Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wood has a hierarchical structure involving several levels of organisation. The stiffness of wood relies on its capacity to transfer mechanical stress to its stiffest element at the lowest scale, namely crystalline cellulose. This study aims at quantifying to what extend crystalline cellulose contributes to wood stiffness depending on its moisture content. The crystal strains of cellulose were measured using X-ray diffraction on wet and dry specimens of spruce, based on a previously published methodology. The comparison between crystal strain and macroscopic strain shows that, during elastic loading, cellulose strain is lower than macroscopic strain. The means ratio of crystal/macroscopic strain amounts 0.85 for dry specimens and 0.64 for wet specimens. This strain ratio cannot be explained just by the projection effect due to the difference in orientation between cellulose microfibrils and cell wall, but results from deformation mechanisms in series with cellulose. Analysis shows that this series contribution represents a non-negligible contribution to wood compliance and is strongly moisture-dependent. This contribution amounts 9% for dry specimens and 33% for wet specimens, corresponding to a 4-fold increase in compliance for the series contribution. The origin of these strains is ascribed to mechanisms involving bending or shear strain at different scales, due to the fact that reinforcing element are neither perfectly straight nor infinitely long.
ISSN: 0266-3538

hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031/document
https://hal.archives-ouvertes.fr/hal-01425031/file/Art_Almeras_al_Contribution_cellulose_moisture-dependent_elastic_behavior_2017.pdf
DOI : 10.1016/j.compscitech.2016.11.025

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Functional aspects of biodiversity were investigated in a lowland tropical rainforest in French Guyana (5°2'N, annual precipitation 2200 mm). We assessed leaf '15N as a presumptive indicator of symbiotic N2 fixation, and leaf and wood cellulose '13C as an indicator of leaf intrinsic water-use efficiency (CO2 assimilation rate/leaf conductance for water vapour) in dominant trees of 21 species selected for their representativeness in the forest cover, their ecological strategy (pioneers or late successional stage species, shade tolerance) or their potential ability for N2 fixation. Similar measurements were made in trees of native species growing in a nearby plantation after severe perturbation (clear cutting, mechanical soil disturbance). Bulk soil '15N was spatially quite uniform in the forest (range 3-5‰), whereas average leaf '15N ranged from m0.3‰ to 3.5‰ in the different species. Three species only, Diplotropis purpurea, Recordoxylon speciosum (Fabaceae), and Sclerolobium melinonii (Caesalpiniaceae), had root bacterial nodules, which was also associated with leaf N concentrations higher than 20 mg gm1. Although nodulated trees displayed significantly lower leaf '15N values than non-nodulated trees, leaf '15N did not prove a straightforward indicator of symbiotic fixation, since there was a clear overlap of '15N values for nodulated and non-nodulated species at the lower end of the '15N range. Perturbation did not markedly affect the difference '15Nsoil m '15Nleaf, and thus the isotopic data provide no evidence of an alteration in the different N acquisition patterns. Extremely large interspecific differences in sunlit leaf '13C were observed in the forest (average values from m31.4 to m26.7‰), corresponding to intrinsic water-use efficiencies (ratio CO2 assimilation rate/leaf conductance for water vapour) varying over a threefold range. Wood cellulose '13C was positively related to total leaf '13C, the former values being 2-3‰ higher than the latter ones. Leaf '13C was not related to leaf '15N at either intraspecific or interspecific levels. '13C of sunlit leaves was highest in shade hemitolerant emergent species and was lower in heliophilic, but also in shade-tolerant species. For a given species, leaf '13C did not differ between the pristine forest and the disturbed plantation conditions. Our results are not in accord with the concept of existence of functional types of species characterized by common suites of traits underlying niche differentiation; rather, they support the hypothesis that each trait leads to a separate grouping of species.
ISSN: 0029-8549

hal-01032378
https://hal.archives-ouvertes.fr/hal-01032378
DOI : 10.1007/s004420050593

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0

Éditeur(s) : Gauthier-Villars
Résumé : The analysis of humic compounds by elemental analysis, PY-GC-MS and HPLC techniques permitted determination of the origin of organic inputs, essentially terrestrial, and the effects of environmental conditions in the deposits along a north-south transect through the Rhone delta, from the river mouth to the open sea. In the prodelta the sedimentation of fine particles enriches the sediments in organic matter. The humic compound contents were relatively low in sediments, perhaps due to a rapid burying of organic matter which leads to anoxic conditions. In sediments fulvic acids are more abundant than humic acids. Elemental analysis indicated that fulvic acids were enriched in hydrogen and nitrogen as compared to humic acids. Furthermore, H/C and N/C ratios increased in the fulvic and humic acids towards the open sea, related to a more marine character. Pyrolysis analysis showed some differences between the chemical composition of fulvic acids which correspond to low molecular weights enriched in carbohydrates, and that of humic acids, high molecular weight compounds which are enriched in phenols and aromatic hydrocarbons. The pyrolysis-derived phenols were abundant near the river mouth, decreasing towards the open sea as nitrogen-containing-compounds increased. Near the river mouth, the abundance of phenolic aldehydes demonstrated by HPLC emphasized the existence of fresh organic matter. On the other hand, off the mouth, an increase in phenolic acids could indicate a more degraded organic material. The fractionation of humic acids in various classes of molecular weight species using ultrafiltration (Amicon membranes) and their analysis showed that, close to the river mouth, the large proportion of the high molecular weight humic compounds observed was enriched in phenols and carbohydrates, probably inherited from the terrestrial ligno-cellulosic complex. This process seemed to be superimposed on the increase of molecular weights which is usually observed as the environment becomes purely marine. These humic compounds would derived either from organic matter from terrestrial soils swept along by the river flow, after deposition on its bed or, more probably, from high molecular weight compounds which, associated with the mineral phase, flocculated when reaching the fluvio-marine front. Generally, the low molecular weight fractions were enriched in hydrogen and nitrogen. Near the river mouth, nitrogen-containing compounds were concentrated in the low molecular weight classes which correspond to organic molecules regarded as humic precursors. Off the mouth, they were incorporated into the high molecular weight complexes, certainly of marine origin.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1992 , Vol. 15 , N. 1 , P. 61-74

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00101/21187/18804.pdf
http://archimer.ifremer.fr/doc/00101/21187/

Éditeur(s) : HAL CCSD
Résumé : International audience
The hierarchical architecture of biopolymers induces remarkable behaviour. Wood mechanical properties mainly originate from the organization of wood tissue and interactions of cellwall components. The respective contribution on components inside those networks occurs at nanometric scale and still challenging to investigate in-situ. X-ray scattering techniques are now used as a routine technique to investigate internal organization of material components. For that purpose large-scale synchrotron facilities like ESRF offer leading X-ray sources capabilities (large energy range, high brilliance, high intensity, dedicated setups). ESRF's ID13 beamline serves high spacial resolution scanning setups to expertise in elastic scattering of monochromatic X-rays. Since analytical description of the scattering signal of cellulose have been well describe wood material benefit wide range of exposure conditions and sample environment. During this conference, we will present our achievements based on transverse sections of poplar specimens exposed to micrometric beam (1.2 μm side, 12.6 keV energy) to reveal crystalline cellulose distribution within wood tissue and to nanometric beam (100 nm side, 12 6 keV energy) to map the evolution of cellulose orientation within double cell wall over combined Wide-Angle (WAXS) and Small-Angle (SAXS) X-ray Scattering configuration. Within those setups hygrometric sample environment and stretching solicitations will be approached based on-going developments.
COST FP0802 Workshop 'Micro Characterisation of Wood Material'
Edimbourg, United Kingdom

hal-01113298
https://hal.archives-ouvertes.fr/hal-01113298

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Decomposition processes in tropical semi-evergreen forests are still poorly understood. The influence of soil properties and litter quality on decomposition rate was studied in two semi-evergreen forests of Guadeloupe, a forest plantation and a secondary forest, located on different soils. Leaf litter of four tree species was enclosed in litterbags for a 14-month period. Nonlinear correlations were calculated between mass loss and the concentration of major leaf components (soluble C, N, lignin, cellulose, tannins, total soluble phenols) in order to determine the best predictor of leaf litter decomposition. Soil physico-chemical properties and ratios between some of the above-mentioned litter quality parameters were also examined as mass loss predictors. In addition, non-linear correlations were calculated between mass loss and litter quality parameters, at successive periods. Litter quality was the main determinant of litter decomposition in the studied forests. Several litter quality parameters were correlated with leaf disappearance, varying according to stages of decomposition. Between 1 month and 2.5 months, the mass loss was correlated negatively with the initial phenol content and with initial lignin:N and (lignin+phenol):N ratios. From 2.5 to 5.5 months, the mass loss was correlated negatively with the initial phenol content and positively with the initial cellulose content. At later stages of decomposition (9-14 months), the mass loss was correlated negatively with the initial tannin content. Differences in soil characteristics and fauna did not seem to be enough to affect decomposition.
ISSN: 0178-2762

hal-00499535
https://hal.archives-ouvertes.fr/hal-00499535
https://hal.archives-ouvertes.fr/hal-00499535/document
https://hal.archives-ouvertes.fr/hal-00499535/file/Article_decomposition.pdf
DOI : 10.1007/s00374-002-0467-3

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Various bagasse fibre/cement composites have been prepared, the fibres having a random distribution in the composites. The influence of different parameters on the setting of the composite material has been studied: (1) botanical components of the fibre, (2) thermal or chemical treatment of the fibre, (3) bagasse fibre content and (4) added water percentage. This study shows a retarding effect of lignin on the setting of the composite, for small amount of heat-treated bagasse (200 °C) the behaviour of the composite is closely the same as the classical cement or cellulose/cement composite.
ISSN: 0958-9465

hal-00809715
https://hal.univ-antilles.fr/hal-00809715
DOI : 10.1016/S0958-9465(02)00003-3

Éditeur(s) : HAL CCSD Wiley
Résumé : 1. Resource control over abundance, structure and functional diversity of soil microbial communities is a key determinant of soil processes and related ecosystem functioning. Copiotrophic organisms tend to be found in environments which are rich in nutrients, particularly carbon, in contrast to oligotrophs, which survive in much lower carbon concentrations. We hypothesized that microbial biomass, activity and community structure in nutrient-poor soils of an Amazonian rain forest are limited by multiple elements in interaction. We tested this hypothesis with a fertilization experiment by adding C (as cellulose), N (as urea) and P (as phosphate) in all possible combinations to a total of 40 plots of an undisturbed tropical forest in French Guiana. After 2years of fertilization, we measured a 47% higher biomass, a 21% increase in substrate-induced respiration rate and a 5-fold higher rate of decomposition of cellulose paper discs of soil microbial communities that grew in P-fertilized plots compared to plots without P fertilization. These responses were amplified with a simultaneous C fertilization suggesting P and C colimitation of soil micro-organisms at our study site. Moreover, P fertilization modified microbial community structure (PLFAs) to a more copiotrophic bacterial community indicated by a significant decrease in the Gram-positive:Gram-negative ratio. The Fungi:Bacteria ratio increased in N fertilized plots, suggesting that fungi are relatively more limited by N than bacteria. Changes in microbial community structure did not affect rates of general processes such as glucose mineralization and cellulose paper decomposition. In contrast, community level physiological profiles under P fertilization combined with either C or N fertilization or both differed strongly from all other treatments, indicating functionally different microbial communities. While P appears to be the most critical from the three major elements we manipulated, the strongest effects were observed in combination with either supplementary C or N addition in support of multiple element control on soil microbial functioning and community structure. We conclude that the soil microbial community in the studied tropical rain forest and the processes it drives is finely tuned by the relative availability in C, N and P. Any shifts in the relative abundance of these key elements may affect spatial and temporal heterogeneity in microbial community structure, their associated functions and the dynamics of C and nutrients in tropical ecosystems.
ISSN: 0269-8463

hal-01204229
https://hal.archives-ouvertes.fr/hal-01204229
DOI : 10.1111/1365-2435.12329
PRODINRA : 311389

Éditeur(s) : HAL CCSD North Carolina State University
Résumé : Few studies have been conducted about relation between cellulose parameters and biomechanical properties of wood in tropical angiosperms species. For this purpose, on 13 trees from 3 species of French Guyana tropical rainforest in a clear active process of restoring verticality, i) growth strains were measured in situ in order to determine the occurrence of tension wood within samples and ii) cellulose structural parameters were estimated on all the samples using X-ray diffraction method. Crystallite size was estimated from the full-width at half-maximum of the Miller index (002) arc diffraction and angle T was measured following Cave's method. Relationships between these parameters and growth stresses were good and the variations between normal and tension wood were significant, i.e. a lower angle T and a larger crystallite size in tension wood. In order to have a good estimation of the microfibril angle in the main layer of the secondary wall for each species, an experimental calibration was done between angle T and microfibril angle observed with scanning electron microscopy.
ISSN: 19302126

hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799/document
https://hal.archives-ouvertes.fr/hal-01031799/file/42-575-1-PB.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
Tension wood, a tissue developed by angiosperm trees to actively recover their verticality, has long been defined by the presence of an unlignified cellulosic inner layer in the cell wall of fibres, called the G-layer. Although it was known that some species have no G-layer, the definition was appropriate since it enabled easy detection of tension wood zones using various staining techniques for either cellulose or lignin. For several years now, irrespective of its anatomical structure, tension wood has been defined by its high mechanical internal tensile stress. This definition enables screening of the diversity of cell walls in tension wood fibres. Recent results obtained in tropical species with tension wood with a delay in the lignification of the G-layer opened our eyes to the effective presence of large amounts of lignin in the G-layer of some species. This led us to review older literature mentioning the presence of lignin deposits in the G-layer and give them credit. Advances in the knowledge of tension wood fibres allow us to reconsider some previous classifications of the diversity in the organisation of the fibre walls of the tension wood.
ISSN: 0928-1541

hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686/document
https://hal.archives-ouvertes.fr/hal-01636686/file/2017_Ghislain-Clair_IAWAJ_DiversityOrganisationLignificationTensionWoodFibreWalls-AReview.pdf
DOI : 10.1163/22941932-20170170

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
Domestication can influence many functional traits in plants, from overall life-history and growth form to wood density and cell wall ultrastructure. Such changes can increase fitness of the domesticate in agricultural environments but may negatively affect survival in the wild. We studied effects of domestication on stem biomechanics in manioc by comparing domesticated and ancestral wild taxa from two different regions of greater Amazonia. We compared mechanical properties, tissue organisation and wood characteristics including microfibril angles in both wild and domesticated plants, each growing in two different habitats (forest or savannah) and varying in growth form (shrub or liana). Wild taxa grew as shrubs in open savannah but as lianas in overgrown and forested habitats. Growth form plasticity was retained in domesticated manioc. However, stems of the domesticate showed brittle failure. Wild plants differed in mechanical architecture between shrub and liana phenotypes, a difference that diminished between shrubs and lianas of the domesticate. Stems of wild plants were generally stiffer, failed at higher bending stresses and were less prone to brittle fracture compared with shrub and liana phenotypes of the domesticate. Biomechanical differences between stems of wild and domesticated plants were mainly due to changes in wood density and cellulose microfibril angle rather than changes in secondary growth or tissue geometry. Domestication did not significantly modify "large-scale" trait development or growth form plasticity, since both wild and domesticated manioc can develop as shrubs or lianas. However, "finer-scale" developmental traits crucial to mechanical stability and thus ecological success of the plant were significantly modified. This profoundly influenced the likelihood of brittle failure, particularly in long climbing stems, thereby also influencing the survival of the domesticate in natural situations vulnerable to mechanical perturbation. We discuss the different selective pressures that could explain evolutionary modifications of stem biomechanical properties under domestication in manioc.
PLoS ONE

halsde-00917926
https://hal.archives-ouvertes.fr/halsde-00917926
https://hal.archives-ouvertes.fr/halsde-00917926/document
DOI : 10.1371/journal.pone.0074727

Éditeur(s) : HAL CCSD Linnean Society of London
Résumé : International audience
The circumscription of Salicaceae has recently been enlarged to include a majority of the species formerly placed in the polyphyletic tropical family Flacourtiaceae. Several studies have reported a peculiar and infrequently formed multilayered structure of tension wood in four of the tropical genera. Tension wood is a tissue produced by trees to restore their vertical orientation, and most studies have focused on trees developing tension wood by means of cellulose-rich, gelatinous fibres, as is known in Populus L. and Salix L. (Salicaceae s.s.). This study aims to determine if the multilayered structure of tension wood is an anatomical characteristic common in other Salicaceae, and if so, how its distribution correlates to phylogenetic relationships. Therefore, we studied the tension wood of 14 genera of Salicaceae as well as two genera of Achariaceae, one genus of Goupiaceae, and one genus of Lacistemataceae, families closely related to Salicaceae or formerly placed in Flacourtiaceae. Opposite wood and tension wood were compared with light microscopy and 3D Laser Scanning Confocal Microscopy. The results indicate that a multilayered structure of tension wood is common in the family except in Salix, Populus, and one of their closest relatives, Idesia polycarpa Maxim. We suggest that tension wood may be a useful anatomical character in understanding phylogenetic relationships in Salicaceae. Further investigation is still needed on the tension wood of several other putatively close relatives of Salix and Populus, in particular Bennettiodendron Merr., Macrohasseltia L.O.Williams and Itoa Hemsl.
ISSN: 0024-4074

hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845/document
https://hal.archives-ouvertes.fr/hal-01392845/file/GhislainEtAl2016_MultylayerTWSalicaceae_Bot_Jsur the_Lin_Soc_HALssfig.pdf
DOI : 10.1111/boj.12471

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : A hypothetical mechanism for the generation of maturation stress in wood was tested experimentally. The hypothesis was that the maturation stress could partly originate in a physical mechanism related to daily changes in water pressure and associated diurnal strains. The matrix of lignin and hemicellulose, deposited in the cell wall during the night, would be put in compression by the effect of water tension during the next day. The cellulose framework, crystallizing during the day, would be put in tension by the decrease in tension at night and subsequent cell-wall swelling. This was tested on young saplings of sugi and beech. Half of the saplings were submitted to continuous lighting, which canceled diurnal strains. Saplings were tilted 40 degrees, and their uprighting movement was measured. The uprighting movement is directly due to the production of reaction wood and the concomitant development of large longitudinal maturation stress. It occurred in the continuously lighted plants at least as much as in control plants. We conclude that the generation of longitudinal maturation stress in tension or compression wood is not directly related to variations in water pressure and diurnal strains.
ISSN: 1435-0211

hal-01031891
https://hal.archives-ouvertes.fr/hal-01031891
DOI : 10.1007/s10086-005-0788-6

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : International audience
This work evaluates the influence of three different intensities of refinement of sisal pulp and the effect of accelerated aging cycles on the behavior of composites. Fiber-cements were prepared by the slurry de-watering method and pressing as a crude simulation of the Hatschek process. Mechanical behavior of composites was evaluated by four-point bending test at 28 days, and after 50 and 100 wet/dry cycles. Refinement of pulp and aging have increased the strength and bulk density of composites and decreased the toughness and porosity. The best mechanical performance after aging was achieved for samples with highly refined fibers.
ISSN: 1042-6914

hal-00809817
https://hal.univ-antilles.fr/hal-00809817
DOI : 10.1080/10426910601062065

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Tropical forests determine global biogeochemical cycles to a large extent, but control factors for key ecosystem processes such as decomposition remain poorly understood. With a full-factorial C (cellulose), N (urea), and P (phosphate) fertilization experiment, we tested the relative importance of C and nutrient limitation on litter decomposition in a mature lowland moist forest of French Guiana. Despite the previously demonstrated litter C quality control over decomposition and the very low soil P content (0.1 mg g(-1) of soil) at our study site, fertilization with C or P alone did not increase the decomposition of a wide range of litter types (N:P ratios between 20 and 80). Nitrogen fertilization alone also had no effect on decomposition. However, the combined fertilization with N and P resulted in up to 33.5% more initial litter mass lost, with an increasing effect with wider litter N:P ratios. Soil fauna strongly stimulated litter mass loss and enhanced nutrient fertilization effects. Moreover, nutrient effects on decomposition increased with additional C fertilization in the presence of fauna. Our results suggest that increased N availability is required for a positive P effect on decomposition in the studied P-poor tropical forest. Further stimulation of decomposition by C amendment through priming indicates energy limitation of decomposers that is co-determined by nutrient availability. The demonstrated intricate control of the key resources C, N, and P on decomposition calls for an intensified research effort on multiple resource limitation on key processes in tropical forests and how they change under multiple human impacts.
ISSN: 1432-9840

hal-01032414
https://hal.archives-ouvertes.fr/hal-01032414
DOI : 10.1007/s10021-012-9564-9