Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We review the evolution of concepts on and methods of estimating the state of stress from fault movements. Theories of failure in isotropic materials suggested a simple geometrical construction of optimal principal stress directions from a fault plane and its associated slip. These optimal directions align shear stress and slip directions and maximize the difference between shear stress and frictional resistance on the fault plane. Optimal stress directions for calcite twinning are obtained by a similar construction, with the difference that they maximize shear stress. Force representation of seismic sources independently introduced pressure, P, and tension, T, axes at positions that also maximize shear stress on both nodal planes. Frictional slip theory and the constraint that slip and shear stress directions be parallel allowed to address reactivation of pre-existing faults. This suggested that stress could also be inverted from reactivated fault and slip data or earthquake focal mechanisms. Early methods relied on geometrical constructions as a substitute for calculations, whereas later methods relied on software as these calculations became tractable with the help of computers. Similar methods were developed for the inversion of stress from crystal twin gliding with non-optimal geometry, with a different criterion that relies on a threshold of the component of shear stress along the gliding line. Even though these methods seek a common stress tensor compatible with fault and slip data, their main use is to separate polyphase data into homogeneous subsets and help deciphering complex tectonic histories. Fault and slip data can also be analyzed to constrain the strain rather than the stress tensor. In most cases this involves a summation and yields an average strain for the considered rock volume. Stress inversion thus appears better suited for differentiating heterogeneous data whereas strain analysis appears better suited for homogenizing them.
ISSN: 0040-1951

hal-00759043
https://hal.archives-ouvertes.fr/hal-00759043
DOI : 10.1016/j.tecto.2012.02.009

Éditeur(s) : HAL CCSD E Schweizerbart Science Publishers
Résumé : International audience
Mass balance calculations have been performed through a comparison of published graphical and statistical approaches applied to two contrasted geological settings: (i) the development of a greenschist-facies ductile shear-zone that recorded a weak volume change but significant mass transfers, and (ii) the formation of exoskarns in metacarbonate xenoliths that recorded a large volume decrease related to huge mass transfers. The comparison of the four mass-balance approaches shows that, if uncertainties are ignored, (1) they yield similar results concerning the mobile vs immobile behaviour of many components; (2) they yield similar mass-change values on bulk rock and on individual chemical elements (bulk-rock mass-change values differ by a maximum of ca. 15 % between graphical and statistical treatments of the metacarbonate xenolith evolution). The main difference concerns the uncertainties on mass changes (for bulk rocks and individual elements), which are much larger with the graphical than with the statistical approaches when uncertainties on chemical elements are taken into account, as they should be.The main advantage of the graphical methods is their rapid implementation and the clarity of the diagrams. Their main disadvantages are that uncertainties on each chemical element and bulk compositions are not taken into account and the difficulty in choosing an accurate immobility field to precisely define errors. Graphical methods need to be completed by a statistical treatment that gives absolute mass transfer results. The statistical approaches have the advantage of taking into account the chemical heterogeneities of the compared populations, in conjunction to a precise data treatment. The statistical treatment is an important and necessary step to decipher and to be pertinent in interpreting mobility/immobility of chemical elements, and, thus, in the absolute quantification of mass and volume changes.
ISSN: 0935-1221

hal-01260258
https://hal.archives-ouvertes.fr/hal-01260258
DOI : 10.1127/ejm/2015/0027-2475

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Detailed structural and petrological mapping in the Beni Bousera peridotite (Rif Belt, northern Morocco) shows that this orogenic peridotite massif is composed of four tectono-metamorphic domains with consistent kinematics, marked by a pervasive, shallowly dipping foliation with a NW-SE stretching lineation that progressively rotates towards a NNE-SSW orientation in the lowermost part of the massif. From top to bottom, these domains are garnet-spinel mylonites, Ariègite subfacies fine-grained porphyroclastic spinel peridotites, Ariègite-Seiland subfacies porphyroclastic, and Seiland subfacies coarse-porphyroclastic to coarse-granular spinel peridotites. Microstructures and crystal preferred orientations point to deformation dominantly by dislocation creep in all domains, but the continuous increase in average olivine grain size indicates decreasing plastic work rates from top to bottom. This evolution in deformation conditions is consistent with the change in synkinematic pressure and temperature conditions, from 900°C at 2*0 GPa in garnet-spinel mylonites to 1150°C at 1*8 GPa in the Seiland domain. A pervasive diffuse dunitic-websteritic layering subparallel to the foliation suggests deformation in the presence of melt in the Seiland domain. Gravitational instabilities owing to local melt accumulation may account for <200 m wide areas exhibiting a vertical lineation in this domain. To account for the consistent kinematics and the tectono-metamorphic evolution, which implies a temperature gradient of c. 125°C km−1 preserved across the Beni Bousera massif, we propose that the entire massif records the functioning of a low-angle shear zone, a few kilometres wide, which accommodated exhumation of the base of the lithosphere from ∼90 to ∼60 km depth. Partial melting in the Seiland domain may be explained by fast decompression of the footwall, without the need for exotic heat sources. Moreover, if the present-day orientation of the shear zone is similar to that when it was active in the mantle, the stretching lineations at high angle to the metamorphic gradient imply that shearing parallel to the trend of the belt accompanied thinning; that is, a transtensional deformation of the margin.
ISSN: 0022-3530

hal-00950056
https://hal.archives-ouvertes.fr/hal-00950056
DOI : 10.1093/petrology/egt067

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : International audience
We calculated the seismic properties of 47 mantle xenoliths from 9 kimberlitic pipes in the Kaapvaal craton based on their modal composition, the crystal-preferred orientations (CPO) of olivine, ortho- and clinopyroxene, and garnet, the Fe content of olivine, and the pressures and temperatures at which the rocks were equilibrated. These data allow constraining the variation of seismic anisotropy and velocities within the cratonic mantle. The fastest P and S2 wave propagation directions and the polarization of fast split shear waves (S1) are always subparallel to olivine [100] axes of maximum concentration, which marks the lineation (fossil flow direction). Seismic anisotropy is higher for high olivine contents and stronger CPO. Maximum P wave azimuthal anisotropy (AVp) ranges between 2.5 and 10.2% and the maximum S wave polarization anisotropy (AVs), between 2.7 and 8%. Changes in olivine CPO symmetry result in minor variations in the seismic anisotropy patterns, mainly in the apparent isotropy directions for shear wave splitting. Seismic properties averaged over 20 km-thick depth sections are, therefore, very homogeneous. Based on these data, we predict the anisotropy that would be measured by SKS, Rayleigh (SV) and Love (SH) waves for five endmember orientations of the foliation and lineation. Comparison to seismic anisotropy data from the Kaapvaal shows that the coherent fast directions, but low delay times imaged by SKS studies, and the low azimuthal anisotropy with with the horizontally polarized S waves (SH) faster than the vertically polarized S wave (SV) measured using surface waves are best explained by homogeneously dipping (45°) foliations and lineations in the cratonic mantle lithosphere. Laterally or vertically varying foliation and lineation orientations with a dominantly NW-SE trend might also explain the low measured anisotropies, but this model should also result in backazimuthal variability of the SKS splitting data, not reported in the seismological data. The strong compositional heterogeneity of the Kaapvaal peridotite xenoliths results in up to 3% variation in density and in up to 2.3% variation of Vp, Vs, and Vp / Vs ratio. Fe depletion by melt extraction increases Vp and Vs, but decreases the Vp / Vs ratio and density. Orthopyroxene enrichment due to metasomatism decreases the density and Vp, strongly reducing the Vp / Vs ratio. Garnet enrichment, which was also attributed to metasomatism, increases the density, and in a lesser extent Vp and the Vp / Vs ratio. Comparison of density and seismic velocity profiles calculated using the xenoliths' compositions and equilibration conditions to seismological data in the Kaapvaal highlights that (i) the thickness of the craton is underestimated in some seismic studies and reaches at least 180 km, (ii) the deep sheared peridotites represent very local modifications caused and oversampled by kimberlites, and (iii) seismological models probably underestimate the compositional heterogeneity in the Kaapvaal mantle root, which occurs at a scale much smaller than the one that may be sampled seismologically.
ISSN: 1869-9510

hal-01053516
https://hal.archives-ouvertes.fr/hal-01053516
DOI : 10.5194/se-5-45-2014

Éditeur(s) : HAL CCSD SpringerOpen
Résumé : The Karakorum Fault zone (KFZ) plays an important role in understanding the formation, evolvement and deformation of the Tibetan Plateau. The high-T dextral shearing metamorphic rocks, e.g., mylonites or mylonitized gneisses-granites, locally crop out along the southeastern part of the KFZ in the Ayila Ri'gyü Range area. The SHRIMP U-Pb dating of the syn-kinematic crystallized zircons indicates that the initial age of the KFZ is ∼27 Ma, ∼10 Ma older than previous results. The extensive high-T dextral shearing along the KFZ started at least at 27–20 Ma, accompanied by the syn-kinematic emplacement of leuco-granites. Deformation and concomitant fluid circulation during shearing most likely occurred as early as at 25–13 Ma. The KFZ probably grew from southeast to northwest along the fault as a result of continuous convergence between the India plate and Eurasia plate.
ISSN: 1001-6538

hal-00406402
https://hal.archives-ouvertes.fr/hal-00406402
DOI : 10.1007/s11434-007-0164-6

Éditeur(s) : HAL CCSD
Résumé : International audience
Tin mineralization in Achmmach deposit (NE of Moroccan Central Massif) is associated with tourmaline-rich alteration halos and faults, within N70 shear zones, hosted in sandstones and metapelites of the Upper Visean-Namurian. Such deposits were reported as late-Variscan in age and related to the emplacement of late orogenic granite not outcropping in the studied area.From field constraints, it appears that the late Variscan phase is marked by a transition from transpression to extension with conditions of deformation evolving from ductile to brittle environments. During the transpressive phase (horizontal shortening direction roughly trending E-W), pervasive tourmaline is deposited under the form of metasomatic halos around fractures in the upper levels relative to the deep batholith. This hydrothermal activity is coeval with ductile shear zones within a large corridors trending N70. Tourmaline-rich alteration appears as a hardening stage contributing to the modification of the tectonic style of rocks. Thereafter, a strong brecciation occurs in response of re-using and re-opening of the strike-slip structure. The result is (1) the formation of dextral (N070, N020) and sinistral (N120) shears, and (2) the circulation of fluids within early tourmalinites and formation of tourmaline-rich breccia. Subsequently, during the late orogenic extensional phase, tourmalinite breccias reopened as normal faults acting as overpressure fluid pathways for developing other breccias and veins. Such event is marked by deposition of tin mineralization i.e., cassiterite followed by sulphides, and then fluorite and carbonates at the end.From analysis of the shear-zone structure and superimposition of tourmalines and tin mineralization in the same structures, it is possible to suggest a structural control continuum. Such control is well expressed during metasomatism and deposition of hydrothermal tourmaline under the transpressive phase. Thereafter, under the extensive phase allowing open-space, tin-mineralization were trapped.This study has been supported by AI MA/09/210
24ème RST
Pau, France

insu-01546927
https://hal-insu.archives-ouvertes.fr/insu-01546927

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In the Arokam Tenere, the three studied massifs of granitoids are located around the N-S oriented Raghane mega-shear zone, which separates two of the main domains of the Tuareg shield, the Saharan metacraton and the Central Hoggar. The field observations, AMS analyses and U-Pb zircon dating were completed by a study of Landsat images because of the scarcity of outcrops in several parts of the studied area.;The image analysis allows to distinguish Arokam-East and Abdou granitoids in the eastern plutonic complex. It has also shown that the western plutonic complex corresponds to two different intrusions: the Yvonne granite and granodiorite. This is confirmed by the magnetic fabric that presents different characteristics in the different granitoids. U-Pb zircon dating and field observations show that the Arokam-West basement granite is much older (1915 Ma) than the Hanane granodiorite (582 Ma) in the central plutonic complex. Arokam-East and -West granites then belong to the Eburnean basement. The magnetic fabric of these granites is mainly associated with a post-magmatic deformation, probably of Pan-African age. Yvonne granodiorite is likely contemporaneous of the main displacement along the Raghane shear zone. The Yvonne granite (594 Ma) and Hanane granodiorite have a fabric similar to that previously obtained in most plutons of the Tiririne area. This fabric is related to the regional stress field, associated with the activity of the Raghane shear zone, during the late-magmatic phase in the plutons. On the contrary, the magnetic fabric of the Abdou pluton is still reflecting only the magma flow.
ISSN: 0899-5362

hal-00617478
https://hal.archives-ouvertes.fr/hal-00617478
DOI : 10.1016/j.jafrearsci.2011.02.007

Éditeur(s) : HAL CCSD American Physical Society
Résumé : International audience
We investigate a class of granular materials characterized by the possibility of interlocking between the particles. The interlocking is modeled by its effect through rolling resistance depending on relative rotation and normal force at the contact points and involving a single parameter analogous to the sliding friction coefficient. The model, which is introduced in the framework of the contact dynamics, method, is applied to simulate the simple shear of a large granular sample. We present a detailed analysis regarding the influence of rolling and sliding friction parameters on the macroscopic response in terms of shear strength, fabric properties, and force transmission. Interestingly, two distinct regimes can be distinguished in which the steady-state shear strength is controlled by either rolling resistance or sliding friction. The relative contributions of rolling and sliding contacts to the shear strength are consistent with the same two regimes. Interlocking strongly affects the force network by enhancing the arching effect and thus increasing the relative importance of weak contact forces and torques, which is reflected in a decreasing power-law probability distribution of the contact forces and torques below the mean. Due to the combined effect of friction and interlocking, the force-carrying backbone takes an increasingly columnar aspect involving a low fraction of particles. Our data suggest that the nature of the weak contact network is strongly affected by the formation of these columns of particles which do not need to be propped laterally. In particular, in the limit of high rolling resistance and sliding friction, the role of the weak network of contacts is no longer to prop the force chains, but, like the strong contact network, to actively sustain the deviatoric load imposed on the system.
ISSN: 1539-3755

hal-00412020
https://hal.archives-ouvertes.fr/hal-00412020
DOI : 10.1103/PhysRevE.78.021301

Éditeur(s) : HAL CCSD Elsevier
Résumé : Upper mantle flow beneath the French Massif Central is investigated using teleseismic shear wave splitting induced by seismic anisotropy. About 25 three component stations (short period, intermediate and broad-band) were installed during the period 1998-1999 in the southern Massif Central, from the Clermont Ferrand volcanic area to the Mediterranean sea. Teleseismic shear waves (SKS, SKKS and PKS) were used to determine the splitting parameters: the fast polarization direction and the delay time. Delay times ranging between 0.7 and 1.5 s have been observed at most of the sites. The azimuths of the fast split shear waves trend homogeneously NW-SE in the southern Massif Central suggesting a homogeneous mantle flow beneath this area. The observed NW-SE direction differs from the N100°E Pyrenean anisotropy further South. It does not appear to be correlated to Hercynian structures nor to the present-day motion of the plate but is well correlated to the Tertiary extension direction. We propose that the opening of the western Mediterranean induced by the rotation of the Corsica-Sardinia lithospheric bloc and the roll-back to the SE of the Tethys slab may have generated a large asthenospheric mantle flow beneath the southern Massif Central and a deflection of the up going plume centered beneath the northern Massif Central toward the SE.
ISSN: 0012-821X

insu-00150214
https://hal-insu.archives-ouvertes.fr/insu-00150214
https://hal-insu.archives-ouvertes.fr/insu-00150214/document
https://hal-insu.archives-ouvertes.fr/insu-00150214/file/Barruol_Granet_EPSL2002_hal.pdf
DOI : 10.1016/S0012-821X(02)00752-5

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We analyze in this study a new set of marine data including 3D local tomography, 1992-2008 relocated earthquakes and two recent multichannel seismic lines to characterize the deformation style in the collision area offshore east Taiwan. We have mapped in detail the Mohos of the converging plates as well as the subduction interface with a resolution never reached before. We show that the sharp continental subduction of the Eurasia plate, beneath the middle part of the Central Range, indents the Philippine Sea plate (PSP) as attested by intra-oceanic slicing and incipient subduction of the PSP beneath the east coast of Taiwan. The westernmost part of the PSP slab is probably experiencing a beginning of break-off as attested by NW-trending en-échelon shear zones beneath the southern slope of the southern Ryukyu arc (SRA). These en-échelon shear zones have a sinistral component favored by the "collision-free" subduction of the PSP north of 24°30′N. The down-faulting of the subduction interface forms ramps along which earthquakes clusterize. Three M7 subduction earthquakes occurred offshore Suao city along these ramps with a recurrence interval of about 40 years: 1920 Mw7.7, 1963 Mw7.2 and 2002 Mw7.1 events. The 1966 Mw6.0-7.5 earthquakes sequence likely outlines a WNW-ESE left-lateral intra-slab shear zone. The SRA upper plate accommodates the complex geometry and deformation of the subducting PSP through seismic deformation. Shallow high velocities fringing the Luzon volcanic arc (LVA) beneath the Longitudinal Valley and north of the southernmost Ryukyu forearc basins are interpreted as relics of the LVA forearc basement squeezed in the collision zone. Based on the accommodation of a large part of the convergence through shortening within the PSP and the subsequent segmentation of the shallow subduction interface, we consider that the nucleation of a Mw ≥ 8 earthquake along the southernmost Ryukyu megathrust is unlikely.
ISSN: 0040-1951

hal-00853365
https://hal.archives-ouvertes.fr/hal-00853365
https://hal.archives-ouvertes.fr/hal-00853365/document
https://hal.archives-ouvertes.fr/hal-00853365/file/publallemandifremer.pdf
DOI : 10.1016/j.tecto.2013.03.020

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The 40Ar/39Ar geochronological technique has significantly contributed to the study of crustal deformation. However, the frequent occurrence of extraneous argon in high-pressure terrains can make the interpretation of 40Ar/39Ar ages problematic. This contribution attempts to: i) characterize the distribution and origin of extraneous argon in the Cycladic Blueschist Unit (CBU, Greece) by applying the 40Ar/39Ar dating technique on three Cycladic islands, Syros, Tinos and Ios, which span a complete transect of the CBU and ii) discuss regional implications for the tectonometamorphic evolution of the CBU. Our results, combined with ages available in the literature, show that periods of peak-burial conditions (55–49 Ma) and syn- (45–38 Ma) to post-orogenic exhumation (37–21 Ma) are well constrained in the CBU by the 40Ar/39Ar method. Moreover, Variscan apparent ages are preserved in the Cycladic basement of Ios, indicating that the 40Ar/39Ar system was not completely reset during the Eocene metamorphic episode. Additionally, our 40Ar/39Ar data show that the occurrence of extraneous argon is heterogeneously distributed in the CBU. While high-pressure rocks of Syros and Tinos are only locally affected, extraneous argon is clearly evidenced in the CBU of Ios, yielding geologically meaningless ages up to 900 Ma. On each island, the most affected ages were obtained in microstructures where fluid circulation is enhanced such as shear bands or strain shadows around garnets. We suggest that the Cycladic Basement, a polymetamorphic continental unit, behaved as an argon reservoir that has been mobilized by fluid circulation at the Eocene. These argon-enriched fluids have then heterogeneously contaminated metamorphic rocks when percolating through the CBU. Finally, we claim that a minimum closure temperature of 550 °C must be accepted for the phengites of the CBU and conclude that volume diffusion is not the main process resetting the argon isotopic system in high-pressure rocks compare to recrystallization enhanced by fluid circulation and deformation.
ISSN: 0024-4937

Droits : http://creativecommons.org/licenses/by-nc-nd/
insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268
https://hal-insu.archives-ouvertes.fr/insu-01424268/document
https://hal-insu.archives-ouvertes.fr/insu-01424268/file/Valentin-Lithos-Accepted-2016.pdf
DOI : 10.1016/j.lithos.2016.12.013

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Structural analysis along with 40Ar–39Ar and U–Pb datings in the Fuping massif provide new insight into the evolution of the eastern part of the Trans-North China Belt (North China Craton), from 2.7 Ga to 1.8 Ga. D1 is responsible for the development of a dome-and-basin structure coeval with crustal melting giving rise to migmatite and Nanying gneissic granites at 2.1 Ga. This dome-and-basin architecture resulted from the interference between a N–S compression of a weak ductile crust and gravity-driven vertical flow, in a high thermal regime. The next events involved flat lying ductile thrusting (D2) and normal faulting (D3) dated at around 1880 Ma and 1830 Ma, respectively. The D2 and D3 events belong to the Trans-North China Orogeny that results in the final amalgamation of the North China Craton. The D1 deformation is considered as evidence for an earlier orogen developed around 2.1 Ga prior to the Trans-North China Orogeny. The change in the deformation style between the 2.1 Ga and 1.8 Ga could be viewed as a consequence of the cooling of the continental crust in the North China Craton.
ISSN: 0191-8141

insu-00309553
https://hal-insu.archives-ouvertes.fr/insu-00309553
https://hal-insu.archives-ouvertes.fr/insu-00309553/document
https://hal-insu.archives-ouvertes.fr/insu-00309553/file/Trap-JStructuralGeology-2008.pdf
DOI : 10.1016/j.jsg.2008.05.001

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
The Alboran Domain, situated at the western end of the Mediterranean subductionsystem, is characterized by the Ronda Peridotites, one of the world largest exposures of subcontinental mantle. Using U-Pb (LA-ICP-MS) and Ar-Ar dating, we precisely dated twotectonic events associated with the Tertiary exhumation of the Ronda Peridotites. First,shearing along the Crust-Mantle Extensional Shear Zone caused, at ca. 22.5 Ma, mantleexhumation, local partial melting in the deep crust and coeval cooling in the upper crust.Second, the Ronda Peridotites Thrust triggered the final crustal emplacement of theperidotites onto the continental crust at ca. 21 Ma, as testified by granitic intrusions in thethrust hanging-wall. The tectonic evolution of the western Alboran Domain is thereforecharacterized by a fast switch from a continental lithosphere extension in a backarc setting,with sub-continental mantle exhumation, to a rift inversion by thrusting driven by shorteningof the subduction upper plate
ISSN: 0954-4879

insu-01441962
https://hal-insu.archives-ouvertes.fr/insu-01441962
https://hal-insu.archives-ouvertes.fr/insu-01441962/document
https://hal-insu.archives-ouvertes.fr/insu-01441962/file/Frasca-TerraNova-2017.pdf
DOI : 10.1111/ter.12255

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
How reliable are shear wave splitting measurements as a means of determining mantle flow direction? This remains a topic of debate, especially in the context of subduction. The answer hinges on whether our current understanding of mineral physics provides enough to accurately translate between seismic observations and mantle deformation. Here, we present an integrated model to simulate strain-history-dependent texture development and estimate resulting shear wave splitting in subduction environments. We do this for a mantle flow model that, in its geometry, approximates the double-sided Molucca Sea subduction system in Eastern Indonesia. We test a single-sided and a double-sided subduction case. Results are compared to recent splitting measurements of this region by Di Leo et al. (2012a). The setting lends itself as a case study, because it is fairly young and, therefore, early textures from the slab's descent from the near surface to the bottom of the mantle transition zone--which we simulate in our models--have not yet been overprinted by subsequent continuous steady state flow. Second, it allows us to test the significance of the double-sided geometry, i.e., the need for a rear barrier to achieve trench-parallel subslab mantle flow. We demonstrate that although a barrier amplifies trench-parallel subslab anisotropy due to mantle flow, it is not necessary to produce trench-parallel fast directions per se. In a simple model of A-type olivine lattice-preferred orientation and one-sided subduction, trench-parallel fast directions are produced by a combination of simple shear and extension through compression and pure shear in the subslab mantle.
ISSN: 1525-2027

hal-01053506
https://hal.archives-ouvertes.fr/hal-01053506
DOI : 10.1002/2013GC005032

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
Determination of the membrane seal capacity of deformation bands is critical for managing geologic reservoirs in porous sandstones. In this study, we have analyzed a cataclastic shear-band network developed in uncemented porous sandstone in Provence, France. Geometrical analyses of the bands show significant differences between three types of bands (single strand, multistrand, and band cluster), sorted by their number of strands, their amount of shear displacement, and their thicknesses. At the microscopic scale, the image-analysis porosities and the grain-size distributions allow definition of three different types of microstructural deformation: damage zone, protocataclastic, and cataclastic. Whereas damage zone and protocataclastic deformations are observed in each type of band, cataclastic strands are observed in clusters and, sometimes, in multistrands. Cataclastic strands are characterized by a porosity reduction of 10 to 25% and a permeability reduction of three to five orders of magnitude compared to the host rock. Field observations of iron hydroxide precipitations around the bands suggest that cataclastic strands were membrane seals to water flow under vadose condition. This study therefore highlights the importance of the degree of cataclasis in shear bands as membrane seals to subsurface fluid flows in sandstone reservoirs.
ISSN: 0149-1423

hal-00766557
https://hal.archives-ouvertes.fr/hal-00766557
DOI : 10.1306/04051211097

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Geodetic data support a short-term continental deformation localized in faults bounding lithospheric blocks. Whether major "faults" observed at the surface affect the lithospheric mantle and, if so, how strain is distributed are major issues for understanding the mechanical behavior of lithospheric plates. A variety of evidence, from direct observations of deformed peridotites in orogenic massifs, ophiolites, and mantle xenoliths to seismic reflectors and seismic anisotropy beneath major fault zones, consistently supports prolongation of major faults into the lithospheric mantle. This review highlights that many aspects of the lithospheric mantle deformation remain however poorly understood. Coupling between deformation in frictional faults in the uppermost crust and localized shearing in the ductile crust and mantle is required to explain the post-seismic deformation, but mantle viscosities deduced from geodetic data and extrapolated from laboratory experiments are only reconciled if temperatures in the shallow lithospheric mantle are high (> 800 °C at the Moho). Seismic anisotropy, especially shear wave splitting, provides strong evidence for coherent deformation over domains several tens of km wide in the lithospheric mantle beneath major transcurrent faults. Yet it cannot detect narrow strain localization zones or shallowly dipping faults. Seismic profiling images shallow-dipping seismic reflectors in the lithospheric mantle interpreted as the continuation of normal or, less frequently, inverse faults in the mantle. However the nature of these reflectors is poorly understood. There is a large discrepancy between the scale at which deformation processes are studied (a few kilometers, at most, due to the limited size of continuous mantle exposures at the Earth's surface) and the scale inferred for strain localization in the mantle from geophysical observations (tens of kilometers). Combining data on deformation microstructures and crystal preferred orientations in naturally deformed peridotites and seismologic observations allows nevertheless discussing strain localization processes that may play a role on the development of mantle shear zones.
ISSN: 0040-1951

hal-00750314
https://hal.archives-ouvertes.fr/hal-00750314
DOI : 10.1016/j.tecto.2012.06.006

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Upper-mantle flow beneath the South Pacific is investigated by analysing shear wave splitting parameters at eight permanent long-period and broad-band seismic stations and 10 broad-band stations deployed in French Polynesia from 2001 to 2005 in the framework of the Polynesian Lithosphere and Upper Mantle Experiment (PLUME). Despite the small number of eventsand the rather poor backazimuthal coverage due to the geographical distribution of the natural seismicity, upper-mantle seismic anisotropy has been detected at all stations except at Tahiti where two permanent stations with 15 yr of data show an apparent isotropy. The median value of fast polarization azimuths (N67.5°W) is parallel to the present Pacific absolute platemotion direction in French Polynesia (APM: N67°W). This suggests that the observed SKS fast polarization directions result mainly from olivine crystal preferred orientations produced by deformation in the sublithospheric mantle due to viscous entrainment by the moving Pacific Plate and preserved in the lithosphere as the plate cools. However, analysis of individualmeasurements highlights variations of splitting parameters with event backazimuth that imply an actual upper-mantle structure more complex than a single anisotropic layer with horizontal fast axis. A forward approach shows that a two-layer structure of anisotropy beneath French Polynesia better explains the splitting observations than a single anisotropic layer. Second ordervariations in the measurements may also indicate the presence of small-scale lateral heterogeneities. The influence of plumes or fracture zones within the studied area does not appear to dominate the large-scale anisotropy pattern but may explain these second-order splitting variations across the network.
ISSN: 0956-540X

hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275/document
https://hal.archives-ouvertes.fr/hal-01249275/file/GJI2007SKS.pdf
DOI : 10.1111/j.1365-246X.2007.03475.x

Résumé : L’objet de cette thèse est l’étude des comportements mécanique et à la corrosion d’un nouveau système de fondation, dit pieux SPIRMEC, adapté aux structures légères. Le travail s’est focalisé sur deux grands aspects. Le premier aspect concerne l’analyse du comportement sous chargement axiale des pieux SPIRMEC sur la base de l’expérimentation et de la modélisation numérique dans un sol mou non cohésif. Quant au deuxième aspect, il traite du problème de la corrosion de l’acier constituant le pieu dans un environnement tropical humide. Le comportement des pieux SPIRMEC sous une charge axiale de traction, dans un sol fin non cohésif, a montré le développement d’une surface cylindrique de rupture. Celle-ci ne dépend pas de la configuration géométrique des pieux tel que : l’espacement S, le diamètre d’hélice Dh et le diamètre du tube d. En adoptant ce critère de rupture et à l’aide d’une analyse statistique des données, nous avons proposé quatre méthodes analytiques de prédiction de la capacité portante des pieux SPIRMEC à partir des essais in-situ et au laboratoire qui sont: •Méthode CPT basée sur la résistance de pointe pénétromètrique (essai CPT), •Méthode MPT basée sur la pression limite pressiomètrique (essai MPT), •Méthode du couple d’installation, •Méthode analytique basée sur les paramètres de cisaillement de sol notamment l’angle de frottement interne (essais triaxial et boîte de cisaillement). Ces méthodes tiennent compte de la géométrie du pieu, du procédé de mise en oeuvre et de la compacité du sol. L’analyse de performance des méthodes proposées a montré que les méthodes analytique et CPT représentent mieux le comportement des pieux testés. La modélisation numérique du comportement des pieux SPIRMEC sous charge axiale de traction a été également étudiée à l’aide du code de calcul Plaxis 2D. Un modèle axisymétrique a été adopté pour modéliser la géométrie de la structure. Le modèle de comportement hardening soil a été retenu pour modéliser le comportement élastoplastiq des couches de sol. Un modèle élastique linéaire a été retenu pour le pieu. Quant au comportement de l’interface sol-structure, il a été pris en compte par un modèle élastoplastique basé sur les critères de Mohr-Coulomb. L’expansion du sol résultant de l’installation des pieux a été approchée par une cavité cylindrique. Cette dernière a été modélisée par des déformations volumiques anisotropes. Nous avons constaté, qu’appliquer une déformation volumique de l’ordre de 40% permet une bonne concordance entre les résultats numériques et expérimentaux. L’étude paramétrique nous a également permis de constater l’existence d’une variation linéaire entre la capacité portante et l’espacement S. Le comportement de l’acier galvanisé dans le sol a été également étudié au moyen de trois approches: électrochimique, visuelles grâce au microscope électronique et gravimétrique. Les tests électrochimiques de corrosion du zinc ont été réalisés dans la solution de sol artificielle pour deux périodes bien distinctes : saison des pluies et après 8 mois de contact sol-pieu. Une forte dépendance est constatée de la vitesse de corrosion de zinc au pH et à la conductivité de la solution. La vitesse de corrosion est plus importante en saison des pluies qu’après 8 mois de contact de pieu avec le sol. Les fortes concentrations en sulfates semblent augmenter la vitesse de corrosion. Les analyses menées au MEB montrent que la zone de fluctuation de nappe et en surface externe (sol/air) sont les zones les plus corrodées. La comparaison entre les différentes techniques d’évaluation de la vitesse de corrosion a montré que l’eau de nappe peut être utilisée comme un milieu représentatif du profil chimique d’un sol non cohésif et légèrement granulaire.
The purpose of this thesis is to study the both behaviors mechanical and of the corrosion of a new foundation system, called spirec piles, for lightweight structures. The work was based on two main aspects. The first aspect concerns the analysis of behavior of the spirmec piles under axial loading on the basis of experimental and numerical modeling in a non-cohesive soft soil. On the second aspect, it addresses the problem of corrosion of steel forming the pile in a humid tropical environment. The behavior of the tested piles under axial traction load, in a non-cohesive soil, showed the development of a cylindrical surface of failure. This does not depend on the geometrical configuration of the tested piles such that: the spacing s, the helix diameter dh and the diameter of the shaft. By adopting this failure criterion and using statistical data analysis, we proposed four analytical methods for predicting the bearing capacity of the piles from in-situ and laboratory tests, which are: cpt method based on tip resistance penetrometer (cpt test), mpt method based on pressuremeter limit pressure (test mpt), method of installation torque and analytical method based on the shear parameters of soil (triaxial tests and shear box). These methods take into account the geometry of the pile, the method and implementation of soil compaction. Performance analysis of the proposed methods showed that the analytical methods and cpt represent better the behavior of piles tested. An axisymmetric condition was assumed to model this geometry in two-dimensional space. In this study, we proposed to model the pipe screw pile with plates elements available in plaxis 2d. The helixes were modeled as circular disks. Interface elements were incorporated along the pile to simulate the soil-pile interaction. Hardening soil model was chosen to describe the soil with drained behavior was assigned for all layers. Linear elastic for pile and elastic plastic model based on the mohr-coulomb criterion was used to describe the interface behavior. The lateral expansion generated by the pile shaft was modeled by anisotropic volumetric strains (ɛxx=ɛzz, ɛyy=0). The pile behavior under tensile loading at different volumetric strains, it is clear that the best fit was obtained at volumetric strain of 40%. The parametric study also allowed us to establish the existence of a linear variation between the bearing capacity and spacings. The behavior of the galvanized steel in the ground has also been studied using three approaches such as: electrochemical, microscopic imaging and gravimetrically. Electrochemical tests of the corrosion of the zinc have been made in artificial soil solution into two periods, the rainy season and after eight months of contact soil-pile. Is a strong dependence of the observed corrosion rate of the zinc at the ph and conductivity of the solution. The corrosion rate is higher in the rainy season compared to eight months of contact of the pile with soil. High sulfate concentrations increase the rate of corrosion. The meb analysis shows that the fluctuation zone of the water table is the most corroded area. Comparison between the different methods of evaluating the corrosion rate showed that the ground water may be used as a representative profile of the chemical environment of a non-cohesive soil and slightly granular.

http://www.theses.fr/2014AGUY0790/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Chenaillet Ophiolite in the Franco-Italian Alps represents a well-exposed ocean-floor sequence that was only weakly overprinted by Alpine metamorphism during its emplacement in the Alpine nappe stack. Pillow lavas showing a Mid Ocean Ridge Basalt (MORB) signature overlie tectonically exhumed gabbros and serpentinized mantle rocks similar to oceanic core complexes (OCC) described from present-day slow- to ultraslow-spreading ridges. Based on detailed mapping it can be shown that: 1) syn-magmatic high-temperature shear zones are truncated by oceanic detachment faults; 2) sediments consisting exclusively of clasts derived from the footwall of the detachment are overlain by voluminous lavas, and 3) emplacement of lavas is linked with high-angle faulting that overprint the oceanic detachment fault. Based on stratigraphic and cross cutting relationships we conclude that: 1) a complex relation between high- and low-temperature shear zones exists, 2) oceanic detachment faults may be obliterated by later emplaced of MOR basalts, and 3) high-angle faults may serve at shallow levels as feeder channels for the overlying pillow basalts. These observations raise questions about the relative relations in time and space between magmatic, hydrothermal and tectonic processes at spreading systems. We propose that the observed change from exhumation along an oceanic detachment fault to high-angle faulting associated with extrusion of volcanic rocks may represent an evolution within a life cycle of a spreading system that may be comparable to present-day slow- to ultraslow-spreading ridges.
ISSN: 0024-4937

hal-00617678
https://hal.archives-ouvertes.fr/hal-00617678
DOI : 10.1016/j.lithos.2010.10.017

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
Detailed seafloor mapping in the area east of Taiwan revealed trench-parallel stretching and folding of the Ryukyu forearc and lateral motion of the accretionary wedge under oblique convergence. East of 122ø40'E, a steep accretionary wedge is elongated in an E-W direction. A major transcurrent right-lateral strike-slip fault accommodates the strain partitioning caused by an oblique convergence of 40 ø. A spectacular out-of-sequence thrust may be related to the subduction of a structural high lying in the axis of the N-S trending Gagua Ridge. This asperity is likely responsible for the uplift of the accretionary wedge and forearc basement and may have augmented strain partitioning by increasing the coupling between the two plates. West of 122ø40'E, the low-taper accretionary wedge is sheared in a direction subparallel to the convergence vector with respect to the Ryukyu Arc. The bayonet shape of the southern Ryukyu Arc slope partly results from the recent (re)opening of the southern Okinawa Trough at a rate of about 2 to 4 cm/yr. Right-lateral shearing of the sedimentary forearc with respect to the nonlinear Ryukyu backstop generates trench-parallel extension in the forearc sediment sequence at dilational jogs and trench-parallel folding at compressive jogs. The Hoping Basin lies above a diffuse trench/trench/fault (TTF) or TFF unstable triple junction moving toward the south along a N-S transform zone which accommodates the southward drift of the Ryukyu Arc with respect to Eurasia.
ISSN: 0278-7407

hal-01261555
https://hal.archives-ouvertes.fr/hal-01261555
https://hal.archives-ouvertes.fr/hal-01261555/document
https://hal.archives-ouvertes.fr/hal-01261555/file/Lallemand_et_al-1999-Tectonics.pdf
DOI : 10.1029/1998TC900011