Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We investigated the response of the crystal structure, lattice parameters, and unit-cell volume of hydrous layered silicate phlogopite at conditions relevant to subduction zone settings. We have used first principles simulation based on density functional theory to calculate the equation of state and full elastic constant tensor. Based on the generalized gradient approximation, the full single crystal elastic constant tensor with monoclinic symmetry shows significant anisotropy with the compressional elastic constants: c11 = 181 GPa, c22 = 185 GPa, c33 = 62 GPa, the shear elastic constants c44 = 14 GPa, c55 = 20 GPa, c66 = 68 Ga, and c46 = −6 GPa; the off diagonal elastic constants c12 = 48 GPa, c13 = 12 GPa, c23 = 12 GPa, c15 = −16 GPa, c25 = −5 GPa and c35 = −1 GPa at zero pressure. The elastic anisotropy of phlogopite is larger than most of the layered hydrous phases relevant in the subduction zone conditions. The shear anisotropy, AVS for phlogopite is ∼77% at zero pressure condition and although it decreases upon compression it remains relatively high compared to other hydrous phases relevant in the subduction zone settings. We also note that the shear elastic constants for phlogopite are relatively low. Phlogopite also has a high isotropic bulk VP/VS ratio ∼2.0. However, the VP/VS ratio also exhibits significant anisotropy with values as low as 1.49. Thus, phlogopite bearing metasomatized mantle could readily explain unusual VP/VS ratio as observed from seismological studies from the mantle wedge regions of the subduction zone.
ISSN: 0031-9201

hal-01115670
https://hal.archives-ouvertes.fr/hal-01115670
DOI : 10.1016/j.pepi.2014.05.004

Éditeur(s) : HAL CCSD
Résumé : International audience
BACKGROUND: The effects of pressure-controlled (PC) ventilation on the ventilatory and haemodynamic parameters during laparoscopy procedures had not been carefully assessed. This prospective cross-over study was undertaken to compare how volume-controlled (VC) and PC modes could affect pulmonary mechanics, gas exchange, and cardiac function in patients undergoing laparoscopy. METHODS: Twenty-one patients undergoing laparoscopic urological procedures had their lungs ventilated at the beginning with VC ventilation. PC ventilation was instituted at the end of the VC sequence. Ventilator settings were adjusted to keep tidal volume, respiratory rate, and Fi(o(2)) constant in every mode. A complete set of ventilatory, haemodynamic, and gas exchange parameters was obtained under VC after 40 min of pneumoperitoneum and 20 min after switching for PC. Transoesophageal echocardiography was performed in order to evaluate systolic and diastolic function of the heart. RESULTS: When VC was switched to PC, peak airway pressure decreased [mean (sd) 32 (6) vs 27 (6) cm H(2)O; P < 0.0001], peak inspiratory flow increased [17 (3) vs 48 (8) litre min(-1); P < 0.0001), and dynamic compliance improved [+15 (8)%]. No difference was noted for static airway pressure, static compliance, and arterial oxygenation. No significant change could be demonstrated in the systolic [left ventricular end-systolic wall stress 66 (16) vs 63 (14) x 10(3) dyn cm(-2) m(-2)] or diastolic function [early diastolic velocity 10.3 (2.5) vs 10.5 (2.7) cm s(-1)]. CONCLUSIONS: In this study, no short-term beneficial effect of PC ventilation could be demonstrated over conventional VC ventilation in patients with pneumoperitoneum.
BJA

hal-00689758
https://hal.archives-ouvertes.fr/hal-00689758
DOI : 10.1093/bja/aem166
PUBMED : 17626027

Résumé : Ce travail de thèse est consacré à l’étude d’équations d’évolution et d’équations différentielles à argument constant par morceaux. L’étude des équations différentielles à argument constant par morceaux est un domaine important car ces équations ont la structure de système dynanmique de longueur constante. La continuité des solutions conduit à une relation de récurrence entre les valeurs de cette dernière entre les points n et n+1, où n est un entier relatif quelconque. Par conséquent les équations différentielles à argument constant par morceaux combinent à la fois les propriétés des équations différentielles et des équations aux différences. Nous étudierons l’existence de solutions presque automorphes et S-asymptotiquement omega-périodiques d’équations d’évolutions et d’équations à argument constant par morceaux. L’étude de solutions presque automorphes et S’asymptotiquement omega periodiques est motivé par le fait que ces fonctions généralisent celle des fonctions périodiques. Nous obtiendrons donc des résultats concernant l’existence et l’unicité de solutions presque automorphes et S asymptotiquement omega périodiques de plusieurs équations d’évolutions. Cette problématique sera notamment étudiée dans le cadre des équations d’évolutions appartenant à la classe des équations différentielles à argument constant par morceaux.
This thesis deals with the study of evolution equations and differential equations with piecewise constant argument. Studies of such equations were motivated by the fact that they represent a hybrid of discrete and continuous dynamical systems and combine the properties of both differential and differential-difference equations. We study the existence of almost automorphic solutions and S asymptotically omega periodic solution of evolution equations and differential equations with piecewise constant argument. The study of almost automorphic and S asymptotically omega periodic functions is motivated by the fact that these functions generalize the concept of periodic functions. Therefore, we obtain results about existence and unicity of almost automorphic and S asymptotic omega periodic solution of evolution equations. We will study this problem considering evolution equations who belong to a class of differential equation with piecewise constant argument.

http://www.theses.fr/2013AGUY0599/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : The dense hydrous magnesium silicate called the D phase is the most likely candidate to recycle hydrogen into the lower mantle in subduction zones. As seismology represents the preferred method to detect this mineral in subduction zones, the single crystal elastic tensor has been calculated using first principle methods. A triple cell (View the MathML source) was used to account for an ordered ideal composition of the D phase to lower mantle pressures. The elastic tensor of the mineral at ambient conditions is predicted to be C11 = 387.7, C33 = 287.7, C44 = 100.4, C12 = 108.0, C13 = 51.1, C14 = − 14.6 in GPa with bulk modulus at zero pressure Ko = 163 GPa and a statistical error of about 4.0 GPa for all constants. The pressure derivatives of the elastic constants have been determined to pressure of 80 GPa. Our tensor correctly predicts the published experimental measurements of linear compressibility along the a- and c-axes, the logarithmic pressure derivative of the c/a axial ratio and bulk modulus at zero pressure. It contradicts the experimentally measured elastic tensor reported by (Liu, L.-G., Okamoto, K., Yang, Y.-J., Chen, C.-C., Lin, C.-C., 2004. Elasticity of single-crystal phase D (a dense hydrous magnesium silicate) by Brillouin spectroscopy. Solid State Commun. 132, 517–520), which fails to reproduce the experimental compressibility data. Using the elastic constants and density predicted to 85 GPa, the seismic anisotropy of P- and S-waves has been calculated as a function of pressure. The single crystal has high P-wave velocities and shear wave splitting in the basal plane below 20 GPa. At high pressures, the maximum P-wave velocities have threefold symmetry normal to a-axes in the basal plane, whereas the maximum shear wave splitting is parallel to a-axes with twofold symmetry. The D phase has high Vp and Vs anisotropy at ambient pressure, 17.6% for Vp and 19.9% for Vs. The Vp anisotropy decreases with increasing pressure to about 30 GPa, while it remains constant at 8% from 30 to 85 GPa. The Vs anisotropy decreases to 17% at 20 GPa and then increases to 22% at 85 GPa. The isotropic velocity ratios of S to P (Rs/p), bulk sound to S (Rphi/s) and density to S (Rρ/s) are calculated as a function of pressure. The Rs/p shows very little variation with pressure with low value of 0.6, whereas both Rphi/s and Rρ/s increase with pressure to peak values of 2.8 and 2.0 respectively at about 60 GPa. The presence of the D phase in subducted horizontal ‘stagnant' plates in the circum Pacific could contribute to a number of seismic observations, such as the observed velocity heterogeneity at depths between 500 and 1000 km and the fast S-waves travelling horizontally with horizontal polarization in this depth range. Further the lower density of the D phase compared with anhydrous minerals could influence buoyancy of the hydrated ‘stagnant' slabs. The transformation of the D phase to perovskite plus ferripericlase during thermal annealing may be responsible for horizontal slab seismogenesis.
ISSN: 0012-821X

hal-00406379
https://hal.archives-ouvertes.fr/hal-00406379
DOI : 10.1016/j.epsl.2007.04.053

Éditeur(s) : HAL CCSD
Résumé : National audience
We study various proofs of the characterization of constant functions, more precisely of the theorem: a derivable function, defined on a real interval, is constant if, and only if, its derivative is null. Our aim is to study the relationships of these proofs with the mathematical curriculum of secondary schools and the beginning of undergraduate studies in France, from various points of views (epistemological, historical, and didactical). This study leads to the construction of the mathematical site of the studied theorem and can serve as a basis for training activities around the fundamental theorems of elementary analysis.
Nous étudions plusieurs démonstrations de la caractérisation suivante des fonctions constantes : une fonction, définie sur un intervalle, dérivable est constante si, et seulement si, sa dérivée est nulle. Le but est d'étudier les relations entre ces démonstrations et le curriculum en France à la jonction entre la fin des études secondaires et le début des études supérieures, avec des apports venant de différents points de vue (épistémologique, historique, didactique). Cette étude mène à la construction du site mathématique local du théorème étudié et peut servir de base à des activités de formation autour des théorèmes fondamentaux de l'analyse élémentaire.
Recherches et Ressources en Éducation et Formation

hal-01529547
https://hal.univ-antilles.fr/hal-01529547
https://hal.univ-antilles.fr/hal-01529547/document
https://hal.univ-antilles.fr/hal-01529547/file/8_Delcroix-et-Silvy-2009.pdf

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
A full equilibrium treatment of molecular aggregation is presented for prototypes of 1D and 3D aggregates, with and without nucleation. By skipping complex kinetic parameters like aggregate size-dependent diffusion, the equilibrium treatment allows to predict directly time-independent quantities such as critical concentrations. The relationships between the macroscopic equilibrium constants for the different paths are first established by statistical corrections and so as to comply with the detailed balance constraints imposed by nucleation, and the composition of the mixture resulting from homogeneous aggregation is then analyzed using the polylogarithm function. Several critical concentrations are distinguished: the residual monomer concentation in equilibrium (RMC) and the critical nucleation concentration (CNC), that is the threshold concentration of total subunits necessary for initiating aggregation. When increasing the concentration of total subunits, the RMC converges more strongly to its asymptotic value, the equilibrium constant of depolymerization, for 3D aggregates and in case of nucleation. The CNC moderately depends on the number of subunits in the nucleus, but sharply increases with the difference between the equilibrium constants of polymerization and nucleation. As the RMC and CNC can be numerically but not analytically determined, ansatz equations connecting them to thermodynamic parameters are proposed
PCCP : Physical chemistry chemical physics

Droits : info:eu-repo/semantics/OpenAccess
hal-01565995
https://hal.archives-ouvertes.fr/hal-01565995
https://hal.archives-ouvertes.fr/hal-01565995/document
https://hal.archives-ouvertes.fr/hal-01565995/file/Aggregates_in_equilibrium.pdf
DOI : 10.1039/c6cp08369b

Éditeur(s) : HAL CCSD Ecological Society of America
Résumé : Although niche-based and stochastic processes, including dispersal limitation and demographic stochasticity, can each contribute to community assembly, it is difficult to quantify the relative importance of each process in natural vegetation. Here, we extend Shipley's maxent model (Community Assembly by Trait Selection, CATS) for the prediction of relative abundances to incorporate both trait-based filtering and dispersal limitation from the larger landscape and develop a statistical decomposition of the proportions of the total information content of relative abundances in local communities that are attributable to trait-based filtering, dispersal limitation, and demographic stochasticity. We apply the method to tree communities in a mature, species-rich, tropical forest in French Guiana at 1-, 0.25- and 0.04-ha scales. Trait data consisted of species' means of 17 functional traits measured over both the entire meta-community and separately in each of nine 1-ha plots. Trait means calculated separately for each site always gave better predictions. There was clear evidence of trait-based filtering at all spatial scales. Trait-based filtering was the most important process at the 1-ha scale (34%), whereas demographic stochasticity was the most important at smaller scales (37-53%). Dispersal limitation from the meta-community was less important and approximately constant across scales (similar to 9%), and there was also an unresolved association between site-specific traits and meta-community relative abundances. Our method allows one to quantify the relative importance of local niche-based and meta-community processes and demographic stochasticity during community assembly across spatial and temporal scales.
ISSN: 0012-9658

hal-01032424
https://hal.archives-ouvertes.fr/hal-01032424

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
The variation of elastic- wave velocities as a function of the direction of propagation through the Earth's interior is a widely documented phenomenon called seismic anisotropy. The geometry and amount of seismic anisotropy is generally estimated by measuring shearwave splitting, which consists of determining the polarization direction of the fast shear- wave component and the time delay between the fast and slow, orthogonally polarized, waves. In subduction zones, the teleseismic fast shear- wave component is oriented generally parallel to the strike of the trench(1), although a few exceptions have been reported (Cascadia(2) and restricted areas of South America(3,4)). The interpretation of shear- wave splitting above subduction zones has been controversial and none of the inferred models seems to be sufficiently complete to explain the entire range of anisotropic patterns registered worldwide(1). Here we show that the amount and the geometry of seismic anisotropies measured in the forearc regions of subduction zones strongly depend on the preferred orientation of hydrated faults in the subducting oceanic plate. The anisotropy originates from the crystallographic preferred orientation of highly anisotropic hydrous minerals (serpentine and talc) formed along steeply dipping faults and from the larger- scale vertical layering consisting of dry and hydrated crust - mantle sections whose spacing is several times smaller than teleseismic wavelengths. Fault orientations and estimated delay times are consistent with the observed shear- wave splitting patterns in most subduction zones.
ISSN: 0028-0836

hal-00412016
https://hal.archives-ouvertes.fr/hal-00412016
DOI : 10.1038/nature07376

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
Little is known of how linkage patterns between species change along environmental gradients. The small, spatially discrete food webs inhabiting tank-bromeliads provide an excellent opportunity to analyse patterns of community diversity and food-web topology (connectance, linkage density, nestedness) in relation to key environmental variables (habitat size, detrital resource, incident radiation) and predators: prey ratios. We sampled 365 bromeliads in a wide range of understorey environments in French Guiana and used gut contents of invertebrates to draw the corresponding 365 connectance webs. At the bromeliad scale, habitat size (water volume) determined the number of species that constitute food-web nodes, the proportion of predators, and food-web topology. The number of species as well as the proportion of predators within bromeliads declined from open to forested habitats, where the volume of water collected by bromeliads was generally lower because of rainfall interception by the canopy. A core group of microorganisms and generalist detritivores remained relatively constant across environments. This suggests that (i) a highly-connected core ensures food-web stability and key ecosystem functions across environments, and (ii) larger deviations in food-web structures can be expected following disturbance if detritivores share traits that determine responses to environmental changes. While linkage density and nestedness were lower in bromeliads in the forest than in open areas, experiments are needed to confirm a trend for lower food-web stability in the understorey of primary forests.
PLoS ONE

hal-00913931
https://hal.archives-ouvertes.fr/hal-00913931
https://hal.archives-ouvertes.fr/hal-00913931/document
DOI : 10.1371/journal.pone.0071735
OATAO : 10204

Éditeur(s) : HAL CCSD Society for Molecular Biology and Evolution
Résumé : International audience
Microsatellites (SSRs) are highly susceptible to expansions and contractions. When located in a coding sequence, the insertion or the deletion of a single unit for a mono-, di-, tetra-, or penta(nucleotide)-SSR creates a frameshift. As a consequence, one would expect to find only very few of these SSRs in coding sequences because of their strong deleterious potential. Unexpectedly, genomes contain many coding SSRs of all types. Here, we report on a study of their evolution in a phylogenetic context using the genomes of four primates: human, chimpanzee, orangutan, and macaque. In a set of 5,015 orthologous genes unambiguously aligned among the four species, we show that, except for tri- and hexa-SSRs, for which insertions and deletions are frequently observed, SSRs in coding regions evolve mainly by substitutions. We show that the rate of substitution in all types of coding SSRs is typically two times higher than in the rest of coding sequences. Additionally, we observe that although numerous coding SSRs are created and lost by substitutions in the lineages, their numbers remain constant. This last observation suggests that the coding SSRs have reached equilibrium. We hypothesize that this equilibrium involves a combination of mutation, drift, and selection. We thus estimated the fitness cost of mono-SSRs and show that it increases with the number of units. We finally show that the cost of coding mono-SSRs greatly varies from function to function, suggesting that the strength of the selection that acts against them can be correlated to gene functions.
ISSN: 1759-6653

hal-01544762
https://hal.archives-ouvertes.fr/hal-01544762
DOI : 10.1093/gbe/evt003

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Functional ecology has long considered the support function as important, but its biomechanical complexity is only just being elucidated. We show here that it can be described on the basis of four biomechanical traits, two safety traits against winds (SW) and self-buckling (SB), and two motricity traits involved in sustaining an upright position, tropic motion velocity (MV) and posture control (PC). All these traits are integrated at the tree scale, combining tree size and shape together with wood properties. The assumption of trait constancy has been used to derive allometric scaling laws, but it was more recently found that observing their variations among environments and functional groups, or during ontogeny, provides more insights into adaptive syndromes of tree shape and wood properties. However, over-simplified expressions have often been used, possibly concealing key adaptive drivers. An extreme case of over-simplification is the use of wood basic density as a proxy for safety. Actually, since wood density is involved in stiffness, loads and construction costs, the impact of its variations on safety is non-trivial. Moreover, other wood features, especially the microfibril angle (MFA), are also involved. Furthermore, wood is not only stiff and strong, but it also acts as a motor for MV and PC. The relevant wood trait for that is maturation strain asymmetry. Maturation strains vary with cell wall characteristics such as MFA, rather than with wood density. Finally, the need for further studies about the ecological relevance of branching patterns, motricity traits and growth responses to mechanical loads is discussed.
ISSN: 0022-0957

hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904/document
https://hal.archives-ouvertes.fr/hal-00909904/file/Integrative_biomechanics_for_tree_Fournier_al.pdf
DOI : 10.1093/jxb/ert279

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
1. Despite considerable interest in the application of plant functional traits to questions of community assembly and ecosystem structure and function, there is no consensus on the appropriateness of sampling designs to obtain plot-level estimates in diverse plant communities. 2. We measured 10 plant functional traits describing leaf and stem morphology and ecophysiology for all trees in nine 1-ha plots in terra firme lowland tropical rain forests of French Guiana (N = 4709). 3.We calculated, by simulation, the mean and variance in trait values for each plot and each trait expected under seven sampling methods and a range of sampling intensities. Simulated sampling methods included a variety of spatial designs, as well as the application of existing data base values to all individuals of a given species. 4. For each trait in each plot, we defined a performance index for each sampling design as the proportion of resampling events that resulted in observed means within 5% of the true plot mean, and observed variance within 20%of the true plot variance. 5. The relative performance of sampling designs was consistent for estimations of means and variances. Data base use had consistently poor performance for most traits across all plots, whereas sampling one individual per species per plot resulted in relatively high performance. We found few differences among different spatial sampling strategies; however, for a given strategy, increased intensity of sampling resulted in markedly improved accuracy in estimates of trait mean and variance. 6. We also calculated the financial cost of each sampling design based on data from our 'every individual per plot' strategy and estimated the sampling and botanical effort required. The relative performance of designs was strongly positively correlated with relative financial cost, suggesting that sampling investment returns are relatively constant. 7. Our results suggest that trait sampling for many objectives in species-rich plant communities may require the considerable effort of sampling at least one individual of each species in each plot, and that investment in complete sampling, though great, may be worthwhile for at least some traits.
ISSN: 0269-8463

hal-00594009
https://hal.archives-ouvertes.fr/hal-00594009

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The quasi-equilibrium approximation is acceptable when molecular interactions are fast enough compared to circuit dynamics, but is no longer allowed when cellular activities are governed by rare events. A typical example is the lactose operon (lac), one of the most famous paradigms of transcription regulation, for which several theories still coexist to describe its behaviors. The lac system is generally analyzed by using equilibrium constants, contradicting single-event hypotheses long suggested by Novick and Weiner (1957). Enzyme induction as an all-or-none phenomenon. Proc. Natl. Acad. Sci. USA 43, 553-566) and recently refined in the study of (Choi et al., 2008. A stochastic single-molecule event triggers phenotype switching of a bacterial cell. Science 322, 442-446). In the present report, a lac repressor (LacI)-mediated DNA immunoprecipitation experiment reveals that the natural LacI-lac DNA complex built in vivo is extremely tight and long-lived compared to the time scale of lac expression dynamics, which could functionally disconnect the abortive expression bursts and forbid using the standard modes of lac bistability. As alternatives, purely kinetic mechanisms are examined for their capacity to restrict induction through: (i) widely scattered derepression related to the arrival time variance of a predominantly backward asymmetric random walk and (ii) an induction threshold arising in a single window of derepression without recourse to nonlinear multimeric binding and Hill functions. Considering the complete disengagement of the lac repressor from the lac promoter as the probabilistic consequence of a transient stepwise mechanism, is sufficient to explain the sigmoidal lac responses as functions of time and of inducer concentration. This sigmoidal shape can be misleadingly interpreted as a phenomenon of equilibrium cooperativity classically used to explain bistability, but which has been reported to be weak in this system.
ISSN: 0022-5193

inserm-00818506
http://www.hal.inserm.fr/inserm-00818506
http://www.hal.inserm.fr/inserm-00818506/document
http://www.hal.inserm.fr/inserm-00818506/file/LacI-TeX.pdf
ARXIV : 1312.5566

Éditeur(s) : HAL CCSD Wiley
Résumé : Tank bromeliads form a conspicuous, yet neglected freshwater habitat in Neotropical forests. Recent studies driven by interests in medical entomology, fundamental aspects of bromeliad ecology and experimental research on food webs have, however, prompted increasing interest in bromeliad aquatic ecosystems. As yet, there is nothing in the literature about the life histories and environmental drivers of invertebrate population dynamics in tank bromeliads. Based on fortnightly samples taken over oneyear, size frequency plots and individual dry masses allowed us to establish the life cycles and growth rates of the dominant aquatic invertebrates in a common bromeliad species of French Guiana. Linear mixed-effect models and Mantel tests were used to predict changes in density, biomass, and growth rates in relation to temperature, rainfall, humidity and detrital resources. Annual variations in invertebrate densities and biomasses could be described according to three types of distribution: unimodal, bimodal or almost constant. Despite seasonal variations, precipitation, temperature, relative humidity and detritus concentration accounted significantly for changes in density and biomass, but we found no significant responses in growth rates of most invertebrate species. Species rather displayed non-seasonal life cycles with overlapping cohorts throughout the year. There was also a trend for delayed abundance peaks among congeneric species sharing similar functional traits, suggesting temporal partitioning of available resources. Beyond novel knowledge, quantitative information on life histories is important to predict food-web dynamics under the influence of external forcing and self-organisation. Our results suggest that changes in species distribution that will affect population dynamics through biotic interactions in space and/or time could have greater effects on food webs and ecosystem functioning than changes in environmental factors per se.
ISSN: 0046-5070

hal-01607779
https://hal.archives-ouvertes.fr/hal-01607779
DOI : 10.1111/fwb.12862
PRODINRA : 407311

Éditeur(s) : HAL CCSD Elsevier
Résumé : The correct characterization of the effective reactive transport dynamics is an important issue for modeling reactive transport on the Darcy scale, specifically in situations in which reactions are localized, that is when different reactions occur in different portions of the porous medium. Under such conditions the conventional approach of homogenizing only the porous medium chemistry is not appropriate. We consider here reactive transport in a porous medium that is characterized by mass transfer between a mobile and a distribution of immobile regions. Chemical and physical heterogeneities are reflected by distributions of kinetic reaction rate constants and residence times in the immobile zones. We derive an effective reactive transport equation for the mobile solute that is characterized by non-local physical mass transfer and reaction terms. Specifically, chemical heterogeneity is upscaled in terms of a reactive memory function that integrates both chemical and physical heterogeneity. Mass transfer limitations due to physical heterogeneity yield effective kinetic rate coefficients that can be much smaller than the volumetric average of the local scale coefficients. These results help to explain and quantify the often reported discrepancy between observed field reaction rate constants and the ones obtained under well mixed laboratory conditions. Furthermore, these results indicate that transport under physical and chemical heterogeneity cannot be upscaled separately.
ISSN: 0169-7722

hal-00617674
https://hal.archives-ouvertes.fr/hal-00617674
DOI : 10.1016/j.jconhyd.2010.06.002

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé :  
1. Despite considerable interest in the application of plant functional traits to questions of community assembly and ecosystem structure and function, there is no consensus on the appropriateness of sampling designs to obtain plot-level estimates in diverse plant communities. 2. We measured 10 plant functional traits describing leaf and stem morphology and ecophysiology for all trees in nine 1-ha plots in terra firme lowland tropical rain forests of French Guiana (N = 4709). 3.We calculated, by simulation, the mean and variance in trait values for each plot and each trait expected under seven sampling methods and a range of sampling intensities. Simulated sampling methods included a variety of spatial designs, as well as the application of existing data base values to all individuals of a given species. 4. For each trait in each plot, we defined a performance index for each sampling design as the proportion of resampling events that resulted in observed means within 5% of the true plot mean, and observed variance within 20%of the true plot variance. 5. The relative performance of sampling designs was consistent for estimations of means and variances. Data base use had consistently poor performance for most traits across all plots, whereas sampling one individual per species per plot resulted in relatively high performance. We found few differences among different spatial sampling strategies; however, for a given strategy, increased intensity of sampling resulted in markedly improved accuracy in estimates of trait mean and variance. 6. We also calculated the financial cost of each sampling design based on data from our 'every individual per plot' strategy and estimated the sampling and botanical effort required. The relative performance of designs was strongly positively correlated with relative financial cost, suggesting that sampling investment returns are relatively constant. 7. Our results suggest that trait sampling for many objectives in species-rich plant communities may require the considerable effort of sampling at least one individual of each species in each plot, and that investment in complete sampling, though great, may be worthwhile for at least some traits.
Functional Ecology

hal-01032175
https://hal.archives-ouvertes.fr/hal-01032175
DOI : 10.1111/j.1365-2435.2009.01600.x

Résumé : Les biofilms électroactifs (EA) sont des consortia bactériens mono ou pluri-espèces, qui ont la faculté d’échanger des électrons provenant de leur métabolisme avec les surfaces solides conductrices des électrodes. Cette découverte est à l’origine d’un nouveau dispositif énergétique : la pile à combustible microbienne (PACM). Depuis les années 2000, la littérature scientifique sur les biofilms EA et sur les PACM explose, notamment grâce à la découverte de bactéries capables de transférer par voie directe – par des pili ou protéines transmembranaires – des électrons vers les électrodes. Plusieurs sources de bactéries EA ont été à ce jour découvertes, allant de cultures pures à des communautés bactériennes plus complexes. Ces dernières sont issues de milieux aqueux naturels (milieux marins ou d’eau douce), industriels ou urbains (effluents d’industrie, eaux usées domestiques). La plupart de ces sources bactériennes proviennent d’environnements de climat tempéré. Dans ce travail de thèse, plusieurs sols de milieux humides de la Guyane ont été identifiés comme étant de sources de bactéries EA. Les expériences menées sous potentiel d’électrode imposé et constant ont permis d’étudier l’adhésion à la surface d’électrode des biofilms EA issus de la flore endogène des milieux sélectionnés. La formation de bioanodes et de biocathodes a été possible en présence respectivement d’acétate et d’oxygène dans les milieux. Une étude par voltammétrie cyclique a mis en évidence les pics d’oxydo-réduction en lien avec les échanges électroniques du biofilm EA et de l’électrode. En optimisant la procédure de formation des biofilms EA par chronoampérométrie (surface d’électrode plus importante, apport en continu et progressif du substrat), une densité de courant maximale de 12 A/m2 et un rendement faradique de 24 % ont été obtenus. Une autre méthode pour former des biofilms EA à partir d’un milieu choisi, la mangrove, a consisté à utiliser deux prototypes de PACM : une pile à compartiment unique et à cathode à air, et une pile benthique. Dans les deux cas, les biofilms EA ont pu être formés et étudiés, complétant certaines observations faites sous potentiel imposé. La PACM benthique s’est avérée être la plus proche d’une application à grande échelle puisqu’elle a été complètement autonome : anode et cathode utilisant uniquement le milieu pour fonctionner. Elle a pu être étudiée en laboratoire comme sur le terrain.
Electroactive biofilms (EA) are mono or multi-species bacterial consortia, which have the ability to exchange electrons from their metabolism with solid surfaces of conductive electrodes. This discovery is the basis for a device of energy production: microbial fuel cell (MFC). Since the 2000s, the scientific literature on EA biofilms and MFC explodes, thanks to the discovery of bacteria that are able to transfer directly – by pili or trans-membrane proteins – electrons to electrodes. Several sources of EA bacteria were discovered to date, ranging from pure cultures to more complex bacterial communities. Those last are from natural (marine and freshwater), industrial or urban (industrial effluents, domestic wastewater) aqueous environments. However, the vast majority of these are from temperate environments.In this thesis, several wetland soils of French Guiana have been identified as sources of EA bacteria. Experiments under poised and constant electrode potential were used to examine adherence to the electrode surface of EA biofilms from the endogenous flora of selected environments. Formation of bioanodes and biocathodes was possible in the presence respectively of acetate and oxygen in the media. A study by cyclic voltammetry showed the redox peaks related to electronic exchanges between EA biofilm and electrode. By optimizing the process of EA biofilm formation by chronoamperometry (larger electrode surface, providing continuous and progressive substrate), a maximum current density of 12 A/m2 and a coulombic efficiency of 24% were obtained.Another method to form EA biofilms from a chosen medium (mangrove) was to use two MFC prototypes: a single compartment and air cathode one, and a benthic one. In both cases, the EA biofilms have been trained and studied supplementing certain observations made under poised polarization. MFC benthic proved to be the closest to a wide application since it was completely autonomous, anode and cathode only using the medium to function. It has been studied in the laboratory and in the field.

http://www.theses.fr/2012AGUY0560/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Synthetic hydroxylated titanium-bearing and undoped MgO-buffered forsterite crystals were heated at atmospheric pressure in air at temperatures from 800 to 1200 °C to determine hydrogen diffusion as a function of the type of point-defect mechanism by which the hydroxyl is incorporated. OH-stretching bands, measured by infrared spectroscopy, were assigned to the four substitution mechanisms: Ti-clinohumite point defects, silicon and magnesium vacancies, and point defects associated with trivalent cations. In the experiments at 800 to 1000 °C, hydrous defects related to trivalent cations and Mg-vacancies disappear first in the Ti-doped forsterite, followed by the hydrous defects related to Ti and a fraction of the hydrated Si-vacancies. Measured bulk diffusion coefficients for hydrogen exchange related to the latter process are one order of magnitude slower than previously reported and with higher activation energy (View the MathML source296±14 kJmol−1). After the elimination of the defects related to Ti, the hydroxyl concentration related to Si-vacancies remained constant for the duration of the experiments. This observation is in agreement with the very slow diffusivity of hydrogen in Si-vacancies measured in the undoped MgO-buffered dehydroxylation experiments at higher temperatures (from 1000 to 1200 °C), which were ∼3 orders of magnitude slower than previously reported at 1000 °C, and with an activation energy of View the MathML source461±11 kJmol−1. Hydrogen diffusion in forsterite is far more complex than previously assumed. This complexity can be used to gain more information on the timescales of the processes causing olivine to lose its structural “water”, but quantitative modeling will require not only the knowledge of the intrinsic diffusivities of the different hydrous defects but also their relative proportions and the possible reactions between them.
ISSN: 0012-821X

hal-01172253
https://hal.archives-ouvertes.fr/hal-01172253
DOI : 10.1016/j.epsl.2014.01.055

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
International audience
The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three-dimensional strains were measured at different parts of the trunk base. Risks of failure were greater on the buttress sides, where shear and tangential stresses are greater, not on the ridges, in spite of high longitudinal (parallel to the grain) stresses. A simple beam model, computed from the second moment of area of digitized cross sections, is consistent with longitudinal strain variations but cannot predict accurately variations with height. Patterns of longitudinal strain variation along ridges are very different in the two individuals, owing to a pronounced lateral curvature in one specimen. The constant stress hypothesis is discussed based on these results. Without chronological data during the development of the tree, it cannot be proved that buttress formation is activated by stress or strain.
ISSN: 0002-9122

hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155/document
https://hal.archives-ouvertes.fr/hal-01032155/file/Biomechanics_buttressed_trees_Clair_al_2003.pdf
DOI : 10.3732/ajb.90.9.1349

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Despite many studies, our understanding of silica precipitation from natural waters remains limited, in particular for geothermal waters. Here we present a detailed study on the kinetics of silica polymerization as a function of fluid temperature and pH using high-temperature (250-260 °C) seawater-derived geothermal fluids as those discharged from the Bouillante geothermal site.We monitored the on-site decrease in monomeric silica concentration(initial SiO2 concentration of about 600 mg/l)with time using the molybdenum blue spectrophotometric method on samples of separated water collected from the high-pressure separator at 167 °C and cooled to 25, 50, 75, and 90 °C and for pH values ranging from 5 to 8. During all these experiments, only silica polymerization was observed, with the formation of colloidal particles in suspension in the solutions. No scaling of amorphous silica was formed. The collected data were after modeled in order to determine the useful kinetic parameters for predicting and preventing amorphous silica precipitation in the production wells during fluid exploitation in the specific context of Bouillante. Results under the investigated experimental conditions show that the kinetics of silica precipitation is affected more strongly by pH than by temperature change. The reaction in the acidic Bouillante solution begins with a transition period that significantly decreases the kinetics of silica polymerization. Modeling the experimental data indicates that the silica polymerization up to the state of equilibrium is characterized by a 2nd-order kinetic law relative to dissolved silica; this could indicate that the polymerization is controlled mainly by the formation of dimers. However, the first hour of the experiments is better characterized by a 4th-order kinetic law, suggesting more complex polymerization reactions in the initial stage with the formation of nanocolloidal particles containing 3 to 4 monomers. In both cases, the corresponding kinetics rate constant k is linearly dependent on pH for pH between 5 and 7. The activation energy Ea for the overall reaction, calculated using the Arrhenius equation under the considered pH and temperature conditions, ranges between 41±9.8 and 54±9.6 kJ/mol. To complete this work, the colloid particles formed at the end of the kinetics experiments were extracted and analyzed by SEM and TEM microscopy, X-ray Diffraction and the BET method. Results show that the size of the colloids increase and their specific surface decrease with increasing pH and are thus dependent on pH. Globally, our work provides a reliable database for understanding silica polymerization kinetics in natural geothermal brines or geologic waters characterized by a near neutral pH and moderate dissolved silica concentrations.
ISSN: 0009-2541

hal-01403092
https://hal-brgm.archives-ouvertes.fr/hal-01403092
DOI : 10.1016/j.chemgeo.2016.08.031