Éditeur(s) : HAL CCSD
Résumé : Today, one of the main challenges in the oil industry is the exploitation of new resources in naturally fractured reservoirs often located in structurally complex areas such as plate boundaries, mountain ranges or near salt structures. While numerical models of rock deformation based on continuum mechanics are becoming industry standard in providing efficient means for modelling natural fractures in reservoirs, the knowledge of past perturbed stress fields, which is referred as the type (normal, wrench or reverse), orientation and magnitude of the regional or local tectonic stresses that needs to be applied as boundary condition in numerical simulations, is often unknown or approximated.The essence of this thesis is to improve the recovery of the paleostress field needed to constrain numerical simulations. I first described and discuss through a comprehensive mechanically-based multi-parametric study how far we can rely on the commonly used paleostress inversion methods based on fault slip data and the Wallace and Bott assumptions. I then compared this method with a new generation technique based on geomechanics using field observations. Since slip markers on faults are hardly observed in core or image log, I used observed natural fracture data as main drivers for the inversion of the paleostress using geomechanically-based method. I demonstrated, through various outcrop and subsurface examples, how this can efficiently be done. Finally, I aimed at addressing the problem of polyphase fracture data sets with unknown mechanical type (joints, faults, stylolites ...) and expanded the mechanical stress inversion to the separation of tectonic phases.
Aujourd'hui, l'un des principaux défis dans l'industrie pétrolière est l'exploitation de nouvelles ressources dans les réservoirs naturellement fracturés souvent situés dans des zones structurellement complexes tels que les frontières de plaques, les chaînes de montagnes ou les structures de proches des dômes de sel. Alors que les modèles numériques de déformation des roches basée sur la mécanique des milieux continus fournissant des moyens efficaces pour la modélisation de fractures naturelles dans les réservoirs, sont devenus la norme dans l'industrie, les paléo-contraintes régionales ou locales appliquées comme condition aux limites dans les simulations numériques, définies par le régime (normal, décrochant ou inverse), l'orientation, et la magnitude des contraintes tectoniques, sont souvent inconnues ou approximées.L'essence de cette thèse est d'améliorer la prédiction du champ de paléo-contrainte nécessaire pour contraindre les simulations numériques. J’ai décrit dans un premier temps à travers une étude comparative multi-paramétrique complète basée sur la mécanique, dans quelle mesure nous pouvions compter sur les méthodes d'inversion des paléo-contraintes basées sur les hypothèses de Wallace et Bott et les données de glissement sur les failles. J’ai ensuite comparé ces méthodes avec une technique d’inversion de nouvelle génération basée sur la géomécanique en utilisant les observations de terrain. Puisque les marqueurs de glissement sur les failles sont rarement observés le long du forage, j’ai utilisé l’inversion géomécanique des contraintes pour les données de fractures naturelles observées. J’ai alors démontré, l’efficacité de cette technique à travers divers exemples d'affleurements et de subsurface. Enfin, j’ai proposé une solution afin de résoudre le problème des données de fractures polyphasées à type cinématique inconnu (joints, failles, stylolites ...) et étendu l’inversion de contrainte basée sur la géomécanique à la séparation des phases tectoniques.
https://hal.archives-ouvertes.fr/tel-01324110

tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110/document
https://hal.archives-ouvertes.fr/tel-01324110/file/theselejri.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Fractures or discontinuities perpendicular to the least stress σ3 were generated in a synthetic rock analogue (granular, frictional, cohesive, and dilatant) material in axisymmetric extension tests. These fractures are of two types defined by the mean stress σ. When σ is very small, the fractures form through the mode I cracking at tensile σ3 equal to the material tensile strength. The fracture walls have smooth surfaces. At higher σ, these surfaces become rougher, with the topography features forming faint or delicate plumose patterns. The amplitude of the plumose topography increases with σ. The axial stress σ3 at fracturing reduces in magnitude and changes in sign with the σ increase. Thus σ3 orthogonal discontinuities can form at compressive σ3. SEM observations show that these discontinuities are deformation localization bands where the material is characterized by the heterogeneous decohesion and volume and porosity increase due to dilatancy. The band thickness is several grain sizes. At formation, the bands are not opened, so they are not mode I fractures. They become fractures with plumose fractography after the separation of the sample parts along the band. The formation mechanism of these discontinuities or fractures is not completely clear, but it is suggested that it represents a running constitutive instability in the form of dilatancy banding (with further σ increase the bands become inclined to σ1, i.e., shear). The similarity between the experimentally generated plumose surface fractures and natural joints is discussed, and it is suggested that they can be formed as propagating constitutive instabilities.
ISSN: 0148-0227

hal-00585846
https://hal.archives-ouvertes.fr/hal-00585846
DOI : 10.1029/2010JB008104

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
Recent mathematical calculations allow us to define set fracture intensity (I), i.e., the amount of rock mass affected by fracture sets, independently of the investigation mode. This parameter, characteristic of each rock mass, is of much interest to describe the mechanical response of the rock mass to external influences. The aim of this work is to apply these mathematical equations on one site using measurements of three distinct fracture sets: (1) on a plane surface, (2) along a scanline, and (3) using borehole imaging, in order to evaluate and explain variability in collected data. Even if the three types of measurements give differences on absolute intensity values, they still define similar trends, i.e., the order of the fracturing impact of joint sets is the same from the three measurement methods, irrespective of the fact that obtained values are quite different from one survey method to another. We discuss the possible origins of these biases.
ISSN: 1435-9529

hal-01121556
https://hal.archives-ouvertes.fr/hal-01121556
DOI : 10.1007/s10064-014-0572-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Both oedometric and plane-strain tests were performed with parallelepipedic samples made of synthetic granular, cohesive, frictional and dilatant rock analogue material GRAM2. For the first time parallel sets of fractures that have all the characteristics of natural joints were reproduced in the laboratory. The fractures are regularly spaced, normal to σ3, and have plumose morphology very similar to that of natural joints. These fractures can form at tensile stress σ3 much smaller in magnitude than the tensile strength of material and even at slightly compressive σ3. When mean stress σ exceeds a certain value, the fractures become oblique to σ1 (the obliquity increases with σ), forming networks of conjugate shear bands/fractures. These results of plane-strain experiments are in good agreement with those of better controlled conventional axisymmetric tests on a similar material in Chemenda et al. (2011b) and are closer to real geological situations. Both types of experiments are complementary. Their results lead to the conclusion that at least certain categories of natural fractures (including joints, and conjugate shear fractures/bands) were initiated as deformation localization bands. The band orientation is defined by the constitutive properties/parameters (notably the dilatancy factor) that are sensitive to σ.
ISSN: 0040-1951

hal-00795555
https://hal.archives-ouvertes.fr/hal-00795555
DOI : 10.1016/j.tecto.2011.11.021

Éditeur(s) : [S.l.] : L.G. Stahl
Siècle(s) traité(s) : 20
Droits : Domaine public
Provenance : Archives départementales de Guadeloupe
Permalien : http://www.manioc.org/patrimon/ADG18107
ADG18107

Éditeur(s) : Londres : T. Woolmer
Siècle(s) traité(s) : 19
Provenance : Archives départementales de Guadeloupe
Permalien : http://www.manioc.org/patrimon/ADG18190
ADG18190

Éditeur(s) : HAL CCSD Elsevier
Résumé : We present comparative field studies in folded areas (Southern France. Moroccan Western Atlas and Abruzzo, Italy) giving new insights into fracture distribution within folded rocks of the shallow brittle crust. We show that the curvature in folds formed in brittle mechanical units is usually accommodated by multiple "dip-domain boundaries" (appearing as curvature discontinuities at fold scale) corresponding to relatively narrow and dense fracture zones, striking parallel or slightly oblique to the fold axis. They separate "dip-domains" where curvature is absent or moderate. It is shown that the dip-domain boundaries (which are obvious in the case of kink folds or box-fold anticlines) are currently present as multiple subtle hinges even when the curvature appears continuous at first sight. The nature of dip-domain boundaries is studied, they often cut through the whole thickness of the mechanical units Their internal structure varies, and a non-exhaustive typology is proposed For each type, an interpretative kinematic scenario shows how the dip-domain boundaries could initiate and develop. We suggest two kinds of origins (1) they could correspond to the reactivation of inherited, along-strike fracture zones (opening-mode fracture concentrations such as big joints, fracture corridors. Inherited faults, etc), (2) they could be created as mechanical instabilities during the fold formation (syn-folding origin), in particular through small reverse faults. In both cases, early zones of weakness localize the dip-domain boundaries, and control the Increase in curvature in association with increasing fracture density within the boundary. Because they represent well-defined vertically and axially persistent sub-seismic fracture zones generally limited to the thickness of the folded unit, dip-domain boundaries could enhance the axial permeability of folded and fractured reservoirs.
ISSN: 0191-8141

hal-00512651
https://hal.archives-ouvertes.fr/hal-00512651
DOI : 10.1016/j.jsg.2010.03.002

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : Extension fractures of two types defined by the mean stress σ were generated in a synthetic rock analogue material. When σ is very small, the fractures are mode I cracks with smooth surfaces. At higher σ, these surfaces have plumose topography, with the amplitude increasing with σ. Both SEM observations and mechanical measurements show that fractures/discontinuities in the latter case are initiated as dilatancy localization bands. They form under tensile or slightly compressive normal stress and can be seen as running constitutive instabilities. The similarity between the plumose fractography of the experimental fractures and natural joints suggests similarity in the formation mechanism.
ISSN: 1631-0721

hal-00585886
https://hal.archives-ouvertes.fr/hal-00585886
DOI : 10.1016/j.crme.2011.01.002

Éditeur(s) : Paris : chez Lejay
Siècle(s) traité(s) : 18
Droits : Domaine public
Provenance : Communauté d'agglomération de La Rochelle. Médiathèque Michel-Crépeau
Permalien : http://www.manioc.org/patrimon/MMC16024-2
MMC16024-2

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : Experiments were conducted to assess the potential impact of fractured well-cement degradation on leakage rate. Permeability was monitored while CO2-enriched reservoir-equilibrated brine was flowed at constant rate through a single fracture in a class G cement core under conditions mimicking geologic sequestration environments (temperature 60 °C, pressure 10 MPa). The results demonstrate that, at least for the conditions used in the experiment, an initial leakage in a 42 μm aperture fracture (permeability = 1.5 × 10-10 m2) can be self-mitigated due to the decrease of the fracture hydraulic aperture after about 15 h. This decrease results from the development of continuous highly hydrated amorphous Si-rich alteration products at the edge of the fracture and the dense carbonation of the bulk cement that mitigate the penetration of the alteration front.
ISSN: 0013-936X

hal-00950088
https://hal.archives-ouvertes.fr/hal-00950088
DOI : 10.1021/es401317c

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029

Éditeur(s) : HAL CCSD Elsevier
Résumé : Deficient sealing in the well cement plugs and annulus due to mechanical fracturing is an important risk of CO2 leakage from the reservoir to others permeable layers and the surface. Such situation was reproduced at laboratory scale in order to determine the hydro-chemical control on the fracture permeability. Specifically, we investigated the effect of CO2 rich-brine flowing through fractured Portland cements at T = 60 °C and P = 10 MPa and variable flow rates. We showed that carbonation process is dominant and induces permeability decrease and leakage mitigation for extremely low flow rate whereas for high flow rate injection the permeability remains constant due to the precipitation of a low density secondary Si-rich phase which maintains the initial fracture aperture. At intermediate flow rate the hydraulic aperture can increase due to the densification of the material triggered by the net precipitation of low porosity calcite. These results emphasize that more complex behaviors than those considered from batch experiments may take place in the vicinity of flowing fractures. Specifically, the redissolution of the neoformed calcite as well as the development of amorphous phases, both controlled by the CO2-rich brine renewing rate in the fracture may prevent the healing fracture.
ISSN: 1750-5836

hal-00857555
https://hal.archives-ouvertes.fr/hal-00857555
DOI : 10.1016/j.ijggc.2013.04.002

Éditeur(s) : HAL CCSD Elsevier
Résumé : We investigate experimentally the alteration of fractured class-G cement flowed by CO2-rich brine. The experiment mimics a mechanically damaged rough-walled fractured cement annulus at temperature 60 °C and pressure 10 MPa. The experiment consists of flowing a reservoir-equilibrated brine mixed with CO2 (partial pressure of 2.3 MPa) through the fracture of average aperture 14 μm at constant flow rate (100 μL min−1). This flow rate corresponds to pressure gradient representative of an average in situ hydrodynamic condition. Results indicate an intense alteration of the cement with a large removal of mass at the scale of the sample. However, the fracture alteration patterns are triggered by the initial heterogeneity of the fracture aperture; the aperture of the low aperture zones tends to decrease due to calcite precipitation whereas preferential paths develop in the zones of higher aperture associated. Nevertheless, the expected large permeability increase triggered by the mass removal is mitigated by the precipitation of a low density Si-rich amorphous material. The alteration rate will decrease with time because of the increasing distance of diffusion between the fracture where the reactants are actively renewed by advection and the portlandite and C-S-H dissolution fronts. The different zones of reaction can be adequately modeled by a simple 1D diffusion-reaction model using published kinetics coefficients and extrapolation to larger times than the experiment time can be drawn. Altogether, and in addition to the previous studies of the alteration of fractured well cement annulus, this study shows that the leakage potential is strongly controlled by the initial distribution of the aperture along the fracture: low aperture zones will tend to self-heal while localized flow in connected high aperture paths will be perennial.
ISSN: 1750-5836

hal-01346006
https://hal.archives-ouvertes.fr/hal-01346006
DOI : 10.1016/j.ijggc.2016.01.032

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We investigate the deformation induced by water pressure variations in hydrologically active natural fractures, and recorded by tiltmeters and strainmeters. The deformation associated with a single fracture is derived using finite-element modelling (FEM). A range in fracture geometries is explored, first to highlight the sensitivity of each geometrical parameter to the deformation, and secondly to allow transfer to observation sites. Water level variations in the fracture are then derived from a hydrological model, driven by observed rainfall, and calibrated on fracture water flow measurements. The modelling results are explicitly applied to constrain the local hydrological contribution to observations with the 100-m-long hydrostatic tiltmeter installed at Sainte-Croix-aux-Mines (France). Our study shows that well-founded physical modelling of local hydrological effect allows a substantial correction of records in observatories.
ISSN: 0956-540X

hal-00708093
https://hal.archives-ouvertes.fr/hal-00708093
https://hal.archives-ouvertes.fr/hal-00708093/document
https://hal.archives-ouvertes.fr/hal-00708093/file/fracture_v72.pdf
BIBCODE : 2009GeoJI.178..667L

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Although magmatism may occur during the earliest stages of continental rifting, its role in strain accommodation remains weakly constrained by largely 2-D studies. We analyze seismicity data from a 13 month, 39-station broadband seismic array to determine the role of magma intrusion on state-of-stress and strain localization, and their along-strike variations. Precise earthquake locations using cluster analyses and a new 3-D velocity model reveal lower crustal earthquakes beneath the central basins and along projections of steep border faults that degas CO2. Seismicity forms several disks interpreted as sills at 6-10 km below a monogenetic cone field. The sills overlie a lower crustal magma chamber that may feed eruptions at Oldoinyo Lengai volcano. After determining a new ML scaling relation, we determine a b-value of 0.87±0.03. Focal mechanisms for 65 earthquakes, and 13 from a catalogue prior to our array reveal an along-axis stress rotation of ∼60° in the magmatically active zone. New and prior mechanisms show predominantly normal slip along steep nodal planes, with extension directions ∼N90°E north and south of an active volcanic chain consistent with geodetic data, and ∼N150°E in the volcanic chain. The stress rotation facilitates strain transfer from border fault systems, the locus of early-stage deformation, to the zone of magma intrusion in the central rift. Our seismic, structural, and geochemistry results indicate that frequent lower crustal earthquakes are promoted by elevated pore pressures from volatile degassing along border faults, and hydraulic fracture around the margins of magma bodies. Results indicate that earthquakes are largely driven by stress state around inflating magma bodies.
ISSN: 1525-2027

hal-01667198
https://hal.archives-ouvertes.fr/hal-01667198
DOI : 10.1002/2017GC007027

Éditeur(s) : HAL CCSD
Résumé : International audience
The deformation of natural systems in response to subsurface water storage and redistribution provides insightsinto the main water flow path within heterogeneous systems, including the role of faults or fractures. A longbaseline tiltmeter was installed in the low-noise underground laboratory of Rustrel (LSBB) to study the responseof the Fontaine de Vaucluse (FDV) karst hydrosystem to water cycle. Tilt data and piezometric levels recorded in aborehole close to the LSBB show a strong correlation with the discharge of the system observed at the FDV spring30 km away. Over several months, tilt data were recorded on three base lines, thus allowing, for the first time,to study the tilt gradient variation that appears homogeneous. Such information provides a significant constrainton hydrological processes leading to the measured deformation. Several deformation models were tested usingthe ADELI code to estimate the type of hydro-mechanical structure that could reproduce the measured tilt andits gradient. On one hand, models show that uniform loading at the surface produces a much smaller signal thanobserved on measured data. On the other hand, the deformation related to the filling of a fracture following aprecipitation event requires unrealistic fracture size. Finally, we found that a suitable hydro-mechanical modelcorresponds to the loading of numerous fractures at the interface between the saturated and unsaturated zones. Sucha configuration predicts a tilt distribution in agreement with observations. This study suggests that tilt networksinto a karst system should provide key observation for deciphering hydrological processes
Geophysical Research Abstracts
Vienne, Austria

insu-01308594
https://hal-insu.archives-ouvertes.fr/insu-01308594

Éditeur(s) : Paris : Hippolyte Souverain Editeur
Résumé : Une page tirée d'un autre livre est située derrière la première couverture. Il s'agit d'un dialogue d'une pièce de théâtre
Siècle(s) traité(s) : 19
Droits : Domaine public
Provenance : Fondation Clément
Permalien : http://www.manioc.org/patrimon/FCL18011
FCL18011

Éditeur(s) : HAL CCSD American Association for the Advancement of Science
Résumé : 6 pages
International audience
Large impacts provide a mechanism for resurfacing planets through mixing near-surface rocks with deeper material. Central peaks are formed from the dynamic uplift of rocks during crater formation. As crater size increases, central peaks transition to peak rings. Without samples, debate surrounds the mechanics of peak-ring formation and their depth of origin. Chicxulub is the only known impact structure on Earth with an unequivocal peak ring, but it is buried and only accessible through drilling. Expedition 364 sampled the Chicxulub peak ring, which we found was formed from uplifted, fractured, shocked, felsic basement rocks. The peak-ring rocks are cross-cut by dikes and shear zones and have an unusually low density and seismic velocity. Large impacts therefore generate vertical fluxes and increase porosity in planetary crust.
ISSN: 0036-8075

hal-01399386
https://hal.archives-ouvertes.fr/hal-01399386
PUBMED : 27856906
DOI : 10.1126/science.aah6561

Éditeur(s) : HAL CCSD
Résumé : This work focus on the characterization of the source and dynamic of compactional fluids during sedimentary burial, through two complementary examples of late orogenic oil‐field half‐grabens: The exhumed Lodève Permian Basin and a deep buried Jurassic basin in the North Viking Graben (North Sea).Constituting the main part of the thesis, a multi‐disciplinary approach was conducted in the Lodève Basin where Ba‐F‐Cu‐Pb polymetallic mineralized systems are trapped into synrift faults and paleokarsts in the carbonate basement at the hinge point of the rollover. The source, timing and P/T conditions of fluid migration were deduced from the analysis of the microfabric, the fluid inclusions microthermometry, and the isotopic (Sr, S, O, H) and Rare Earth Element (REE) signature. Results are then crossed with a structural and thermal modeling that consolidates the sequence and dynamics of fluid during burial.A similar approach was conducted in the North Viking Graben where fluid markers are restricted to 3D seismic and well core data. Comparable Ba‐Pb‐Zn veins are reported in basin margin, plugging one of the most important siliciclastic hydrocarbon reservoir in the substratum. This analysis provides additional constraints on basinal fluid behavior and allows us to propose a global dynamic model for various compositions of fluids and reservoirs.We conclude to a polyphase fluid sequence history including:(a) In the carbonate basement of the Lodève Basin, karstic paleocanyon incisions and associated cavities coupled to synrift fault, act as major drain for fluids. These structures are early affected by hypogen‐sulfuric karstification in response to the interaction between bacterial oxidation of sulfides entrapped within Lower Permian blackshales and the basement oxidizing aquifer.(b) Disequilibrium compaction initiates overpressure‐driven basinal fluid migration towards basin margins, characterized by temperatures around 150‐180°C and salinities between 9 et 18wt%eq.NaCl. Isotopic (Sr, S, O) and REE analyses reveal that Ba‐M+‐rich mineralizing fluids derived mainly from buried blackshales diagenesis. External fluids coming from the lower crust are also identified that play a key role in fluorite precipitation by the leaching of late hercynian granites (mean temperature of 250°C and salinity > 20wt%eq.NaCl).(c) During the synrift period, fluid overpressure is responsible for the periodic reactivation of fault plane according to seismic‐valve process, bedded‐control shearing and hydraulic brecciation at the basement‐seal interface. These mechanisms induce cyclic polymetallic mineralization by the mixing between in‐situ formation water and deep ascending basinal fluids.(d) Thermogenic fluids expulsion starts with last basinal fluids during late burial stage. Hydrocarbons thus migrate along the same regional pathways up to the rollover crest, where they are partly rerouted by the previous mineralized baffle.(e) In the Lodève basin, post‐rift exhumation of the margins led to the remobilization of synrift deposits by subaerial biochemical processes at the sulfate‐methane transition. The latter results from the interaction between the still active hydrocarbon dysmigration with a playa lake sulfate‐rich aquifer. Secondary low‐temperature barite fronts precipitate then within basement meteoric karsts.In addition to the « source to sink » model of basinal fluids, this work provides new insights on the early plugging of hydrocarbon reservoirs and for the metallogenesis of Mississippi Valley‐Type deposits.
Ce travail porte sur la caractérisation de la source et de la dynamique des fluides de bassin au cours de leur chargement à travers deux exemples complémentaires de demi‐grabens tardi‐orogéniques pétroliers : Le Bassin Permien de Lodève, aujourd’hui à l’affleurement et un bassin jurassique enfouis dans le North Viking Graben (Mer du Nord).Le coeur de la thèse concerne le Bassin de Lodève où, à partir d’une approche pluridisciplinaire intégrée, nous avons caractérisé l’architecture des minéralisations (Ba, F, Cu, Pb) piégées dans un réseau paléokarstique alimenté par les failles syn‐rift, dans le substratum carbonaté à l’apex du roll‐over. La source, le calendrier et les conditions de migration des fluides ont été approchés à partir de l’analyse de la micro‐fabrique, la microthermométrie sur inclusions fluides, les analyses isotopiques (Sr, S, O, H) et de Terres Rares. Les résultats analytiques ont été enfin croisés avec un modèle thermique et structural du bassin qui conforte la séquence et la dynamique du système fluide en cours d’enfouissement.Une démarche similaire, mais plus limitée, a été conduite dans le bassin du North Viking Graben où l’accès aux marqueurs fluides est restreint aux données de sismique 3D et de carottes. Comme à Lodève, les minéralisations Ba‐Pb‐Zn colmatent un réservoir dans le substratum à l’apex du roll‐over. Elles se présentent sous forme de ciments dans des grès ou des fractures. Cette analyse apporte des contraintes complémentaires et permet de proposer un modèle dynamique général avec des variantes en fonction de la nature des fluides et des réservoirs.On retiendra donc la séquence fluide suivante :(a) Dans le cas du bassin de Lodève sur substratum carbonaté, les chemins préférentiels de drainage se développent dans des paléocanyons N‐S couplés à un réseau de fractures et d’endokarsts météoriques. Ces derniers sont élargis en début de rifting par la dissolution hypogène sulfurique produite par l’oxydation bactérienne des sulfates et des pyrites des blackshales, au contact de l’aquifère oxydant du Cambrien.(b) Le déséquilibre de compaction initie la migration des fluides interstitiels en surpression vers les marges avec des températures autour de 150‐180°C et des salinités entre 9 et 18wt%eq.NaCl. Les analyses isotopiques (Sr, S, O) révèlent que la majorité des fluides provient de l’altération diagénétique des blackshales riches en métaux. Des interactions sont également mises en évidence avec des fluides profonds (entre 240°C et 260°C ; salinités > à 20wt%eq.NaCl), qui lessivent les granites tardi‐hercyniens.(c) Pendant le syn‐rift, les conditions de surpression de fluide permettent la réactivation cyclique des failles, les décollements stratigraphiques et la formation de brèches hydrauliques, favorisant la mise en connexion avec les réservoirs superficiels à l’apex du rollover. Le modèle de Sibson ajusté aux fluides de bassins est alors le moteur de la migration verticale.(d) Les fluides thermogéniques commencent à être expulsés avec les derniers fluides de compaction au cours d’un stade plus évolué de l’enfouissement en empruntant les mêmes chemins jusqu’à l’apex du roll over. Ils sont alors partiellement freinés et déviés par les colmatages minéralisés antérieurs.(e) A Lodève, la continentalisation des minéralisations antérieures au cours de l’exhumation post‐rift conduit à leur remaniement partiel au niveau de la transition sulfate‐méthane induite par l’interaction entre une playa évaporitique et la dysmigration des hydrocarbures. Des barytines secondaires de basse température, déprimées en Sr sont alors précipitées de manière synsédimentaire dans des karsts météoriques du socle.Outre l’illustration d’un modèle complet (source to sink) de dynamique des fluides dans un bassin, ce travail apporte de nouvelles contraintes dans l’approche du colmatage des réservoirs à hydrocarbures sur les têtes de blocs basculés et sur la genèse des gîtes miniers de type Mississippi Valley‐Type.
https://hal.archives-ouvertes.fr/tel-01457583

tel-01457583
https://hal.archives-ouvertes.fr/tel-01457583
https://hal.archives-ouvertes.fr/tel-01457583/document
https://hal.archives-ouvertes.fr/tel-01457583/file/th%C3%A8seLaurent2015V2.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Random walk (RW) or Continuous Time Random Walk (CTRW) are recurring Monte Carlo methods used to model convective and diffusive transport in complex heterogeneous media. Many applications can be found, including fluid mechanic, hydrology, and chemical reactors modeling. These methods are easy to implement, very versatile and flexible enough to become appealing for many applications because they generally overlook of deeply simplify the building of explicit complex meshes required by deterministic methods. RW and CTRW provide a good physical understanding of the interactions between the space scales of het-erogeneities and the transport phenomena under consideration. In addition, they can result in efficient up-scaling methods, especially in context of flow and transport in fractured media. In the present study, we review the applications of RW or CTRW for several situations coping with various spatial scales, and different insights into up-scaling applications. RW and CTRW advantages and downsides are also discussed, thus providing a few avenues for further works and applications.
ISSN: 0169-3913

hal-01449131
https://hal.archives-ouvertes.fr/hal-01449131
https://hal.archives-ouvertes.fr/hal-01449131/document
https://hal.archives-ouvertes.fr/hal-01449131/file/0025972-02.pdf
DOI : 10.1007/s11242-016-0693-z