Éditeur(s) : HAL CCSD
Résumé : This work focus on the characterization of the source and dynamic of compactional fluids during sedimentary burial, through two complementary examples of late orogenic oil‐field half‐grabens: The exhumed Lodève Permian Basin and a deep buried Jurassic basin in the North Viking Graben (North Sea).Constituting the main part of the thesis, a multi‐disciplinary approach was conducted in the Lodève Basin where Ba‐F‐Cu‐Pb polymetallic mineralized systems are trapped into synrift faults and paleokarsts in the carbonate basement at the hinge point of the rollover. The source, timing and P/T conditions of fluid migration were deduced from the analysis of the microfabric, the fluid inclusions microthermometry, and the isotopic (Sr, S, O, H) and Rare Earth Element (REE) signature. Results are then crossed with a structural and thermal modeling that consolidates the sequence and dynamics of fluid during burial.A similar approach was conducted in the North Viking Graben where fluid markers are restricted to 3D seismic and well core data. Comparable Ba‐Pb‐Zn veins are reported in basin margin, plugging one of the most important siliciclastic hydrocarbon reservoir in the substratum. This analysis provides additional constraints on basinal fluid behavior and allows us to propose a global dynamic model for various compositions of fluids and reservoirs.We conclude to a polyphase fluid sequence history including:(a) In the carbonate basement of the Lodève Basin, karstic paleocanyon incisions and associated cavities coupled to synrift fault, act as major drain for fluids. These structures are early affected by hypogen‐sulfuric karstification in response to the interaction between bacterial oxidation of sulfides entrapped within Lower Permian blackshales and the basement oxidizing aquifer.(b) Disequilibrium compaction initiates overpressure‐driven basinal fluid migration towards basin margins, characterized by temperatures around 150‐180°C and salinities between 9 et 18wt%eq.NaCl. Isotopic (Sr, S, O) and REE analyses reveal that Ba‐M+‐rich mineralizing fluids derived mainly from buried blackshales diagenesis. External fluids coming from the lower crust are also identified that play a key role in fluorite precipitation by the leaching of late hercynian granites (mean temperature of 250°C and salinity > 20wt%eq.NaCl).(c) During the synrift period, fluid overpressure is responsible for the periodic reactivation of fault plane according to seismic‐valve process, bedded‐control shearing and hydraulic brecciation at the basement‐seal interface. These mechanisms induce cyclic polymetallic mineralization by the mixing between in‐situ formation water and deep ascending basinal fluids.(d) Thermogenic fluids expulsion starts with last basinal fluids during late burial stage. Hydrocarbons thus migrate along the same regional pathways up to the rollover crest, where they are partly rerouted by the previous mineralized baffle.(e) In the Lodève basin, post‐rift exhumation of the margins led to the remobilization of synrift deposits by subaerial biochemical processes at the sulfate‐methane transition. The latter results from the interaction between the still active hydrocarbon dysmigration with a playa lake sulfate‐rich aquifer. Secondary low‐temperature barite fronts precipitate then within basement meteoric karsts.In addition to the « source to sink » model of basinal fluids, this work provides new insights on the early plugging of hydrocarbon reservoirs and for the metallogenesis of Mississippi Valley‐Type deposits.
Ce travail porte sur la caractérisation de la source et de la dynamique des fluides de bassin au cours de leur chargement à travers deux exemples complémentaires de demi‐grabens tardi‐orogéniques pétroliers : Le Bassin Permien de Lodève, aujourd’hui à l’affleurement et un bassin jurassique enfouis dans le North Viking Graben (Mer du Nord).Le coeur de la thèse concerne le Bassin de Lodève où, à partir d’une approche pluridisciplinaire intégrée, nous avons caractérisé l’architecture des minéralisations (Ba, F, Cu, Pb) piégées dans un réseau paléokarstique alimenté par les failles syn‐rift, dans le substratum carbonaté à l’apex du roll‐over. La source, le calendrier et les conditions de migration des fluides ont été approchés à partir de l’analyse de la micro‐fabrique, la microthermométrie sur inclusions fluides, les analyses isotopiques (Sr, S, O, H) et de Terres Rares. Les résultats analytiques ont été enfin croisés avec un modèle thermique et structural du bassin qui conforte la séquence et la dynamique du système fluide en cours d’enfouissement.Une démarche similaire, mais plus limitée, a été conduite dans le bassin du North Viking Graben où l’accès aux marqueurs fluides est restreint aux données de sismique 3D et de carottes. Comme à Lodève, les minéralisations Ba‐Pb‐Zn colmatent un réservoir dans le substratum à l’apex du roll‐over. Elles se présentent sous forme de ciments dans des grès ou des fractures. Cette analyse apporte des contraintes complémentaires et permet de proposer un modèle dynamique général avec des variantes en fonction de la nature des fluides et des réservoirs.On retiendra donc la séquence fluide suivante :(a) Dans le cas du bassin de Lodève sur substratum carbonaté, les chemins préférentiels de drainage se développent dans des paléocanyons N‐S couplés à un réseau de fractures et d’endokarsts météoriques. Ces derniers sont élargis en début de rifting par la dissolution hypogène sulfurique produite par l’oxydation bactérienne des sulfates et des pyrites des blackshales, au contact de l’aquifère oxydant du Cambrien.(b) Le déséquilibre de compaction initie la migration des fluides interstitiels en surpression vers les marges avec des températures autour de 150‐180°C et des salinités entre 9 et 18wt%eq.NaCl. Les analyses isotopiques (Sr, S, O) révèlent que la majorité des fluides provient de l’altération diagénétique des blackshales riches en métaux. Des interactions sont également mises en évidence avec des fluides profonds (entre 240°C et 260°C ; salinités > à 20wt%eq.NaCl), qui lessivent les granites tardi‐hercyniens.(c) Pendant le syn‐rift, les conditions de surpression de fluide permettent la réactivation cyclique des failles, les décollements stratigraphiques et la formation de brèches hydrauliques, favorisant la mise en connexion avec les réservoirs superficiels à l’apex du rollover. Le modèle de Sibson ajusté aux fluides de bassins est alors le moteur de la migration verticale.(d) Les fluides thermogéniques commencent à être expulsés avec les derniers fluides de compaction au cours d’un stade plus évolué de l’enfouissement en empruntant les mêmes chemins jusqu’à l’apex du roll over. Ils sont alors partiellement freinés et déviés par les colmatages minéralisés antérieurs.(e) A Lodève, la continentalisation des minéralisations antérieures au cours de l’exhumation post‐rift conduit à leur remaniement partiel au niveau de la transition sulfate‐méthane induite par l’interaction entre une playa évaporitique et la dysmigration des hydrocarbures. Des barytines secondaires de basse température, déprimées en Sr sont alors précipitées de manière synsédimentaire dans des karsts météoriques du socle.Outre l’illustration d’un modèle complet (source to sink) de dynamique des fluides dans un bassin, ce travail apporte de nouvelles contraintes dans l’approche du colmatage des réservoirs à hydrocarbures sur les têtes de blocs basculés et sur la genèse des gîtes miniers de type Mississippi Valley‐Type.
https://hal.archives-ouvertes.fr/tel-01457583

tel-01457583
https://hal.archives-ouvertes.fr/tel-01457583
https://hal.archives-ouvertes.fr/tel-01457583/document
https://hal.archives-ouvertes.fr/tel-01457583/file/th%C3%A8seLaurent2015V2.pdf

Éditeur(s) : HAL CCSD
Résumé : Volatile-rich, silica-undersaturated alkaline lavas record the important role of fluids during fluid-rock and magma-rock interactions in the mantle, which are key processes to understand the dynamics of the convective mantle and lithosphere-asthenosphere interactions in intracontinental settings. The aim of this thesis is to bring new constraints on the genesis of alkaline magmas by characterizing the crystallization conditions, the source and the partial melting processes taking part in the genesis of olivine nephelinites, pyroxene nephelinites and basanites from the Jbel Saghro volcanic field in the Moroccan Anti Atlas.The petrological and geochemical study of rocks and minerals coupled with the analysis of fluid inclusions constrains the pre-eruptive conditions of Saghro nephelinites to 1.7–2.2 GPa and ~1350 °C. Minerals show that nephelinitic magmas are rich in volatile elements (Cl, F, S), and fluid inclusions indicate that magmas were saturated with a CO2-rich fluid at pressures > 590 MPa. The various mineralogical assemblages and the presence of peridotite xenoliths suggest a rapid ascent for olivine nephelinites and more complex processes at depth for pyroxene nephelinites.Fractional crystallization and partial melting modelling of Saghro mafic lavas indicate that they are low-degree melts (0.6–2.5 %) of an amphibole-bearing carbonated peridotite enriched in incompatible elements, at the garnet-spinel transition (~80–85 km). Saghro nephelinites display a temporal evolution with a slight increase of the degree of melting and a decrease of the amount of residual amphibole from the oldest (olivine nephelinites, 9.6 Ma) to the most recent (pyroxene nephelinites, 2.9 Ma). Basanites form a system that is independent from nephelinites and are slightly higher-degree melts. Important variations in their chemical composition suggest variable amounts of fractional crystallization during ascent.The peculiar characteristics of Saghro nephelinites and basanites (enrichment in incompatible elements, negative anomalies in K, Zr, Hf and Ti, high Ca/Al and Zr/Hf ratios) indicate that their source was affected by carbonatitic metasomatism. The influence of this metasomatism is stronger for pyroxene nephelinites than for olivine nephelinites. These results suggest fluid-rock interactions beneath the Northwest African Craton, leading to the formation of a metasomatized mantle by CO2-rich carbonatitic components at the lithosphere-asthenosphere transition. The origin of the metasomatism inducing source enrichment and the formation of amphibole veins could be attributed to the melting of relict subducted oceanic lithosphere. The relatively low melting temperatures (< 1350 °C) suggest the absence of a thermal anomaly beneath the Jbel Saghro, and thus support a lithosphere delamination model as precursor of Saghro volca0,3nism. However, the increasing degree of partial melting over time, also observed in the Middle Atlas, together with the isotopic and geochemical similarities with Canary Islands alkaline lavas does not allow us to discard the influence of a deviation of the Canary mantle plume beneath northwest Africa.
Les laves alcalines sous-saturées riches en éléments volatils sont les marqueurs du rôle important des fluides dans le manteau et des interactions fluide-roche et magma-roche, processus clés pour comprendre la dynamique du manteau convectif et les interactions asthénosphère-lithosphère en domaine intracontinental. L’objectif de cette thèse est d’apporter de nouvelles contraintes sur la genèse des magmas alcalins en caractérisant les conditions de cristallisation, la source et les processus de fusion partielle à l’origine des néphélinites à olivine, des néphélinites à pyroxène et des basanites du champ volcanique du Jbel Saghro dans l’Anti-Atlas marocain.L’étude pétrologique et géochimique des roches et des minéraux, couplée à l’analyse des inclusions fluides a permis de contraindre les conditions pré-éruptives des néphélinites de Saghro à 1.7–2.2 GPa et ~1350 °C. Les minéraux montrent que les magmas néphélinitiques sont riches en éléments volatils (Cl, F, S), et les inclusions fluides indiquent que les magmas étaient saturés en fluide riche en CO2 à des pressions > 590 MPa. Les différents assemblages minéralogiques des néphélinites et la présence de xénolites péridotitiques suggèrent une ascension rapide des néphélinites à olivine et des processus plus complexes en profondeur pour les néphélinites à pyroxène.La modélisation des processus de cristallisation fractionnée et de fusion partielle des laves mafiques de Saghro a permis de déterminer qu’elles sont issues de faibles taux de fusion partielle (0.6–2.5 %) d’une péridotite carbonatée enrichie en éléments incompatibles, au niveau de la transition grenat–spinelle (~80–85 km) et en présence d’amphibole. Les néphélinites de Saghro montrent une évolution temporelle avec une légère augmentation du taux de fusion et une diminution de la quantité d’amphibole au résidu des plus anciennes (néphélinites à olivine, 9.6 Ma) aux plus récentes (néphélinites à pyroxène, 2.9 Ma). Les basanites forment un système indépendant des néphélinites et sont issues de taux de fusion plus élevés. Les fortes variations dans leur composition chimique suggèrent qu’elles ont subi de la cristallisation fractionnée lors de leur ascension.Les caractéristiques particulières des néphélinites et basanites de Saghro (enrichissement en éléments incompatibles, anomalies négatives en K, Zr, Hf et Ti, rapports Ca/Al et Zr/Hf élevés) indiquent que leur source a subi un métasomatisme principalement carbonatitique. L’influence de ce métasomatisme est plus forte pour les néphélinites à pyroxène que pour les néphélinites à olivine, impliquant une évolution temporelle de l’intensité du métasomatisme. Ces résultats suggèrent des interactions fluide-roche sous le craton Nord-Ouest Africain, entraînant la formation d'un manteau métasomatisé par des composants carbonatitiques riches en CO2 au niveau de la transition lithosphère-asthénosphère. L’origine du métasomatisme provoquant l’enrichissement de la source et la formation de veines d’amphibole pourrait être liée à la fusion de reliquats de croûte océanique subductée. Les températures de fusion relativement faibles (< 1350 °C) suggèrent l’absence d’anomalie thermique sous le Jbel Saghro, et favorisent donc un modèle de délamination de la lithosphère comme initiateur du volcanisme. Cependant, l’augmentation du taux de fusion partielle au cours du temps, également observée dans le Moyen Atlas, et les similitudes isotopiques et géochimiques avec les laves alcalines des îles Canaries ne permettent pas d’exclure une influence du panache des Canaries sur la source du volcanisme alcalin du Jbel Saghro.
https://tel.archives-ouvertes.fr/tel-01615888

NNT : 2015MONTS070
tel-01615888
https://tel.archives-ouvertes.fr/tel-01615888
https://tel.archives-ouvertes.fr/tel-01615888/document
https://tel.archives-ouvertes.fr/tel-01615888/file/53752_CHAMBOREDON_2015_archivage_cor.pdf

Éditeur(s) : HAL CCSD
Résumé : Geothermal energy is considered as a green and infinite energy source at human scale. Currently, the yield of geothermal power plants is limited to temperatures of the operating fluid which 350 °C. From tectonic and volcanic activity at mid-ocean ridges, Iceland is a location where supercritical fluid extraction (T> 375 °C) can considered for the near future. Exploiting such fluids could theoretically multiply by a factor of ten the electrical power delivered by geothermal wells. Can such fluids circulate at the base of brittle oceanic crust? This work investigates the petrophysical properties of basalts in order to constrain geophysical observations in Iceland and predict the behavior of very high temperature geo-hydrothermal reservoirs. The first approach consisted in studying the physical properties of rocks that have hosted deep hydrothermal circulations at oceanic ridges. The study of these rocks at ODP Site 1256 shows that the porosity measured both in the field and in the lab is associated with amphibolite facies alteration minerals (T> 500 ° C). The second approach was to recreate in the laboratory the conditions of pressure, temperature and pore fluid pressure of high temperature to supercritical hydrothermal systems to predict the mechanical and electrical properties of basalts under these conditions. The mechanical results indicate that the brittle/ductile transition occurs at a temperature of about 550° C, where a strong permeability decrease is expected. The implementation and calibration of a new cell for measuring electrical conductivity at high temperature provide the first results for the interpretation of geophysical data. When applied to basaltic crustal conditions in Iceland, these results indicate that hydrothermal fluids could circulate, at least temporarily, in a supercritical state up to 5 km depth.
La géothermie est considérée comme une source d'énergie propre et inépuisable à échelle humaine. Actuellement, le rendement des centrales géothermiques est limité à l'exploitation de fluides de températures inférieures à 350 °C. L'association de l'activité tectonique et volcanique aux dorsales océaniques fait de l'Islande un lieu où l'extraction de fluides supercritiques (T> 375 °C) peut être envisagée. Cette exploitation pourrait multiplier par dix la puissance électrique délivrée par le système géothermal. Ces fluides peuvent-ils circuler dans la croûte océanique ? Ce travail propose de contraindre les observations géophysiques et de prédire le fonctionnement des réservoirs géo-hydrothermaux de très haute température par l'étude des propriétés physiques des basaltes. La première approche est focalisée sur l'étude de roches ayant accueilli une circulation hydrothermale par le passé. L'étude de ces roches au site ODP 1256, montre que leur porosité est associée à la présence de minéraux d'altération hydrothermale du facies amphibolite (T> 500 °C). La seconde approche a consisté à recréer, en laboratoire, les conditions des systèmes hydrothermaux, à très haute température, afin de prédire les propriétés mécaniques et électriques des basaltes dans ces conditions. Les résultats mécaniques indiquent que la transition fragile/ductile, souvent associée à une forte décroissance de perméabilité, intervient à une température d'environ 550 °C. La mise en place d'une cellule de mesure de la conductivité électrique de haute température a fourni les premiers résultats utiles à l'analyse des données géophysiques. Appliqués aux conditions de la croûte basaltique Islandaise, ces résultats indiquent que des fluides hydrothermaux pourraient circuler au moins transitoirement à l'état supercritique jusqu'à ~ 5 km de profondeur.
https://tel.archives-ouvertes.fr/tel-00591798

tel-00591798
https://tel.archives-ouvertes.fr/tel-00591798
https://tel.archives-ouvertes.fr/tel-00591798/document
https://tel.archives-ouvertes.fr/tel-00591798/file/THESE_MV_pro.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In petroleum industry, the difference between pore pressure (Pp) and minimum horizontal stress Sh (termed the seal or retention capacity) is of major consideration because it is often assumed to represent how close a system is to hydraulic failure and thus the maximum hydrocarbon column height that can be maintained. While Sh and Pp are often considered to be independent parameters, several studies in the last decade have demonstrated that Sh and Pp are in fact coupled. However, the nature of this coupling relationship remains poorly understood. In this paper, we explore the influences of the spatial pore pressure distribution on Sh/Pp coupling and then on failure pressure predictions and trap integrity evaluation. With analytical models, we predict the fluid pressure sustainable within a reservoir before failure of its overpressured shale cover. We verify our analytical predictions with experiments involving analogue materials and fluids. We show that hydraulic fracturing and seal breach occur for fluid pressure greater than it would be expected from conventional retention capacity. This can be explained by the impact of the fluid overpressure field in the overburden and the pressure diffusion around the reservoir on the principal stresses. We calculate that supralithostatic pressure could locally be reached in overpressured covers. We also define the retention capacity of a cover (RC) surrounding a fluid source or reservoir as the difference between the failure pressure and the fluid overpressure prevailing in shale at the same depth. In response to a localized fluid pressure rise, we show that the retention capacity does not only depend on the pore fluid overpressure of the overburden but also on the tensile strength of the cover, its Poisson's ratio, and the depth and width of the fluid source.
ISSN: 0264-8172

hal-00590497
https://hal.archives-ouvertes.fr/hal-00590497
DOI : 10.1016/j.marpetgeo.2010.08.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
During compressive events, deformation in sedimentary basins is mainly accommodated by thrust faulting and related fold growth. Thrust faults are generally rooted in the basement and may act as conduits or barriers for crustal fluid flow. Most of recent studies suggest that fluid flow through such discontinuities is not apparent and depends on the structural levels of the thrust within the fold-and-thrust belt. In order to constrain the paleofluid flow through the Jaca thrust-sheet-top basin (Paleogene southwest-Pyrenean fold-and-thrust belt) this study compares on different thrust faults located at different structural levels. The microstructures in the different fault zones studied are similar and consist of pervasive cleavage, calcite shear veins (SV1), extension veins (EV1) and late dilatation veins (EV3). In order to constrain the nature and the source of fluids involved in fluid-rock interactions within fault zones, a geochemical approach, based on oxygen and carbon stable isotope and trace element compositions of calcite from different vein generations and host rocks was adopted. The results suggest a high complexity in the paleohydrological behaviors of thrust faults providing evidence for a fluid-flow compartmentalization within the basin. Previous studies in the southern part of the Axial Zone (North of the Jaca basin) indicates a circulation of deep metamorphic water, probably derived from the Paleozoic basement, along fault zones related to the major basement Gavarnie thrust. In contrast, in northern part of the Jaca basin, the Monte Perdido thrust fault is affected by a closed hydrological fluid system involving formation water during its activity. The Jaca and Cotiella thrust faults, in turn, both located more to the south in the basin, are characterized by a composite fluid flow system. Indeed, stable isotope and trace element compositions of the first generations of calcite veins suggest a relatively closed paleohydrological system, whereas the late calcite vein generations, which are probably associated with the late tectonic activity of the basin, support a contribution of both meteoric and marine waters. Based on these results, a schematic fluid-flow model is presented. This model allows visualization of three main fluid flow compartments along a N-S transect.
ISSN: 0264-8172

hal-00963606
https://hal.archives-ouvertes.fr/hal-00963606
DOI : 10.1016/j.marpetgeo.2013.09.005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study analyses the interactions between deformation and reactive fluid and melt percolation, and their effects on sub-arc mantle seismic properties based on microstructural observations on mantle xenoliths extracted by the Tubaf and Edison seamounts close to the Lihir Island, in the Papua New Guinea archipelago. These xenoliths sample an oceanic lithosphere, which has experienced high-temperature deformation in the presence of fluids or melts. This was followed by metasomatism under static conditions. Syn-kinematic percolation of reactive Si-rich melts or fluids in peridotites has produced pyroxene-enrichment, grain size reduction, and dispersion of olivine crystal preferred orientation (CPO). Fourier transform infrared spectroscopy analyses show that olivine has very low water contents (1-4 wt. ppm H2O), similar to spinel peridotites from other subduction zones. These low values may record both low water solubility in olivine at low pressure and dehydration during transport and exhumation. Water contents in pyroxenes are highly variable and likely result from spatially heterogeneous melt or fluid percolation. Analysis of olivine CPO indicates dominant activation of both (010)[100] and (001)[100] slip systems, which are characteristic of deformation under high temperature, low stress, low pressure and low to moderate hydrous conditions. Fast S-wave polarization and P- and Rayleigh propagation directions are thus parallel to the mantle flow direction. The pyroxene enrichment by melt-rock reactions is accompanied by dispersion of olivine CPO and induces a significant decrease of the maximum S-wave and P-wave anisotropy in the peridotites. The calculated seismic properties also show that the lowest Vp/Vs ratios (< 1.7) mapped in fore-arc mantle may only be explained by taking in consideration the CPO-induced elastic anisotropy of the peridotites.
ISSN: 0040-1951

hal-00950058
https://hal.archives-ouvertes.fr/hal-00950058
DOI : 10.1016/j.tecto.2013.09.024

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mantle above a subducting slab is the site of complex interactions between deformation, partial melting, fluid migration and magma transport. To constrain these interactions and their effects on olivine deformation, we analyze microstructures, crystal preferred orientations, and water contents of peridotite xenoliths entrained by andesites of the Avacha volcano, southern Kamchatka arc. These xenoliths are refractory spinel harzburgites that have coarse-grained microstructures with widely spaced subgrain boundaries and sinuous grain boundaries in olivine, consistent with deformation by dislocation creep under low deviatoric stress (< 13 MPa) and with a significant contribution from diffusional processes. Analysis of crystal preferred orientations (CPO) indicates dominant activation of high-temperature, low-stress {0kl}[100] slip systems in olivine and of(100)[001] in orthopyroxene. In most samples, coarse opx crystals, elongated parallel to the lineation, enclose small olivine grains in crystallographic continuity with neighbouring crystals, indicating crystallization of orthopyroxene at the expense of olivine as a result of reactive percolation of Si-rich fluids coeval with the high-temperature deformation. Secondary crystallization of interstitial orthopyroxene led locally to development of opx-rich lenses parallel to the foliation, characterized by a decrease in olivine grain size and dispersion of the olivine CPO without changing the dominant slip systems. Half of the samples also show acicular orthopyroxene aggregates with which is associated a fine-grained matrix composed of rounded strain-free olivine, orthopyroxene, spinel, and rare amphibole crystals. This matrix occurs pervasively along grain boundaries or forms millimeter-scale irregular lenses and anastomosing veinlets that crosscut the coarse crystals and their ductile deformation structures. Both acicular orthopyroxene and the fine-grained matrix are interpreted as resulting from reactive transport of H2O-rich fluids under static conditions, probably in the lithospheric mantle. Infrared analyses show that olivine contains 1-8 center dot 6 ppm by weight of water. These low water contents are similar to those observed in spinel peridotites from other subduction zones and probably record both the low solubility of water in olivine at low pressure and dehydration during exhumation of the xenoliths. Water contents in orthopyroxene are highly variable (25-506 ppm H2O), probably recording spatially heterogeneous interaction with fluids or melts and compositional disequilibrium in the studied samples. Change in the dominant percolation mechanism from porous flow to fracturing suggests cooling, consistent with the low temperatures estimated from pyroxene thermometry (< 800-900 degrees C). The Avacha xenoliths therefore record pervasive deformation of a region of the mantle under asthenospheric conditions, followed by its accretion to the base of the lithosphere, probably as a result of cooling of the mantle wedge. Percolation of Si-rich fluids or hydrous melts is recorded at all stages; this probably enhanced diffusion and lowered deviatoric stresses during ductile deformation, but did not change the dominant slip direction in olivine from [100] to [001].
ISSN: 0022-3530

hal-00456053
https://hal.archives-ouvertes.fr/hal-00456053
DOI : 10.1093/petrology/egp085

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The 40Ar/39Ar geochronological technique has significantly contributed to the study of crustal deformation. However, the frequent occurrence of extraneous argon in high-pressure terrains can make the interpretation of 40Ar/39Ar ages problematic. This contribution attempts to: i) characterize the distribution and origin of extraneous argon in the Cycladic Blueschist Unit (CBU, Greece) by applying the 40Ar/39Ar dating technique on three Cycladic islands, Syros, Tinos and Ios, which span a complete transect of the CBU and ii) discuss regional implications for the tectonometamorphic evolution of the CBU. Our results, combined with ages available in the literature, show that periods of peak-burial conditions (55–49 Ma) and syn- (45–38 Ma) to post-orogenic exhumation (37–21 Ma) are well constrained in the CBU by the 40Ar/39Ar method. Moreover, Variscan apparent ages are preserved in the Cycladic basement of Ios, indicating that the 40Ar/39Ar system was not completely reset during the Eocene metamorphic episode. Additionally, our 40Ar/39Ar data show that the occurrence of extraneous argon is heterogeneously distributed in the CBU. While high-pressure rocks of Syros and Tinos are only locally affected, extraneous argon is clearly evidenced in the CBU of Ios, yielding geologically meaningless ages up to 900 Ma. On each island, the most affected ages were obtained in microstructures where fluid circulation is enhanced such as shear bands or strain shadows around garnets. We suggest that the Cycladic Basement, a polymetamorphic continental unit, behaved as an argon reservoir that has been mobilized by fluid circulation at the Eocene. These argon-enriched fluids have then heterogeneously contaminated metamorphic rocks when percolating through the CBU. Finally, we claim that a minimum closure temperature of 550 °C must be accepted for the phengites of the CBU and conclude that volume diffusion is not the main process resetting the argon isotopic system in high-pressure rocks compare to recrystallization enhanced by fluid circulation and deformation.
ISSN: 0024-4937

Droits : http://creativecommons.org/licenses/by-nc-nd/
insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268/document
https://hal-insu.archives-ouvertes.fr/insu-01424268/file/Valentin-Lithos-Accepted-2016.pdf
DOI : 10.1016/j.lithos.2016.12.013

Éditeur(s) : HAL CCSD
Résumé : Sand intrusions (or injectites) are most often the product of post-depositional remobilization of sand leading to its injection into the surrounding rocks. While injectites were recognized for the first time nearly 200 years ago, their emplacement process has been studied for a couple of decades only, since the concepts of deep sea depositional environments have allowed us to better understand their emplacement processes. However, these processes are still relatively poorly understood. Our approach is based on the study of injectites in the Lower Congo Basin from seismic and well data, which we compare to a fossil system in the SE France basin. We have shown that: (1) In buried turbidite channel systems draping deposits on the channel flanks and terraces of channels have the same geophysical signature as 'wing-like' injectites. Finally, the only criterion for identifying seismic injectites is the presence of bedding-discordant seismic reflections, and in the best case the associated uplift of the overlying seismic reflectors. (2) Seismic-scale conical and saucer-shaped sand injectites have been identified in the Lower Congo Basin. The remobilization is likely due to overpressuring induced by the buoyancy effect of hydrocarbons trapped in the margins of a lobe buried underneath 160 m of sediment, followed by the sudden injection of fluidized sand associated with fault reactivation of faults (with a possible role of nearby salt diapirs). (3) A network of injectites (dykes, sills/wings and laccoliths) was formed in the Vocontian basin during the late Albian and/or early Cenomanian, from a lower-middle Albian turbidite channel. The emplacement is probably due to the early compartmentalization of the channel during its burial and the increase of the sedimentation rate generating overpressure; and the subsequent large influx of deep fluids triggering injection. The injection of sand was polyphased: a first episode formed the sills and another emplaced the dykes. Sills/wings and dykes propagated about 2 km laterally away from the parent sand body and about 200 m up to the surface, revealing a much more extended lateral than vertical reach, contrary to the classically accepted idea from the interpretation of seismic data. (4) The emplacement of this large network of injectites was governed by hydrofracturing. Therefore, its morphology is dependent on the host rock heterogeneity (isotropy, fractures), the paleo-stress orientation (ó3 = NW-SE) and the burial depth of the source (300-600 m) at the time of injection. The study of this fossil network allows us to define the relationship between morphology of the injected network and stress state at the time of injection. This relationship can be extrapolated to constrain the morphology of subsurface networks beyond seismicvisibility. (5) Sands injected into low permeability lithologies bear evidence to a major event of fluid escape in the studied basin, but also channeled fluids long after their formation. In this way, injectites both attest to specific episodes of fluid migration in sedimentary basins and contribute to long-lived re-routing of migrating fluids once emplaced. The injection of sand is associated with the sudden escape of fluids, probably resulting from a significant tectonic and/or sedimentary event; in addition, the architecture of injectite networks is governed by the local paleo-stress and heterogeneity in the host rock. Consequently, characterizing injectite networks is an important step in understanding the plumbing systems of continental margins, i.e. the post-depositional evolution of sedimentary basins.
Les intrusions sableuses (ou injectites) sont le plus souvent le produit de la remobilisation post-dépositionnelle des sédiments et de l'injection du sable dans les roches environnantes. Bien que reconnues pour la première fois il y a près de 200 ans, elles ne sont réellement étudiées que depuis quelques dizaines d'années, depuis que les concepts sur les environnements de dépôt dans les domaines marins profonds nous permettent de mieux comprendre les processus de mise en place. Cependant, ces processus restent encore aujourd'hui relativement mal compris. Notre approche repose sur l'étude d'injectites dans le bassin du Bas-Congo a partir de données de sismique et de puits que nous comparerons a un système fossile dans le bassin du SE de la France. Nous avons montre que : (1) Dans des systèmes de chenaux turbiditiques enfouis, les dépôts de drapage sur les marges et terrasses de chenaux présentent la même signature géophysique que les injectites de type "wing". Finalement, le seul critère sismique d'identification des injectites est la présence de réflexions sismiques sécantes vis-a-vis de la stratigraphie associée dans le meilleur des cas au soulèvement des réflecteurs sismiques sus-jacents. (2) Des injectites d'échelle sismique en forme de cône et d'assiette ont été identifiées dans le bassin du Bas-Congo. La remobilisation résulte probablement des pressions anormales induites par l'effet de flottabilité des hydrocarbures piégés dans les marges d'un lobe enfoui sous 160 m de sédiment, puis de l'injection soudaine du sable fluidise associée a la réactivation de failles (possible rôle des diapirs de sel a proximité). (3) Un réseau d'injectites (dykes, sills/wings et laccolites) s'est formé dans le bassin Vocontien entre la fin de l'Albien supérieur et/ou le début du Cénomanien, depuis un chenal turbiditique de l'Albien inférieur-moyen. La mise en place résulte probablement de la compartimentalisation précoce du chenal au cours de son enfouissement et de l'augmentation du taux de sédimentation générant la surpression et de l'apport ulterieur d'importante quantité de fluides profonds déclenchant l'injection. L'injection du sable a été polyphasée : une première injection a formé des sills et une suivante des dykes. Les sills/wings et les dykes se sont propagés latéralement au chenal source sur environ 2 km et vers la surface sur environ 200 m, mettant en évidence une forte remobilisation latérale plutôt que verticale, contrairement a l'idée classiquement admise a partir de l'interprétation des données sismiques. (4) La formation de ce large réseau d'injectites a été gouvernée par des mécanismes d'hydrofracturation. Par conséquent, sa morphologie a été dépendante des hétérogenéités de la roche hôte (milieu isotrope, fracture), des directions de paléo-contraintes (ƒÐ3 = NWSE) et de la profondeur d'enfouissement de la source (300-600 m) au moment de l'injection. L'étude de ce réseau fossile permet de définir les relations entre morphologie du réseau injecté et état de contraintes au moment de l'injection. Cette relation peut être extrapolée de façon à contraindre la morphologie des réseaux de subsurface au-delà de la visibilité sismique. (5) Les sables injectés dans des lithologies de faible perméabilité témoignent d'un épisode d'échappement de fluide important dans les bassins étudiés mais ont aussi guide les fluides longtemps après leur formation. Les injectites contribuent ainsi a l'initiation épisodique et la pérennisation de migrations de fluides dans les bassins sedimentaires. Le processus d'injection est associé a l'échappement brutal de fluides, résultant vraisemblablement d'un évènement tectonique et/ou sédimentaire important, et l'architecture des réseaux d'injectites est gouverné par les paléo-contraintes locales et les hétérogénéités de la roche hôte. Par conséquent, la caractérisation des réseaux d'injectites est une étape importante dans la compréhension de la plomberie des marges, c'est-a-dire l'évolution post-dépôt des bassins sédimentaires.
https://tel.archives-ouvertes.fr/tel-01011486

tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486/document
https://tel.archives-ouvertes.fr/tel-01011486/file/These_Monnier_2013_banalisee.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Serpentinites form by hydration of mantle peridotite and constitute the largest potential reservoir of fluid-mobile elements entering subduction zones. Isotope ratios of one such element, boron, distinguish fluid contributions from crustal versus serpentinite sources. Despite 85% of boron hosted within abyssal peridotite being lost at the onset of subduction at the lizardite-to-antigorite transition, a sufficient cargo of boron to account for the composition of island arc magma is retained (c. 7 μg g− 1, with a δ11B of + 22‰) until the down-going slab reaches the antigorite-out isograd. At this point a 11B-rich fluid, capable of providing the distinctive δ11B signature of island arc basalts, is released. Beyond the uniquely preserved antigorite-out isograd in serpentinites from Cerro del Almirez, Betic Cordillera, Spain, the prograde lithologies (antigorite–chlorite–orthopyroxene–olivine serpentinite, granofels-texture chlorite-harzburgite and spinifex-texture chlorite-harzburgite) have very different boron isotope signatures (δ11B = − 3 to + 6‰), but with no significant difference in boron concentration compared to the antigorite-serpentinite on the low P–T side of the isograd. 11B-rich fluid, which at least partly equilibrated with pelagic sediments, is implicated in the composition of these prograde lithologies, which dehydrated under open-system conditions. Serpentinite-hosted boron lost during the early stages of dehydration is readily incorporated into forearc peridotite. This, in turn, may be dragged to sub-arc depths as a result of subduction erosion and incorporated in a mélange comprising forearc serpentinite, altered oceanic crust and pelagic sediment. At the antigorite-out isograd it dehydrates, thus potentially providing an additional source of 11B-rich fluids.
ISSN: 0009-2541

hal-01172276
https://hal.archives-ouvertes.fr/hal-01172276
DOI : 10.1016/j.chemgeo.2014.03.015

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We provide new insights into the geochemistry of serpentinites from the Alpine orogenic wedge representing a paleo-subduction zone. These serpentinites are derived from similar oceanic protoliths, but they have experienced different metamorphic conditions related to three different structural levels of the paleo-subduction zone ((1) obducted: Chenaillet ophiolite, (2) accretionary wedge: Queyras Schistes lustrés complex and (3) serpentinite channel: Monviso ophiolite). Metamorphism undergone by these three units is well defined, increasing eastward from sub-greenschist to eclogite facies conditions, and allows us to examine trace element behavior from the oceanic ridge environment to subduction. Serpentinites first record moderate trace element enrichment due to seawater interaction resulting in the replacement of olivine and pyroxene by chrysotile and lizardite below 300 °C. In the sediment-dominated accretionary wedge, serpentinites are strongly enriched in fluid-mobile-elements (B, Li, As, Sb, and Cs) and act as a trapping system following the metamorphic gradient (from 300 to 390 °C) up to total replacement of the lizardite/chrysotile assemblage by antigorite. Under higher temperature conditions (T > 390 °C), no enrichment was observed, and some fluid-mobile elements were released (B, Li, Cs, and Sr). Moreover, in the serpentinite channel (T > 460 °C), most of the fluid-mobile elements are absent due to the scarcity of metasediments which prevent geochemical exchange between metasediments and serpentinites. This is also due to the onset of antigorite breakdown and the release of fluid-mobile elements. Thus, we emphasize that the geochemistry of Alpine serpentinites is strongly dependent on (1) the grade of metamorphism and (2) the ability of metasediments to supply fluid-mobile elements. We conclude that serpentinites act as a trap-and-release system for fluid-mobile elements in a subduction context.
ISSN: 0009-2541

hal-00996839
https://hal.archives-ouvertes.fr/hal-00996839
DOI : 10.1016/j.chemgeo.2013.02.008

Éditeur(s) : HAL CCSD
Résumé : This work provides new constraints on the interactions between deformation and percolation of melt or fluids, as well as on the implications of these processes for the seismic properties of the mantle wedge. It is based on the analysis of spinel peridotites from the massif of Ronda (Spain) and two xenolith suites from active subduction zones (Kamchatka, Papua New Guinea). A coupled structural, petrological and geochemical study of these samples shows that they underwent a reactive percolation of melts or Si-rich fluids, which was synchronous to a deformation event occurring under high temperature and low stress conditions, consistent with the PT conditions at the base of the lithosphere or in the asthenosphere. This reactive percolation is responsible for enrichment in pyroxenes, mainly orthopyroxene, which is often localized in bands parallel to the high-temperature foliation. This enrichment is associated with grain size reduction and dispersion of the crystallographic orientation of olivine. The dominant slip system in olivine is {0kl}[100], which results in fast S-wave polarization parallel to the flow direction in the mantle. The decrease in the intensity of the olivine crystal preferred orientations associated with the enrichment in pyroxene results in significant decrease of the anisotropy that may induce an underestimation of the thickness of the anisotropic layer by up to 33%. The observed orthopyroxene enrichment also lowers the Vp/Vs ratio, but cannot explain Vp/Vs < 1.7 mapped locally in the fore-arc mantle in Japan and the Andes. Such low Vp/Vs ratios may however be explained by considering the intrinsic anisotropy of the peridotites, which is generally ignored in large-scale Vp/Vs ratio mapping of the mantle wedge. Infrared analyses show that olivine from the both xenolith collections contains less water than the theoretical saturation calculated for their estimated equilibrium temperature in the spinel stability field. These low water content are similar to those observed in spinel peridotites from other subduction zones and probably record both the low solubility of water in olivine at relatively low pressure and dehydration during exhumation of the xenoliths. These measured water contents as well as theoretical saturation estimations are not sufficient to change the dominant slip direction of in olivine from [100] to [001].
Ce travail apporte de nouvelles contraintes sur les interactions entre déformation et processus d'hydratation et de percolation de magma ou de fluides dans le manteau à l'aplomb d'une zone de subduction et leurs implications sur les propriétés sismiques dans le coin mantellique. Il se base sur l'analyse de péridotites à spinelle provenant du massif de Ronda (Espagne) et deux séries de xénolites issues de zones de subduction actives (Kamchatka, Papouasie-Nouvelle-Guinée). L'étude structurale, pétrologique et géochimique de ces échantillons montrent qu'ils ont subit une percolation réactive de magma ou de fluide synchrone d'une déformation de haute température basse contrainte cohérente avec les condition PT de la base de la lithosphère ou de l'asthénosphère. Cette percolation réactive est responsable d'un enrichissement en pyroxènes, qui est souvent localisé dans des bandes parallèles à la foliation. Cet enrichissement est associé à une dispersion de l'orientation cristallographique de l'olivine. Les systèmes de glissement dominant dans l'olivine sont dans tous les cas {0kl}[100], ce qui implique que la direction de polarisation rapide des ondes S dans la partie supérieure du coin mantellique est parallèle à la direction d'écoulement dans le manteau. La décroissance de l'intensité des OPR de l'olivine associée à l'enrichissement en pyroxènes a pour conséquence une réduction non négligeable de l'anisotropie sismique qui peut induire jusqu'à 33% d'erreur sur l'interprétation de l'épaisseur de la couche anisotrope. Un enrichissement en orthopyroxène peut aussi entraîner une baisse du rapport Vp/Vs, mais ne peut expliquer les rapports Vp/Vs <1,7 cartés dans certains avant-arcs. Cependant de telles valeurs peuvent être expliquées si l'anisotropie des péridotites du coin mantellique est prise en compte. Les analyses par spectroscopie infra-rouge montrent que les olivines des deux séries de xénolites étudiées contiennent moins d'eau que la saturation théorique calculée pour leurs températures d'équilibre dans le domaine du spinelle. Ces faibles concentrations en eau sont similaires à celles observées dans les olivines des péridotites à spinelle des autres zones de subduction. Elles enregistrent probablement la faible solubilité de l'eau dans l'olivine à des pressions relativement basses et la déshydratation au cours de l'exhumation des xénolites. Ces teneurs en eau mesurées ainsi que les estimations de la saturation théorique ne sont pas suffisantes pour changer la direction de glissement dominante dans l'olivine de [100] à [001].
https://tel.archives-ouvertes.fr/tel-00689832

tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832/document
https://tel.archives-ouvertes.fr/tel-00689832/file/These-Soustelle2010.pdf

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Direct numerical simulations of flow through two millimeter-scale rock samples of limestone and sandstone are performed using three diverse fluid dynamic simulators. The resulting steady-state velocity fields are compared in terms of the associated empirical probability density functions (PDFs) and key statistics of the velocity fields. The pore space geometry of each sample is imaged at 5.06−μm voxel size resolution using X-ray microtomography. The samples offer contrasting characteristics in terms of total connected porosity (about 0.31 for the limestone and 0.07 for the sandstone) and are typical of several applications in hydrogeology and petroleum engineering. The three-dimensional fluid velocity fields within the explicit pore spaces are simulated using ANSYS® FLUENT® ANSYS Inc. (2009), EULAG Prusa et al. (Comput. Fluids 37, 1193–1207 2008), and SSTOKES Sarkar et al. (2002). These computational approaches are highly disperse in terms of algorithmic complexity, differ in terms of their governing equations, the adopted numerical methodologies, the enforcement of internal no-slip boundary conditions at the fluid-solid interface, and the computational mesh structure. As metrics of comparison to probe in a statistical sense the internal similarities/differences across sample populations of velocities obtained through the computational systems, we consider (i) integral quantities, such as the Darcy flux and (ii) main statistical moments of local velocity distributions including local correlations between velocity fields. Comparison of simulation results indicates that mutually consistent estimates of the state of flow are obtained in the analyzed samples of natural pore spaces despite the considerable differences associated with the three computational approaches. We note that in the higher porosity limestone sample, the structures of the velocity fields obtained using ANSYS FLUENT and EULAG are more alike than either compared against the results obtained using SSTOKES. In the low-porosity sample, the structures of the velocity fields obtained by EULAG and SSTOKES are more similar than either is to the fields obtained using ANSYS FLUENT. With respect to macroscopic quantities, ANSYS FLUENT and SSTOKES provide similar results in terms of the average vertical velocity for both of the complex microscale geometries considered, while EULAG tends to render the largest velocity values. The influence of the pore space structure on fluid velocity field characteristics is also discussed.
ISSN: 1420-0597

hal-01174152
https://hal.archives-ouvertes.fr/hal-01174152
DOI : 10.1007/s10596-015-9486-7

Éditeur(s) : HAL CCSD
Résumé : International audience
In orogens, shortening is mainly accommodated by thrusts, which constitute preferential zones for fluid–rock interactions. Fluid flow, mass transfer, and mineralogical reactions taking place along thrusts have been intensely investigated, especially in sedimentary basins for petroleum and uranium research. This study combines petrological investigations, mineralogical quantifications, and geochemical characterizations with a wide range of analytical tools with the aim of defining the fluid properties (nature, origin, temperature, and redox) and fluid–host rock interactions (mass transfers, recrystallization mechanisms, and newly formed synkinematic mineralization) in the Pic-de-Port-Vieux thrust fault zone (Pyrenees, Spain). We demonstrate that two geochemically contrasted rocks have been transformed by fluid flow under low-grade metamorphism conditions during thrusting. The hanging-wall Triassic red pelite was locally bleached, while the footwall Cretaceous dolomitic limestone was mylonitized. The results suggest that thrusting was accompanied by a dynamic calcite recrystallization in the dolomitic limestone as well as by leaching of iron via destabilization of iron oxides and phyllosilicate crystallization in the pelite. Geochemical and physical changes highlighted in this study have strong implications on the understanding of the thrust behavior (tectonic and hydraulic), and improve our knowledge of fluid–rock interactions in open fluid systems in the crust.
Contributions to Mineralogy and Petrology

hal-01575548
https://hal-univ-fcomte.archives-ouvertes.fr/hal-01575548
DOI : 10.1007/s00410-017-1394-5

Éditeur(s) : HAL CCSD Elsevier
Résumé : A synthesis of backscatter imagery coupled with a large 3D seismic dataset in the Lower Congo Basin (LCB) reveals a patchy distribution of features interpreted to be associated with fluid seepage from 300 m to 2500 m water depth. With the exception of one region of anomalous backscatter positive-relief mounds, all inferred seep sites occur in negative-relief pockmarks. The extensive 3D seismic dataset in the LCB offers a unique opportunity to study the plumbing system that is feeding surface cold seep systems, and in general, to reconstruct the relationship between tectonics and fluid flow in continental margins. The fluid seeps in the LCB are associated with morphologically, stratigraphically or tectonically controlled focused fluid flow. The integration of the geophysical datasets, backscatter imagery coupled to 3D seismic, clearly indicates that fluid seeps are not randomly distributed, but their seabed organization reflects 1) the location of the underlying structure (reservoir or trap) where the fluids are coming from, 2) the geometry and morphology of the reservoir/trap, and 3) the discontinuities in the sedimentary column along which fluids have migrated. In the LCB seafloor pockmarks are always associated with underlying tectonic structures (fault zones, salt diapirs, polygonal faults) or buried sedimentary bodies (turbiditic channels, erosional surfaces), whereas they never occur above sub-horizontal parallel-stratified fine-grained sediments. Even if triggering processes can not be clearly defined here, we propose a model of seafloor fluid seep organization, which represents a new tool for identifying the geometry of flow pathways and the underlying buried bodies where the fluids are originating from. This qualitative 3D model provides insight into the geohydrologic processes of continental margins.
ISSN: 0025-3227

hal-00406640
https://hal.archives-ouvertes.fr/hal-00406640
DOI : 10.1016/j.margeo.2007.06.003

Éditeur(s) : HAL CCSD Mineralogical Society of America
Résumé : International audience
Accessory phases are important hosts of trace elements; allanite may contain >90% of the REE in a bulk rock. The mobility and redistribution of several trace elements, notably HREE, Th, U, and Y is thus controlled by reactions involving allanite and other REE phases, as well as several rock-forming minerals. As these elements are commonly concentrated in mature elastic sediments, a suite of impure quartzite was studied. Two eclogite facies samples from the Monometamorphic Cover Complex of the Sesia Zone (Western Italian Alps) are presented in some detail, as they reveal a remarkably rich spectrum of reaction relationships that involve REE phases.;Two allanite-forming reactions were inferred from textures and phase compositions;(1) monazite + Ca-silicate(?) + fluid -> allanite + apatite + thorite;;(2) monazite + thorite + Ca-silicate(?) + fluid -> Th-rich allanite + auerlite +/- apatite.;Petrographic observations and thermodynamic models suggest that allanite entered the HP assemblage at similar to 530 degrees C and 17-18 kbar during prograde metamorphism.;In one sample, allanite is rimmed by epidote rich in Y and HREE that grew at the expense of xenotime. Two net transfer reactions were derived;(3) xenotime + allanite + fluid -> Y-rich epidote + apatite + thorite;;(4) xenotime + allanite + fluid -> Y-rich epidote + aeschynite + thorite + (phosphate?).;Textural relationships and trace element analyses of coexisting allanite/monazite and xenotime/Y-rich epidote reveal systematic partitioning of the REE. Partition coefficients for the HREE are compatible with equilibrium fractionation, whereas those for the LREE show patterns that seem to be inherited from the precursor phases, in this case zircon with variable LREE composition.
ISSN: 0003-004X

hal-00745674
https://hal.archives-ouvertes.fr/hal-00745674
DOI : 10.2138/am.2012.3832

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Transport of liquid and gaseous hydrocarbons through focused fluid flow systems is a widespread process in continental margins and sedimentary basins, which is gaining increased attention in the assessment of geohazards, environment conservation, and securing fossil energy resources. Studying the abundance, distribution and drivers for this process is crucial for understanding its role in 1) the dynamics of gas hydrate accumulation and destabilization, 2) submarine slope stability and related tsunamis, 3) the plethora of chemosynthetic benthic ecosystems that develop in deep seep sites, and 4) the input of greenhouse gases (e.g. methane) into the ocean/atmosphere system, which may influence the atmospheric carbon budget and Earth's paleo- and present climate. New ocean exploration tools provide ever more data and improve our understanding of these systems. However, the subject still suffers from a lack of interdisciplinary knowledge dissemination. The ongoing international debate about the timing and the processes that control fluid expulsion in sedimentary basins is fuelled by their implications for structural and petroleum geology. Because fluids expelled at cold seeps originate at depth they represent open windows into the underlying petroleum systems and are valuable indicators for the reservoir systems. They may also help in deciphering past and predicting future climate change because worldwide release of large amounts of fluids may have an impact on the chemistry of the ocean and atmosphere.
ISSN: 0025-3227

hal-00772472
https://hal.archives-ouvertes.fr/hal-00772472
DOI : 10.1016/j.margeo.2012.10.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In orogenic systems, thrust faults play a major role in stacking different tectonic units and may act as conduits for the expulsion of large amounts of fluid of different origins (metamorphic, diagenetic, meteoric). This study focuses on the Monte Perdido thrust unit emplaced in the Paleogene Jaca thrust-sheet-top basin, in the SW-central Pyrenees. We aim to decipher the mechanisms and P-T conditions of deformation in fault zones and characterize the related fluid involvement, through combined microstructural, geochemical and microthermometry analyses. Two thrust faults cutting platform limestones, marls and siliciclastic turbidites of the lower part of the basin-fill (Paleocene-lower Eocene) have been studied. The fault zones are characterized by metre-thick shear zones with highly deformed, foliated clay-rich sediments. Foliation is underlined by preferentially oriented phyllosilicates. Several generations of shear and extension calcite, quartz and chlorite-bearing veins attest to fluid-rock interactions during a multi-stage deformation. Microstructural observations and stable isotope analyses on calcite from veins and host sediments suggest that deformation was aseismic and dominated by diffusive mass transfer from pressure solution sites along cleavage and stylolites to the precipitation sites in veins, with mineralizing fluids in equilibrium with the host sediments. Our results suggest an essentially closed hydrologic system, and imply the absence of significant fluid flow along the studied fault zones. Microthermometric study on fluid inclusions present in calcite and quartz veins, and calcite-quartz oxygen isotopic fractionation determined for the first generation shear veins, allow a geothermal gradient of 34 degrees C/km to be estimated. Analytical results demonstrate an evolution of the fault zones in three stages. The first stage was related to the emplacement of the Monte Perdido thrust unit during the middle Eocene at a temperature of similar to 208 degrees C and a burial depth of similar to 5.7 km. The second stage corresponds to a fault reactivation at a temperature of similar to 240 degrees C and a burial depth of similar to 6.5 km. The latter deformation may have been related to folding of the Monte Perdido thrust unit during the emplacement of the underlying Gavarnie thrust unit during the late Eocene-early Oligocene, with deeper burial resulting from aggradation of the thrust-sheet-top basin-fill. The last event corresponds to the formation of a dilatant vein system likely related to the exhumation of the massif.
ISSN: 0191-8141

hal-00644828
https://hal.archives-ouvertes.fr/hal-00644828
DOI : 10.1016/j.jsg.2011.06.006

Éditeur(s) : HAL CCSD Society of Exploration Geophysicists
Résumé : low frequency seismic attenuation
International audience
The study of wave attenuation in partially saturated porous rocks over a broad frequency range provides valuable information about the fluid system of reservoirs, which are inherently multiple phase fluid system. Until now, not much laboratory data have been collected in the seismically relevant low frequency range and existing literature data on partially saturated rock are very limited. The main goal of our work is to experimentally measure the bulk seismic attenuation on fluid-bearing rocks, using natural rock samples in an efficient way at in situ conditions. We are currently fine-tuning our attenuation measurement prototype. Preliminary bench-top results are promising and show consistency with reported experimental data with dry, partially and fully fluid saturated rocks. Measurements with the machine are accurate and precise.
ISSN: 1052-3812

hal-00564863
https://hal.archives-ouvertes.fr/hal-00564863
DOI : 10.1190/1.3513397

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : Society's needs for a network of in situ ocean observing systems cross many areas of earth and marine science. Here we review the science themes that benefit from data supplied from ocean observatories. Understanding from existing studies is fragmented to the extent that it lacks the coherent long-term monitoring needed to address questions at the scales essential to understand climate change and improve geo-hazard early warning. Data sets from the deep sea are particularly rare with long-term data available from only a few locations worldwide. These science areas have impacts on societal health and well-being and our awareness of ocean function in a shifting climate. Substantial efforts are underway to realise a network of open-ocean observatories around European Seas that will operate over multiple decades. Some systems are already collecting high-resolution data from surface, water column, seafloor, and sub-seafloor sensors linked to shore by satellite or cable connection in real or near-real time, along with samples and other data collected in a delayed mode. We expect that such observatories will contribute to answering major ocean science questions including: How can monitoring of factors such as seismic activity, pore fluid chemistry and pressure, and gas hydrate stability improve seismic, slope failure, and tsunami warning? What aspects of physical oceanography, biogeochemical cycling, and ecosystems will be most sensitive to climatic and anthropogenic change? What are natural versus anthropogenic changes? Most fundamentally, how are marine processes that occur at differing scales related? The development of ocean observatories provides a substantial opportunity for ocean science to evolve in Europe. Here we also describe some basic attributes of network design. Observatory networks provide the means to coordinate and integrate the collection of standardised data capable of bridging measurement scales across a dispersed area in European Seas adding needed certainty to estimates of future oceanic conditions. Observatory data can be analysed along with other data such as those from satellites, drifting floats, autonomous underwater vehicles, model analysis, and the known distribution and abundances of marine fauna in order to address some of the questions posed above. Standardised methods for information management are also becoming established to ensure better accessibility and traceability of these data sets and ultimately to increase their use for societal benefit. The connection of ocean observatory effort into larger frameworks including the Global Earth Observation System of Systems (GEOSS) and the Global Monitoring of Environment and Security (GMES) is integral to its success. It is in a greater integrated framework that the full potential of the component systems will be realised. Crown Copyright (C) 2011 Published by Elsevier Ltd. All rights reserved.
Progress In Oceanography (0079-6611) (Pergamon-elsevier Science Ltd), 2011-10 , Vol. 91 , N. 1 , P. 1-33

Droits : 2011 Published by Elsevier Ltd. All rights reserved.
http://archimer.ifremer.fr/doc/00044/15557/15923.pdf
DOI:10.1016/j.pocean.2011.05.001
http://archimer.ifremer.fr/doc/00044/15557/