Éditeur(s) : Gauthier-Villars
Résumé : The suspended matter transported by the Orinoco to the Orinoco delta originates mainly in the Colombian Andes. The four clayey minerals (kaolinite, chlorite, illite and smectite) are always present in the deltaic suspensions, the delta deposits and the gulf of Paria. Illite contents are always dominant except in those regions of the gulf of Paria situated far from the mouths of the Orinoco tributaries characterized by smectites. In the delta, illite contents which are minimal during the dry season increase noticeably during the wet season which is marked by a high Liquid and particulate matter discharge. In the delta, the clay mineralogy of the substrate is comparable to that of dry season suspensions (February), thus showing a sedimentation composed of particulate matter carried by the Orinoco and Amazon rivers. In the wet season, the high liquid and particulate discharges circulate through the delta, then enter and disperse in the Caribbean Sea and the near Atlantic. The clay mineralogy described in the gulf of Paria show that this allochthonous participation of the Amazon in the deltaic sedimentation of the Orinoco is much more pronounced there. In this region, the spatial variations in illite content show this mineral to be a good marker for circulation.
Oceanolica Acta (0399-1784) (Gauthier-Villars), 1997 , Vol. 20 , N. 6 , P. 799-809

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00093/20435/18102.pdf
http://archimer.ifremer.fr/doc/00093/20435/

Éditeur(s) : Elsevier
Résumé : The Okinawa Trough is a natural laboratory for the study of later Quaternary land-ocean interaction and paleoenvironmental changes. In this study we reconstruct the evolution of clay mineral assemblages in Core DGKS9604 retrieved from the central Okinawa Trough. Illite dominates the clay mineral compositions, with average contents above 60%. Clay mineral evolution since 28 ka is closely related to changes in sediment provenance and paleoenvironment. Sea level rise and the strength of the Kuroshio Current control the dispersal and deposition of clays on the East China Sea shelf and in the Okinawa Trough, and thus, determine the clay mineral compositions in the core sediments. During the late last glacial period (28.0-14.0 ka), the paleo-Changjiang River mouth was situated at the shelf edge close to the central Okinawa Trough and thus, together with the outer shelf, supplied large volumes of terrigenous sediments directly into the trough. From 14.0 to 8.4 ka influence from the Changjiang decreased while the mid-outer shelf of the East China Sea became the dominant sediment source to the central Okinawa Trough as sea level rose and the Changjiang river mouth migrated west. Strong sediment reworking and erosion at the shelf edge at 15-13 ka significantly increased the lateral transport of fine-grained shelf sediments to the central Okinawa Trough. Since ca. 8.4 ka clays from Taiwan have dominated the sediment flux to the site, coinciding with the re-entry of the Kuroshio Current into the trough. The increasing influence of the Changjiang-sourced sediments since 1.5 ka was probably related to the weakening of the Kuroshio Current and/or a higher river flux. (C) 2010 Elsevier B.V. All rights reserved.
Palaeogeography, Palaeoclimatology, Palaeoecology (0031-0182) (Elsevier), 2010-03 , Vol. 288 , N. 1-4 , P. 108-117

Droits : 2010 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00002/11367/7977.pdf
DOI:10.1016/j.palaeo.2010.01.040
http://archimer.ifremer.fr/doc/00002/11367/

Éditeur(s) : HAL CCSD
Résumé : Thrusting fault zone in foreland basins are characterized by highly foliated zones generally enriched in phyllosilicates which can play a major role on the mechanical behaviour of the fault. In this context, investigations of synkinematic clay minerals permit to determine the origin of the fluid from which they precipitated as well as the mechanisms of deformation. Our study is focused on clay mineral assemblages (illite and chlorite) in a major thrust fault located in the Monte Perdido massif (southern Pyrenees), a shallow thrust that affects upper cretaceous-paleocene platform carbonates and lower Eocene marls and turbidites. It implied 3 km of displacement of the Monte Perdido thrust unit with respect to the underlying Gavarnie unit. In this area the cleavage development by pressure-solution is linked to the Monte Perdido and Gavarnie thrust activity. The core zone of the fault, about 6 m thick, consists of an interval of intensely deformed clay-bearing rocks bounded by major shear surfaces. The deformed sediment is markedly darker than the protolith. Calcite-quartz shear veins along the shear planes are abundant. Detailed SEM and TEM observations of highly deformed fault zone samples indicate that clay mineral enrichment in the core zone of the fault is not only related to passive increase by pressure-solution mechanism but that dissolution-recrystallization of phyllosilicates occurs during deformation. A mineral segregation is observed in the highly deformed zone. Newly formed 2M 1 muscovite is present along the cleavage whereas IIb chlorite crystals fill SV2 shear veins suggesting syntectonic growth of phyllosilicates in the presence of fluids in low-grade metamorphic conditions. These mineralogical reactions act as weakening processes and would favour Monte Perdido fault creeping.
Swiss Journal of Geosciences

hal-00795553
https://hal.archives-ouvertes.fr/hal-00795553
DOI : 10.1007/s00015-012-0098-0

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The chemical and isotopic compositions of clay minerals such as illite and chlorite are commonly used to quantify diagenetic and low-grade metamorphic conditions, an approach that is also used in the present study of the Monte Perdido thrust fault from the South Pyrenean fold-and-thrust belt. The Monte Perdido thrust fault is a shallow thrust juxtaposing upper Cretaceous-Paleocene platform carbonates and Lower Eocene marls and turbidites from the Jaca basin. The core zone of the fault, about 6 m thick, consists of intensely deformed clay-bearing rocks bounded by major shear surfaces. Illite and chlorite are the main hydrous minerals in the fault zone. Illite is oriented along cleavage planes while chlorite formed along shear veins (<50 μm in thickness). Authigenic chlorite provides essential information about the origin of fluids and their temperature. δ18O and δD values of newly formed chlorite support equilibration with sedimentary interstitial water, directly derived from the local hanging wall and footwall during deformation. Given the absence of large-scale fluid flow, the mineralization observed in the thrust faults records the P-T conditions of thrust activity. Temperatures of chlorite formation of about 240°C are obtained via two independent methods: chlorite compositional thermometers and oxygen isotope fractionation between cogenetic chlorite and quartz. Burial depth conditions of 7 km are determined for the Monte Perdido thrust reactivation, coupling calculated temperature and fluid inclusion isochores. The present study demonstrates that both isotopic and thermodynamic methods applied to clay minerals formed in thrust fault are useful to help constrain diagenetic and low-grade metamorphic conditions.
ISSN: 0010-7999

hal-00757736
https://hal.archives-ouvertes.fr/hal-00757736
DOI : 10.1007/s00410-011-0718-0

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : Results are reported for an acidic water flow-through experiment conducted in a fractured argillaceous limestone sample (73% carbonates). The change in fracture geometry and related parameters is reported for six data sets obtained from synchrotron X-ray microtomography experiments. High-resolution three-dimensional images of the sample allowed quantification of the changes in fracture morphology at a spatial resolution of 6 ;μm. Mineral mass loss and permeability changes in the sample were also determined. Several physico-chemical phenomena were identified during the experiment. Initial smooth fracture surfaces evolved rapidly toward rough surfaces with uneven clay coverage due to the preferential dissolution of carbonate minerals compared to clay minerals whose dissolution rate is about 106 slower. A microporous clay coating progressively developed at the fluid-rock interface during heterogeneous dissolution of the fracture, while the global dissolution rate of the fracture walls exponentially decreased. The increase in surface roughness and the presumed reorganization of clays caused a progressive reduction in permeability. During the last flow-through stage, a large decrease in sample permeability was attributed to the large removal of clay particles; this process was responsible for a dramatic collapse of the fracture walls near the sample inlet and led to the development of preferential flow pathways. The development of the clay coating also acted as a barrier to flow and mass transfer between calcite grains and bulk solution and affected transport processes within the fracture
ISSN: 0043-1397

hal-00405333
https://hal.archives-ouvertes.fr/hal-00405333
DOI : 10.1029/2006WR005379

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid–rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6–8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S–C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe–Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S–C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0.05 K0.86 (Al 1.77 Fe0.08 Mg0.15) (Si3.22 Al0.78) O10 (OH)2. They are enriched in Fe and Mg compared to the detrital micas. Newly-formed chlorites are associated with micas along the shear planes. According to microprobe analyses, they present the following structural formula: (Al1,48 Fe2,50 Mg1,84) (Si2,82 Al1,18) O10 (OH)8. All these data suggest that these clay minerals are synkinematic and registered the fault activity. In the gouge samples, illite and chlorite are the major clay minerals; smectite is locally present in some samples.In the foliated sandstones, Kubler Index (KI) ((001) XRD peak width at half height) data and thermodynamic calculations from synkinematic chlorite chemistry suggest that the main fault deformation occurred under temperatures around 220 °C (diagenesis to anchizone boundary). KI measured on pelites and sandstones from the hanging and footwall, display similar values coherent with the maximal burial temperature of the Annot sandstones in this area. The gouge samples have a higher KI index, which could be explained by a reactivation of the fault at lower temperatures during the exhumation of the Annot sandstones formation
ISSN: 0191-8141

hal-01172423
https://hal.archives-ouvertes.fr/hal-01172423
DOI : 10.1016/j.jsg.2015.03.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We analyzed twelve fault gouge samples from the Bogd fault in south-western Mongolia to understand the origin and behavior of clay minerals. The investigation relies on x-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high energy synchrotron x-ray diffraction methods to investigate microstructure and preferred orientation. Smectite (montmorillonite), illite-smectite mixed layers, illite-mica and kaolinite are the major clay components, in addition to quartz and feldspars, which are present in all samples. The observations suggest that the protoliths and the fault rocks were highly altered by fluids. The fluid-rock interactions allow clay minerals to form, as well as alter feldspars to precipitate kaolinite and montmorillonite. Thus, newly formed clay minerals are heterogeneously distributed in the fault zone. The decrease of montmorillonite component of some of the highly deformed samples also suggests that dehydration processes during deformation were leading to illite precipitation. Based on synchrotron x-ray diffraction data, the degree of preferred orientation of constituent clay minerals is weak, with maxima for (001) ranging from 1.3 to 2.6 multiples of a random distribution (m.r.d). Co-existing quartz and feldspars have random orientation distributions. Microstructure and texture observations of the gouges from the foliated microscopic zone, alternating with micrometric isotropic clay-rich area, also indicate that the Bogd fault experienced brittle and ductile deformation episodes. The clay minerals may contribute to a slip weakening behavior of the fault.
ISSN: 0191-8141

insu-00667194
https://hal-insu.archives-ouvertes.fr/insu-00667194
DOI : 10.1016/j.jsg.2011.10.006

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
PurposeMarine mangrove sediments in the Manche-à-Eau lagoon (Guadeloupe, Caribbean Sea) harbor locally extensive, white microbial mats. These mats cover the surface of reduced sediments near the roots of red mangrove trees, Rhizophora mangle, and are mainly composed of sulfur-oxidizing bacteria belonging to the Beggiatoaceae family, with some filamentous cyanobacteria. The goal of this study was to investigate the possible influence of sediment characteristics on the presence of these microbial mats.Materials and methodsFour push cores were collected in April 2013, two from zones with microbial mats and two from zones without mats. Sediment characteristics (grain-size distribution, mineralogy, total organic carbon (TOC) and total nitrogen (TN) contents, atomic TOC/TN ratios, and organic matter (OM) δ13C values) were compared for all four cores.Results and discussionSignificant differences were observed between sediments below microbial mats and those without mats. Sediments with microbial mats contained greater amounts of clay, and higher TOC, TN, and TOC/TN ratios, with lower total carbonate content and δ13C values. The higher clay content most likely results from lower fluid flow velocity near to mangrove roots, while higher TOC/TN ratios and lower δ13C values indicate higher inputs of OM from mangrove trees. These results are consistent with the fact that microbial mats were observed near the roots of mangrove trees, which trap OM from terrestrial vegetation and fine sediments.ConclusionsThe grain-size distribution of sediment particles, the total carbonate content, and the δ13C values are the main parameters discriminating between zones with microbial mats and those without mats. Variations in total carbonate content, which is mainly of biogenic origin, result from conditions that are more favorable for benthic organisms in zones without microbial mats. Variations of the TOC/TN ratios are controlled by the presence of a non-negligible amount of inorganic nitrogen bound to surface clay mineral particles and/or by microbial processes.
ISSN: 1439-0108

hal-01545903
https://hal.archives-ouvertes.fr/hal-01545903
DOI : 10.1007/s11368-016-1555-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The paleostorm history of coastal lagoon environments (Pierre Blanche Lagoon, central part of the Gulf of Lions) has been established by integrating clay mineralogy and geochemical analysis. Clay mineralogy combined with bulk major and trace elements concentrations allow for the definition of four different end members: the Mosson drainage basin, the sandy barrier, the biogenic and the anthropic components. The two main sedimentary sources of the lagoonal system are the Mosson drainage basin which has a high concentration of smectite and Al2O3, and the sandy barrier characterized by high contents of illite, chlorite, SiO2 and Zr. Smectite/(illite + chlorite), SiO2/Al2O3 and Zr/Al2O3 ratios can be used to reconstruct the past storm history of the Pierre Blanche Lagoon. Our results indicate that the sensitivities of the clay mineralogy and geochemistry proxies are different. These sensitivities could be related: 1) first, to the comparison between different grain size for geochemistry and for clay mineralogy: 2) second, to the complexity of the mix (four end-members for the geochemistry and two end-members for the clay minerals): and 3) third, by the storm's ability to transport sediment of different sizes. (C) 2010 Elsevier B.V. All rights reserved.
ISSN: 0037-0738

hal-00512614
https://hal.archives-ouvertes.fr/hal-00512614
DOI : 10.1016/j.sedgeo.2010.04.012

Éditeur(s) : Gauthier-Villars
Résumé : Marine muds deposited on the French Guiana coast mostly originate in the Amazon. Recent sediments are composed of (a) illite (33 %) and chlorite (13 %) of Andean mountain origin; and (b) kaolinite (28 %) and smectite (26 %), principally from the Amazonian lowlands but also from the Guiana Shield. In the coastal mud prism, high-resolution seismic profiles, together with sedimentological, micropaleontological and soil engineering studies, supplemented by C-14 dates, permitted a stratigraphic interpretation of eight cores. Three episodes have been determined on the basis of clay-mineral variations related to Amazonian lowland, Andean and Guiana shield sources. The older episodes 3 (3000-1700 y BP) and 2 (1700-1000 y BP) are predominantly characterized by lowland-derived clays (smectite = 43 %, kaolinite = 26 %) from Amazonian and local sources. The most important event is a reduction of the Andean source, due to successive dry phases which occurred in western Amazonia about 2200 and 1200 y BP, confirming that regional decreases in rainfall, water discharge and erosion were associated with climatic fluctuations. It is suggested that these dry phases (within the last 3000 years) are the consequence of several protracted (10-100 years) periods, during which atmospheric conditions mimicked the present-day ''El Nino Southern Oscillation'' (ENSO) phenomenon. As a result, particulate flux from the ocean decreased, leading to reduced silting of the Guiana coast, In the past 1000 years (episode 1), illite and chlorite have increased, indicating a stronger Andean contribution to the Amazonian continental flux that reaches the ocean. This is the first demonstration that the nature of the coastal marine muds of northern South America reflects climatic changes in the Amazon basin.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1996 , Vol. 19 , N. 5 , P. 477-487

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00094/20506/18175.pdf
http://archimer.ifremer.fr/doc/00094/20506/

Éditeur(s) : Elsevier Science Bv
Résumé : Although Ni isotopes have been shown to be significantly fractionated in terrestrial samples, their use in continental environmental studies has not yet been evaluated. The present study focuses on an ultramafic (UM) massif (Barro Alto, Goias, Brazil) because such areas are naturally rich in Ni. We present developed lateritic weathering profiles. The goal of the study is to evaluate the potential of using Ni isotopes in environmental continental studies by combining its isotopic signature with mineralogy, in order to better understand the geochemical cycling of Ni in UM settings during weathering. As such, Ni isotope values were measured in samples from the Barro Alto UM complex in the main stages of the lateritic weathering profile of UM rocks, including bedrock, ores (saprolitic and lateritic samples) and soil. The mineralogical composition of the samples, with a focus on the different Ni-bearing minerals, was also determined to decipher the potential links between isotopic fractionation and weathering dynamics. Isotopic signatures (δ60Ni) from the natural Ni geochemical cycle include: bedrock samples (δ60Ni = 0.28 ± 0.08‰), ore samples (saprolitic and lateritic, δ60Ni from -0.60 to 0.30‰) and soil samples (δ60Ni from -0.19 to -0.02‰). An overall trend of heavier isotope depletion was observed in the solid phase during weathering (Δ60NiSoil-Bedrock = -0.47‰). The mineralogical results were consistent with the literature and showed that the mineralogy of the lateritic part and soil was dominated by Fe-oxides, whereas clay minerals were the primary Ni phase scavengers in the saprolitic part of the profile. Thus, the formation of Ni-bearing clay minerals and Fe-oxides appeared to lead to depletion in heavier isotopes, which indicates preferential export of heavy isotopes in the dissolved phase. This result is consistent with isotopic signatures measured in the exchangeable pool of the solid phase (Δ60Niexch-total up to 0.47‰), and Ni isotopes appear to be a promising tracer to better understand the biogeochemical Ni cycling on the Earth’s surface.
Chemical Geology (0009-2541) (Elsevier Science Bv), 2015-05 , Vol. 402 , P. 68-76

Droits : 2015 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00254/36553/35098.pdf
DOI:10.1016/j.chemgeo.2015.02.039
http://archimer.ifremer.fr/doc/00254/36553/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Underground CO2 sequestration is highly recommended as an effective means of significantly decreasing CO2 concentration in the atmosphere. Mineral storage is the more secure technology, but requires the presence of high concentration of divalent cations in the pore-fluid. Results from CO2 percolation experiments through chlorite/zeolite-rich sandstone samples from the Pretty Hill Formation (Otway Basin, Australia) are presented. The dissolution of the laumontite (7 wt.%) and chamosite (7 wt.%) are the potential sources of calcium, iron and magnesium required for carbonate precipitation. The percolation experiment was setup to reproduce, at laboratory scale, the in situ temperature and pressure conditions (T = 95 degrees C and P = 10 MPa). The fluid injected at constant flow rate is a rock-equilibrated brine subsequently enriched in CO2 up to partial pressure of 6 MPa. We observe feldspars, laumontite and chamosite dissolution, kaolinite and silica precipitation and a noticeable sink of CO2 in the sample which is attributed to the precipitation of both amorphous carbon due to the reduction of CO2 and Fe-rich carbonate. Permeability decreases of about one order of magnitude due to the localization of the kaolinite precipitation in the main flow paths, while porosity increases. The high reactivity of this sandstone makes this reservoir a valuable target for CO2 mineralization, but the associated permeability decrease may limit the injection rate and the spreading of the CO2 in the reservoir.
ISSN: 0009-2541

hal-00712829
https://hal.archives-ouvertes.fr/hal-00712829
DOI : 10.1016/j.chemgeo.2011.11.018

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The thermal evolution of sediments in the shallowest part of sedimentary basins is challenging to investigate as most of the geothermometers are at their application limits. This is typically the case of the Callovian-Oxfordian claystones at the eastern border of the Paris Basin. A recent 2000 m deep well penetrated the entire Jurassic and Triassic sedimentary series and permitted coring of sediments never reached by previous drilling in this part of the basin. Thanks to the use of several independent geothermometers (apatite fission track thermochronology, fluid inclusion microthermometry, clay mineralogy and sedimentary organic matter evolution) the burial history of the Mesozoic series has been reconstructed, modeled and calibrated using kinetic algorithms relevant to the various paleothermometers used. In addition to these conventional methods, an innovative approach was developed using the temperature-dependence of the magnetic mineral assemblage within clay-rich sediments ("MagEval"). Thermal modeling indicates that the Callovian-Oxfordian and the Lower Triassic experienced maximum burial temperatures of 50 +/- 5 C-circle and 90 +/- 10 C-circle respectively, i.e., about 25 C higher than present-day. This temperature offset implies the erosion of several hundred meters of sediments which, depending on the thermal flux and conductivity considered, most likely constituted Upper Cretaceous chalk deposits. Falling sea level resulted in the exposure and subsequent dismantling of the chalk cover at the beginning of Cenozoic times. The eastern border of the basin was then subjected to slow erosion and discrete tectonic deformation.
ISSN: 0264-8172

hal-01313142
https://hal.archives-ouvertes.fr/hal-01313142
DOI : 10.1016/j.marpetgeo.2013.08.019

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Purpose: Marine mangrove sediments in the Manche-à-Eau lagoon (Guadeloupe, Caribbean Sea) harbor locally extensive, white microbial mats. These mats cover the surface of reduced sediments near the roots of red mangrove trees, Rhizophora mangle, and are mainly composed of sulfur-oxidizing bacteria belonging to the Beggiatoaceae family, with some filamentous cyanobacteria. The goal of this study was to investigatethe possible influence of sediment characteristics on the presence of these microbial mats. Materials and methods: Four push cores were collected in April 2013, two from zones with microbial mats and two from zones without mats. Sediment characteristics (grain-size distribution, mineralogy, total organic carbon (TOC) and total nitrogen (TN) contents, atomic TOC/TN ratios, and organic matter (OM) δ13C values) were compared for all four cores.Results and discussion: Significant differences were observed between sediments below microbial mats and those without mats. Sediments with microbial mats contained greater amounts of clay, and higher TOC, TN, and TOC/TN ratios, with lower total carbonate content andδ13C values. The higher clay content most likely results from lower fluid flow velocity near to mangrove roots, while higher TOC/TN ratiosand lower δ13C values indicate higher inputs of OM from mangrove trees. These results are consistent with the fact that microbial mats were observed near the roots of mangrove trees, which trap OM from terrestrial vegetation and fine sediments.Conclusions: The grain-size distribution of sediment particles, the total carbonate content, and the δ13C values are the main parameters discriminating between zones with microbial mats and those without mats. Variations in total carbonate content, which is mainly of biogenic origin, result from conditions that are more favorable for benthic organisms in zones without microbial mats. Variations of the TOC/TN ratios are controlled by the presence of a non-negligible amount of inorganic nitrogen bound to surface clay mineral particles and/or by microbial processes.
ISSN: 1439-0108

hal-01682110
https://hal.univ-antilles.fr/hal-01682110
DOI : 10.1007/s11368-016-1555-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In fold-and-thrust belts, shortening is mainly accommodated by thrust faults which are preferential zones for recrystallisation and mass transfer. This study focuses on a detachment fault related to the emplacement of the Monte Perdido thrust unit in the southern Pyrenees. The studied fault zone consists of a 10 m thick intensively foliated phyllonite developed within the Millaris marls, of Eocene age. The lithological homogeneity of the hanging wall and footwall allows us to compare the Millaris marls outside the fault zone with the highly deformed marls located in the fault zone and to quantify the chemical, mineralogical and volumetric changes related to deformation processes along the fault. The Millaris marls are composed of detrital quartz, illite, chlorite, minor albite and pyrite, in a micritic calcite matrix. In the fault zone, the cleavage planes are marked by clay minerals and calcite ± chlorite veins attest to fluid-mineral interactions during deformation. The mineral proportions in all samples from both the fault zone and Millaris marls have been quantified by two methods: (1) X-ray diffraction and Rietveld refinement, and (2) bulk chemical analyses as well as microprobe analyses to calculate modal composition. The excellent agreement between the results of these two methods allows us to estimate mineralogical variations using a modification of the Gresens' equation. During fault activation, up to 45 wt% of calcite was lost while the amounts of quartz and chlorite remained unchanged. Illite content remained constant to slightly enriched. The mineralogical variations were coupled with a significant volume loss (up to 45%) mostly due to the dissolution of micritic calcite grains. Deformation was accompanied by pressure solution and phyllosilicates recrystallisation. These processes accommodated slip along the fault. They required fluids as catalyst, but they did not necessitate major chemical transfers.
ISSN: 0264-8172

hal-00976361
https://hal.archives-ouvertes.fr/hal-00976361
DOI : 10.1016/j.marpetgeo.2013.12.016

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study presents the geochemical composition of superficial sediment under oxic and suboxic bottom water conditions along the Chilean continental margin (SE Pacific), where evidence for benthic chemosynthetic activity associated with diffuse seeping of chemically reduced fluids has been reported. The exploration was carried out at: (1) the Chilean Triple Junction (CTJ), at a water depth of ∼2900 m, with the additional indication of hydrothermal activity near a methane-rich cold-seep area (46°S) (German et al., 2010); and (2) the El Quisco methane seep site (EQSS), at ∼340 m water depth (33°S) (Melo et al., 2007; Krylova et al., 2014). While the deeper CTJ is located within an oxic environment (dissolved oxygen in the bottom waters: 164 μM), the shallower EQSS lies within a suboxic environment (dissolved oxygen in bottom water: 23 μM), located within the lower limit of the SE Pacific oxygen minimum zone (OMZ).Pore water from short cores was analyzed for dissolved major, minor, and trace elements (Cl, Na, Mg, K, Ca, Sr, Si, B, P, Ba, Pb, Mn, Fe, Cd, U, and Mo), δ13DIC, sulfide, sulfate, and methane. The solid sediment fraction was likewise analyzed for total organic carbon (TOC), metals, and redox potential. Elevated sediment temperatures were found in superficial sediments (5–13 °C) at the CTJ site, which could be due to warm fluids associated with the proximity of the ridge, where hydrothermal vents may occur. Reduced fluids were also present here, indicated by higher Mn fluxes toward the water column even in oxidized sediments (RPD > 8 cm), which contrasted with the lower fluxes in reduced sediments of the EQSS site (RPD ∼ 2 cm). 13C-depleted DIC, anomalously low pore water Cl (∼15 ppb), and low concentrations of other major elements may be the result of dilution by fluid seeping and precipitation of major elements, producing authigenic enrichment (Ca, Mg, Sr). The fluid could also: (a) be diluted by pure water produced during methane hydrate dissociation, as observed in other cold-seep areas; and (b) correspond to clay mineral dehydration, as reported in plate subduction systems. The reducing conditions established at the CTJ conduct the Cd enrichment at a similar magnitude of that seen at the shallower suboxic site (EQSS). Evidence of chimney or vent fauna was not observed. At the EQSS, higher TOC and total sulfide contents were consistent with enhanced deposition of organic matter and reducing conditions developed in the OMZ, favoring the authigenic enrichment of Cd, U and Pb. The geochemical evidence, based only on methane concentrations and δ13DIC, is insufficient to establish the presence of methane seeps, as previously reported.
ISSN: 0079-6611

hal-01412700
https://hal.archives-ouvertes.fr/hal-01412700
DOI : 10.1016/j.pocean.2016.09.002

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Heletz sandstone (Israel) reactivity is studied by means of CO2-rich brine percolation experiments and modeling. Experiments are performed at in situ temperature and pressure conditions with two distinctly different injection flow rates and for two different brine compositions: the genuine Heletz brine and a similar brine but in equilibrium with gypsum. The Heletz sandstone is composed of quartz, dolomite, ankerite, K-feldspar, clay minerals and minor amounts of gypsum and pyrite. The main reaction is the dissolution of the carbonates which is fastest for the highest flow rate injection and for the genuine Heletz brine. Permeability increases during the five percolation experiments, regardless of flow rate and brine type. This increase in permeability is associated to a decrease in porosity during the gypsum-equilibrated brine experiments due to gypsum precipitation. The precipitation of secondary minerals (kaolinite, muscovite and smectite) is mainly controlled by the dissolution of K-feldspar and largest at low flow rate injection, indicating that these precipitation processes are diffusion-controlled and localized in immobile zones where favorable chemical micro-environments exist. These processes are quantified by means of a reactive transport model. These results indicated that the CO2 injection at the Heletz site should trigger both permeability increase in interface between brine and CO2, which may extend over a large extension and where mixing processes are very active, especially near the well under intermittent injection conditions.
ISSN: 1750-5836

hal-01356329
https://hal.archives-ouvertes.fr/hal-01356329
DOI : 10.1016/j.ijggc.2015.10.023

Éditeur(s) : Elsevier
Résumé : The combined use of Lu-Hf and Sm-Nd isotope systems potentially offers a unique perspective for investigating continental erosion, but little is known about whether, and to what extent, the Hf-Nd isotope composition of sediments is related to silicate weathering intensity. In this study, Hf and Nd elemental and isotope data are reported for marine muds, leached Fe-oxide fractions and zircon-rich turbidite sands collected off the Congo River mouth, and from other parts of the SE Atlantic Ocean. All studied samples from the Congo fan (muds, Fe-hydroxides, sands) exhibit indistinguishable Nd isotopic composition (epsilon(Nd)similar to - 16), indicating that Fe-hydroxides leached from these sediments correspond to continental oxides precipitated within the Congo basin. In marked contrast, Hf isotope compositions for the same samples exhibit significant variations. Leached Fe-hydroxide fractions are characterized by epsilon(Hf) values (from -1.1 to +13) far more radiogenic than associated sediments (from -7.1 to -12.0) and turbidite sands (from -27.2 to -31.6). epsilon(Hf) values for Congo fan sediments correlate very well with Al/K (i.e. a well-known index for the intensity of chemical weathering in Central Africa). Taken together, these results indicate that (1) silicate weathering on continents leads to erosion products having very distinctive Hf isotope signatures, and (2) a direct relationship exists between epsilon(Hf) of secondary clay minerals and chemical weathering intensity. These results combined with data from the literature have global implications for understanding the Hf-Nd isotope variability in marine precipitates and sediments. Leached Fe-hydroxides from Congo fan sediments plot remarkably well on an extension of the 'seawater array' (i.e. the correlation defined by deep-sea Fe-Mn precipitates), providing additional support to the suggestion that the ocean Hf budget is dominated by continental inputs. Fine-grained sediments define a diffuse trend, between that for igneous rocks and the,seawater array', which we refer to as the 'zircon-free sediment array' (epsilon(Hf)=0-91 epsilon(Nd)+3.10). Finally, we show that the Hf-Nd arrays for seawater, unweathered igneous rocks, zircon-free and zircon-bearing sediments (epsilon(Hf)= 1.80 epsilon(Nd)+2.35) can all be reconciled, using Monte Carlo simulations, with a simple weathering model of the continental crust. (C) 2008 Elsevier B.V. All rights reserved.
Earth and Planetary Science Letters (0012-821X) (Elsevier), 2009 , Vol. 277 , N. 3-4 , P. 318-326

Droits : 2009 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2009/publication-6451.pdf
DOI:10.1016/j.epsl.2008.10.028
http://archimer.ifremer.fr/doc/00000/6451/