Éditeur(s) : HAL CCSD
Résumé : Both short-term and long-term morphodynamics of sand barrier systems forced by moderate storm conditions have been studied significantly in the literature. However, the dynamics of the emerged beach -- from a seaside water depth of ~ 1.5 metres below the lowest tide to the back-barrier -- impacted by typhoons remain scarcely documented. This study focuses on the analysis and a better understanding of the morphologic changes of such an emerged beach, when it is forced by one typhoon, several typhoons or the combination of a summer season of typhoons and a winter season of Monsoon wave/ wind conditions. The monitoring of near-shore hydrodynamics and beach morphodynamics was performed in the Wan-Tzu-Liao sand barrier from November 2011 to August 2012. Waves, currents and water level were measured at an offshore buoy (Cigu buoy; 18 m of water depth; 1.5 km seaward the studied zone), a current profiler (4 m of water depth), and a serie of pressure sensors deployed along a cross-shore section from the lower intertidal zone up to the eolian dune. Tide was obtained from a tide gauge inside the lagoon and wind conditions were obtained respectively from an inland station and the offshore Cigu buoy. Morphodynamic changes were monitoring thanks to DGDPS surveys performed on a grid including a 300 meters long portion of sand barrier extending from the subtidal zone to the back-barrier, as well as along two cross-shore and two long-shore profiles located within the grid. Surveys were performed each week during winter and just before and after each storm during the typhoons summer season. This field methodology provided a new and very robust dataset in order to quantify sand barrier dynamics exposed to high-energy events at various time scales. Amongst the eight typhoons recorded, TALIM is the most significant and representative. Offshore wave height reached 10.34 m (Tp = 14.6 s) at Cigu buoy and 2.3 m in 4 m of water depth. Morphological changes recorded 6 m of retreat for the dune front, a 20 m large dune breaching and the occurence of a wash-over fan in the lagoon. These changes form a well-known morphodynamic responses to moderate storms. More surprisingly, TALIM drove a significant nourishment of the supratidal zone, as well as a positive sand balance on the whole sand barrier. Five other typhoons resulted in the same type of morphological responses while two typhoons resulted in a strong erosion of the whole emerged beach. During winter and spring (moderate wave conditions and strong Monsoon winds), sand moved from the beach front to the back-barrier. For the whole year, the sand barrier recorded a 12 m landward migration concomitantly with a 12 m widening without abrasion of the dune elevation.
American Geophysical Union, Fall Meeting 2013

hal-01012312
https://hal.archives-ouvertes.fr/hal-01012312

Éditeur(s) : HAL CCSD Federation of American Society of Experimental Biology
Résumé : International audience
Testes of most male mammals present the particularity of being externalized from the body and are consequently slightly cooler than core body temperature (4-8 degrees C below). Although, hypothermia of the testis is known to increase germ cells apoptosis, little is known about the underlying molecular mechanisms, including cold sensors, transduction pathways, and apoptosis triggers. In this study, using a functional knockout mouse model of the cold and menthol receptors, dubbed transient receptor potential melastatine 8 (TRPM8) channels, we found that TRPM8 initiated the cold-shock response by differentially modulating cold- and heat-shock proteins. Besides, apoptosis of germ cells increased in proportion to the cooling level in control mice but was independent of temperature in knockout mice. We also observed that the rate of germ cell death correlated positively with the reactive oxygen species level and negatively with the expression of the detoxifying enzymes. This result suggests that the TRPM8 sensor is a key determinant of germ cell fate under hypothermic stimulation.Borowiec, A.-S., Sion, B., Chalmel, F., Rolland, A. D., Lemonnier, L., De Clerck, T., Bokhobza, A., Derouiche, S., Dewailly, E., Slomianny, C., Mauduit, C., Benahmed, M., Roudbaraki, M., Jegou, B., Prevarskaya, N., Bidaux, G. Cold/menthol TRPM8 receptors initiate the cold-shock response and protect germ cells from cold-shock-induced oxidation.
ISSN: 0892-6638

hal-01390973
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01390973
DOI : 10.1096/fj.201600257R
PUBMED : 27317670

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimize cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: (1) providing data to optimise the settings for a given operation (batch approach) and (2) building predictive models that could be the basis of an online control systems for the machining processes (interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With potential industrial applications in focus, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Though not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technologic knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003/document
https://hal.archives-ouvertes.fr/hal-00876003/file/LABOMAP_Holzforschung_2009_denaud.pdf
ENSAM : http://hdl.handle.net/10985/7419

Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers (IEEE)/Optical Society of America(OSA)
Résumé : International audience
Nanometric displacement measurements by Extrinsic Fiber Fabry-Perot interferometers (EFPI) is extremely susceptible to external environmental changes. Temperature, in particular, has a remarkable influence on the optical power and wavelength of the laser diode in use, in addition to the thermal expansion of the mechanical structure. In this paper we propose an optimization of the EFPI sensor in order to use it for very long-term (more than one year) and for high-precision displacement measurements. For this purpose, a real time and adaptive estimation procedure based on a homodyne technique and a Kalman filter is established. During a sinusoidal laser diode current modulation, the Kalman filter provides a correction of the amplitude drift caused by the resultant optical power modulation and external perturbations. Besides, stationary temperature transfer operators are estimated via experimental measurements to reduce the additive thermal noise induced in the optical phase and mechanical components.
ISSN: 0733-8724

hal-00876339
https://hal.archives-ouvertes.fr/hal-00876339
DOI : 10.1109/JLT.2012.2194476

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context: Woodcutting is a very old technology but scientific research is scarce on the subject. In the last 50 years much work on basic mechanisms as well as industrial processes has been done in France. Aims: The specific nature of wood introduces strong differences between wood and metal cutting processes. The paper focuses on French teams' contributions. Results: The basic aspects of the tool–material interaction for different basic modes in woodcutting are highlighted. In primary conversion such as sawing, veneer cutting or green wood chipping, huge progress comes from automation and the possibility of linking the process to log and product quality through new sensors. In secondary processing much has been done on the links between the cutting process, surface qualification and the properties of these surfaces for further processing, such as gluing or coating. Tool wear depends on the cutting process, timber quality, and species. Trade-offs are required in tool technology and coating technologies may improve tool life. Conclusion: A large amount of knowledge and innovation has come from 50 years of worldwide research effort, with France being particularly active in this period. The transfer of skills from metals cutting industry was often a key, but much is needed to move closer to both metal cutting sector and woodcutting skills among craftsmen.
ISSN: 1286-4560

hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156/document
https://hal.archives-ouvertes.fr/hal-01135156/file/Wood_machining_focus_French_research_Thibaut_al_2015.pdf
DOI : 10.1007/s13595-015-0460-2

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : Contaminant migration in aquifers is one of the most debated issues in hydrogeology, as most experimental results display large deviations from the standard (asymptotic) Fickian dispersion theories. Multi-scale investigation and high-resolution sensors are required to determine the origin of non-asymptotic dispersion and validate models. For this, a set of multi-scale Single-Well Injection-Withdrawal (SWIW) tracer tests using a new dual-packer probe CoFIS, including a high resolution optical sensor TELog, are presented. When compared to standard techniques such as salinity measurements, it is shown that high-resolution optical measurements allow an improved characterization of the long-lasting non-asymptotic dispersion mechanisms.
ISSN: 1631-0713

hal-00445250
https://hal.archives-ouvertes.fr/hal-00445250
DOI : 10.1016/j.crte.2009.07.012

Éditeur(s) : HAL CCSD
Résumé : International audience
The present research work is a part of the KUNSHEN Franco-Taiwanese research project which aims at investigating the hydro/morphodynamics of barrier islands driven by typhoon events. This study focuses on the impact of the Talim tropical storm on the Wan-tzu-liao sand barrier (Taiwan) in terms of water level rising and watertable overheight. In-situ measurements are provided by a cross-shore network of pressure sensors extended from the intertidal zone to the top of the barrier. Extreme offshore wave conditions are encountered during Talim, with significant wave height greater than 10m at the storm peak. It is shown that measured setups are smaller than those predicted by usual empirical parameterization. Groundwater dynamics is strongly affected by the storm, with watertable overheight of the order of one meter under the barrier top. Watertable dynamics is influenced by waves, tides and rainfalls.
Coastal Dynamics 2013

hal-00831573
https://hal.archives-ouvertes.fr/hal-00831573

Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : On the basis of an existing multiparameter borehole fluid sensor(p, T Cw, pH, Eh), a new downhole tool designed for 200 bars and 75 degrees C was developed to measure the spontaneous electrical potential in situ with great precision (better than a mu V). To this end, the new sensor is based on the use of unpolarizable Pb/PbCl2 electrodes either at the surface or downhole. In situ testing has demonstrated a capacity to identify several subsurface sources of natural electrical potential such as diffusion ones (membrane potential in the presence of clays, Fickian processes due to pore fluid salinity gradients), or else the electrokinetic mechanisms with gradients in pore fluid pressure. As a consequence, Multi-Sensors Electrical Tool (MuSET) might be used as an "electrical flow meter" sensitive to both horizontal and vertical fluid flow in a vertical borehole.
ISSN: 1631-0713

hal-00445251
https://hal.archives-ouvertes.fr/hal-00445251
DOI : 10.1016/j.crte.2009.07.009

Éditeur(s) : HAL CCSD
Résumé : International audience
Acute viral hepatitis results from an inefficient innate immune response to clear the virus and a delayed immune adaptive response. Murine hepatitis virus (MHV) infection represents a unique animal model to identify new escape mechanisms in liver of innate immune responses. The objective of this study was to identify early disorders in TLRs, helicases, cytokines and chemokines favoring the development of a fulminant hepatitis. Groups of C57BL/6 WT and TLR2-/- mice were infected with highly hepatotropic MHV3 and/or weakly hepatotropic MHV-A59 viruses. Histopathological analysis of liver and mRNA expression levels of viral nucleoprotein, viral sensors, interferons, cytokines and chemokines assessed by RT-qPCR were done in the first 3 days of infection. The results showed that liver damages, viral replication and mRNA levels of TLR-2, TLR-3, RIG-1, MDA-5, IL-33, IFN-b, CXCL1, CXCL9, CXCL-10, CXCL-11, CCL3, CCL5, IL-6 and TNF-a increased higher or appeared sooner in MHV3-infected WT than in MHV-A59 and TLR2-/- mice. To address the role of hepatocytes in TLR2-dependent viral replication and innate immune factors, in vitro viral infections were performed on FL83B cells. The results showed that viral replication and mRNA levels of TLR-2 and IL-6 occurred sooner than those of other innate immune parameters. Moreover, blockade of TLR-2 by siRNA decreased IFN-b, TNF-a, CXCL-1, CXCL-10 and CCL-2 expression in infected hepatocytes and also inhibited the viral replication of MHV-A59, and at a lesser extent of MHV3, suggesting that TLR-2 signaling promotes simultaneously the viral replication and the production of innate immune factors in hepatocytes, exacerbating viral hepatitis.
Frontiers of Immunology
Milan, Italy

hal-01118155
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01118155
DOI : 10.3389/conf.fimmu.2013.02.00648

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : International audience
When fish larvae recruit back to a reef, chemical cues are often used to find suitable habitat or to find juvenile or adult conspecifics. We tested if the chemical information used by larvae was intentionally produced by juvenile and adult conspecifics already on the reef (communication process) or whether the cues used result from normal biochemical processes with no active involvement by conspecifics (“spying” behavior by larvae). Conspecific chemical cues attracted the majority of larvae (four out of the seven species tested); although while some species were equally attracted to cues from adults and juveniles (Chromis viridis, Apogon novemfasciatus), two exhibited greater sensitivity to adult cues (Pomacentrus pavo, Dascyllus aruanus). Our results indicate also that spying cues are those most commonly used by settling fishes (C. viridis, P. pavo, A. novemfasciatus). Only one species (D. aruanus) preferred the odour of conspecifics that had had visual contact with larvae (communication).
ISSN: 1631-0691

hal-01212899
https://hal-univ-perp.archives-ouvertes.fr/hal-01212899
DOI : 10.1016/j.crvi.2015.05.004