-dire les objets aux contours nets. Les régions associées aux objets d'intérêts seront alors préservées alors que les régions floues ou aux contours flous, situées dans l'arrière-plan, auront tendance 'a fusionner entre elles.
Journée du GdR Mathématique de l'Optimisation et Application (MOA)
Saint-François, Guadeloupe

hal-00706538
https://hal.archives-ouvertes.fr/hal-00706538

Éditeur(s) : HAL CCSD
Résumé : International audience
This paper deals with image processing. This study takes place in a segmentation process based on texture analysis. We use the multifractal ap-proach to characterize the textures. More precisely we study a particular multi-fractal spectrum called the large deviation spectrum. We consider two statistical methods to numerically compute this spectrum. The resulting spectrum, com-puted by both methods over an image, is a one dimension spectrum. In the scope of this article, we extend these methods in order to obtain a two dimen-sions spectrum which could be assimilated to an image. This 2D spectrum al-lows a local characterization of the image singularities while a 1D spectrum is a global characterization. Moreover, the computation of the spectrum requires the use of a measure. We introduce here a pre processing based on the gradient to improve the measure. We show results on both synthetic and real world images. Finally, we remark that the resulting 2D spectrum is close to the resulting im-age of an edge detection process while edge detection using one dimension spectrum requires post processing methods. This statement will be used for fu-ture works.
SITIS Proceedings
Hammamet, Tunisia

hal-00602273
https://hal.archives-ouvertes.fr/hal-00602273

Résumé : Ce travail vise à mettre en place un système de fusion de sources d'information basé sur la Théorie des Fonctions de Croyance (TFC) et adapté aux contextes des images forestières. La TFC engendre des temps de calcul importants lorsque la cardinalité du cadre de discernement devient grande. Ainsi, nous avons proposé en premier lieu une méthode de réduction du référentiel de définition permettant d'éviter l'explosion combinatoire en restreignant le calcul sur les hypothèses estimées pertinentes et déterminées à partir des histogrammes des classes issues de la phase d'apprentissage. Ensuite, nous avons proposé des techniques d'estimation de fonctions de masse spectrales, texturales, contextuelles et structurelles. L'information multi-fractale a été utilisée comme signature de texture, ainsi l'image de Hôlder a constitué une source d'information pour l'estimation de la masse texturale. Un autre apport consiste à proposer une approche de transfert de masse basée sur l'information contextuelle, en exploitant l'image des couronnes d'arbres comme une source déduite. L'implémentation d'algorithmes de détection de couronnes d'arbres nous a permis d'extraire des mesures sur les couronnes que nous avons utilisées en tant qu'attributs pour l'estimation des fonctions de masse. Nos expérimentations montrent des taux de classification assez satisfaisants et une adéquation de notre approche de fusion à une classification à l'arbre près
This thesis aims to develop an information source fusion system based on belief functions theory (BFT) and adapted t forest images context (especially high resolution images). Applications of BFT to image classification result in th assignment of each image point to a c1ass or a subset of classes based on the mass functions estimation expressing th belief of an event. BFT leads to significant computation time when the cardinality of the set of definition become large. Thus, we first proposed a method to reduce the frame of discernment in order te avoid the combinatorial explosio by restricting the calculation on the hypotheses of the set of definition deduced from the classes histograms determine from the learning phase. Then, we proposed spectral, texturai, contextual and structural mass functions technique estimation. Multi-fractal information was used as texture signature and Hôlder image has been a source ( information for estimating the texturai mass. Another contribution is the integration of trees crowns image as derive source and the proposai of an approach to mass transfer based on contextual information inside and outside a crown. Th implementation of detection trees crowns algorithms allowed us to extract measurements on trees. These measurement are used as attributes for mass functions estimation. Our experiments and comparisons with other methods show quit satisfactory classification rate with spectral and textural approaches and adequacy of our fusion approach to contextu and structural information for trees classification

http://www.theses.fr/2011AGUY0434/document

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
Garnet growth in high-pressure, mafic garnet granulites formed by dehydration melting of hornblende-gabbronorite protoliths in the Jijal complex (Kohistan palaeo-island arc complex, north Pakistan) was investigated through a microstructural EBSD-SEM and HRTEM study. Composite samples preserve a sharp transition in which the low-pressure precursor is replaced by garnet through a millimetre-sized reaction front. A magmatic foliation in the gabbronorite is defined by mafic-rich layering, with an associated magmatic lineation defined by the shape-preferred orientation (SPO) of mafic clusters composed of orthopyroxene (Opx), clinopyroxene (Cpx), amphibole (Amp) and oxides. The shape of the reaction front is convoluted and oblique to the magmatic layering. Opx, Amp and, to a lesser extent, Cpx show a strong lattice-preferred orientation (LPO) characterized by an alignment of [001] axes parallel to the magmatic lineation in the precursor hornblende-gabbronorite. Product garnet (Grt) also displays a strong LPO. Two of the four < 111 > axes are within the magmatic foliation plane and the density maximum is subparallel to the precursor magmatic lineation. The crystallographic relationship < 111 >(Grt)//[001](Opx,Cpx,Amp) deduced from the LPO was confirmed by TEM observations. The sharp and discontinuous modal and compositional variations observed at the reaction front attest to the kinetic inhibition of prograde solid-state reactions predicted by equilibrium-phase diagrams. The P-T field for the equilibration of Jijal garnet granulites shows that the reaction affinities are 5-10 kJ mol.(-1) for the Grt-in reaction and 0-5 kJ mol.(-1) for the Opx-out reaction. Petrographic and textural observations indicate that garnet first nucleated on amphibole at the rims of mafic clusters; this topotactic replacement resulted in a strong LPO of garnet. Once the amphibole was consumed in the reaction, the parallelism of [001] axes of the mafic-phase reactants favoured the growth of garnet crystals with similar orientations over a pyroxene substrate. These aggregates eventually sintered into single-crystal garnet. In the absence of deformation, the orientation of mafic precursor phases conditioned the nucleation site and the crystallographic orientation of garnet because of topotaxial transformation reactions and homoepitaxial growth of garnet during the formation of high-pressure, mafic garnet-granulite after low-pressure mafic protoliths.
ISSN: 0263-4929

hal-00411323
https://hal.archives-ouvertes.fr/hal-00411323
DOI : 10.1111/J.1525-1314.2008.00789.x

Éditeur(s) : HAL CCSD
Résumé : Diffusion du document : INRA Documentation de Centre, Domaine de Duclos, 97170 Petitt-Bourg (Guadeloupe, France) Diplôme : DEA
il s'agit d'un type de produit dont les métadonnées ne correspondent pas aux métadonnées attendues dans les autres types de produit : DISSERTATION
Because soil respiration representes 80% of ecosystem respiration, it is a major flux between biosphere and atmosphere. We examined the effects of root and litter exclusion on soil CO! efflux (Rsu1) using trenching and litter exclusion in a tropical plantation constituted of trees seedlings installed in 16 mono-specific stands 20 years ago near Kourou, French Guyana. Soil CO2 efflux was measured using an infra red gas analyser (PP System,EGM4 ) at 16 randomly distributed plot in each treatment: control, root exclusion, litter exclusion and both root and litter exclusion. in the plantation. We measured R'1l1during four periods, and we have collected soil samples, litter biomass and measured moisture at 5 cm depth in the soil. Soil CO, efflux varied significantly among species from 2,8±O,7f1mo l. m''. s' (mean ± standard deviation) to 7.4± 1.7fLmol. n'-' . s ' for Qualea rosea and Vochys ia tomentosa, respectively. 1'0 significant correlation was found between RSIlI variability and soil moisture, which is mostly related to soil texture in the experimental site. Soil CO2 efflux was significantly reduced in litter exclusion treatment and root exclusion plots (6 months litter and/or root exclusion) during ail measurements period and for ail species, compared to control plots. The reduction of soil CO, efflux was higher in plot without root than in plot without litter of control plot (42% and 25%, respectively). There was an import ant specific diversity in these reductions . We estimated the contribution of roof respiration (Rr) to total Rso1 by calculating the difference between Rso1 control and Rsn l root exclusion plot corrected for the decomposition of root that were killed following t re n e h in ~. Thus the heterotrophic component of soil carbon efflux accounts for 46% of total carbon efflux (1,9f1 mol. rn" . s•') while root respiration accounts for 54% of soil carbon release (2,3 ~t mo l. m-2 S-I) . Because there was a negative and significant correlation between microbial respiration (Rrn) and C/N of mature leaves it seemed to be possible to predict Rm if we known the mature leaves quality. In addition a good estimate theorical R ~, values from R~, measured in different treatments.
La respiration du sol en représentant une part de 80% de la respiration de l'écosystème apparaît être un flux majeur entre la biosphère et l'atmosphère. Nous avons étudié les effets de l'exclusion racinaire et de la litière sur le flux de CO, du sol (R ~ , ) en utilisant la méthode de " Trench-plots" et de suppression de litière dans une plantation d'arbres tropicaux. Ces arbres, âgés de 20 ans ont été plantés sur un sol uniforme, près de Kourou en Guyane française, en 16 placeaux mono-spécifiques. Pour mesurer les flux de CO2 provenant du sol, nous avons utilisé un analyseur différentiel de gaz infrarouge portable muni d'une chambre. Les mesures ont été faites sur 4 traitements différents tels que : le contrôle, l'exclusion racinaire, l'exclusion de litière et l'exclusion de litière et de racine et ce, répétés sur chacune des 16 placettes mono-spécifiques. Cette étude comporte 4 campagnes de mesures. Nous avons également effectué des prélèvements de sol de litière et nous avons fait des mesures d’humidité de sol à une profondeur de 5 cm. Les flux de C01 du sol varient fortement entre espèces de 2.8±O.7 ~t m o 1. m-2. sol à 7 A± 1. 7 ~t m o l. m•1 sol pour Qua/ev rosea ct Vochysto tomentasa, respectivement. Il n'existe pas de corrélation significative entre les variations de Rw l ct celles de l'humidité du sol (indication sur la texture du sol de la plantation ). Nous avons observé que Rso1 était significativement plus faible dans les placeaux sans racines et/ou sans litière (6 mois après la mise en place de l'expérimentation) pour toutes les campagnes de mesures et pour toutes les espèces que dans les placeaux contrôlés. Cette réduction du flux de CO2 du sol est plus forte dans les "trench-plots " que dans les traitement s d'exclusion de litière avec 42 et 25% respectivement. Un effet "traitement " et un effet "espèce" important expliquent 3 1"/.. ct 13% de la variabilité totale de R~. Nous avons cherché à connaître la contribution des racines dans les valeurs de R""I. en comparant le flux de CO2 provenant du sol sur des "trench -plot s'' au flux de COl provenant du sol dans les placeaux contrôlés . Cette estimation a été corrigée pour prendre en compte la décomposition des racines tuées par les tranchées. Ainsi, la composante appartenant aux micro -organismes représente 46% du flux total de carbone provenant du sol (1.9Jlmo l. m-2 S•I ) alors que la respiration des racines représente 54% du dégagement de carbone (2 ,3~lmol. m ol . 5-La respiration des micro-organismes pourrait être estimée en mesurant le C/N des feuilles matures puisqu'il existe une corrélation significative et négative entre les deux. Enfin les résultats obtenus sur les différents traitements permettent d'obtenir une bonne estimation de la respiration du sol avec un RSIlI théorique corrélé à 66% avec les valeurs réelles mesurées.
https://hal.archives-ouvertes.fr/hal-01189239

hal-01189239
https://hal.archives-ouvertes.fr/hal-01189239
PRODINRA : 18212

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Convergent plate margins typically experience a transition from subduction to collision dynamics as massive continental blocks enter the subduction channel. Studies of high-pressure rocks indicate that tectonic fragments are rapidly exhumed from eclogite facies to mid-crustal levels, but the details of such dynamics are controversial. To understand the dynamics of a subduction channel we report the results of a petrochronological study from the central Sesia Zone, a key element of the internal Western Alps. This comprises two polymetamorphic basement complexes (Eclogitic Micaschist Complex and Gneiss Minuti Complex) and a thin, dismembered cover sequence (Scalaro Unit) associated with pre-Alpine metagabbros and metasediments (Bonze Unit). Structurally controlled samples from three of these units (Eclogitic Micaschist Complex and Scalaro-Bonze Units) yield unequivocal petrological and geochronological evidence of two distinct high-pressure stages. Ages (U-Th-Pb) of growth zones in accessory allanite and zircon, combined with inclusion and textural relationships, can be tied to the multi-stage evolution of single samples. Two independent tectono-metamorphic 'slices' showing a coherent metamorphic evolution during a given time interval have been recognized: the Fondo slice (which includes Scalaro and Bonze rocks) and the Druer slice (belonging to the Eclogitic Micaschist Complex). The new data indicate separate stages of deformation at eclogite-facies conditions for each recognized independent kilometer-sized tectono-metamorphic slice, between ∼85 and 60 Ma, with evidence of intermittent decompression (ΔP ∼ 0*5 GPa) within only the Fondo slice. The evolution path of the Druer slice indicates a different P-T-time evolution with prolonged eclogite-facies metamorphism between ∼85 and 75 Ma. Our approach, combining structural, petrological and geochronological techniques, yields field-based constraints on the duration and rates of dynamics within a subduction channel.
ISSN: 0022-3530

hal-01054335
https://hal.archives-ouvertes.fr/hal-01054335
DOI : 10.1093/petrology/egu029

Éditeur(s) : HAL CCSD Springer/Terra Scientific Publishing Company
Résumé : International audience
This study of the Cajati deposit provides evidence that the ore was neither purely hydrothermal, nor volcanic in origin, as previous workers have proposed. The ores were formed from magnetite-rich magmas, hydrothermally altered and intruded at an indicated crustal depth in excess of 500 m. The mineralogical and textural association between magnetite and magnesioferrite in the carbonatite, and between the titanomagnetite and magnesioferrite-Ti mineralization in the pyroxenite of hedenbergite, seems to be analog mineralizations strongly related to the ionic substitution of Fe2+ by Mg. Relatively high Q ratios (>= 5) for Jacupirangite-pyroxenite may indicate a thermo remanent magnetization (TRM) by the ore during post-metamorphic cooling, however it call also be developed from chemical remanent magnetization (CRM). Vector plots for the pyroxenite samples show reasonably linear and stable magnetic components. The intensity decay Curves show that only two components of magnetizations are likely present. Continuous susceptibility measurements with increasing temperature show that the main magnetic phase seems to be magnetite. Maghemite is probably produced during the cooling process. Susceptibility recorded from low temperature (liquid nitrogen (- 196 degrees C)) to room temperature produces typical Curves. indicating Verwey transition of magnetite. Hysteresis parameters point Out that nearly all values fill in a novel region of the Day plot, parallel to but below magnetite SD + MD mixing curves.
ISSN: 1343-8832

hal-00420922
https://hal.archives-ouvertes.fr/hal-00420922

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : Mantle xenoliths in Pliocene alkali basalts of the eastern Betics (SE Iberia, Spain) are spinel ± plagioclase lherzolite, with minor harzburgite and wehrlite, displaying porphyroclastic or equigranular textures. Equigranular peridotites have olivine crystal preferred orientation (CPO) patterns similar to those of porphyroclastic xenoliths but slightly more dispersed. Olivine CPO shows [100]-fiber patterns characterized by strong alignment of [100]-axes subparallel to the stretching lineation and a girdle distribution of [010]-axes normal to it. This pattern is consistent with simple shear or transtensional deformation accommodated by dislocation creep. One xenolith provides evidence for synkinematic reactive percolation of subduction-related Si-rich melts/fluids that resulted in oriented crystallization of orthopyroxene. Despite a seemingly undeformed microstructure, the CPO in orthopyroxenite veins in composite xenoliths is identical to those of pyroxenes in the host peridotite, suggesting late-kinematic crystallization. Based on these observations, we propose that the annealing producing the equigranular microstructures was triggered by melt percolation in the shallow subcontinental lithospheric mantle coeval to the late Neogene formation of veins in composite xenoliths. Calculated seismic properties are characterized by fast propagation of P waves and polarization of fast S waves parallel to olivine [100]-axis (stretching lineation). These data are compatible with present-day seismic anisotropy observations in SE Iberia if the foliations in the lithospheric mantle are steeply dipping and lineations are subhorizontal with ENE strike, implying dominantly horizontal mantle flow in the ENE-WSW direction within vertical planes, that is, subparallel to the paleo-Iberian margin. The measured anisotropy could thus reflect a lithospheric fabric due to strike-slip deformation in the late Miocene in the context of WSW tearing of the subducted south Iberian margin lithosphere.
ISSN: 0278-7407

Droits : info:eu-repo/semantics/OpenAccess
hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809/document
https://hal.archives-ouvertes.fr/hal-01685809/file/Hidas_et_al-2016-Tectonics.pdf
DOI : 10.1002/2016TC004165

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
How reliable are shear wave splitting measurements as a means of determining mantle flow direction? This remains a topic of debate, especially in the context of subduction. The answer hinges on whether our current understanding of mineral physics provides enough to accurately translate between seismic observations and mantle deformation. Here, we present an integrated model to simulate strain-history-dependent texture development and estimate resulting shear wave splitting in subduction environments. We do this for a mantle flow model that, in its geometry, approximates the double-sided Molucca Sea subduction system in Eastern Indonesia. We test a single-sided and a double-sided subduction case. Results are compared to recent splitting measurements of this region by Di Leo et al. (2012a). The setting lends itself as a case study, because it is fairly young and, therefore, early textures from the slab's descent from the near surface to the bottom of the mantle transition zone--which we simulate in our models--have not yet been overprinted by subsequent continuous steady state flow. Second, it allows us to test the significance of the double-sided geometry, i.e., the need for a rear barrier to achieve trench-parallel subslab mantle flow. We demonstrate that although a barrier amplifies trench-parallel subslab anisotropy due to mantle flow, it is not necessary to produce trench-parallel fast directions per se. In a simple model of A-type olivine lattice-preferred orientation and one-sided subduction, trench-parallel fast directions are produced by a combination of simple shear and extension through compression and pure shear in the subslab mantle.
ISSN: 1525-2027

hal-01053506
https://hal.archives-ouvertes.fr/hal-01053506
DOI : 10.1002/2013GC005032

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
A set of synthetic aggregates, containing mixtures of calcite and muscovite, were compacted with varying uniaxial loads ranging from 20 MPa up to 400 MPa. Their elastic properties have been measured using compressional and shear waves in confining hydrostatic pressures up to 475 MPa. Measured seismic velocities are shown to depend on 1) the ratio of calcite to muscovite, 2) the uniaxial load used during sample manufacturing, and 3) the porosity amount prior to velocity measurements. The matrix framework may also affect the seismic velocities, but this effect is not easily quantifiable. In general, measured seismic velocities decrease with increasing muscovite content and porosity. Elastic properties have been calculated based on texture measurements, which were obtained by neutron diffraction. The calculated velocities are based on the calcite and muscovite single crystal elastic tensors, their orientation distribution functions, and their modal fractions. A large discrepancy is apparent between calculated and measured velocities, where the former always overestimate the actual velocities. Shear waves display less of a difference between calculated and measured values, than do compressional waves, indicating that waves propagating by shearing are less affected by sample porosity and matrix framework. A better agreement between measured and calculated seismic velocities arises when the initial porosity is taken into account, using a differential effective medium model. Seismic anisotropy is evident from both measured and calculated velocities, and is low for samples containing pure calcite, but becomes prominent as the muscovite concentration increases. The intensity of anisotropy further depends on the uniaxial load used during sample compaction and the initial porosity.
ISSN: 0148-0227

hal-00512666
https://hal.archives-ouvertes.fr/hal-00512666
DOI : 10.1029/2009JB006523

Éditeur(s) : HAL CCSD
Résumé : To understand the effect of inherited lithospheric structures on the continental plates deformation process, we have developed a multi scale model that explicitly takes into account an anisotropic viscosity due to the Crystal Preferred Orientation (CPO) of olivine in the mantle by coupling a viscoplastic self-consistent simulation of the deformation at the polycrystalline aggregate to a 3D Finite Element code. Using this tool, we calculate the mechanical behavior of a continental lithosphere submitted to extension for various initial structures. The first set of experiments investigates the deformation of a plate with a homogeneous initial olivine CPO. Results show that the macroscopic anisotropy is strongly dependent on the initial orientation of the olivine CPO relative to the solicitation and to its evolution. The second set of experiments aims to analyze the deformation of a continental plate containing pre-existing lithospheric scale shear zones. These multi-domain models show that the olivine mechanical anisotropy may induce the reactivation of pre-existing lithospheric scale shear zones in a plate submitted to rifting. In both cases, the results shows that the macroscopic mechanic anisotropy induced by the evolution of olivine CPO in the upper mantle is a key parameter to understand the deformation of the continental plates and to explain the observed reactivation of inherited structure from past tectonics events
Afin de comprendre l'effet des structures préexistantes sur la déformation des plaques continentales, nous avons développé une méthode de modélisation mécanique multi-échelle utilisant une viscosité anisotrope induite par les Orientations Préférentielles du Réseau (OPR) des cristaux d'olivine présents dans le manteau. Cette méthode en couple le calcul viscoplastique autocohérent de la déformation d'un agrégat d'olivine à un code éléments finis 3D. Elle a été utilisée pour le calcul du comportement mécanique d'une plaque continentale soumise à une extension. Une première série d'expériences numériques sur l'extension de plaque lithosphérique présentant des OPR initiales d'olivine homogènes a permis de montrer que l'anisotropie mécanique macroscopique est fortement dépendante de l'orientation initiale de l'OPR. La seconde série de simulations analyse l'extension d'une plaque continentale présentant une zone présentant des OPR d'olivine héritées d'un événement tectonique précédant. Les résultats de ces calculs multi-domaines que l'anisotropie mécanique de l'olivine peut expliquer la réactivation des zones de cisaillement héritées lors du rifting. Les résultats obtenus dans les deux séries de modèles montrent que l'anisotropie mécanique macroscopique induite par l'évolution des OPR d'olivine dans le manteau supérieur est un paramètre clé pour la compréhension de la déformation des plaques continentales et pour expliquer la réactivation observée de structures tectoniques, tels que les grands décrochements, lors des épisodes tectoniques ultérieurs.
https://tel.archives-ouvertes.fr/tel-00369463

tel-00369463
https://tel.archives-ouvertes.fr/tel-00369463
https://tel.archives-ouvertes.fr/tel-00369463/document
https://tel.archives-ouvertes.fr/tel-00369463/file/KnollThese09.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In the Tahalgha district (southwestern Hoggar, Algeria), the Cenozoic volcanism has sampled subcontinental mantle beneath two crustal terranes that collided during the Pan-African orogeny: the “Polycyclic Central Hoggar” to the east and the “Western Hoggar” to the west. Two major lithospheric shear zones separate these terranes: the “4°35” and the “4°50” faults. Mantle xenoliths were collected between the two faults and across the 4°35 fault. In addition to a range in equilibrium temperatures and chemical compositions reported elsewhere, the samples show variations in their microstructures and crystallographic preferred orientations. Equilibrium temperatures and geochemical characteristics allow dividing them into low — (LT; 700–900 °C), intermediate — (IT; 900–1000 °C), and high-temperature (HT; 1000–1100 °C) xenoliths. The LT and IT peridotites occur on both sides of the 4°35 fault; they are usually coarse-grained. HT xenoliths are present only east of the 4°35 fault, in the narrow domain stuck between the two faults; they are fine-grained and extensively affected by annealing and melt–rock reactions. Microstructures and crystallographic textures indicate that deformation in the LT- and IT-xenoliths occurred through dislocation creep under relatively high-temperature, low-pressure conditions, followed by post-kinematic cooling. The fine-grained HT-xenoliths were deformed under relatively high-stress conditions before being annealed.Combining microstructural and CPO data with petrological and geochemical informations suggests that: (1) the LT xenoliths are remnants of the Neoproterozoic lithospheric mantle that preserved microstructural and chemical characteristics inherited from the Pan-African orogeny, and (2) the HT xenoliths record localized Cenozoic deformation associated with melt channeling through feed-back processes that culminated in the formation of high-permeability porous-flow conduits. Limited grain-growth in HT xenoliths suggests that advective heating of melt conduits was transient and rapidly followed by thermal relaxation due to conductive heat loss into wall-rock peridotites represented by the IT xenoliths, then by exhumation due to volcanic activity.
ISSN: 0040-1951

hal-01171761
https://hal.archives-ouvertes.fr/hal-01171761
DOI : 10.1016/j.tecto.2014.11.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Sapat peridotite in Kohistan (NW Pakistan) is a 12x1 km sized body of meta-harzburgites, dunites, pyroxenites and meta-gabbros in the hanging wall of the Indus Suture Zone. Field relations, micro-textures, bulk and mineral chemistry document melt-rock reactions producing dunites at the expense of meta-harzburgites, and a consecutive olivine-clinopyroxenite formation from the same melt type. The association of mesa-gabbros, dunites, and pyroxenites is interpreted as a crust-mantle transition zone produced by the percolation of highly depleted primitive arc melt. The meta-harzburgites represent large portions of refractoty mantle that have suffered melt extraction and metasomatism prior to their interaction with the dunite-forming primitive arc melt and the establishment of the crust-mantle transition zone. Uncommon vein assemblages in the dunites that include Cr-clinochlore, calcite and olivine document a late percolation of slab-related, volatile-rich fluids. Taking into account the highly refractory composition of the Sapat mantle, its structural position, the evidence for interaction with highly depleted arc melts and the sub-solidus interaction with volatile-rich arc fluids, the Sapat ultramafic rocks are interpreted as being derived from the frontal Kohistan arc, representing a crust-mantle transition formed by arc magmatism.
ISSN: 0024-4937

hal-00424515
https://hal.archives-ouvertes.fr/hal-00424515
DOI : 10.1016/j.lithos.2008.07.004

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We have analyzed the microstructures and crystal preferred orientations (CPO), and calculated the seismic properties of 53 mantle xenoliths from four localities within the North Tanzanian Divergence of the East African rift: two within the rift axis and two in the transverse volcanic belt. Olivine OH concentrations were measured in 15 xenoliths.Most samples have harzburgitic to dunitic compositions and high olivine Mg#. Microstructures and olivine CPO patterns vary strongly depending on the location. In-axis peridotites display mylonitic to porphyroclastic microstructures, which record recent deformation by dislocation creep. Highly stretched orthopyroxenes in mylonites indicate that the deformation was initiated under high stress and probably low temperature. Orthopyroxene replacement by olivine in mylonitic and porphyroclastic peridotites suggest syn-kinematic melt–rock reactions and further deformation under near-solidus conditions. Exsolutions in orthopyroxene imply significant cooling between melt-assisted deformation and xenolith extraction. Late metasomatism is evidenced by the occurrence of veins crosscutting the microstructure and interstitial clinopyroxene and phlogopite. Axial-[100] olivine CPOs predominate, suggesting activation of the high temperature, low pressure [100] {0kl} slip systems and, probably, transtensional deformation. In the volcanic belt, Lashaine peridotites display very coarse-granular textures, indicating deformation by dislocation creep under low deviatoric stress conditions followed by annealing. Axial-[010] olivine CPOs are consistent with transpressional deformation or simultaneous activation of the [100](010) and [001](010) slip systems. Intermediate microstructures and CPOs in Olmani suggests heterogeneous deformation within the volcanic belt. Olivine OH concentrations range between 2 and 12 ppm wt. H2O. No systematic variations are observed between in- and off-axis samples. Maximum P wave azimuthal anisotropy (AVp) ranges between 3.3 and 18.4%, and the maximum S wave polarization anisotropy (AVs) between 2.3 and 13.2%. Comparison between seismic properties of in-axis peridotites and SKS splitting data suggests transtensional deformation in the lithospheric mantle beneath the rift.
ISSN: 0040-1951

hal-01121552
https://hal.archives-ouvertes.fr/hal-01121552
DOI : 10.1016/j.tecto.2014.11.011

Éditeur(s) : HAL CCSD
Résumé : International audience
This paper deals with a comparison of different colour space in order to improve high resolution images classification. The background of this study is the measure of the agriculture impact on the environment in islander context. Biodiversity is particularly sensitive and relevant in such areas and the follow-up of the forest front is a way to ensure its preservation. Very high resolution satellite images are used such as QuickBird and IKONOS scenes. In order to segment the images into forest and agriculture areas, we characterize both ground covers with colour and texture features. A classical unsupervised classifier is then used to obtain labelled areas. As features are computed on coloured images, we can wonder if the colour space choice is relevant. This study has been made considering more than fourteen colour spaces (RGB, YUV, Lab, YIQ, YCrCs, XYZ, CMY, LMS, HSL, KLT, IHS, I1I2I3, HSV, HSI, etc.) and shows the visual and quantitative superiority of IHS on all others. For conciseness reasons, results only show RGB, I1I2I3 and IHS colour spaces.
SPIE Remote Sensing Proceedings
Cardiff, United Kingdom

hal-00602277
https://hal.archives-ouvertes.fr/hal-00602277

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We analyzed twelve fault gouge samples from the Bogd fault in south-western Mongolia to understand the origin and behavior of clay minerals. The investigation relies on x-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high energy synchrotron x-ray diffraction methods to investigate microstructure and preferred orientation. Smectite (montmorillonite), illite-smectite mixed layers, illite-mica and kaolinite are the major clay components, in addition to quartz and feldspars, which are present in all samples. The observations suggest that the protoliths and the fault rocks were highly altered by fluids. The fluid-rock interactions allow clay minerals to form, as well as alter feldspars to precipitate kaolinite and montmorillonite. Thus, newly formed clay minerals are heterogeneously distributed in the fault zone. The decrease of montmorillonite component of some of the highly deformed samples also suggests that dehydration processes during deformation were leading to illite precipitation. Based on synchrotron x-ray diffraction data, the degree of preferred orientation of constituent clay minerals is weak, with maxima for (001) ranging from 1.3 to 2.6 multiples of a random distribution (m.r.d). Co-existing quartz and feldspars have random orientation distributions. Microstructure and texture observations of the gouges from the foliated microscopic zone, alternating with micrometric isotropic clay-rich area, also indicate that the Bogd fault experienced brittle and ductile deformation episodes. The clay minerals may contribute to a slip weakening behavior of the fault.
ISSN: 0191-8141

insu-00667194
https://hal-insu.archives-ouvertes.fr/insu-00667194
DOI : 10.1016/j.jsg.2011.10.006

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
The Lanzo peridotite massif is a fragment of oceanic lithosphere generated in an ocean-continent transition context and eclogitized during alpine collision. Despite the subduction history, the massif has preserved its sedimentary oceanic cover, suggesting that it may have preserved its oceanic structure. It is an exceptional case for studying the evolution of a fragment of the lithosphere from its oceanization to its subduction and then exhumation. We present a field and petrological study retracing the different serpentinization episodes and their impact on the massif structure. The Lanzo massif is composed of slightly serpentinized peridotites (<20% serpentinization) surrounded by an envelope of foliated serpentinites (100% serpentinization) bordered by oceanic metabasalts and metasedimentary rocks. The limit between peridotites and serpentinites defines the front of serpentinization. This limit is sharp: it is marked by the presence of massive serpentinites (80% serpentinization) and, locally, by dykes of metagabbros and mylonitic gabbros. The deformation of these gabbros is contemporaneous with the emplacement of the magma. The presence of early lizardite in the peridotites testifies that serpentinization began during the oceanization, which is confirmed by the presence of meta-ophicarbonates bordering the foliated serpentinite envelope. Two additional generations of serpentine occur in the ultramafic rocks. The first is a prograde antigorite that partially replaced the lizardite and the relict primary minerals of the peridotite during subduction, indicating that serpentinization is an active process at the ridge and in the subduction zone. Locally, this episode is followed by the deserpentinization of antigorite at peak P-T (estimated in eclogitized metagabbros at 2-2.5 GPa and 550-620 °C): it is marked by the crystallization of secondary olivine associated with chlorite and/or antigorite and of clinopyroxene, amphibole and chlorite assemblages. A second antigorite formed during exhumation partially to completely obliterating previous textures in the massive and foliated serpentinites. Serpentinites are an important component of the oceanic lithosphere generated in slow to ultraslow spreading settings, and in these settings, there is a serpentinization gradient with depth in the upper mantle. The seismic Moho limit could correspond to a serpentinization front affecting the mantle. This partially serpentinized zone constitutes a less competent level where, during subduction and exhumation, deformation and fluid circulation are localized. In this zone, the reaction kinetics are increased and the later steps of serpentinization obliterate the evidence of this progressive zone of serpentinization. In the Lanzo massif, this zone fully recrystallized into serpentinite during alpine subduction and collision. Thus, the serpentinite envelope represents the oceanic crust as defined by geophysicists, and the sharp front of serpentinization corresponds to an eclogitized seismic palaeo-Moho.
ISSN: 0263-4929

hal-00823051
https://hal.archives-ouvertes.fr/hal-00823051
DOI : 10.1111/jmg.12008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Oisans Massif, located in the external zones of the western Alps, experienced significant shortening during the Alpine collision. While a series of major top-to-the west shear zones was recently described, the general low grade of the metamorphism has not attracted much petrological and geochronological studies. This paper provides combined temperature and age constraints on the evolution of the Oisans Massif. Temperature was estimated with the Raman Spectrometry of Carbonaceous Material (RSCM) method and chlorite geothermometry. Maximum temperature reached by the Mesozoic cover (Tmax) from Grenoble to the Galibier pass (E-W) and from Saint Jean de Maurienne to Embrun (N-S) yielded almost constant ca. 330 °C temperatures all through the Massif. Temperatures however strongly decrease either westward towards the top of the Vercors sedimentary sequence or eastward towards the Penninic Frontal Thrust. Age constraints were retrieved using 40Ar/39Ar in situ analyses performed on variously strained samples from Alpine shear zones. Over strain gradients, incipient Alpine recrystallizations progressively develop at the expense of former Variscan parageneses. A combined textural and EPMA approach permitted to identify newly formed chlorite and phengite that unequivocally grew in response to deformation or to low grade metamorphism. Chlorites recorded temperatures from ca. 350–150 °C during the activity of shear zones. In parallel, 40Ar/39Ar in situ experiments enabled dating deformation using both synkinematic phengites crystallized below the closure temperature of white-micas and former Variscan muscovite whose isotopic system have been, at least partially re-opened. Activity of top-to-the-west shear zones responsible for the shortening and thickening of the Oisans massif thus occurred between 34 and 33 and 25 Ma. Integrating these new age-constraints, Tmax estimates, and published geological data on the Oisans Massif and neighbouring areas allow proposing a new shortening scenario for the external zones. From ca. 34–33 Ma, the Oisans Massif was buried as a rigid block below more internal units and reached a temperature of ca. 330 °C. Shearing progressively localized along a series of top-to-the-W shear zones in the basement until 25 Ma. Deformation then localized along a major thrust at the base of the ECM massif and propagated along the basement-cover interface below the Vercors massif after 16 Ma.
ISSN: 0264-3707

Droits : info:eu-repo/semantics/OpenAccess
insu-01093878
https://hal-insu.archives-ouvertes.fr/insu-01093878
https://hal-insu.archives-ouvertes.fr/insu-01093878/document
https://hal-insu.archives-ouvertes.fr/insu-01093878/file/GEOD1326RA.pdf
DOI : 10.1016/j.jog.2014.09.004