Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Abstract The functionality or oxidation state of cobalt within a silica matrix can be tailored through the use of cationic surfactants and their halide counter ions during the sol-gel synthesis. Simply by adding surfactant we could significantly increase the amount of cobalt existing as Co3O4 within the silica from 44% to 77%, without varying the cobalt precursor concentration. However, once the surfactant to cobalt ratio exceeded 1, further addition resulted in an inhibitory mechanism whereby the altered pyrolysis of the surfactant decreased Co3O4 production. These findings have significant implications for the production of cobalt/silica composites where maximizing the functional Co3O4 phase remains the goal for a broad range of catalytic, sensing and materials applications.
ISSN: 2045-2322

hal-01683204
https://hal.univ-antilles.fr/hal-01683204
DOI : 10.1038/srep02449

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
ISSN: 0144-8617

hal-00360370
https://hal.archives-ouvertes.fr/hal-00360370
DOI : 10.1016/j.carbpol.2008.04.021

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Mesoporous cobalt oxide silica matrices and membranes were successfully prepared using a dual acid-base catalysed sol-gel and interlayer-free approach for desalination applications. The effects of cobalt addition (0-35 mol%) on the structure-property relationship of the silica materials and membrane performance were systematically studied as a function of feed salt concentration (0.3-7.5 wt.% NaCl) and temperature (22-60 °C). As cobalt concentration increases beyond 5 mol%, the concentration of tricobalt tetroxide and proportion of silica mesopores were found to increase within the matrices. Silica membranes with high amount of tricobalt tetroxide (35 mol%) were found to be highly mesoporous with water fluxes of 20, 11.3 and 7.7 kg m-2 h-1 for the 0.3, 3.5 and 7.5 wt.% solutions at 60 °C, respectively, with >99.7% salt rejection at all times. This is attributed to the high pore volume (mesopores formation) and structural robustness of the silica network provided by the presence of tricobalt tetroxide. Even higher performance was achieved for low tricobalt tetroxide (mol%) silica membranes with water fluxes of 47.6 (0.3 wt.%) and 31.5 (3.5 wt.%) kg m-2 h-1 at 60 °C, respectively, though with reduced salt rejections of 90%. © 2015 Elsevier B.V.
ISSN: 0011-9164

hal-01683209
https://hal.univ-antilles.fr/hal-01683209
DOI : 10.1016/j.desal.2015.02.034

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : International audience
This paper presents the effects of chemical and thermal treatments on the strength of vegetable fibers that were being considered as reinforcements in cementitious matrix composites for affordable housing. These include vegetable fibers extracted from banana trunks and sugar cane residues. The results suggested that pyrolysis increased the fiber strength, at least by a factor three. Acid attack generally degraded the strengths, while alkali attack had only a limited effect. Pyrolyzed banana leaves, coconut coir, and coconut sheaths fibers were also tested. The implications of the results were discussed for the development of strong cementitious matrix composites.
ISSN: 1042-6914

hal-00809827
https://hal.univ-antilles.fr/hal-00809827
DOI : 10.1080/10426910601063386

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
ISSN: 1387-1811

hal-01680610
https://hal.univ-antilles.fr/hal-01680610
DOI : 10.1016/j.micromeso.2009.06.012

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
This work investigates the structural formation and analyses of titania membranes (TM) prepared using different vacuum exposure times for molecular weight (MW) cut-off performance and oil/water separation. Titania membranes were synthesized via a sol-gel method and coated on macroporous alumina tubes followed by exposure to a vacuum between 30 and 1200 s and then calcined at 400 °C. X-ray diffraction and nitrogen adsorption analyses showed that the crystallite size and particle size of titania increased as a function of vacuum time. All the TM membranes were mesoporous with an average pore diameter of ~3.6 nm with an anatase crystal morphology. Water, glucose, sucrose, and polyvinylpyrrolidone with 40 and 360 kDa (PVP-40 kDa and PVP-360 kDa) were used as feed solutions for MW cut-off and hexadecane solution for oil filtration investigation. The TM membranes were not able to separate glucose and sucrose, thus indicating the membrane pore sizes are larger than the kinetic diameter of sucrose of 0.9 nm, irrespective of vacuum exposure time. They also showed only moderate rejection (20%) of the smaller PVP-40 kDa, however, all the membranes were able to obtain an excellent rejection of near 100% for the larger PVP-360 kDa molecule. Furthermore, the TM membranes were tested for the separation of oil emulsions with a high concentration of oil (3000 ppm), reaching high oil rejections of more than 90% of oil. In general, the water fluxes increased with the vacuum exposure time indicating a pore structural tailoring effect. It is therefore proposed that a mechanism of pore size tailoring was formed by an interconnected network of Ti-O-Ti nanoparticles with inter-particle voids, which increased as TiO2 nanoparticle size increased as a function of vacuum exposure time, and thus reduced the water transport resistance through the TM membranes. © 2016 by the authors.
ISSN: 1996-1944

hal-01683214
https://hal.univ-antilles.fr/hal-01683214
DOI : 10.3390/ma9110938

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : International audience
Turbinaria turbinata brown seaweeds were tested as carbon electrode material in symmetric, electrochemical supercapacitors. The electrochemical properties of the carbon materials were characterised for their application as supercapacitors using cyclic voltammetry, galvanostatic charge/discharge method and electrochemical impedance spectroscopic analyses. Our initial results showed that the optimal behaviour was obtained for the sample prepared by pyrolysis at 800 degrees C. The average surface area of the carbon was 812 m(2)/g. Electrochemical tests with an organic electrolyte gave the following interesting results: a capacitance of 74.5 F/g, a specific series resistance of 0.5 Omega cm(2) and an ionic resistivity of 1.3 Omega cm(2). These results show the promising capacitive properties of carbon derived from seaweeds and their application in electrochemical supercapacitors. (C) 2013 Academie des sciences.
ISSN: 1631-0748

hal-00817880
http://hal.upmc.fr/hal-00817880
DOI : 10.1016/j.crci.2012.12.016

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Carbonised template silica membranes were synthesised and investigated for water desalination for brackish (0.3wt%), sea water (3.5wt%) and brine (7.5wt%) NaCl solutions at temperatures range from 22 to 60°C. The membranes were prepared by a two-step base catalysed sol-gel method using tetraethyl orthosilicate TEOS as the silica precursor and triblock copolymer of Pluronic® P123 as the templating agent. The P123 silica membranes calcined under vacuum only produced high quality membranes by the interlayer-free method. The membranes were stable during testing of up to 250h under different thermal and salt concentration solutions, always delivering very high salt rejections >99.5%. It was found that by increasing the template concentration in the silica matrix from 5 to 50wt%, salt concentration polarisation was greatly reduced. As such, high water fluxes were measured up to 8.5kgm-2h-1 for brackish water and 6.6kgm-2h-1 for brine water. © 2014 Elsevier B.V.
ISSN: 0376-7388

hal-01683210
https://hal.univ-antilles.fr/hal-01683210
DOI : 10.1016/j.memsci.2014.10.026

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Abstract View references (45)Graphene oxide-iron oxide (GO-Fe3O4) nanocomposites were synthesised by co-precipitating iron salts onto GO sheets in basic solution. The results showed that formation of two distinct structures was dependent upon the GO loading. The first structure corresponds to a low GO loading up to 10wt%, associated with the beneficial intercalation of GO within Fe3O4nanoparticles and resulting in higher surface area up to 409m2g-1. High GO loading beyond 10 wt% led to the aggregation of Fe3O4 nanoparticles and the undesirable stacking of GO sheets. The presence of strong interfacial interactions (Fe-O-C bonds) between both components at low GO loading lead to 20% higher degradation of Acid Orange 7 than the Fe3O4 nanoparticles in heterogeneous Fenton-like reaction. This behaviour was attributed to synergistic structural and functional effect of the combined GO and Fe3O4 nanoparticles.
ISSN: 2045-2322

hal-01683208
https://hal.univ-antilles.fr/hal-01683208
DOI : 10.1038/srep04594

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Four fibers from banana-trees (leaf, trunk) and coconut-tree (husk, fabric) were examined before their incorporation in cementitious matrices, in order to prepare insulating material for construction. Their botanical compositions have been determined following a method described previously. Thermal degradation of these fibers were studied between 200 and 700 °C under nitrogen gas flow. Temperature of pyrolysis was the experimental parameter investigated. The solid residues obtained were analyzed by classical elemental analysis, Fourier Transform Infra Red (FTIR) spectroscopy and were observed by Scanning Electron Microscopy (SEM). This study has shown (1) the relation between botanical, chemical composition with both localization of fibers in the tree and type of tree; (2) the rapid and preferential decomposition of banana fibers with increasing temperature of pyrolysis and (3) the rough samples are made of hollow fibers.
ISSN: 0960-8524

hal-00809780
https://hal.univ-antilles.fr/hal-00809780
DOI : 10.1016/j.biortech.2005.11.030

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
A series of graphene oxide (GO) and zinc partially substituted magnetite GO-Fe1-xZnxOy (0 ≤ x ≤ 0.285) catalysts were synthesised through a precipitation-oxidation method. The rate constants for the degradation of acid orange seven (AO7) proceeded at a significant faster rate under UV-irradiation (up to 670%) than the conventional heterogeneous Fenton-like reaction. The resultant catalysts were mesoporous, so there was no mass transfer limitation for AO7 to access active sites in the catalysts. Further, maximum increases of rate constant up to 220% occurred as the zinc molar concentration increased from x = 0 to x = 0.159. GO enhanced to incorporation of zinc into the combined metal oxide, whilst zinc limited crystal growth, thus forming smaller crystallite sizes. These features proved to be essential for the improved catalytic activity of the resultant catalysts. The optimised zinc molar value at x = 0.159 delivered the best catalytic activity. © The Royal Society of Chemistry 2016.
ISSN: 2046-2069

hal-01683215
https://hal.univ-antilles.fr/hal-01683215
DOI : 10.1039/c6ra04068c

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Abstract View references (35)La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) hollow fibres were prepared by a phase inversion/sintering method using polyetherimide as a binder. In order to overcome surface exchange kinetics limitation, LSCF hollow fibres were coated with ∼200nm palladium (Pd) nanoparticles. The O2 flux of best performing membranes increased by up to 350% in comparison to unmodified LSCF hollow fibres. Optimal enhancement was achieved with a single Pd coating. Additional coatings resulted in reduced O2 fluxes, thus counter acting the beneficial spill-over effect of the catalyst. Long term stability testing in atmospheric air at 850°C showed that a LSCF membrane modified with a single Pd coating continually outperformed a pure LSCF hollow fibre for over 400h, though the level of enhancement was reduced over time. A dramatic reduction in performance of more than 45% occurred within the first 24h of testing, which was attributed to the coalescence and aggregation of Pd catalyst particles to ∼1000nm size at the LSCF grain boundaries. This greatly reduced the available area for the oxygen species to spill-over onto the LSCF surface and thus reduced the overall O2 flux. © 2011 Elsevier B.V.
ISSN: 0376-7388

hal-01683196
https://hal.univ-antilles.fr/hal-01683196
DOI : 10.1016/j.memsci.2011.07.008

Éditeur(s) : HAL CCSD
Résumé : International audience
Catalysis Today

hal-01683192
https://hal.univ-antilles.fr/hal-01683192
DOI : 10.1016/j.cattod.2010.04.025

Éditeur(s) : HAL CCSD
Résumé : EGU2012-6377- Geophysical Research Abstracts vol. 14
The hot geothermal fluid produced by the wells of the Bouillante power station, in Guadeloupe, contains various dissolved species such as silica or some metals (Zn, Pb, etc). During the exploitation, the geothermal fluid is flashing and cooling (from 260 to 160°C for the high-pressure steam-liquid separation and down to 110°C for the low-pressure phase separation of a part of the separated liquid at 160°C). Consequently, the dissolved species can form scale deposits such as amorphous silica or poly-metallic sulphides, according to the exploitation conditions, and cause serious scaling problems on the production and the surface installations. These minerals could also precipitate during the partial underground re-injection of the production fluids which is being set up in the Bouillante power station. In this study, in order to predict and prevent the possible silica precipitation at temperature lower than 160°C, during the partial underground reinjection of the production fluids of Bouillante or their thermal valorization down to 110°C temperatures, we propose to investigate on site the kinetics of silica precipitation as a function of temperature and pH. The experiments presented here were carried out on site on samples of separated waters collected after the steam-water separator at 160°C, containing about 600 ppm of SiO2, at four cooling temperatures: 22, 50, 75 and 90°C, and for pH ranging from 4 to 9. These experiments showed that the silica deposition was always initiated by a polymerization mechanism characterized by an order 2 kinetic law and the formation of a white colloidal gel, which slowed down the silica precipitation under solid form. This latter was observed much later, after the polymerization stage, and only in particular conditions (long time of atmospheric exposure, water stagnation,. . . ). The results also confirmed that the silica precipitation kinetics is strongly dependent on pH. In acidic solution, a transition period is observed before the beginning to the silica polymerization. At neutral-basic pH, there is no transition period and the rate of polymerization is maximal for pH close to 8. The undergoing modeling of these experimental data and specific surface area measurements on the colloidal gel will allow us to determinate the kinetics parameters useful for the prediction and prevention of silica precipitation under the specific exploitation conditions of Bouillante power station. This work is financially supported by ADEME (French Agency for Energy and Environment), BRGM and UAG.
EGU General Assembly 2012
Vienne, Austria

hal-00697627
https://hal-brgm.archives-ouvertes.fr/hal-00697627

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
ISSN: 0022-2720

hal-01682104
https://hal.univ-antilles.fr/hal-01682104
DOI : 10.1046/j.1365-2818.2003.01170.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Thermogravimetric results on the thermal degradation of isolated components extracted from shells of tropical fruit stones and seeds allowed us to establish the dependence of the yield of char obtained by high-temperature pyrolysis (600-900 °C) of lignocellulosic raw materials on the content of components in precursors...
ISSN: 1387-1811

hal-00809743
https://hal.univ-antilles.fr/hal-00809743
DOI : 10.1016/S1387-1811(03)00288-9

Éditeur(s) : HAL CCSD Lavoisier
Résumé : International audience
Influence des constituants de la fibre de bagasse sur la prise du matériau composite bagasse/ciment
ISSN: 1169-7954

hal-00808663
https://hal.univ-antilles.fr/hal-00808663

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : International audience
This work evaluates the influence of three different intensities of refinement of sisal pulp and the effect of accelerated aging cycles on the behavior of composites. Fiber-cements were prepared by the slurry de-watering method and pressing as a crude simulation of the Hatschek process. Mechanical behavior of composites was evaluated by four-point bending test at 28 days, and after 50 and 100 wet/dry cycles. Refinement of pulp and aging have increased the strength and bulk density of composites and decreased the toughness and porosity. The best mechanical performance after aging was achieved for samples with highly refined fibers.
ISSN: 1042-6914

hal-00809817
https://hal.univ-antilles.fr/hal-00809817
DOI : 10.1080/10426910601062065

Éditeur(s) : HAL CCSD
Résumé : Composite materials incorporating vegetable fibres have known an increasingly interest during the past few decades. These environmental friendly materials are low-cost and offer advantages such as reduction of electrical consumption by air conditioning. Moreover, the use of vegetable fibres in replacement of synthetic fibre is interesting in developing countries where the availability of tropical plants and agricultural waste is important. This paper presents an initial investigation on the use of a construction material, composed of cement and pre-treated (heat or alkaline treatments) sugar cane bagasse fibres. The purpose of this study is to analyse the effect of fibre content and treatment on thermal conductivity, specific heat, flexural strength and density. The addition of retified fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline fibres. From mechanical point of view, composites made with alkaline fibres have a better flexural strength than others.
12th International Inorganic-bonded Fiber Composites Conference
Aalborg, Denmark

hal-00807543
https://hal.univ-antilles.fr/hal-00807543

Éditeur(s) : HAL CCSD University of Minho
Résumé : International audience
13th International Congress on Polymers in Concrete
Madeira, Portugal

hal-00807961
https://hal.univ-antilles.fr/hal-00807961