Éditeur(s) : HAL CCSD
Résumé :  
Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rain forest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood, and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-01032051
https://hal.archives-ouvertes.fr/hal-01032051

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : Université des Antilles Études caribéennes
Résumé : Les grands domaines naturels, rattachés aux diverses stations de villégiature, étaient dépositaires des meilleurs lacs à truites, d’immenses territoires de sauvagine, de cerf de Virginie et d’un grand nombre de rivières à saumon. Si le littoral et la montagne ont agi comme attracteurs dans le cas de la villégiature, il en a été autrement pour les clubs de chasse et de pêche, qui sont apparus au milieu du XIXe siècle et se sont multipliés à compter de 1885. En l’occurrence, la mécanique à l’œuvre semble avoir posé la « grande nature » comme visée territoriale et le « coureur des bois » comme figure emblématique du héros romantique. L’argument développé dans cet article va s’employer à montrer que le tourisme et la villégiature ont constitué au Québec des procédures de valorisation positionnelle de nature géoanthropologique. Le « clubage » des Laurentides, au sens large du terme, aura constitué en ce sens le présupposé de leur colonisation intérieure. Qu’il s’agisse du lac Saint-Jean, de la Mauricie ou des Laurentides en général, on retrouve l’efficacité du parcours structural de l’établissement humain développé en géographie structurale : l’occupation utilitaire d’un territoire disponible présuppose non pas d’abord une transformation de la nature, mais une valorisation des positions abstraites par le tourisme et la villégiature. 
The large natural areas, linked to the various resorts, were custodians of the best trout lakes, huge areas of waterfowl, deer of Virginia and a large number of salmon rivers. If the coast and the mountains acted as attractors in the case of the holiday, it was different for the club hunting and fishing, which have emerged in the mid-nineteenth century and have increased from 1885. In this case, the mechanics at work seems to have raised the "great outdoors" as a territorial and "rider of the woods" as emblematic figure of the romantic hero. In this case, the mechanics at work seems to have raised the "great outdoors" as a territorial and "rider of the woods" as emblematic figure of the romantic hero. The argument developed in this article will seek to show that tourism and vacationing were in Quebec recovery procedures such as positional geo-anthropological. The “clubage” Laurentian, in the broadest sense, will be formed in this sense the assumption of internal colonization. Whether Lake Saint-Jean, Mauricie and Laurentides in general, we find the effectiveness of the structural pathways of human settlement geography developed structural: the occupation of territory utility presupposes not available not primarily a transformation of nature but a recovery of vague ... by the tourism and the holiday resort.
Québec

Droits : info:eu-repo/semantics/openAccess
urn:doi:10.4000/etudescaribeennes.3609
http://journals.openedition.org/etudescaribeennes/3609

Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either “artificially”, or by natural extractives.
Wood Science and Technology

hal-01096868
https://hal-agroparistech.archives-ouvertes.fr/hal-01096868
DOI : 10.1007/S00226-010-0393-8

Éditeur(s) : HAL CCSD
Résumé : International audience
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood specimens were taken from the upper and lower sides of naturally tilted trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend. At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915/document
https://hal.archives-ouvertes.fr/hal-00194915/file/IAWA2006_RuelleClairBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001321

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wood has a hierarchical structure involving several levels of organisation. The stiffness of wood relies on its capacity to transfer mechanical stress to its stiffest element at the lowest scale, namely crystalline cellulose. This study aims at quantifying to what extend crystalline cellulose contributes to wood stiffness depending on its moisture content. The crystal strains of cellulose were measured using X-ray diffraction on wet and dry specimens of spruce, based on a previously published methodology. The comparison between crystal strain and macroscopic strain shows that, during elastic loading, cellulose strain is lower than macroscopic strain. The means ratio of crystal/macroscopic strain amounts 0.85 for dry specimens and 0.64 for wet specimens. This strain ratio cannot be explained just by the projection effect due to the difference in orientation between cellulose microfibrils and cell wall, but results from deformation mechanisms in series with cellulose. Analysis shows that this series contribution represents a non-negligible contribution to wood compliance and is strongly moisture-dependent. This contribution amounts 9% for dry specimens and 33% for wet specimens, corresponding to a 4-fold increase in compliance for the series contribution. The origin of these strains is ascribed to mechanisms involving bending or shear strain at different scales, due to the fact that reinforcing element are neither perfectly straight nor infinitely long.
ISSN: 0266-3538

hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031/document
https://hal.archives-ouvertes.fr/hal-01425031/file/Art_Almeras_al_Contribution_cellulose_moisture-dependent_elastic_behavior_2017.pdf
DOI : 10.1016/j.compscitech.2016.11.025

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Functional ecology has long considered the support function as important, but its biomechanical complexity is only just being elucidated. We show here that it can be described on the basis of four biomechanical traits, two safety traits against winds (SW) and self-buckling (SB), and two motricity traits involved in sustaining an upright position, tropic motion velocity (MV) and posture control (PC). All these traits are integrated at the tree scale, combining tree size and shape together with wood properties. The assumption of trait constancy has been used to derive allometric scaling laws, but it was more recently found that observing their variations among environments and functional groups, or during ontogeny, provides more insights into adaptive syndromes of tree shape and wood properties. However, over-simplified expressions have often been used, possibly concealing key adaptive drivers. An extreme case of over-simplification is the use of wood basic density as a proxy for safety. Actually, since wood density is involved in stiffness, loads and construction costs, the impact of its variations on safety is non-trivial. Moreover, other wood features, especially the microfibril angle (MFA), are also involved. Furthermore, wood is not only stiff and strong, but it also acts as a motor for MV and PC. The relevant wood trait for that is maturation strain asymmetry. Maturation strains vary with cell wall characteristics such as MFA, rather than with wood density. Finally, the need for further studies about the ecological relevance of branching patterns, motricity traits and growth responses to mechanical loads is discussed.
ISSN: 0022-0957

hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904/document
https://hal.archives-ouvertes.fr/hal-00909904/file/Integrative_biomechanics_for_tree_Fournier_al.pdf
DOI : 10.1093/jxb/ert279

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimize cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: (1) providing data to optimise the settings for a given operation (batch approach) and (2) building predictive models that could be the basis of an online control systems for the machining processes (interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With potential industrial applications in focus, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Though not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technologic knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003/document
https://hal.archives-ouvertes.fr/hal-00876003/file/LABOMAP_Holzforschung_2009_denaud.pdf
ENSAM : http://hdl.handle.net/10985/7419

Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014

Éditeur(s) : HAL CCSD
Résumé :  
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood secimens were taken from the upper and lower sides of naturally titled trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend.At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-01032149
https://hal.archives-ouvertes.fr/hal-01032149

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either "artificially", or by natural extractives.
ISSN: 0043-7719

hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242/document
https://hal.archives-ouvertes.fr/hal-00804242/file/Anisotropy_wood_variational_properties_Bremaud_al_2011.pdf
DOI : 10.1007/s00226-010-0393-8

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Background : This study examines the radial trend in wood stiffness of tropical rainforest trees. The objective was to determine if the type of growing environment (exposed plantation or dense primary forest) would have an effect on this radial trend. Methods : The axial elastic modulus of wood samples, representing a pith to bark cross-section, of six trees from several French Guianese species (two of Eperua falcata, one of Eperua grandiflora, two of Carapa procera and one of Symphonia gloubulifera) was measured using a dynamic "forced vibration" method. Results : Primary forest trees were observed to have a decrease in wood stiffness from pith to bark, whereas plantation trees, from the same genus or species, displayed a corresponding increase in wood stiffness. Juvenile wood stiffness appears to vary depending on the environment in which the tree had grown. Conclusion : We suggest that the growth strategy of primary forest trees is to produce wood resistant to selfbuckling so that the height of the canopy may be obtained with the maximum of efficiency. In contrast, the growth strategy of the trees growing in an exposed plantation is to produce low-stiffness wood, important to provide flexibility in wind. Further experiments to study the behaviour of more species, with more individuals per species, growing across a range of physical environments, are required.
ISSN: 1286-4560

hal-00644335
https://hal.archives-ouvertes.fr/hal-00644335
https://hal.archives-ouvertes.fr/hal-00644335/document
https://hal.archives-ouvertes.fr/hal-00644335/file/McLean_al.pdf
DOI : 10.1007/s13595-011-0085-z

Éditeur(s) : HAL CCSD
Résumé :  
The main aspects of wood mechanics are approached through the role played by wood as the building material of the tree. The main concepts used by nature: progressive setting up of tree weight and architecture, multifunctional role of wood and adaptability to hazard and long-term evolution, are clarified together with their consequence on the multilayered, anisotropic nature of wood. The technological choices of the plant world as the cellular structure, the use of composite with oriented fibres and hydro-carbonated polymers, as well as the systematic prestressing of every new layer, bear obvious consequences on the type of mechanical behaviour of wood. The local control of the level of prestressing through minor modifications of the cell-wall biosynthesis allows the tree to adapt to conditions of light exploration that will evolve according to time and risk occurrence. This analysis of wood genesis process permits in return to improve our understanding of the mechanical behaviour of the material in relation with the parameters of the microstructure.
Comptes Rendus de l'Académie des Sciences Série 2

hal-01032151
https://hal.archives-ouvertes.fr/hal-01032151
DOI : 10.1016/S1620-7742(01)01380-0

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD
Résumé : Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rainforest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of the G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579/document
https://hal.archives-ouvertes.fr/hal-00112579/file/IAWA2006_ClairRuelleBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001136

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Few studies have investigated the influence of environmental conditions on the within-treevariation in Eucalyptus wood traits. The genotype and environment effects and their interactionsinfluence the wood properties. Their evaluations are crucial to estimate the genotype values andto select with efficiency. Thus, the aim of this study was to better understand the effect ofground slope and wind speed on the spatial variation of basic density (ρ), stiffness (MOE) andmicrofibril angle (MFA) of Eucalyptus wood. Wood discs cut along the trunk were sampledfrom 150 six-year-old Eucalyptus grandis x E. urophylla hybrids growing in 3 contrastinggrowing conditions influenced by ground slope and wind regime. Near Infrared (NIR)calibrations previously developed for ρ, MOE and MFA were used to predict in our discs. 2-Dplots presenting the spatial variation of predicted wood traits were compared. The higher theground slope, the greater the magnitude of radial variation in ρ, principally in the medium zoneof the trunk. The spatial variation of wood stiffness seems to be sensitive to two environmentalconditions. The MFA radial decreases were more pronounced where the wind speed was higher.At the base and top of the trees, however, there was no significant effect of growing conditionson the radial variation of the wood properties considered here.
ISSN: 0931-1890

hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896/document
https://hal.archives-ouvertes.fr/hal-01451896/file/Art_Gril_al_Spatial_variation_wood_density_2016.pdf
DOI : 10.1007/s00468-015-1327-8

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
*Context: Tree orientation is controlled by asymmetric mechanical stresses set during wood maturation. The magnitude of maturation stress differs between longitudinal and tangential directions, and between normal and tension woods. * Aims: We aimed at evaluating patterns of maturation stress on eucalypt plantation trees and their relation with growth, with a focus on tangential stress evaluation. * Methods: Released maturation strains along longitudinal and tangential directions were measured around the circumference of 29 Eucalyptus nitens trees, including both straight and leaning trees. * Results: Most trees produced asymmetric patterns of longitudinal maturation strain but more than half of the maturation strain variability occurred between trees. Many trees produced high longitudinal tensile stress all around their circumference. High longitudinal tensile stress was not systematically associated with the presence of gelatinous layer. The average magnitude of released longitudinal maturation strain was found negatively correlated to the growth rate. A methodology is proposed to ensure reliable evaluation of released maturation strain in both longitudinal and tangential directions. Tangential strain evaluated with this method was lower than previously reported. * Conclusion: The stress was always tensile along longitudinal direction and compressive along tangential direction, and their respective magnitude was positively correlated. This correlation does not result from a Poisson effect but may be related to the mechanism of maturation stress generation.
Annals of Forest Science

hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611/document
DOI : 10.1007/s13595-013-0318-4