Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Silane coating of fibers is a promising process for improving durability and adhesion of vegetable fibers used as reinforcement material in a cementitious matrix. The work presented in this paper gives an insight into the effect of combining pyrolysis treatment with silane treatment. Indeed, this study focuses on silane treatment of unpyrolyzed and pyrolyzed sugar cane bagasse fibers with an alkyltrialkoxysilane (RSi(OR′)3), S1 or a dialkyldialkoxysilane (R2Si(OR″)2), S2. The silane solutions used vary from 0.5% to 8% by volume. This paper describes the effect of two silane compounds on parameters such as the porosity, dimension, morphology and hygroscopic character of silane-coated sugar cane bagasse fibers. Preliminary studies on natural fiber reinforced composite setting time show the importance of the silane chemistry/structure, for fiber treatments with silane solution containing up to 6% (volume percent) silane. In the case of composites reinforced with unpyrolyzed bagasse fibers, setting time increases with silane coating. Combining pyrolysis and silane treatment improve the water resistance of the fibers, which become more hydrophobic.
ISSN: 1359-835X

hal-00809830
https://hal.univ-antilles.fr/hal-00809830
DOI : 10.1016/j.compositesa.2008.05.013

Éditeur(s) : HAL CCSD
Résumé : International audience
A fiber interferometer interfaced to 3 geo-mechanical elements is presented for applications in geophysics. The fiber sensor is based on an extrinsic fiber Fabry-Perot interferometer (EFFPI) which incorporates a modulation scheme to lock the interferometer at quadrature and to enable displacement measurements below a quarter of the interrogating wavelength. It operates over a relatively large frequency dynamic of ~500000 with a precision better than 2 nm. The fiber interferometer is next interfaced to a differential hydrostatic long baseline inclinometer, a 3-axis borehole tiltmeter and a single-axis seismometer, respectively. Results obtained demonstrate that the fiber interferometrically-interrogated instruments exhibit performances equivalent to or even surpassing those of the reference instruments employed for comparison during their deployment to an underground test site since March 2012. Keywords—modulation-based extrinsic fiber Fabry-Perot interferometer; fiber optique hydrostatic inclinometer; fiber optique borehole tiltmeter; fiber optique seismometer
IEEE SENSORS 2015
Busan, South Korea

hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963/document
https://hal.archives-ouvertes.fr/hal-01265963/file/HCS3.pdf
DOI : 10.1109/ICSENS.2015.7370316

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Four fibers from banana-trees (leaf, trunk) and coconut-tree (husk, fabric) were examined before their incorporation in cementitious matrices, in order to prepare insulating material for construction. Their botanical compositions have been determined following a method described previously. Thermal degradation of these fibers were studied between 200 and 700 °C under nitrogen gas flow. Temperature of pyrolysis was the experimental parameter investigated. The solid residues obtained were analyzed by classical elemental analysis, Fourier Transform Infra Red (FTIR) spectroscopy and were observed by Scanning Electron Microscopy (SEM). This study has shown (1) the relation between botanical, chemical composition with both localization of fibers in the tree and type of tree; (2) the rapid and preferential decomposition of banana fibers with increasing temperature of pyrolysis and (3) the rough samples are made of hollow fibers.
ISSN: 0960-8524

hal-00809780
https://hal.univ-antilles.fr/hal-00809780
DOI : 10.1016/j.biortech.2005.11.030

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : International audience
This paper presents the effects of chemical and thermal treatments on the strength of vegetable fibers that were being considered as reinforcements in cementitious matrix composites for affordable housing. These include vegetable fibers extracted from banana trunks and sugar cane residues. The results suggested that pyrolysis increased the fiber strength, at least by a factor three. Acid attack generally degraded the strengths, while alkali attack had only a limited effect. Pyrolyzed banana leaves, coconut coir, and coconut sheaths fibers were also tested. The implications of the results were discussed for the development of strong cementitious matrix composites.
ISSN: 1042-6914

hal-00809827
https://hal.univ-antilles.fr/hal-00809827
DOI : 10.1080/10426910601063386

Éditeur(s) : HAL CCSD American Geophysical Union (AGU) AGU and the Geochemical Society
Résumé : International audience
To study how an impacting plume modifies the mantle lithosphere, we analyzed the microstructures and crystal preferred orientations (CPO) of 29 peridotites and 37 pyroxenites that sample the mantle root of the Ontong Java Plateau (OJP) from 60 to 120 km depth. The peridotites show a strong compositional variability, but homogeneous coarse granular to tabular microstructures, except for those equilibrated at the shallowest and deepest depths, which are porphyroclastic. All peridotites have clear olivine CPO, with dominant fiber-[010] patterns. Low intragranular misorientations and straight grain boundaries in olivine suggest that, above 100 km depth, annealing often followed deformation. Calculated density and P wave velocities of the peridotites decrease weakly with depth. S wave velocities decrease faster, resulting in increasing Vp/Vs ratio with depth. Calculated densities and seismic velocity profiles are consistent with those estimated for normal mantle compositions under a cold oceanic geotherm. Enrichment in pyroxenites may further increase seismic velocities. The calculated seismic properties cannot therefore explain the low S waves velocities predicted by Rayleigh wave tomography and ScS data in the mantle beneath the OJP. Calculated P and S waves anisotropy is variable (2–12%). It is higher on average in the deeper section of the lithosphere. Because olivine has dominantly [010]-fiber CPO patterns, if foliations are horizontal, vertically propagating S waves and Rayleigh waves will sample very weak anisotropy in the OJP mantle lithosphere. Moreover, if the orientation of the lineation changes with depth, the anisotropy-induced contrast in seismic properties might produce an intralithospheric reflector marking the stratification of the OJP mantle root.
ISSN: 1525-2027

hal-01116428
https://hal.archives-ouvertes.fr/hal-01116428
DOI : 10.1002/2014GC005452

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : International audience
This work evaluates the influence of three different intensities of refinement of sisal pulp and the effect of accelerated aging cycles on the behavior of composites. Fiber-cements were prepared by the slurry de-watering method and pressing as a crude simulation of the Hatschek process. Mechanical behavior of composites was evaluated by four-point bending test at 28 days, and after 50 and 100 wet/dry cycles. Refinement of pulp and aging have increased the strength and bulk density of composites and decreased the toughness and porosity. The best mechanical performance after aging was achieved for samples with highly refined fibers.
ISSN: 1042-6914

hal-00809817
https://hal.univ-antilles.fr/hal-00809817
DOI : 10.1080/10426910601062065

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Meconium is the earliest stool of newborns, and is a complex matrix that reflects the degree of exposure of the fetus to xenobiotics. To investigate fetal exposure to volatile organic compounds, an analytical method was developed to identify and quantify BTEX (benzene, toluene, ethylbenzene, and o,m,p-xylene) and two chlorinated solvents (trichloroethylene and tetrachloroethylene) in meconium. Headspace-solid-phase microextraction coupled with gas chromatography-mass spectrometry was selected because it is simple, sensitive, can be automated, and requires no extensive sample preparation. Several extraction variables were optimized (fiber type, incubation time, temperature of fiber, and use of salt). Because meconium is a complex matrix, quantification by SPME was considered carefully because of potential interference, for example competitive adsorption. Calibration in water was compared with calibration in meconium using external and internal methods (with isotope-labeled compounds). In meconium, limits of quantification were determined to be in the range 0.064-0.096 ng g(-1) for the investigated compounds. All target compounds were determined in "real-case" meconium samples.
ISSN: 1618-2642

hal-01064967
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01064967
DOI : 10.1007/s00216-014-7836-2
PUBMED : 24838489

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We explore the relations between deformation, annealing, and melt percolation during rifting and the effect of these processes on seismic anisotropy by analyzing the microstructures and crystal preferred orientations (CPO) in a suite of mantle xenoliths from Mega, in the southern end of the Ethiopian rift. Previous geochemical studies on these xenoliths showed evidence for interactions with variable melt types and volumes during the rifting process. The peridotites have dominantly coarse-porphyroclastic microstructures, but coarse granular or partially recrystallized microstructures also occur. The olivine CPO, characterized by orthorhombic to fiber-[100] patterns and moderate intensities, the common occurrence of (100) tilt walls, and the predominance of <0vw> rotation axes accommodating low angle misorientations in olivine support deformation by dislocation creep with dominant activation of the [100](010) system. Annealing (static recrystallization) of variable intensity followed this deformation. Modal enrichment in pyroxenes in > 60% of the studied peridotites corroborates extensive, but spatially heterogeneous reactive melt percolation leading to refertilization of the lithospheric mantle beneath the southern Ethiopian rift. The common interstitial shapes of the pyroxenes and lack of correlation between the pyroxenes and the olivine CPOs in many samples suggest that part of the refertilization is post-kinematic. However, there is no simple relation between reactive melt percolation and annealing of the olivine deformation microstructure. Comparison with data from other xenolith localities points to changes in the metasomatic imprint in the lithospheric mantle along the East African rift system correlated with the evolution in the rift maturity. Seismic properties averaged over all samples show typical lithospheric mantle patterns with fast propagation of P- and polarization of the fast S-waves parallel to the lineation. The anisotropy is moderate (< 6% for P-waves and < 4% for S-waves), implying that aligned melt must contribute to the strong seismic anisotropy measured in the Main Ethiopian rift, north of Mega.
ISSN: 0040-1951

hal-01355918
https://hal.archives-ouvertes.fr/hal-01355918
DOI : 10.1016/j.tecto.2016.05.027

Éditeur(s) : HAL CCSD AIMS Press
Résumé : International audience
In this article, we obtain sucient conditions to obtain finite time blowup in a system of two coupled nonlinear Schrödinger (NLS) equations in the critical case. This system mainly considered here in dimension 2, couples one equation including gain and the other one including losses, constituting a generalization of the model of pulse propagation in birefringent optical fibers. In the spirit of the seminal work of Glassey, the proofs used the virial technique arguments.
ISSN: 2473-6988

hal-01492062
https://hal.univ-antilles.fr/hal-01492062
DOI : 10.3934/Math.2017.1.195

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The subcontinental lithospheric mantle evolves through time due to tectonic events and processes as static recrystallization and melt percolation. To constrain the extent of these processes in the South Patagonian subcontinental mantle lithosphere we performed a microstructural and Electron Backscattered Diffraction (EBSD) study of a suite of 35 peridotite xenoliths brought to the surface by Plio-Pleistocene alkaline volcanic rocks from Gobernador Gregores and Pali Aike. All samples show a well-developed olivine and pyroxene crystallographic preferred orientation (CPO), consistent with deformation by dislocation creep with dominant activation of [100]{0kl} in olivine. The coarse granular or tabular textures and the low density of intracrystalline deformation features indicate that deformation was followed by annealing under static conditions. The xenoliths also show microstructural evidence of multiple episodes of reactive melt percolation. Neither annealing nor melt percolation erased the olivine CPO, which has [010]-fiber, [100]-fiber and orthorhombic patterns in Pali Aike xenoliths and essentially [010]-fiber and orthorhombic patterns in Gobernador Gregores xenoliths. Seismic properties calculated based on the CPO and modal compositions are, however, rather homogeneous, with fast S-wave polarization and P-wave propagation parallel to the [100] olivine axis. The variation in the olivine CPO solely changes the minimum S-wave birefringence direction, which is normal to the foliation for axial-[010] olivine CPO. Average samples for the two localities, obtained by adding up the individual samples CPO data in a common reference frame, show, however, a 'normal' upper mantle anisotropy with a maximum S-wave birrenfringence of ca. 5% at high angle to the both the maximum [010] and [100] axes concentrations, that is in the foliation, but normal to the lineation, and a minimum birefringence at low angle to the [100] maximum, that is parallel to the lineation.
ISSN: 0040-1951

hal-01053500
https://hal.archives-ouvertes.fr/hal-01053500
DOI : 10.1016/j.tecto.2014.02.017

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A new portable sampling system was developed to extract Radium isotopes from large volumes (up to 300 L) of fresh surface- and ground-waters of low Ra-activities (<5 mBq/L). Ra is quantitatively adsorbed on a small amount (6.5 g) of MnO2-coated acrylic fibers, which are then dried and burned at 600 °C in the laboratory. The resulting Mn-oxide powder (about 2 cm3 when compacted) is then analyzed through gamma-ray spectrometry which allows measurement of the whole Ra quartet (226Ra, 228Ra, 224Ra and 223Ra) in a single counting of a few days. The usual relative standard combined uncertainties (1σ) are 2–3% for 226Ra, 228Ra and 224Ra; and less than 10% for 223Ra. This method was applied to the analysis of Ra in karstic waters of the Lez aquifer, and surface- and ground-waters of the upper and middle Vidourle watershed (South of France). The analyzed waters have relatively low 226Ra activities (1–4 mBq/L) in both cases, regardless of the contrasted geology (Mesozoic limestone vs crystalline Variscan basement), but clearly distinct (228Ra/226Ra) ratios in agreement with the differences in Th/U ratios of the two drained areas. Short-lived Ra isotopes (224Ra and 223Ra) appear to be mainly influenced by near-surface desorption/recoil processes for most of the sampling sites.
ISSN: 0969-8043

hal-01491281
https://hal.archives-ouvertes.fr/hal-01491281
DOI : 10.1016/j.apradiso.2016.12.010

Éditeur(s) : HAL CCSD Wiley
Résumé : Wood specific gravity (WSG) is a strong predictor of tree performance across environmental gradients. Yet it remains unclear how anatomical elements linked to different wood functions contribute to variation in WSG in branches and roots across tropical forests. [br/][br/]We examined WSG and wood anatomy in white sand, clay terra firme and seasonally flooded forests in French Guiana, spanning broad environmental gradients found throughout Amazonia. We measured 15 traits relating to branches and small woody roots in 113 species representing the 15 most abundant species in each habitat and representative species from seven monophyletic lineages occurring in all habitats. [br/][br/]Fiber traits appear to be major determinants of WSG, independent of vessel traits, in branches and roots. Fiber traits and branch and root WSG increased from seasonally flooded species to clay terra firme species and lastly to white sand species. Branch and root wood traits were strongly phylogenetically constrained. Lineages differed in wood design, but exhibited similar variation in wood structure across habitats. [br/][br/]We conclude that tropical trees can invest differently in support and transport to respond to environmental conditions. Wind disturbance and drought stress represent significant filters driving tree distribution of Amazonian forests; hence we suggest that biophysical explanations should receive more attention.
ISSN: 0028-646X

hal-01195075
https://hal.archives-ouvertes.fr/hal-01195075
PRODINRA : 269680
PUBMED : 24329812

Résumé : L’incorporation de sous-produits agricoles ou de matériaux naturels dans la matrice cimentaire confère des propriétés intéressantes aux composites élaborés. L’objectif de cette thèse est d’élaborer un matériau pouvant répondre aux exigences mécaniques, thermiques et de durabilité des matériaux de construction en zone tropicale humide. Dans un premier temps, l’activité pouzzolanique d’une pouzzolane naturelle, de cendres de tronc de bambou et de cendres de bagasse de canne à sucre ont été évaluées. L’influence de leur incorporation a été ensuite étudiée sur les propriétés mécaniques et la durabilité des mortiers exposés à des ions chlorures et sulfates. Dans un second temps, l’influence de l’ajout de fibres de bagasse sur les propriétés thermiques et mécaniques des composites a été étudiée en fonction de différents paramètres (teneur en fibres, environnement de vieillissement, type de matrice cimentaire).Les résultats obtenus ont permis de montrer que les matériaux étudiés possèdent une activité pouzzolanique et qu’il est possible de les incorporer au ciment afin de lutter contre la corrosion. De plus, les composites élaborés avec des fibres de bagasse sont plus isolants que ceux élaborés sans fibres. Cependant, du point de vue des propriétés mécaniques, l’incorporation de fibres de bagasse diminue les contraintes à la flexion des composites.
The incorporation of crop wastes or natural materials in the cement matrix confers interesting properties to composites prepared. The aim of this thesis is to develop a material that can reach the mechanical, thermal and durability requirements for building materials in the humid tropical zone. Firstly, pozzolanic activity of a natural pozzolan, bamboo stem and sugar cane bagasse ashes has been determined. Influence of their incorporation on mechanical properties and durability of mortars exposed to chloride and sulphate ions was studied. Secondly, influence of addition of bagasse fibers on thermal and mechanical properties of composites was studied as a function of various parameters (fibers content, curing, type of cement matrix).These results has shown that the materials studied have pozzolanic activity and it is possible to incorporate them into the cement to fight against corrosion. Moreover, composites elaborated with bagasse fibers are more insulating than those elaborated without fibers. However, from the viewpoint of mechanical properties, incorporation of bagasse fibers decreases flexural strength of composites in the present work and under the conditions producing procedures that were adopted.

http://www.theses.fr/2014AGUY0804/document

Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers (IEEE)/Optical Society of America(OSA)
Résumé : International audience
Nanometric displacement measurements by Extrinsic Fiber Fabry-Perot interferometers (EFPI) is extremely susceptible to external environmental changes. Temperature, in particular, has a remarkable influence on the optical power and wavelength of the laser diode in use, in addition to the thermal expansion of the mechanical structure. In this paper we propose an optimization of the EFPI sensor in order to use it for very long-term (more than one year) and for high-precision displacement measurements. For this purpose, a real time and adaptive estimation procedure based on a homodyne technique and a Kalman filter is established. During a sinusoidal laser diode current modulation, the Kalman filter provides a correction of the amplitude drift caused by the resultant optical power modulation and external perturbations. Besides, stationary temperature transfer operators are estimated via experimental measurements to reduce the additive thermal noise induced in the optical phase and mechanical components.
ISSN: 0733-8724

hal-00876339
https://hal.archives-ouvertes.fr/hal-00876339
DOI : 10.1109/JLT.2012.2194476

Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers
Résumé : International audience
: A new set-up for exposure of human cells in vitro at 37°C to pulse-modulated 300 MHz and 500 MHz signals of future magnetic resonance imaging (MRI) systems is designed, built up, and characterized. Two dipole antennas, specifically designed for ultra high field MRI, are used as radiating structures. The electromagnetic (EM) field distribution inside the incubator containing the cells is computed, and it is shown to be in a good agreement with measurements. The electric field at the cell level is quantified numerically. Local, 1g average, and averaged over the culture medium volume SAR are provided along with the standard deviation values for each well. Temperature increments are measured inside the culture medium during the exposure using an optical fiber thermometer. Then we identify the pulse parameters corresponding to the thermal threshold of 1°C, usually considered as a threshold for thermally-induced biological effects. For these parameters, the induction of heat shock proteins is assessed to biologically verify a potential thermal response of cells. The data demonstrate that, under the considered experimental conditions, exposure to pulsemodulated radiations emulating typical ultra high field MRI signals, corresponding to temperature increments below 1°C, does not trigger any heat shock response in human brain cells.
ISSN: 0018-9294

hal-00874329
https://hal.archives-ouvertes.fr/hal-00874329
DOI : 10.1109/TBME.2013.2270371
PUBMED : 23799680

Éditeur(s) : HAL CCSD
Résumé : Couche G ou couche tertiaire : quel nom pour la couche interne des fibres du bois de tension ?. 11es Journées du Réseau Français des Parois
11es Journées du Réseau Français des Parois
Orléans, France

hal-01603178
https://hal.archives-ouvertes.fr/hal-01603178
PRODINRA : 398652

Résumé : Herbácea erecta o trepadora de hasta 1 m de alto, estolonífera y con tubérculos. Hojas imparipinnadas; folíolos ovados o elípticos, ápice agudo o acuminado, base obtusa. Panículas terminales con muchas flores; cáliz lobado hasta cerca de la mitad de su longitud, lóbulos lanceolados, acuminados; corola blanca, azul, rosada o purpúrea, levemente lobada. Baya (fruto) subglobosa, glabra, amarilla.
Herbacée dressée ou grimpante pouvant atteindre 1 m de haut; stolonifère à tubercules. Feuilles imparipennées; folioles ovés ou elliptiques, extrémité aiguë ou acuminée, base obtuse. Panicules terminales portant de nombreuses fleurs; calice lobé ayant approximativement la moitié de sa longueur, lobes lancéolés, acuminés; corolle blanche, bleue, rosée ou pourpre, légèrement lobée. Baie (fruit) subarrondie, glabre, jaune.
Herbaceous branched annual 0.3-1m high, with a mass of fine fiberous adventitious roots and swollen stem tubers.  Leaves pinnate with small interjected leaflets between the main pinnae; flowers white, red or purple; fruit a small inedible berry.
Oriunda del sur de América, ampliamente cultivada en todo el mundo.
Originaire du sud de l’;Amérique, cultivée dans le monde entier.
Native to South America, now widely cultivated worldwide.

http://www.tramil.net/fototeca/plant329

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : Mantle xenoliths in Pliocene alkali basalts of the eastern Betics (SE Iberia, Spain) are spinel ± plagioclase lherzolite, with minor harzburgite and wehrlite, displaying porphyroclastic or equigranular textures. Equigranular peridotites have olivine crystal preferred orientation (CPO) patterns similar to those of porphyroclastic xenoliths but slightly more dispersed. Olivine CPO shows [100]-fiber patterns characterized by strong alignment of [100]-axes subparallel to the stretching lineation and a girdle distribution of [010]-axes normal to it. This pattern is consistent with simple shear or transtensional deformation accommodated by dislocation creep. One xenolith provides evidence for synkinematic reactive percolation of subduction-related Si-rich melts/fluids that resulted in oriented crystallization of orthopyroxene. Despite a seemingly undeformed microstructure, the CPO in orthopyroxenite veins in composite xenoliths is identical to those of pyroxenes in the host peridotite, suggesting late-kinematic crystallization. Based on these observations, we propose that the annealing producing the equigranular microstructures was triggered by melt percolation in the shallow subcontinental lithospheric mantle coeval to the late Neogene formation of veins in composite xenoliths. Calculated seismic properties are characterized by fast propagation of P waves and polarization of fast S waves parallel to olivine [100]-axis (stretching lineation). These data are compatible with present-day seismic anisotropy observations in SE Iberia if the foliations in the lithospheric mantle are steeply dipping and lineations are subhorizontal with ENE strike, implying dominantly horizontal mantle flow in the ENE-WSW direction within vertical planes, that is, subparallel to the paleo-Iberian margin. The measured anisotropy could thus reflect a lithospheric fabric due to strike-slip deformation in the late Miocene in the context of WSW tearing of the subducted south Iberian margin lithosphere.
ISSN: 0278-7407

Droits : info:eu-repo/semantics/OpenAccess
hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809
https://hal.archives-ouvertes.fr/hal-01685809/document
https://hal.archives-ouvertes.fr/hal-01685809/file/Hidas_et_al-2016-Tectonics.pdf
DOI : 10.1002/2016TC004165

Éditeur(s) : HAL CCSD
Résumé : Monitoring crustal deformation during the interseismic phase when searching for earth transients requires precise instruments able to operate for very long periods. The ANR-LINES project aimed to develop three new instruments: a single-axis seismometer, a hydrostatic long base tiltmeter and a borehole pendulum tiltmeter. These three instruments benefit of an extrinsic Fabry-Pérot interferometer (EFFPI) with long optic fibers for displacement detections. Their mechanical architectures and their disposal of long fibers help these newly manufactured geophysical instruments complete their goals. The first objective of this study is to propose appropriate methods for estimating the phase of the optical path in the Fabry-Pérot cavities. A modulation of the laser diode current, followed by a homodyne demodulation of the interference signal and a Kalman filter, allow determining the phase in real time. The results are convincingwhile taking short periods measurements but require additional solutions for protection against environmental phenomena variations. The EFFPI sensor integrated in the LINES borehole tiltmeter gives it the opportunity to establish a differential measurement of the bob's oscillation thanks to three Fabry-Perot cavities. The LINES seismometer also uses the EFFPI displacement sensor to measure its coil's displacement. A description of the two instruments' mechanical structures and an analysis of the detected phenomena (slow movements, tides, earthquakes, microseisms . . . ) are part of this thesis.
Le suivi de la déformation de la croûte terrestre durant la phase intersismique pour la recherche des transitoires nécessite des instruments précis capables d'opérer pour de très longues durées. Le projet ANR-LINES a visé le développement de trois nouveaux instruments : un sismomètre mono-axial, un inclinomètre hydrostatique à longue base et un inclinomètre de forage pendulaire. Ces trois instruments profitent d'un capteur interférométrique de déplacement à longues fibres optiques du type Fabry-Pérot Extrinsèque (EFFPI). Leurs architectures mécaniques et l'utilisation de longues fibres permettent à ces instruments géophysiques nouvellement fabriqués d'atteindre les objectifs fixés. Le premier objectif de cette étude est de proposer des méthodes adaptées à l'estimation de la phase du chemin optique dans les cavités Fabry-Pérot. Une modulation du courant de la diode laser, suivie par une démodulation homodyne du signal d'interférence et un filtre de Kalman permettent de déterminer la phase en temps réel. Les résultats sont convaincants pour des mesures de courtes durées mais exigent des solutions complémentaires pour se prémunir des effets de la variation des phénomènes environnementaux. Le capteur EFFPI intégré dans l'inclinomètre de forage LINES lui offre l'opportunité d'établir une mesure différentielle de l'oscillation de la masselotte pendulée grâce à trois cavités Fabry-Pérot. Le sismomètre LINES utilise lui aussi le capteur de déplacement EFFPI pour la mesure du déplacement de sa bobine. Une description de l'architecture mécanique de ces instruments et une analyse des phénomènes détectés (mouvements lents, marées, séismes, microséismes . . . ) font partie de cette thèse.
https://tel.archives-ouvertes.fr/tel-00779335

tel-00779335
https://tel.archives-ouvertes.fr/tel-00779335
https://tel.archives-ouvertes.fr/tel-00779335/document
https://tel.archives-ouvertes.fr/tel-00779335/file/Manuscript_Chawah.pdf

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Due to shallow penetration of millimeter waves (MMW) and convection in liquid medium surrounding cells, the problem of accurate assessment of local MMW heating in in vitro experiments remains unsolved. Conventional dosimetric MMW techniques, such as infrared imaging or fiber optic (FO) sensors, face several inherent limits. Here we propose a methodology for accurate local temperature measurement and subsequent specific absorption rate (SAR) retrieval using microscale thermocouples (TC). SAR was retrieved by fitting the measured initial temperature rise to the numerical solution of an equivalent thermal model. It was found that the accuracy of temperature measurement depends on thermosensor size, that is, the smaller TC, the more accurate the temperature measurement. SAR determined using TC with lead diameters of 25 and 75m demonstrated 98.5% and 80.4% match with computed SAR, respectively. However, both TC provided the same temperature rises in long run (>10min). FO probe failed to measure adequately local heating both for short and long exposures due to the relatively large size of the probe sensor (400m) and time constant (0.6s). Calculated SAR in the cell monolayer was almost two times lower than that in the surrounding liquid. It was shown that the impact of the cell monolayer on heating due to its small thickness (5 to 10m) can be considered as negligible. Moreover, we demonstrated the possibility of accurate measurement of MMW-induced thermal pulses (up to 10 degrees C) using 25m TC. Bioelectromagnetics. 38:11-21, 2017. (c) 2016 Wiley Periodicals, Inc.
ISSN: 0197-8462

hal-01436768
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01436768
DOI : 10.1002/bem.21999
PUBMED : 27571392