Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
This study investigates three-dimensional flow modes of orogenic plateaus by means of physical modeling. Experiments consist of shortening two contiguous lithospheres of contrasting strength, one being a weak plateau-type lithosphere and the other a strong craton-type lithosphere. The lateral boundaries are either totally confined or allow escape toward a lateral foreland on one side. Two synconvergence flow regimes are distinguished, which are governed by the balance between the gravity potential and the strength of the plateau crust and the resistance of its lateral foreland. The first regime implies transversal (orogen-normal) injection of plateau lower crust into the collision zone as a result of confinement of the plateau by an increasingly stiffer lateral boundary. As a precursor mechanism to channel flow, transversal injection responds to downward thickening of the plateau crust that is forcedly extruded into the orogenic wedge. The second regime is that of collapse-driven lateral escape of the plateau. This regime is established after a threshold is attained in the interplate coupling in the collision zone, which allows the gravity potential of the plateau to overcome the resistance of its lateral boundary. Under the collapse-driven escape regime (orogen parallel), such as that governing Tibet during the last 13 Ma, most of the convergence in the plateau and the top and rear of the collisional wedge is transformed into lateral flow and extension.
ISSN: 0148-0227

hal-01229107
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01229107
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01229107/document
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01229107/file/2015JB012110_revised.pdf
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01229107/file/SupplementaryMaterial_final.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
We investigate flexural geometry and rheology of the India plate beneath the eastern Himalaya from a new gravity data set acquired in Bhutan. Compared to the well‒studied Nepal Himalaya, the obtained Bouguer anomaly profiles across the range show shorter wavelength flexure of the lithosphere with a narrower and shallower foreland basin. This new data set and seismic Moho constraints are interpreted together in terms of lithospheric flexure using a 2‒D thermomechanical model. Our results suggest that the strongest layer of the continental lithosphere beneath Bhutan is the upper mantle, as it is beneath Nepal. The observed west‒to‒east decrease in flexural wavelength is associated with weakening mantle rheology. The simulations show that this decrease can be related to ductile mantle behavior: either hydrated wet dunite or dry and hot olivine rheology. Both models display decoupled lithospheric layers leading to an eastward decrease of flexural rigidity from ∼1024 to ∼5*1022 N m in Nepal and Bhutan, respectively.
ISSN: 0094-8276

hal-00903564
https://hal.archives-ouvertes.fr/hal-00903564
DOI : 10.1002/grl.50793

Éditeur(s) : HAL CCSD
Résumé : The Deep Basin of the Gulf of Mexico (DBGM) extends over eastern Mexico, the southeastern part of the United States, west of the Atlantic Ocean. This study, based on the interpretation and integration of seismic profiles, exploration wells and outcrop studies, focus on the deep part of the Gulf of Mexico, where bathymetry varies from 200 to 3750 m, thus comprising both the continental slope and the abyssal plain. The first part of this thesis focus on the description of the sedimentary infill of the western part of the Gulf of Mexico, in the Veracruz State, and to its geodynamic controls. The geodynamic evolution of the Deep Basin of the Gulf of Mexico (DBGM) begins during the Triassic-Jurassic with the break-up and the opening of a continental rift, in the southern part of the North American lithospheric plate. This opening induced a relative movement of the Yucatan Block towards the southeast. This intra-continental rifting episode was followed by a stage of post-rift thermal subsidence in the basins of the continental margin in the west, coeval with oceanic accretion in the DBGM. The thermal subsidence of the margin was subsequently modified by the Laramian orogeny, which impacted strongly the overall architecture of the margin as well as its litho-stratigraphic evolution, inducing the deposition of siliciclastic deposits in various morphotectonic provinces: i.e., near the tectonic front of the Sierra Madre Oriental (SMO), within the adjacent Chicontepec foreland basin, over the Tuxpan Platform (Golden Lane), across the continental slope and up to the deep abyssal plain, these two last morphotectonic provinces belonging to the DBGM. During the Early Paleogene, the effects of the thermal subsidence of the passive margin were stressed by the tectonic load of the Laramian orogen (i.e., the Sierra Madre Oriental, SMO), thus allowing the development of a foreland basin flexural. In this geodynamic framework, the main sedimentary transfers developed from the tectonic front "SMO" in the west, towards the DBGM in the east, the main source for clastic sediments being linked to the erosion of the "SMO" mountains. During the Paleocene and the Early Eocene, the architecture of the silici-clastic syn-tectonic sediments deposited in submarine fans was characterized by sliding, turbidites with A and B Bouma facies, as well as levees and channels. After the stop of the flexural subsidence, the thermal subsidence of the passive margin resumed during the Late Eocene, the Oligocene and the Neogene, allowing the development of a new sedimentary prism, prograding eastwards toward the DBGM. This sedimentary infill was again made up of levees-channels, sand bars and delta systems. During the Neogene, an extensional system with listric faults and roll-over features developed across the slope of the DBGM, due to an active detachment developing within overpressured Eocene-Oligocene clays. This gravitational gliding of Neogene series accounted also for the development of compressional features at the toe of the slope. Approximately 60% of the Miocene siliciclastic sediments have been trapped in growth strata and slope basins associated with this complex gravitational system, ranging from river-delta features towards gravity slides associated with slump facies. The second part of this thesis aims at a quantification of these various processes, including the construction of balanced cross sections, forward Thrustpack kinematic modelling coupling the development of a basal detachment, lithospheric flexure, erosion and sedimentation, as well as subsequent stratigraphic modelling with the Dionisos software, the later aiming at predicting the sand versus clay ratios in Neogene siliciclastic deposits of the DBGM and its surroundings.
Le bassin profond du Golfe du Mexique (BPMG) est localisé à l'est du Mexique, au sud-est des États-Unis et à l'ouest de l'Océan Atlantique. Cette étude de la partie profonde du Golfe du Mexique est basée sur l'intégration de données de sismique, de forages pétroliers et d'études de terrain; elle comprend toute la pente continentale et la plaine abyssale, avec une bathymétrie qui varie de 200 à 3750 m. La première partie de cette thèse est consacrée à la description du remplissage sédimentaire de la bordure occidentale du Golfe du Mexique, dans le secteur de Veracruz, en liaison avec son évolution géodynamique. L'évolution géodynamique du BPMG commence au Trias-Jurassique avec la rupture et la propagation d'un rift continental, dans le secteur sud de la plaque nord américaine. Cette ouverture et le déplacement relatif vers le sud-est du bloc crustal du Yucatan sont à l'origine du BPGM. Cette géodynamique de rift continental est suivie d'une étape post-rift accompagnée de l'océanisation du bassin. Les bassins de la marge passive ont poursuivi leur évolution sous l'effet de la subsidence thermique à l'ouest du Golfe du Mexique, tandis que de la croûte océanique se formait dans le BPGM. Cette subsidence thermique de la marge a ensuite été perturbée par l'orogénèse Laramienne, qui a remodelé l'architecture stratigraphique silico-clastique des dépôts du Tertiaire entre les éléments morphotectoniques suivants: lefront tectonique de la Sierra Madre Orientale (SMO), le bassin d'avant-pays Chicontepec, la Plateforme de Tuxpan-Faja de Oro, la pente continentale et la plaine abyssale, ces deux dernières provinces morphotectoniques appartenant au BPGM. Pendant le Paléogèneinférieur, les effets de la subsidence thermique de la marge passive ont été accentués par la charge tectonique de l'orogénèse laramienne (SMO), permettant ainsi le développement d'un bassin flexural d'avant-pays. Au cours de cette étape, les principaux transferts sédimentaires se sont effectués du front tectonique "SMO" vers le BPGM. La source principale de sédiments clastiques est liée à l'érosion de la chaîne de montagnes "SMO". Pendant le Paléocène et l'Éocène inférieur, l'architecture des premiers sédiments silico-clastiques syn-tectoniques déposés dans des éventails sous-marins sont caractérisés par des figures de glissement, des faciès turbiditiques A et B de Bouma, des chenaux-levées. Après l'arrêt de la subsidence flexurale, la subsidence thermique de la marge passive s'est poursuivie pendant l'Éocène supérieur, l'Oligocène et le Néogène, permettant le développement d'un nouveau prisme sédimentaire progradant. Les remplissages sédimentaires sont encore constitués de chenaux et de levées, avec des barres de sable associées à des systèmes deltaïques sur la plateforme. Pendant le Néogène, un système de failles listriques s'est développé sur la pente du BPGM, au-dessus d'une surface de décollement située, dans la région d'étude, dans les argiles de l'Éocène-Oligocène. Ce système de failles de croissance a piégé plus de 60% des sédiments silico-clastiques du Miocène. Ce remplissage sédimentaire évolue latéralement de faciès fluviaux deltaïques vers des faciès de pente affectés de glissements gravitaires et associés à des turbidites. La deuxième partie de cette thèse est consacrée à une approche quantitative basée sur des modélisations structurales (coupes équilibrées et modélisations cinématiques directes avec Thrustpack, couplant décollement gravitaire, flexure lithosphérique, érosion et sédimentation), puis sédimentaires (prise en compte des transferts de matériel clastique depuis la partie émergée de la chaîne jusqu'au bassin profond, à l'aide du logiciel Dionisos, afin de mieux comprendre les processus de piégeage des sédiments grossiers dans les structures de croissance et les bassins perchés de la marge.
https://tel.archives-ouvertes.fr/tel-00435120

tel-00435120
https://tel.archives-ouvertes.fr/tel-00435120
https://tel.archives-ouvertes.fr/tel-00435120/document
https://tel.archives-ouvertes.fr/tel-00435120/file/thesealzaga.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
A network of 54 survey GPS sites, 28 continuous GPS stations and three absolute gravity (AG) observation sites have been set up in the Alborz mountain range to quantify the present-day kinematics of the range. Our results allow us to accurately estimate the motion of the South Caspian block (SCB) for the first time, and indicate rotation of the SCB relative to Eurasia, accounting for the left lateral motion in the Alborz range. In light of these new results, it clearly appears that deformation rates vary along the range, the eastern part accommodating mainly left lateral strike slip (2 mm yr(-1) south of the range and 5 mm yr(-1) north of the range) with a very low range normal shortening rate on the Khazar thrust fault (similar to 2 mm yr(-1)), and the western part accommodating range normal shortening (similar to 6 mm yr-1) on the Khazar thrust fault with a left lateral component of similar to 2 mm yr(-1) north of the range and 1 mm yr(-1) south of the range. These present-day kinematics agree with geomorphologic estimated slip rates, but not the long-term deformation, corroborating the idea that the kinematics of the range have changed recently due to the change of SCB motion.;Modelling of the interseismic deformation suggests a deep locking depth on the central-western segment of the Khazar fault (similar to 30 km) in agreement with the Baladeh earthquake rupture and aftershock ranging between 10 and 30 km. Given this unusual deep locking depth and the 34 degrees dip of the thrust, a large part of the Alborz range is located above the seismically coupled part of the fault. Based on our AG measurements this part of the range seems to uplift at a rate of 1-5 mm yr(-1), in agreement with terrace uplift.
ISSN: 0956-540X

hal-00617146
https://hal.archives-ouvertes.fr/hal-00617146
https://hal.archives-ouvertes.fr/hal-00617146v2/document
https://hal.archives-ouvertes.fr/hal-00617146/file/djamour2010.pdf
DOI : 10.1111/j.1365-246X.2010.04811.x

Éditeur(s) : Oxford Univ Press
Résumé : This study presents the results of a deep seismic survey across the north Algerian margin, based on the combination of 2-D multichannel and wide-angle seismic data simultaneously recorded by 41 ocean bottom seismometers deployed along a north-south line extending 180 km off Jijel into the Algerian offshore basin, and 25 land stations deployed along a 100-km-long line, cutting through the Lesser Kabylia and the Tellian thrust-belt. The final model obtained using forward modelling of the wide-angle data and pre-stack depth migration of the seismic reflection data provides an unprecedented view of the sedimentary and crustal structure of the margin. The sedimentary layers in the Algerian basin are 3.75 km thick to the north and up to 4.5-5 km thick at the foot of the margin. They are characterized by seismic velocities from 1.9 to 3.8 km s(-1). Messinian salt formations are about 1 km thick in the study area, and are modelled and imaged using a velocity between 3.7 and 3.8 km s(-1). The crust in the deep sea basin is about 4.5 km thick and of oceanic origin, presenting two distinct layers with a high gradient upper crust (4.7-6.1 km s(-1)) and a low gradient lower crust (6.2-7.1 km s(-1)). The upper-mantle velocity is constrained to 7.9 km s(-1). The ocean-continent transition zone is very narrow between 15 and 20 km wide. The continental crust reaches 25 km thickness as imaged from the most landward station and thins to 5 km over a less than 70 km distance. The continental crust presents steep and asymmetric upper- and lower-crustal geometry, possibly due to either asymmetric rifting of the margin, an underplated body, or flow of lower crustal material towards the ocean basin. Present-time deformation, as imaged from three additional seismic profiles, is characterized by an interplay of gravity-driven mobile-salt creep and active thrusting at the foot of the tectonically inverted Algerian margin.
Geophysical Journal International (0956-540X) (Oxford Univ Press), 2014-09 , Vol. 198 , N. 3 , P. 1486-1503

Droits : 2014 The Royal Astronomical Society
http://archimer.ifremer.fr/doc/00217/32836/32150.pdf
DOI:10.1093/gji/ggu179
http://archimer.ifremer.fr/doc/00217/32836/

Éditeur(s) : HAL CCSD Wiley
Résumé : Tropical forests contain an important proportion of the carbon stored in terrestrial vegetation, but estimated aboveground biomass (AGB) in tropical forests varies two-fold, with little consensus on the relative importance of climate, soil and forest structure in explaining spatial patterns. Here, we present analyses from a plot network designed to examine differences among contrasting forest habitats (terra firme, seasonally flooded, and white-sand forests) that span the gradient of climate and soil conditions of the Amazon basin. We installed 0.5-ha plots in 74 sites representing the three lowland forest habitats in both Loreto, Peru and French Guiana, and we integrated data describing climate, soil physical and chemical characteristics and stand variables, including local measures of wood specific gravity (WSG). We use a hierarchical model to separate the contributions of stand variables from climate and soil variables in explaining spatial variation in AGB. AGB differed among both habitats and regions, varying from 78 Mg ha−1 in white-sand forest in Peru to 605 Mg ha−1 in terra firme clay forest of French Guiana. Stand variables including tree size and basal area, and to a lesser extent WSG, were strong predictors of spatial variation in AGB. In contrast, soil and climate variables explained little overall variation in AGB, though they did co-vary to a limited extent with stand parameters that explained AGB. Our results suggest that positive feedbacks in forest structure and turnover control AGB in Amazonian forests, with richer soils (Peruvian terra firme and all seasonally flooded habitats) supporting smaller trees with lower wood density and moderate soils (French Guianan terra firme) supporting many larger trees with high wood density. The weak direct relationships we observed between soil and climate variables and AGB suggest that the most appropriate approaches to landscape scale modeling of AGB in the Amazon would be based on remote sensing methods to map stand structure.
ISSN: 1354-1013

hal-01374829
https://hal.archives-ouvertes.fr/hal-01374829
DOI : 10.1111/j.1365-2486.2011.02432.x
PRODINRA : 183370

Éditeur(s) : HAL CCSD
Résumé : International audience
The main biological function of reaction wood is to act as “muscle” for trees, enabling them to control their posture and right stems when they are permanently disturbed from their set-point inclination by gravity or winds. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called “maturation strains”. Moreover, this function is basically performed through the asymmetric formation of wood (in quantity or quality) around the tree circumference. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity, as an asymmetric force associated to maturation strains creates a bending moment (i.e. one side of the stem “pulls” the other one). We will discuss the traits (cross sectional size and shape, wood features as G fibers or microfibril angle, eccentric growth even in usual or extreme cases as buttresses, total biomass growth and height of center of mass, stem lean and set-point angle) involved to understand how the posture control works. We will give simple formulas to estimate a “muscle efficiency” from biomechanical modeling. We will give practical methods to estimate all the involved traits, especially maturation strains from direct and indirect measurements, in peripheral functional wood or by retrospective dendrochronological analysis. Then, we will illustrate how tree stem tropisms and especially gravitropism, widely studied by physiologists, are key processes in natural ecosystems, through practical examples from tropical rainforest tree communities and regeneration of European mixed beech forests. Using the previous definition of postural control efficiency, we will show that the cross section size is rapidly a limiting factor, opposing the extreme strategies of flexible small stems, which bend easily but also right themselves quickly, to stiff big stems. Lastly, as wood in living trees ensures general storage, defence, vascular and skeletal functions, we will ask general questions about synergies and trade-offs between posture control and other functions.
Botany 2014 : new frontiers in botany
Boise, United States

hal-01627031
https://hal.archives-ouvertes.fr/hal-01627031

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Evidence of anomalous volcanism is readily observed in the Gulf of Aden, although, much of this oceanic basin remains as yet unmapped. In this paper, we investigate the possible connection of the Afar hotspot with a major off-axis volcanic structure and its interpretation as a consequence of a the anomalous presence of melt by integrating several data sets, both published and unpublished, from the Encens-Sheba cruise, the Aden New Century (ANC) cruise and several other onshore and marine surveys. These include bathymetric, gravity, magnetic, magneto-telluric data, and rock samples. Based upon these observations, interpretations were made of seafloor morphology, gravity and magnetic models, seafloor age, geochemical analyses and tectonic setting. We discuss the possible existence of a regional melting anomaly in the Gulf of Aden area and of the probability of its connection to the Afar plume. Several models that might explain the anomalous volcanism are taken into account, such as a local melting anomaly unrelated to the Afar plume, an anomalously large volume of melt associated with seafloor spreading, and interaction of the ridge with the Afar plume. A local melting anomaly and atypical seafloor spreading prove inconsistent with our observations. Two previously proposed models of plume-ridge interactions are examined: the diffuse plume dispersion called pancaked flow and channelized along-axis flow. We conclude that the configuration and structure of this young ocean basin may have the effect of channeling material away from the Afar plume along the Aden and Sheba Ridges to produce the off-axis volcanism observed on the ridge flanks. This interpretation implies that the influence of the Afar hotspot may extend much farther eastwards into the Gulf of Aden than previously believed. The segmentation of the Gulf of Aden and the configuration of the Aden-Sheba system may provide a potential opportunity to study channeled flow of solid plume mantle from the plume along a segmented ridge and nearby continental margins.
ISSN: 0012-821X

hal-00486140
https://hal.archives-ouvertes.fr/hal-00486140
DOI : 10.1016/j.epsl.2010.02.036

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
We surveyed the junction between the central and southern Philippine Trench and the Sangihe Trench near 6øN using swath bathymetry, gravity, and magnetics. These data, along with seismicity, allow us to discuss the genetic relations between these trenches and the forces acting on converging plates. Our final model favors the northern extension of the Halmahera Arc up to 8øN, with three segments offset left-laterally along NW-SE transform faults. Accretion of the northern segment to Mindanao Island 4 to 5 m.y. ago resulted in the failure within the Philippine Sea Plate east of the arc. Initiation of the Philippine Trench between 7øN and 10øN agrees with the maximum recorded depth of the Philippine Trench floor (10,000 m below sea-level) and Philippine Sea slab (200 km). South of 6øN (trench junction), another segment of the arc is being subducted beneath the Sangihe margin, while south of 3øN, the southern segment of the Halmahera Arc is still active. The rapid southward shallowing of the trench floor along the southern Philippine Trench, the type of faulting affecting both sides of the trench, the lack of significant interplate seismicity, and the concentration of the seismicity beneath the Miangas-Talaud Ridge are interpreted as a slowing down of the subduction along this branch of the Philippine Trench compared with the rest of the subduction zone. The Sangihe deformation front has been recognized up to 7øN but seems active only south of 6øN.
ISSN: 2169-9275

hal-01261614
https://hal.archives-ouvertes.fr/hal-01261614
https://hal.archives-ouvertes.fr/hal-01261614/document
https://hal.archives-ouvertes.fr/hal-01261614/file/lallemandJGR1998.pdf

Éditeur(s) : HAL CCSD
Résumé : National audience
The Lesser Antilles subduction zone has produced no recent strong thrust earthquakes, making it difficult to quantify the seismic hazard from such events. The Lesser Antilles arc has a low subduction rate and an accretionary wedge that is very wide at its southern end. To investigate the effect of the wedge on seismogenesis, numerical models of forearc thermal structure were constructed along six transects perpendicular to the arc in order to determine the thermally predicted width of the seismogenic zone. The geometry of each section is constrained by published seismic profiles and crustal models derived from gravity and seismic data and by earthquake hypocenters at depth. A major constraint on the deep part of the model is that mantle temperature beneath the volcanic arc should achieve a temperature of 1,100°C to generate partial melts. Predicted surface heat flow is compared to the available heat flow observations. Thermal modeling results indicate a systematic southward increase in the width of the seismogenic zone, more than doubling in width from north to south and corresponding to a dramatic southward increase in forearc width (distance from the arc to the deformation front of the accretionary wedge). The minimum width of the seismogenic zone (distance between the intersections of the subduction interface with the 150°C and 350°C isotherms) increases from about 80 km, north of 16°N, to 230 km, at 13°N. The maximum width (between the 100°C and 450°C isotherms) ranges from about 150 km in the north to up to 320 km in the south. This large variation in the width of the seismogenic zone is a consequence of the increasing width of the accretionary wedge to the south, caused by the increased thickness of sediment on the subducting plate. There is good agreement between the thermally predicted seismogenic limits and the sparse distribution of recorded thrust earthquakes, which are observed only in the northern portion of the arc. Possible scenarios for mega-thrust earthquakes are discussed. Depending on the segment length (along-strike) of the rupture plane, the occurrence of an event of magnitude 8-9 cannot be excluded.
Bulletin Société Géologique de France

insu-00814056
https://hal-insu.archives-ouvertes.fr/insu-00814056
DOI : 10.2113/gssgfbull.184.1-2.47

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Deep-seated gravitational spreading (DSGS) affects the slopes of formerly glaciated mountain ridges. On Mars, DSGS has played a key role in shaping the landforms of the giant Valles Marineris troughs. Though less spectacular, DSGS is common in terrestrial orogens, where understanding its mechanics is critical in the light of the ongoing climate change because it is a potential source of catastrophic landslides in deglaciated valleys. We conducted parametric numerical studies in order to identify important factors responsible for DSGS initiation. DSGS models are computed using an elastoviscoplastic finite element code. Using ADELI's software, we reproduce topographic ridge spreading under the effect of valley unloading. Two types of spreading topographic ridges are investigated, homogeneous or with horizontal rheological layering. We find that gravitational instabilities are enhanced by high slopes, which increase gravitational stress, and low friction and cohesion, which decrease yield stress. In the unlayered ridge, instability is triggered by glacial unloading with plastic strain concentration inside the ridge and at the base of the high slopes. Vertical fractures develop in the upper part of the slope, potentially leading to fault scarps. Ridge homogeneity promotes a deformation mode controlled by uphill-facing normal faulting and basal bulging. In the second case, the ridge encompasses horizontal geological discontinuities that induce rock mass anisotropy. Discontinuity located at the base of the slope accumulates plastic strain, leading to the formation of a sliding plane evolving into a landslide. The presence of a weak layer at ridge base therefore promotes another slope deformation mode ending up with catastrophic failure. Mechanical conditions and slope height being equal, these conclusions can probably be extrapolated to Earth. Compared with Mars, DSGS on Earth is inhibited because terrestrial topographic gradients are lower than in Valles Marineris, an effect counterbalanced by increased gravitational stress, where the intensity of deformation is enhanced because of the Earth gravity potential.
ISSN: 0169-555X

hal-01420007
https://hal.archives-ouvertes.fr/hal-01420007
DOI : 10.1016/j.geomorph.2016.06.011

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The Eastern Rift System (ERS) of northern Tanzania and southern Kenya, where a cratonic lithosphere is in the early stages of rifting, offers an ideal venue for investigating the roles of magma and other fluids in such an environment. To illuminate these roles, we jointly invert arrival times of locally recorded P and S body waves, phase delays of ambient noise generated Rayleigh waves and Bouguer anomalies from gravity observations to generate a 3-D image of P and S wave speeds in the upper 25 km of the crust. While joint inversion of gravity and arrival times requires a relationship between density and wave speeds, the improvement in resolution obtained by the combination of these disparate data sets serves to further constrain models, and reduce uncertainties. The most significant features in the 3-D model are (1) P and S wave speeds that are 10–15 per cent lower beneath the rift zone than in the surrounding regions, (2) a relatively high wave speed tabular feature located along the western edge of the Natron and Manyara rifts, and (3) low (∼1.71) values of Vp/Vs throughout the upper crust, with the lowest ratios along the boundaries of the rift zones. The low P and S wave speeds at mid-crustal levels beneath the rift valley are an expected consequence of active volcanism, and the tabular, high-wave speed feature is interpreted to be an uplifted footwall at the western edge of the rift. Given the high levels of CO2 outgassing observed at the surface along border fault zones, and the sensitivity of Vp/Vs to pore-fluid compressibility, we infer that the low Vp/Vs values in and around the rift zone are caused by the volcanic plumbing in the upper crust being suffused by a gaseous CO2 froth on top of a deeper, crystalline mush. The repository for molten rock is likely located in the lower crust and upper mantle, where the Vp/Vs ratios are significantly higher.
ISSN: 0956-540X

hal-01622055
https://hal.archives-ouvertes.fr/hal-01622055
https://hal.archives-ouvertes.fr/hal-01622055/document
https://hal.archives-ouvertes.fr/hal-01622055/file/roeckerGJI2017.pdf
DOI : 10.1093/gji/ggx220

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Studies on tree biomechanical design usually focus on stem stiffness, resistance to breakage or uprooting, and elastic stability. Here we consider another biomechanical constraint related to the interaction between growth and gravity. Because stems are slender structures and are never perfectly symmetric, the increase in tree mass always causes bending movements. Given the current mechanical design of trees, integration of these movements over time would ultimately lead to a weeping habit unless some gravitropic correction occurs. This correction is achieved by asymmetric internal forces induced during the maturation of new wood. The long-term stability of a growing stem therefore depends on how the gravitropic correction that is generated by diameter growth balances the disturbance due to increasing self weight. General mechanical formulations based on beam theory are proposed to model these phenomena. The rates of disturbance and correction associated with a growth increment are deduced and expressed as a function of elementary traits of stem morphology, cross-section anatomy and wood properties. Evaluation of these traits using previously published data shows that the balance between the correction and the disturbance strongly depends on the efficiency of the gravitropic correction, which depends on the asymmetry of wood maturation strain, eccentric growth, and gradients in wood stiffness. By combining disturbance and correction rates, the gravitropic performance indicates the dynamics of stem bending during growth. It depends on stem biomechanical traits and dimensions. By analyzing dimensional effects, we show that the necessity for gravitropic correction might constrain stem allometric growth in the long-term. This constraint is compared to the requirement for elastic stability, showing that gravitropic performance limits the increase in height of tilted stem and branches. The performance of this function may thus limit the slenderness and lean of stems, and therefore the ability of the tree to capture light in a heterogeneous environment.
ISSN: 0022-5193

hal-00534316
https://hal.archives-ouvertes.fr/hal-00534316
DOI : 10.1016/j.jtbi.2008.10.011

Éditeur(s) : HAL CCSD
Résumé : International audience
BackgroundTree above ground biomass (AGB) is currently estimated by tree-level allometrical models that take into account, tree volume estimated from proxy variables of tree size (DBH) and species average wood specific gravity (WSG). These methods are common and realistic from a practical point of view. However, they do not take into account deviance from fixed allometrical trajectories and species or tree level WSG variations. Here, we present Xtrawood software that allows computation of tree AGB according to structure and WSG variations.MethodXtrawood reconstructs tree structure and integrates WSG variations by merging tree structure and WSG data measured at different position in trees, leading to the computation of global AGB and visualization of WSG variation along tree structure. Tree structure is measured according to stem dimensions (length, diameter) and positions within tree, and encoded in Multiscale Tree Graph format (MTG). WSG data is made of radial WSG profiles (1 measure each 0,5 cm from pith to bark) sampled at different heights within whole tree. Xtrawood output are illustrated using a dataset collected on an Amazonian forest ‘biomass dominant species’, Dicorynia guianensis Amsh., also known to exhibit substantial WSG gradients along both radial and vertical axis. 9 trees ranging from 15 to 60 cm DBH were measured by climbers. Each tree was felled and samples were collected at different positions (3 in trunk, 1 to 5 in crown) to record WSG radial profiles.ResultsXtrawood allows computation of tree volume, but also visualization of WSG variations in tree as well as inference of WSG radial profiles at different heights. Output variables are decomposed according to different tree scale and locations (axis, trunk/crown) and easy to extract. Xtrawood results will be compared to those of standard estimation method and can be used to identify positions in trees where WSG value leads to the better estimate of tree AGB.Conclusion/perspectiveXtrawood produces AGB estimate with data from intensive measurements practices. The sampling protocol, used here, remains destructive and time-consuming because Xtrawood is not directly dedicated to forest managers, but to help calibration of realistic sampling strategies. Moreover, Xtrawood offers a way to understand relationships between tree development, WSG variations within tree structure and biomass accumulation in the context of natural forests or plantations. A software demo is available at coffee break.
53rd Annual Meeting of the Association for Tropical Biology and Conservation (ATBC 2016)
Montpellier, France

Droits : http://creativecommons.org/licenses/by/
hal-01349613
https://hal.archives-ouvertes.fr/hal-01349613

Éditeur(s) : HAL CCSD
Résumé : Gravitropism is a major process in vertical growth as it allows the positioning of plant in the gravity field and thus, for trees, it takes part in the light foraging strategies. Without any gravitropism, trees would adopt a weeping habit or fall on the ground due to the increasing with growth supported weight, especially at the advance regeneration stage (sapling stage) in the understorey, where tree are very slender and poorly stiff. Most of the gravitropic studies are made by physiologists in order to understand the process and thus are associated to complex laboratory methods (genetic engineering, anatomical studies, accurate 2D ou 3D measurements of form changes with time). In order to study the ecological relevance and the specific diversity of gravitropic performances in natural forests, we developed a framework that uses different kinds of datas. Synchronical analysis has been done i) at the population level in large sample of trees and ii) at the tree level from destructive measurement of the dissymmetry maturation strains known to be the main motor of the posture control reaction of trees. In both cases, biomechanical models allows to estimate some aspects of the dynamic gravitropic process. Diachronical analysis has been done in natural conditions on permanent plots, or in a more traditional way, by observing in greenhouse experiments the righting movements of plants artificially tilted. In the first case, the problem is the high variability of natural disturbances and the slowness of growth and movements in the dark understorey. The second choice allows a measurement of a capacity (i.e. the ability of the species to react in quite extreme conditions of verticality disturbance but good for growth light and nutrient conditions) that is more easy to analyse, but is maybe not so relevant for estimating the ecological strategy (some species could have developed a high efficience of gravitropic reaction in natural conditions by avoiding the mechanical disturbance or adapting the reaction to slow growth and changing environments in natural conditions). All approaches use the same basic biomechanical modelling, i) to analyse simultaneously the reaction and the disturbance (due to the weight increase) during growth, or ii) to combine different parameters (geometry, growth, weight, maturation strains) involved in shape changes and posture control. They give a classification of the species according to their gravitropic performances. Results on 15 species are discussed, with relation to shade-tolerance or avoidance.
6th Plant Biomechanics Conference
Cayenne, France

hal-00565956
https://hal.archives-ouvertes.fr/hal-00565956

Résumé : L'importance des forêts tropicales dans le cycle du carbone à l'échelle planétaire est majeure, tant en terme de stock qu’en terme de flux de CO2. Plusieurs études mettent en évidence des changements au sein des forêts tropicales au cours des 20 dernières années, notamment des changements de la dynamique forestière et une augmentation de la biomasse aérienne. Les déterminants de ces variations sont aujourd’hui discutés et nous proposons ici d’apporter une contribution à ce débat. Les données utilisées dans ce travail proviennent du dispositif de suivi forestier à long terme de Paracou, Guyane Française, mis en place en 1984 et qui recouvre plus de 120 ha de forêt tropicale humide. Les données météorologiques proviennent de la tour à flux du dispositif, Guyaflux. Les mesures de diamètre proviennent de la base Guyafor pour les données annuelles et bisannuelles, et des mesures de 260 arbres à proximité de la tour à flux pour les mesures diamétriques intra-annuelles.Cette thèse se divise en deux grandes parties. La première concerne l’analyse de la biomasse du dispositif de suivi forestier de Paracou en Guyane et l’implication des changements de structure de cette forêt sur le bilan de carbone. Cette partie est constituée de deux points. (i) Quelles échelles temporelles et spatiales sont pertinentes pour analyser les composantes de structure (biomasse, aire basale et nombre de tiges) et de dynamique (croissance, recrutement et mortalité) des forêts tropicales afin de minimiser les effets d’échantillonnage ? Nous avons établi une méthodologie permettant de relier les intervalles de temps et la surface de mesure aux coefficients de variation de chacune des variables de structure et de dynamique de la forêt. (ii) Quels processus démographiques sont prépondérants dans l’explication des variations de biomasse et comment se redistribue la biomasse accumulée dans le système ? L’augmentation de la biomasse observée sur le dispositif de Paracou serait liée à la rareté des évènements de mortalité des gros arbres qui portent une part très importante de la biomasse.La deuxième partie de la thèse concerne l’analyse de l’effet du climat à moyen terme, inter et intra-annuel, et les effets directs du climat dans les changements de dynamique de la forêt. Cette partie se divise en 3 points. (i) Comment quantifier le stress hydrique en forêt tropicale humide ? Nous avons réalisé un modèle journalier de réserve en eau du sol pour les arbres en forêt tropicale. (ii) Quelles variables sont explicatives de la croissance des arbres en forêt guyanaise ? Nous avons montré que l’eau dans le sol est le facteur le plus explicatif du déterminisme climatique parmi un panel de variables climatiques. (iii) Quels traits fonctionnels sont prédicteurs de la réponse des arbres aux variations climatique ? Nous avons déterminé que des traits spécifiques, densité du bois et la hauteur maximale, ainsi que le diamètre de l'arbre au moment de la mesure, modulent la croissance des arbres en réponse au climat.
At a global scale tropical forest play a major role in term of carbon stock as well as in term of CO2 fluxes. Several studies have highlighted changes in tropical forest functioning during the last 20 years including a faster turnover and an increase of above ground biomass. The drivers of these changes are discussed and throughout this thesis we propose to contribute to this debate. We use the data from the Paracou experimental site in French Guiana established in 1984 on 120 hectares of moist tropical forest. Meteorological data come from the flux tower of the site, Guyaflux. We use annual and bisannual diameter measurements from the Guyafor database, and intra-annual diameter increments from the measurements of 260 trees near the flux tower.This thesis has two main parts. In the first part we present the biomass analysis of the Paracou permanent plots and the impact of structural changes in this forest on the carbon budget. The first part is constituted by two points. (i) Which temporal and spatial scale used to analyze the structure (biomass, basal area and stem density) and dynamics (tree growth, recruitment and mortality)components of tropical forest in order to minimized sample bias ? We establish a simple method to rely measurement interval between census and surface of measurement to the coefficient of variation of forests structure and dynamic components (ii) Which demographic process are involved in the explanation of biomass variation and how the biomass is distributed in the system ? The observed increase of biomass at Paracou could be link to the rarity of big trees mortality events. These big trees represent the larger part of the biomass. In the second part, we present the analysis of intra and inter-annual climate variation effects on forest dynamic changes. This part is divided in two points. (i) How to model drought stress in moist tropical forest ? We built a daily water balance model for tropical trees. (ii) Which climate variables explain the tree growth in guianian forests? We shown that soil water availability is the determinant factor of tree growth among a panel of climate variables. (iii) Which functional traits are involved in the tropical tree growth responses to climate? In this analysis, we determined that wood specific gravity, maximum tree height and tree diameter modulate the tree growth response to climate variations.

http://www.theses.fr/2011AGUY0481/document

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The Pyrenean peridotites (lherzolites) form numerous small bodies of subcontinental mantle, a few meters to 3 km across, exposed within the narrow north Pyrenean zone (NPZ) of Mesozoic sediments paralleling the north Pyrenean Fault. Recent studies have shown that mantle exhumation occurred along the future NPZ during the formation of the Albian-Cenomanian Pyrenean basins in relation with detachment tectonics. This paper reviews the geological setting of the Pyrenean lherzolite bodies and reports new detailed field data from key outcrops in the Bearn region. Only two types of geological settings have to be distinguished among the Pyrenean ultramafic bodies. In the first type (sedimented type or S type), the lherzolites occur as clasts of various sizes, ranging from millimetric grains to hectometric olistoliths, within monogenic or polymictic debris flow deposits of Cretaceous age, reworking Mesozoic sediments in dominant proportions as observed around the Lherz body. In the second type (tectonic type or T type), the mantle rocks form hectometric to kilometric slices associated with crustal tectonic lenses. Both crustal and mantle tectonic lenses are in turn systematically associated with large volumes of strongly deformed Triassic rocks and have fault contacts with units of deformed Jurassic and Lower Cretaceous sediments belonging to the cover of the NPZ. These deformed Mesozoic formations are not older that the Aptian-early Albian. They are unconformably overlain by the Albian-Cenomanian flysch formations and have experienced high temperature-low pressure mid-Cretaceous metamorphism at variable grades. Such a tectonic setting characterizes most of the lherzolite bodies exposed in the western Pyrenees. These geological data first provide evidence of detachment tectonics leading to manle exhumation and second emphasize the role of gravity sliding of the Mesozoic cover in the preorogenic evolution of the Pyrenean realm. In the light of such evidence, a simple model of basin development can be inferred, involving extreme thinning of the crust, and mantle uprising along a major detachment fault. We demonstrate coeval development of a crust-mantle detachment fault and generalized gravitational sliding of the Mesozoic cover along low-angle faults involving Triassic salt deposits as a tectonic sole. This model accounts for the basic characteristics of the precollisional rift evolution in the Pyrenean realm.
ISSN: 0278-7407

hal-00512818
https://hal.archives-ouvertes.fr/hal-00512818
DOI : 10.1029/2009TC002588

Résumé : The use of acoustical systems in various human activities in the ocean (industry, defence, science) raises the issue of their impact upon marine mammals populations. Several serious accidents linked to the use of naval sonars led the military, industrial and scientific communities to investigate the potential dangers of their own activity. This report aims at identifying the risks for the cetaceans linked to the use of acoustic and seismic systems currently used for oceanographic science. The analysis proposed here stays within the frame of bibliography synthesis and elementary modelling, and brings no new scientific elements on the topic. An overview of the status of cetacean populations is given first, with a summary of the possible acoustical threats. Risks are classified and described, insisting on the cases of massive stranding events. The present status of knowledge about auditory characteristics of cetaceans is summarised, and the definition of an objective threshold for acoustical risk is discussed ; the usually-admitted values are finally retained, despite of their evident limitations. The report presents also the emission characteristics of the various acoustic and seismic systems used in oceanographic, emphasising the ones operated by Ifremer; for the potentially harmful ones (according to the currently-used criteria) a model is proposed for the radiated acoustical intensity field, giving the extent of risk areas. This analysis concludes to the harmlessness of most systems, excepted heavy seismics and at a lesser degree low-frequency multibeam echosounders. Finally a variety of possible mitigation measures are presented and discussed; the regulations imposed by some countries are detailed. The report finally recommends both short-term measures aimed at limiting the potential risks, and longer-term actions for participating in the general effort of scientific and technological research in this field.
L'emploi des systèmes acoustiques dans les diverses activités humaines en milieu océanique (industrielles, de défense, scientifiques) pose le problème de leur impact sur les populations de mammifères marins. L'évidence de plusieurs événements graves liés à l'utilisation de sonars navals a amené les communautés militaires, industrielles et scientifiques à s'interroger sur les dangers potentiels de leurs propres activités. Le présent rapport tente de cerner les risques, pour les Cétacés, liés à l'emploi des systèmes acoustiques et sismiques couramment mis en oeuvre pour la recherche océanographique. L'analyse proposée ici reste à un niveau de synthèse bibliographique et de modélisation élémentaire, et n'offre pas d'éléments scientifiques nouveaux sur la question. On commence par donner un panorama de la situation des populations de cétacés et des agressions sonores qui les menacent. Les risques acoustiques sont répertoriés et décrits, en insistant sur les cas avérés d'échouages massifs. L'état actuel de connaissances sur les caractéristiques auditives des cétacés est résumé, et la définition d'un seuil objectif de risque acoustique est discutée ; on retient par défaut les valeurs de seuils généralement admises actuellement, en dépit de leurs limitations évidentes.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2007/rapport-2390.pdf
http://archimer.ifremer.fr/doc/00000/2390/

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD
Résumé : Taiwan is a young mountain belt, known as one of the most active area in the world. Since the beginning of the 20th century more than twenty _ Mw 7 earthquakes have struck the island. However, the occurrence of larger events (_Mw 8) is still a matter of debate. In this framework it is of key importance to obtain longer record in order to evaluate the occurrence of large past earthquakes. The sub-aqueous paleoseismology, based on the record of the sedimentary gravity deposits, appears as a serious alternative to approach this thematic and is a rapidly advancing field that has the potential to illuminate the long-term history of seismicity.The first part of this work was to investigate the present sedimentary systems off east Taiwan, essential to understand the morphosedimentary features, sedimentary facies and processes governing the evolution of the submarine slope, and the controlling factors of the recent sedimentation. Our results showed that the offshore slope east Taiwan is affected by a variety of sedimentary systems and processes, and that turbidity currents appear as the main erosional processes covering nearly 60% of the sedimentary record. Turbidity currents are generated by distinct controlling factors such as tectonic and climatic activity that enabled us to define twoend-members relative to turbidity currents initiation: Turbidity currents preconditioned by tectonic activity and triggered by earthquakes shaking and likely deposited into intra-slope basin and turbidity currents driven by climatic activity such as extreme floods or typhoons, generated in basin directly connected with onland rivers.The second part consisted to apply a paleoseismic approach, based on turbidites record, at two time-scales. First, we tested and validated the method by correlating turbidites deposits with instrumental earthquakes. Then, once calibrated we extended the time-series back in time. We dated the three most recent turbidites layers circa 2001 ± 3 AD, 1950 ± 5 AD and 1928 ± 10 AD. Using empirical relationship that link peakground acceleration, distance and magnitude to calibrate the seismic sources, we correlate these three turbidites with instrumental earthquakes: the Chengkong Earthquake 12/10/2003 (Mw 6.8), the 11/24/1951 Taitung Earthquake (Mw 7.1) and the 9/4/1935 Lutao Earthquake (Mw 7.0) respectively. Applying criteria to discriminating the different triggering mechanisms for turbidity current generation, we propose that earthquakes are the main triggering mechanisms. Dating and age modeling provided a part of the chronology of extreme events since the last 3000 years and allowed us to estimate return time for earthquakes Mw _ 6.8.This work represents a good starting-point for future investigations in order to better assess Holocene time series of extreme events.
La chaine de Taïwan représente l’une des zones les plus actives au monde. Depuis le début du XXe siècle, plus d’une vingtaine de séismes _Mw 7 ont affecté l’île. Cependant la probabilité d’occurrence de séismes plus importants (_Mw 8) est toujours matière à débat. Dans un tel contexte, il apparait donc important d’obtenir des enregistrements plus anciens pour évaluer l’occurrence de tels évènements. La paléosismologie marine, basée sur l’enregistrement des dépôts issus de la sédimentation gravitaire, apparait comme une alternative sérieuse afin d’illuminer l’histoire de la sismicité sur des périodes anciennes. Ce travail de thèse apporte de nouvelles contraintes sur l’histoire sismique au large, à l’est de Taïwan, au cours des derniers 3000 ans.La première partie de ce travail consiste à caractériser les systèmes sédimentaires récents. Cette étape fut essentielle pour la compréhension des processus, faciès sédimentaires et les facteurs de contrôle de la sédimentation qui régissent l’évolution de la pente sous-marine. Ces résultats ont montré que l’Est de Taïwan est caractérisé par une grande variabilité de processus et que les courants de turbidité dominent l’enregistrement sédimentaire.Les courants de turbidité sont générés par deux facteurs distincts : l’activité tectonique/sismique et l’activité climatique. La deuxième partie de ce travail est consacrée à l’approche paléosismique en utilisant les dépôts de turbidités comme marqueurs des paléoséismes. Pour ce faire, nous avons dans un premier temps testé et validé l’approche à l’échelle du siècle dernier. Ensuite une fois calibré, nous avons pu étendre les séries temporelles à l’échelle de l’Holocène. Nous avons daté les trois plus récents évènements turbiditiques autour de 2001 ± 3 AD, 1950 ± 5 AD et 1928 ± 10 AD. En utilisant des relations empiriques intégrant magnitude, distance et valeur du "peak ground acceleration", nous avons pu calibrer la source sismique et ainsi corréler ces trois turbidites à trois séismes instrumentaux : le séisme de Chengkong (12/10/2003) (Mw 6.8), le séisme de Taitung (11/24/1951) (Mw 7.1) et le séisme de Lutao (9/4/1935) (Mw 7.0). Au-delà du siècle dernier, les datations et modèles d’âges nous permettent d’établir une partie de la chronologie des évènements extrêmes sur une période de 3000 ans et d’estimer un temps de retour pour des évènements de l’ordre _Mw 7. Les résultats ont toutefois montré que ces temps de retour sont nettement supérieurs à ceux connus sur le siècle dernier, ce qui suggère que tous les séismes ne sont pas enregistrés par les dépôts sédimentaires marins. Ce travail de thèse a donc permis de montrer que les dépôts issus de la sédimentation évènementielle peuvent être considérés comme marqueurs de la sismicité et que cette approche peut constituer un outil complémentaire pour les études portant sur le risque sismique.
https://tel.archives-ouvertes.fr/tel-01661529

NNT : 2014MON20133
tel-01661529
https://tel.archives-ouvertes.fr/tel-01661529
https://tel.archives-ouvertes.fr/tel-01661529/document
https://tel.archives-ouvertes.fr/tel-01661529/file/55796_LEHU_2014_archivage_cor.pdf