Éditeur(s) : HAL CCSD
Résumé : International audience
A fiber interferometer interfaced to 3 geo-mechanical elements is presented for applications in geophysics. The fiber sensor is based on an extrinsic fiber Fabry-Perot interferometer (EFFPI) which incorporates a modulation scheme to lock the interferometer at quadrature and to enable displacement measurements below a quarter of the interrogating wavelength. It operates over a relatively large frequency dynamic of ~500000 with a precision better than 2 nm. The fiber interferometer is next interfaced to a differential hydrostatic long baseline inclinometer, a 3-axis borehole tiltmeter and a single-axis seismometer, respectively. Results obtained demonstrate that the fiber interferometrically-interrogated instruments exhibit performances equivalent to or even surpassing those of the reference instruments employed for comparison during their deployment to an underground test site since March 2012. Keywords—modulation-based extrinsic fiber Fabry-Perot interferometer; fiber optique hydrostatic inclinometer; fiber optique borehole tiltmeter; fiber optique seismometer
IEEE SENSORS 2015
Busan, South Korea

hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963/document
https://hal.archives-ouvertes.fr/hal-01265963/file/HCS3.pdf
DOI : 10.1109/ICSENS.2015.7370316

Éditeur(s) : IEEE
Résumé : It is now well understood that data on soil moisture and sea surface salinity (SSS) are required to improve meteorological and climate predictions. These two quantities are not yet available globally or with adequate temporal or spatial sampling. It is recognized that a spaceborne L-band radiometer with a suitable antenna is the most promising way of fulfilling this gap. With these scientific objectives and technical solution at the heart of a proposed mission concept the European Space Agency (ESA) selected the Soil Moisture and Ocean Salinity (SMOS) mission as its second Earth Explorer Opportunity Mission. The development of the SMOS mission was led by ESA in collaboration with the Centre National d'Etudes Spatiales (CNES) in France and the Centro para el Desarrollo Tecnologico Industrial (CDTI) in Spain. SMOS carries a single payload, an L-Band 2-D interferometric radiometer operating in the 1400-1427-MHz protected band [1]. The instrument receives the radiation emitted from Earth's surface, which can then be related to the moisture content in the first few centimeters of soil over land, and to salinity in the surface waters of the oceans. SMOS will achieve an unprecedented maximum spatial resolution of 50 km at L-band over land (43 km on average over the field of view), providing multiangular dual polarized (or fully polarized) brightness temperatures over the globe. SMOS has a revisit time of less than 3 days so as to retrieve soil moisture and ocean salinity data, meeting the mission's science objectives. The caveat in relation to its sampling requirements is that SMOS will have a somewhat reduced sensitivity when compared to conventional radiometers. The SMOS satellite was launched successfully on November 2, 2009.
Proceedings of the IEEE (0018-9219) (IEEE), 2010-05 , Vol. 98 , N. 5 , P. 666-687

Droits : 2010 IEEE – All Rights Reserved
http://archimer.ifremer.fr/doc/00004/11483/8065.pdf
DOI:10.1109/JPROC.2010.2043032
http://archimer.ifremer.fr/doc/00004/11483/

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Iran is an active continental domain accommodating the convergence between the Arabia and Eurasia plates. In northwestern Iran, deformation between the Central Iranian block and the Caucasus domain is mainly accommodated by right lateral strike-slip on the Tabriz fault. Cities and villages, including the city of Tabriz, have been destroyed by several strong historical earthquakes (M similar to 7). In this study, we compare the slip-rates estimated from geodetic measurements (radar interferometry and UPS) with those determined by dating a geomorphological offset of an alluvial fan along the Tabriz fault. The GPS measurements along two profiles normal to the Tabriz fault suggest a slip-rate of 7.3 +/- 1.3 mm yr(-1). The persistent scatterer radar interferometry analysis of Envisat satellite archives from 2003 to 2010 shows a velocity gradient (6 +/- 3 mm yr(-1)) across the Tabriz fault in agreement with GPS results. Moreover, it reveals that most of the area located south of the Tabriz fault is affected by subsidence, and that some sections of the fault probably act as barriers to fluid migration which may have an impact on its mechanical behaviour. West of Tabriz morphotectonic investigations on an alluvial fan surface show a right-lateral cumulative offset of 320 +/- 40 m Luminescence analyses of the coarse matrix alluvial fan deposits provide an age of 46 +/- 3 ka. This yields a slip-rate comprised between 6.5 and 7.3 mm yr(-1) along this segment. These results suggest that the Late Quaternary slip-rate is in agreement with the present-day slip-rate estimated by geodetic measurements, showing no slip-rate changes during the past 45 000 yr. Short-term variations within the 45 000 yr related to temporal earthquake clustering over few seismic cycles cannot be ruled out, but if they exist, they do not affect the geodetic and the geomorphological estimates. This study is in agreement with previous ones suggesting that long-term slip-rates (i.e. averaged over several tens of seismic cycles) are consistent with geodetic estimated slip-rates (i.e. extrapolated from few years of interseismic observations), and suggests that perturbations of fault slip-rates are related to variations over few seismic cycles.
ISSN: 0956-540X

hal-00844695
https://hal.archives-ouvertes.fr/hal-00844695
https://hal.archives-ouvertes.fr/hal-00844695v2/document
https://hal.archives-ouvertes.fr/hal-00844695/file/rizza2013.pdf
DOI : 10.1093/gji/ggt041

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Sensitive instruments like strainmeters and tiltmeters are necessary for measuring slowly varying low amplitude Earth deformations. Nonetheless, laser and fibre interferometers are particularly suitable for interrogating such instruments due to their extreme precision and accuracy. In this paper, a practical design of a simple pendulum borehole tiltmeter based on laser fibre interferometric displacement sensors is presented. A prototype instrument has been constructed using welded borosilicate with a pendulum length of 0.85 m resulting in a main resonance frequency of 0.6 Hz. By implementing three coplanar extrinsic fibre Fabry-Perot in-terferometric probes and appropriate signal filtering, our instrument provides tilt measurements that are insensitive to parasitic deformations caused by temperature and pressure variations. This prototype has been installed in an underground facility (Rustrel, France) where results show accurate measurements of Earth strains derived from Earth and ocean tides, local hydro-logic effects, as well as local and remote earthquakes. The large dynamic range and the high sensitivity of this tiltmeter render it an invaluable tool for numerous geophysical applications such as transient fault motion, volcanic strain and reservoir monitoring.
ISSN: 0956-540X

hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967/document
https://hal.archives-ouvertes.fr/hal-01265967/file/HCS1.pdf
DOI : 10.1093/gji/ggv358

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
P>The Strait of Hormuz area is a transition zone between the continental collision of the Zagros (west) and the subduction of an oceanic part of the Arabian Plate beneath the Makran wedge (east). Geology and recent GPS measurements indicate that about 15 mm yr-1 of relative motion in N10 degrees E direction is accommodated by two major fault systems: (1) the NNW-trending Minab-Zendan-Palami (MZP) fault system that connects the Main Zagros Thrust (MZT) to the inner Makran thrust system and the Frontal subduction thrust and (2) the N-trending Sabzevaran-Kahnuj-Jiroft (SKJ) fault system that bounds the Jazmurian depression to the west. We use dense GPS measurements along four transects across these fault systems in order to determine the strains spatial distribution. The northern GPS transect confirms the total fault slip rates for both fault systems estimated by the tectonic analyses (about 10 and 7.3 mm yr-1 in N10 degrees direction across the MZP and SKJ fault systems, respectively). For both fault systems, the elastic deformation spreads over shear zones that are several tens of kilometres wide. However, transects located close to latitude 27 degrees N reveal a much narrower shear zone (similar to 10 km) for the MZP fault system. Moreover, we confirm that most of the present-day strain is transferred towards the frontal subduction thrust rather than towards the inner Makran thrusts. In order to complement this new GPS velocity field with spatially dense measurements, we processed a set of ERS radar images by the radar interferometry (InSAR) technique. We used both a 'stacking' and a 'persistant-scatterers' approach to differentiate the ground deformation signal which spatial gradient is expected to be very low, from the atmospheric signal. Results from these interferograms appear to be relatively in agreement with the GPS-determined strain distribution. Nevertheless, they confirm the absence of any superficial creep behaviour since no sharp discontinuity on interferometric phase can be noted on any interferogram. Finally, we use a purely kinematic 'block model' inversion process to calculate slip rates and locking depths for each fault system from our GPS measurements. These models suggest that the relative quiescence over the last 200 yr has certainly produced a slip deficit as high as 2 m. So, we may wonder if the MZP fault system is not late in the interseismic phase of its earthquake cycle.
ISSN: 0956-540X

hal-00429386
https://hal.archives-ouvertes.fr/hal-00429386
DOI : 10.1111/j.1365-246X.2009.04321.x

Éditeur(s) : HAL CCSD Optical Society of America
Résumé : This Letter describes a dual-amplitude modulation technique incorporated into a double reflection extrinsic-type fiber Fabry-Perot interferometer to measure periodic, nonperiodic as well as quasi-static displacements. The modulation scheme simultaneously maintains the interference signal pair in quadrature and provides a reference signal for displacements inferior to a quarter of the source wavelength. The control and phase demodulation of the interferometer carried out via software enable quasi-real-time measurement and facilitates sensor alignment. The sensor system can be exploited in the low frequency range from 10−3 to ∼500 Hz and has a resolution better than 2.2 nm, targeting applications in geophysics.
ISSN: 0146-9592

hal-00758140
https://hal.archives-ouvertes.fr/hal-00758140
DOI : 10.1364/OL.37.002886

Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers (IEEE)/Optical Society of America(OSA)
Résumé : International audience
Nanometric displacement measurements by Extrinsic Fiber Fabry-Perot interferometers (EFPI) is extremely susceptible to external environmental changes. Temperature, in particular, has a remarkable influence on the optical power and wavelength of the laser diode in use, in addition to the thermal expansion of the mechanical structure. In this paper we propose an optimization of the EFPI sensor in order to use it for very long-term (more than one year) and for high-precision displacement measurements. For this purpose, a real time and adaptive estimation procedure based on a homodyne technique and a Kalman filter is established. During a sinusoidal laser diode current modulation, the Kalman filter provides a correction of the amplitude drift caused by the resultant optical power modulation and external perturbations. Besides, stationary temperature transfer operators are estimated via experimental measurements to reduce the additive thermal noise induced in the optical phase and mechanical components.
ISSN: 0733-8724

hal-00876339
https://hal.archives-ouvertes.fr/hal-00876339
DOI : 10.1109/JLT.2012.2194476

Éditeur(s) : HAL CCSD
Résumé : Monitoring crustal deformation during the interseismic phase when searching for earth transients requires precise instruments able to operate for very long periods. The ANR-LINES project aimed to develop three new instruments: a single-axis seismometer, a hydrostatic long base tiltmeter and a borehole pendulum tiltmeter. These three instruments benefit of an extrinsic Fabry-Pérot interferometer (EFFPI) with long optic fibers for displacement detections. Their mechanical architectures and their disposal of long fibers help these newly manufactured geophysical instruments complete their goals. The first objective of this study is to propose appropriate methods for estimating the phase of the optical path in the Fabry-Pérot cavities. A modulation of the laser diode current, followed by a homodyne demodulation of the interference signal and a Kalman filter, allow determining the phase in real time. The results are convincingwhile taking short periods measurements but require additional solutions for protection against environmental phenomena variations. The EFFPI sensor integrated in the LINES borehole tiltmeter gives it the opportunity to establish a differential measurement of the bob's oscillation thanks to three Fabry-Perot cavities. The LINES seismometer also uses the EFFPI displacement sensor to measure its coil's displacement. A description of the two instruments' mechanical structures and an analysis of the detected phenomena (slow movements, tides, earthquakes, microseisms . . . ) are part of this thesis.
Le suivi de la déformation de la croûte terrestre durant la phase intersismique pour la recherche des transitoires nécessite des instruments précis capables d'opérer pour de très longues durées. Le projet ANR-LINES a visé le développement de trois nouveaux instruments : un sismomètre mono-axial, un inclinomètre hydrostatique à longue base et un inclinomètre de forage pendulaire. Ces trois instruments profitent d'un capteur interférométrique de déplacement à longues fibres optiques du type Fabry-Pérot Extrinsèque (EFFPI). Leurs architectures mécaniques et l'utilisation de longues fibres permettent à ces instruments géophysiques nouvellement fabriqués d'atteindre les objectifs fixés. Le premier objectif de cette étude est de proposer des méthodes adaptées à l'estimation de la phase du chemin optique dans les cavités Fabry-Pérot. Une modulation du courant de la diode laser, suivie par une démodulation homodyne du signal d'interférence et un filtre de Kalman permettent de déterminer la phase en temps réel. Les résultats sont convaincants pour des mesures de courtes durées mais exigent des solutions complémentaires pour se prémunir des effets de la variation des phénomènes environnementaux. Le capteur EFFPI intégré dans l'inclinomètre de forage LINES lui offre l'opportunité d'établir une mesure différentielle de l'oscillation de la masselotte pendulée grâce à trois cavités Fabry-Pérot. Le sismomètre LINES utilise lui aussi le capteur de déplacement EFFPI pour la mesure du déplacement de sa bobine. Une description de l'architecture mécanique de ces instruments et une analyse des phénomènes détectés (mouvements lents, marées, séismes, microséismes . . . ) font partie de cette thèse.
https://tel.archives-ouvertes.fr/tel-00779335

tel-00779335
https://tel.archives-ouvertes.fr/tel-00779335
https://tel.archives-ouvertes.fr/tel-00779335/document
https://tel.archives-ouvertes.fr/tel-00779335/file/Manuscript_Chawah.pdf

Éditeur(s) : Ieee-inst Electrical Electronics Engineers Inc
Résumé : Analyzing the precision of vegetation height estimation with compact (i.e., single transmit instead of dual transmit) polarimetric interferometric synthetic aperture radar (PolInSAR) with the homogeneous random volume over ground model can help justify the use of this type of radar rather than using the full PolInSAR. However, since compact PolInSAR provides less information than full PolInSAR, a loss of precision in the vegetation height estimation is expected, which can depend on the single transmit polarization. The adaptation of the Cramer-Rao bound (CRB) derived for full PolInSAR in our earlier work to compact PolInSAR measurement provides a general methodology to characterize this loss of precision. Indeed, the CRB is a lower bound of the variance of unbiased estimators that does not depend on the choice of a particular estimation method. We illustrate this methodology for P-band measurements with three synthetic examples chosen for their variability of polarimetric responses. For these examples, it is shown that there can exist a large set of transmit polarizations for which the loss of precision described by the CRB is small (smaller than a factor 2) although there also exist transmit polarizations for which the loss can be large (about a factor 100). This loss of precision is compared with the large dependency of the precision to the vegetation height estimation that can be observed with the vegetation height (more than a factor 100 in the precision described by the CRB) when all the other parameters of the vegetation, ground, and radar system are constant.
Ieee Transactions On Geoscience And Remote Sensing (0196-2892) (Ieee-inst Electrical Electronics Engineers Inc), 2014-03 , Vol. 52 , N. 3 , P. 1879-1891

Droits : Copyright 2014 IEEE - All rights reserved.
http://archimer.ifremer.fr/doc/00174/28551/26968.pdf
DOI:10.1109/TGRS.2013.2256362
http://archimer.ifremer.fr/doc/00174/28551/

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The interpretation of coseismic surface deformation measurements through inversion techniques is of major importance to understand the mechanical behaviour of a seismic fault. Dense geodetic data sets in the vicinity of the ruptured fault provide unique constraints on detailed fault geometry and slip distribution at depth, making them complementary to seismological data. Bam earthquake (Mw 6.6, 2003 December 26) induced surface deformation has been precisely mapped by Envisat ASAR interferometry and by subpixel correlation techniques applied to Spot-5 and ASAR amplitude images. These oblique and horizontal estimations of deformation have been completed with one levelling profile along the main road crossing the rupture from west to east. We process these data (separately and jointly) in a two-step inversion technique, within the elastic half-space theory framework. Our objective is to determine the dislocation model at depth that satisfies simultaneously all the geodetic constraints. Also, we estimate the relative contribution of each geodetic data set to this inversion process.We first use a stochastic direct approach called neighbourhood algorithm in order to estimate the average characteristics of the rupture, and their relative uncertainty. Constraining in this way the geometry of the ruptured fault, we then linearize the inverse problem and compute the slip distribution on the fault using a standard weighted least-square technique, assuming the solution is smooth to some degree. At each step, we discuss the optimal models, their stability as well as the relative influence of each data set on the derived models parameters. Our preferred model reveals a shallow dislocation on a quasi-vertical fault, slightly dipping towards east. The slip vector has a strike-slip component as high as 2 m, while the dip-slip component seems negligible.However, the estimation of the resolution matrices emphasizes the fact that the details of deep fault slip distribution remain out of the scope of this ill-conditioned inverse problem. Yet, our preferred model suggests a main dislocation limited at depth between 1 and 6 km. By contrast, the aftershocks observed in the months following the earthquake are located just beneath the estimated main shock.
ISSN: 0956-540X

hal-00314173
https://hal.archives-ouvertes.fr/hal-00314173
https://hal.archives-ouvertes.fr/hal-00314173/document
https://hal.archives-ouvertes.fr/hal-00314173/file/GJI-2007-169-849-briole.pdf
DOI : 10.1111/j.1365-246X.2007.03358.x

Éditeur(s) : HAL CCSD
Résumé : The evolution of mountain belt piedmont is controlled by interactions between tectonics, erosion and sedimentation. To study coupling between these processes, we analyze morphometric data collected in the eastern Tian Shan piedmont (NW China) and develop a new analogue modelling technique. The modeling approach uses an experimental set-up and analog material specifically designed to study simultaneously tectonic structures (faults, folds), detailed morphology (drainage basins, channels, alluvial fans, etc.) and stratified sedimentation. Measurement techniques based on laser interferometry and image correlation are also developed to quantify the topographic and kinematic evolution of models.
Our experiments allow a new approach for the study of piedmont morphotectonic evolution. Our results indicate that tectonics mainly controls this evolution. The propagation of deformation and the formation of relief both significantly influence the development of drainage networks, the evolution of drainage basins and the formation of morphotectonic markers. Particularly, a study of alluvial fans and watershed metrics suggests that there is a dynamical equilibrium between uplift, erosion and morphology. In addition, our results show that terrace nucleation is controlled by thrust activity and hydrography adjustments. Folding of terraces responds to a homothetic deformation pattern.
This new methodology brings promising perspectives in the fields of geomorphology, seismotectonics and sedimentology.
L'évolution d'un piémont de chaîne de montagnes est contrôlée par les interactions entre la tectonique, l'érosion et la sédimentation. Pour étudier ces processus, nous avons analysé des données morphométriques issues des piémonts orientaux du Tian Shan (NW Chine) et développé un nouveau type de modélisation analogique. Cette approche utilise un dispositif et un matériau expérimental spécialement conçus pour modéliser simultanément des structures tectoniques (failles, plis), une morphologie détaillée (bassins versants, rivières, cônes alluviaux, etc.) et une sédimentation stratifiée. Des techniques de mesure optique ont été également mises en oeuvre afin de quantifier l'évolution topographique et cinématique des modèles.
Les expériences réalisées offrent une opportunité inédite d'étudier l'évolution morphotectonique d'un piémont. Nos résultats montrent que la tectonique exerce un contrôle de premier ordre sur cette évolution. La propagation de la déformation et la formation des reliefs influencent en effet significativement le développement du réseau de drainage, l'évolution des bassins versants et la formation des marqueurs morphotectoniques. En particulier, l'analyse de la morphométrie des cônes alluviaux et de leurs bassins versants suggère qu'un équilibre dynamique s'installe entre la surrection, l'érosion et la morphologie. Nos résultats montrent également que l'apparition des terrasses est guidée par l'activité des chevauchements et les adaptations de l'hydrographie. Leur modèle de plissement répond à une déformation homothétique.
Cette nouvelle approche ouvre des perspectives d'étude prometteuses en géomorphologie, sismotectonique et stratigraphie.
https://tel.archives-ouvertes.fr/tel-00339145

tel-00339145
https://tel.archives-ouvertes.fr/tel-00339145
https://tel.archives-ouvertes.fr/tel-00339145v2/document
https://tel.archives-ouvertes.fr/tel-00339145/file/These_Graveleau08.pdf

Éditeur(s) : IEEE
Résumé : Soil Moisture and Ocean Salinity, European Space Agency, is the first satellite mission addressing the challenge of measuring sea surface salinity from space. It uses an L-band microwave interferometric radiometer with aperture synthesis (MIRAS) that generates brightness temperature images, from which both geophysical variables are computed. The retrieval of salinity requires very demanding performances of the instrument in terms of calibration and stability. This paper highlights the importance of ocean salinity for the Earth's water cycle and climate; provides a detailed description of the MIRAS instrument, its principles of operation, calibration, and image-reconstruction techniques; and presents the algorithmic approach implemented for the retrieval of salinity from MIRAS observations, as well as the expected accuracy of the obtained results.
Proceedings of the IEEE (0018-9219) (IEEE), 2010-05 , Vol. 98 , N. 5 , P. 649-665

Droits : 2010 IEEE – All Rights Reserved
http://archimer.ifremer.fr/doc/00004/11482/8066.pdf
DOI:10.1109/JPROC.2009.2033096
http://archimer.ifremer.fr/doc/00004/11482/

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : We use InSAR to measure deformation and kinematics of the Mw = 4.9 Borujerd (2005/05/03) and Mw = 6.1 Chalan-Chulan (2006/03/31) earthquakes that occurred in the Zagros fold-and-thrust belt. The focal mechanism of the 2006 event is consistent with right lateral strike-slip motion and the event ruptured the Dorud-Borujerd segment of the Main Recent Fault. An Envisat interferogram spanning the 2006 event shows peak ground deformation of 9 cm in the satellite line-of-sight along a 10 km long fault portion. The interferogram spanning the 2005 earthquake is rather related to atmospheric artefact than to ground deformation. Dislocation models of the 2006 Chalan-Chulan event indicate dextral slip amounting to a maximum of 90 cm at a depth of 4 km. The predicted vertical displacements are in good agreement with differential levelling data. The 2006 event filled only a small part of the seismic gap located between large M = 7 events that occurred in 1909 and 1957.
ISSN: 0954-4879

hal-00411313
https://hal.archives-ouvertes.fr/hal-00411313
DOI : 10.1111/j.1365-3121.2008.00797.x

Éditeur(s) : HAL CCSD Berlin: A. Asher & Co.
Résumé : International audience
In this work, we compare IASI-retrieved vertical water vapour profiles and related precipitable water over a complex region, namely the Rhine Valley area, during the pre-operational period of IASI exploitation (June?August 2007). Both IASI water vapour mixing ratio profiles and integrated water vapour content are retrieved from L1C radiances spectra using two techniques and compared with water vapour related observations acquired during the Convective and Orographically-induced Precipitation Study (COPS) field campaign that took place in this area at that time (i.e. lidars, radiosoundings and a global positioning system - GPS - station network). This work addresses the issue of IASI vertical spatial resolution and its capability to detect two-layer water vapour structures such as those observed in a mountainous area and which play an important role in convective initiation or inhibition. We found that this capability mostly relies on the type of a-priori background vector (climatology or space-time colocated ECMWF analysis), which is used within the retrieval scheme. Systematic comparison of water vapour products derived from 71 IASI spectra confirms that IASI can retrieve water vapour amounts in 2 km width layers, in the lower troposphere, with an accuracy of approximately 10%.
ISSN: 0369-1845

hal-00923710
https://hal.archives-ouvertes.fr/hal-00923710
https://hal.archives-ouvertes.fr/hal-00923710/document
https://hal.archives-ouvertes.fr/hal-00923710/file/masiello.pdf
DOI : 10.1127/0941-2948/2013/0430

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
ISSN: 0956-540X

hal-00789114
https://hal.archives-ouvertes.fr/hal-00789114
DOI : 10.1093/gji/ggs085

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
In Taiwan, about one third of the lithospheric plate convergence between Eurasia and the Philippine Sea plate is accommodated on the eastern coast across the narrow Longitudinal Valley (LV). The Longitudinal Valley Fault (LVF) is the main seismically active fault zone in this region. However, the spatial distribution of ground deformation due to interseismic loading on locked fault segments remains widely unknown. To address this problem, we use a "permanent scatterer" (PS) interferometric synthetic aperture radar (InSAR) approach for processing the ERS satellite archives. The PS mean velocity maps allow accurately mapping and quantifying the ground deformation all along the LV. Assuming that, close to the surface, the fault plane along the central LVF creeping segment dips 55 degrees to the east, we derive a slip vector at the surface of similar to 25 mm/yr with a mean rake of 70 degrees. In agreement with our PS observations, shallow seismicity indicates a clear change in the fault mechanical behavior of the creeping segment around Fuli town. Finally, we propose a combination of the PS velocity fields for estimating a 3-D map of ground deformation. In the southern part of the LV, the vertical component reveals an uplift of the Coastal Range with respect to the LV of similar to 10 mm/yr. Moreover, between Taitung and Luyeh, the vertical deformation is essentially accommodated along the Luyeh Strand. Finally, north of Rueisuei, the Coastal Range uniformly subsides at similar to 15 mm/yr relative to the western side of the LV. However, a local uplift pattern is detected around latitude 23 degrees 42'.
ISSN: 0148-0227

hal-00595532
https://hal.archives-ouvertes.fr/hal-00595532
DOI : 10.1029/2010JB007898