Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper examines the thermal properties of cement composites reinforced with vegetable bagasse fibres (1.5% and 3% wrtc). Thermal properties have been correlated to macroscopic density and porosity in order to estimate thermal conductivity of fibres using a calculation inspired from the Maxwell-Eucken modelling. Experimental investigations reveal that adding retified bagasse fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline bagasse fibres. Moreover, the more the fibres, the lighter the specimen; lower its thermal conductivity and lower its specific heat. Thermal conductivity of alkaline fibres is lower than retified fibres one.
ISSN: 1359-835X

hal-00809831
https://hal.univ-antilles.fr/hal-00809831
DOI : 10.1016/j.compositesa.2010.01.002

Éditeur(s) : HAL CCSD
Résumé : Composite materials incorporating vegetable fibres have known an increasingly interest during the past few decades. These environmental friendly materials are low-cost and offer advantages such as reduction of electrical consumption by air conditioning. Moreover, the use of vegetable fibres in replacement of synthetic fibre is interesting in developing countries where the availability of tropical plants and agricultural waste is important. This paper presents an initial investigation on the use of a construction material, composed of cement and pre-treated (heat or alkaline treatments) sugar cane bagasse fibres. The purpose of this study is to analyse the effect of fibre content and treatment on thermal conductivity, specific heat, flexural strength and density. The addition of retified fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline fibres. From mechanical point of view, composites made with alkaline fibres have a better flexural strength than others.
12th International Inorganic-bonded Fiber Composites Conference
Aalborg, Denmark

hal-00807543
https://hal.univ-antilles.fr/hal-00807543

Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084

Éditeur(s) : HAL CCSD
Résumé : International audience
Tension wood, a tissue developed by angiosperm trees to actively recover their verticality, has long been defined by the presence of an unlignified cellulosic inner layer in the cell wall of fibres, called the G-layer. Although it was known that some species have no G-layer, the definition was appropriate since it enabled easy detection of tension wood zones using various staining techniques for either cellulose or lignin. For several years now, irrespective of its anatomical structure, tension wood has been defined by its high mechanical internal tensile stress. This definition enables screening of the diversity of cell walls in tension wood fibres. Recent results obtained in tropical species with tension wood with a delay in the lignification of the G-layer opened our eyes to the effective presence of large amounts of lignin in the G-layer of some species. This led us to review older literature mentioning the presence of lignin deposits in the G-layer and give them credit. Advances in the knowledge of tension wood fibres allow us to reconsider some previous classifications of the diversity in the organisation of the fibre walls of the tension wood.
ISSN: 0928-1541

hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686/document
https://hal.archives-ouvertes.fr/hal-01636686/file/2017_Ghislain-Clair_IAWAJ_DiversityOrganisationLignificationTensionWoodFibreWalls-AReview.pdf
DOI : 10.1163/22941932-20170170

Éditeur(s) : HAL CCSD
Résumé : International audience
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood specimens were taken from the upper and lower sides of naturally tilted trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend. At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915/document
https://hal.archives-ouvertes.fr/hal-00194915/file/IAWA2006_RuelleClairBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001321

Éditeur(s) : HAL CCSD
Résumé : Couche G ou couche tertiaire : quel nom pour la couche interne des fibres du bois de tension ?. 11es Journées du Réseau Français des Parois
11es Journées du Réseau Français des Parois
Orléans, France

hal-01603178
https://hal.archives-ouvertes.fr/hal-01603178
PRODINRA : 398652

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called G-layer, in the fibre wall. The structure of G-layer has been recently described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2 to 50 nm). This led us to revisit the concept of G-layer that was until now only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with typical thick G-layer while it is much less with thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without G-layer is as low as in normal wood. Not depending on the amount of pores, the pore sizes distribution are always centred around 6-12 nm. These results suggest that, among species producing fibres with G-layer, large structural differences of G-layer exist between species
ISSN: 0022-0957

hal-00387861
https://hal.archives-ouvertes.fr/hal-00387861
DOI : 10.1093/jxp/erp133

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A
Résumé :  
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called the G-layer, in the fibre cell wall. The structure of the G-layer has recently been described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2-50 nm). This led us to revisit the concept of the G-layer that had been, until now, only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with a typical thick G-layer while it is much less with a thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without a G-layer is as low as in normal wood. Not depending on the amount of pores, the pore size distribution is always centred around 6-12 nm. These results suggest that, among species producing fibres with a G-layer, large structural differences of the G-layer exist between species.
Journal of Experimental Botany

hal-01032161
https://hal.archives-ouvertes.fr/hal-01032161
DOI : 10.1093/jxb/erp133

Éditeur(s) : HAL CCSD
Résumé : Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rainforest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of the G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579/document
https://hal.archives-ouvertes.fr/hal-00112579/file/IAWA2006_ClairRuelleBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001136

Éditeur(s) : HAL CCSD Walter de Gruyter
Résumé : absent
Holzforschung

hal-01031939
https://hal.archives-ouvertes.fr/hal-01031939
DOI : 10.1515/HF.2005.057

Éditeur(s) : HAL CCSD Linnean Society of London
Résumé : International audience
The circumscription of Salicaceae has recently been enlarged to include a majority of the species formerly placed in the polyphyletic tropical family Flacourtiaceae. Several studies have reported a peculiar and infrequently formed multilayered structure of tension wood in four of the tropical genera. Tension wood is a tissue produced by trees to restore their vertical orientation, and most studies have focused on trees developing tension wood by means of cellulose-rich, gelatinous fibres, as is known in Populus L. and Salix L. (Salicaceae s.s.). This study aims to determine if the multilayered structure of tension wood is an anatomical characteristic common in other Salicaceae, and if so, how its distribution correlates to phylogenetic relationships. Therefore, we studied the tension wood of 14 genera of Salicaceae as well as two genera of Achariaceae, one genus of Goupiaceae, and one genus of Lacistemataceae, families closely related to Salicaceae or formerly placed in Flacourtiaceae. Opposite wood and tension wood were compared with light microscopy and 3D Laser Scanning Confocal Microscopy. The results indicate that a multilayered structure of tension wood is common in the family except in Salix, Populus, and one of their closest relatives, Idesia polycarpa Maxim. We suggest that tension wood may be a useful anatomical character in understanding phylogenetic relationships in Salicaceae. Further investigation is still needed on the tension wood of several other putatively close relatives of Salix and Populus, in particular Bennettiodendron Merr., Macrohasseltia L.O.Williams and Itoa Hemsl.
ISSN: 0024-4074

hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845/document
https://hal.archives-ouvertes.fr/hal-01392845/file/GhislainEtAl2016_MultylayerTWSalicaceae_Bot_Jsur the_Lin_Soc_HALssfig.pdf
DOI : 10.1111/boj.12471

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0