Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
A versatile sol-gel route has been developed for the preparation of hierarchical porous silica membrane material with highly dispersed platinum nanoparticles (Pt-NPs). The outstanding feature of the "one pot" synthesis developed in this work lies in the successful preparation of a stable complex suspension made of silica sol, multi-scale porogens and Pt nanoparticles. The multi-scale porogens were based on non-ionic triblock copolymers and aqueous latex suspension to create mesopores and macropores, respectively, with finely tuned pore size and organization. For further functionalization of the membranes, Pt nanoparticles of about 4 nm in diameter were prepared by irradiating with microwaves (MW) the Pt precursors added in the starting suspension. This original path is suggested to enable a pre-organization of Pt nanoparticles in the ordered mesoporous structure. The suspensions were then deposited as thin films on either dense or macroporous supports, and further thermally treated at 450°C to remove the porogen units. Hierarchical porous layers composed of micropores (<2 nm), ordered mesopores (∼4 nm) and macropores (∼70 nm) with or without Pt were prepared and characterized. The resulting membranes are foreseen to exhibit great potential as multifunctional membranes for gas separation coupled with catalytic reaction. © The Royal Society of Chemistry 2008.
ISSN: 0959-9428

hal-01680586
https://hal.univ-antilles.fr/hal-01680586
DOI : 10.1039/b807029f

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The 12 May 2008 the Sichuan earthquake was one of the worst natural disasters in China. Here, we present a detailed picture of the epicentral area inferred geophysical data. Based on the analysis of teleseismic data acquired by a dense seismic network, we highlight an abrupt 20 km Moho offset between the Sichuan Basin and the Tibetan plateau and a horizontal discontinuity at similar to 15 km depth, which may connect with the ruptured zone of the 2008 event. We obtain low mean crustal velocity ratios, which suggest the absence of a thick and extensive zone of partial melt within the crust beneath the eastern part of the Songpan-Garze Terrane. All our data support the idea that the Longmen Shan range mark a zone of active strain localization due to the rigid Yangtze craton resisting eastward displacement of the Tibetan Plateau.
ISSN: 0040-1951

hal-00534471
https://hal.archives-ouvertes.fr/hal-00534471
DOI : 10.1016/j.tecto.2009.11.010

Éditeur(s) : HAL CCSD Wiley
Résumé : Negative density dependence (NDD) and environmental filtering (EF) shape community assembly, but their relative importance is poorly understood. Recent studies have shown that seedlings mortality risk is positively related to the phylogenetic relatedness of neighbours. However, natural enemies, whose depredations often cause NDD, respond to functional traits of hosts rather than phylogenetic relatedness per se. To understand the roles of NDD and EF in community assembly, we assessed the effects on seedling mortality of functional similarity, phylogenetic relatedness and stem density of neighbouring seedlings and adults in a species-rich tropical forest. Mortality risks increased for common species when their functional traits departed substantially from the neighbourhood mean, and for all species when surrounded by close relatives. This indicates that NDD affects community assembly more broadly than does EF, and leads to the tentative conclusion that natural enemies respond to phylogenetically correlated traits. Our results affirm the prominence of NDD in structuring species-rich communities.
ISSN: 1461-023X

hal-01032429
https://hal.archives-ouvertes.fr/hal-01032429
DOI : 10.1111/j.1461-0248.2011.01705.x

Éditeur(s) : Amer Geophysical Union
Résumé : The hydrological and geochemical properties of the waters constituting the Pacific Equatorial Undercurrent (EUC) determine the properties of the equatorial cold tongue. Understanding and quantifying the various EUC origins is therefore of prime importance. For this purpose, a high-resolution (1/4 degrees) interannual oceanic simulation was analyzed from the western tropical Pacific boundaries to 140 degrees W, using a Lagrangian framework. Waters from the Low-Latitude Western Boundary Currents (LLWBCs) transiting from Vitiaz Strait (the main contributor), from Solomon Strait, and via the Mindanao Current were identified as the principal sources to the EUC. Waters conveyed by the interior ocean off equator are negligible till 180 E. The LLWBCs' waters represent 87% of the EUC transport at 156 degrees E out of which the New Guinea Coastal Undercurrent (NGCU) is as large as 47%. The EUC meridional distribution suggests that the waters originating from Solomon Strait and Mindanao Current mostly remain in the hemisphere from which they originate. Contrastingly, Vitiaz Strait waters are found in both hemispheres. The vertical EUC distribution shows that the lower layer of the EUC is mainly composed of Vitiaz Strait waters. Finally, the source transport distributions were characterized, at their origin and within the EUC, as a function of density. These distributions showed that waters flowing through Vitiaz Strait at densities higher than those of the EUC (down to sigma(theta) = 27.2 kg m(-3)) undergo a diapycnal mixing and lighten during their journey to join the EUC. This lightening supports the suggestion that the NGCU is a major source for the EUC geochemical enrichment.
Journal Of Geophysical Research-oceans (0148-0227) (Amer Geophysical Union), 2011-12 , Vol. 116 , N. C12044 , P. 16 p.

Droits : 2011 by the American Geophysical Union
http://archimer.ifremer.fr/doc/00060/17105/14621.pdf
DOI:10.1029/2011JC007477
http://archimer.ifremer.fr/doc/00060/17105/

Éditeur(s) : Actes du IIIème Congrès International des Sociétés Françaises de Malacologie. Les mollusques dans la recherche actuelle, La Rochelle, France, 24-27 juin 2003
Résumé : We analysed a few aspects of oyster culture in New Caledonia. Oyster culture there is not very important, one farm producing 30 tonnes of Japanese oysters per year and the other one, 3 tonnes of rock oysters. Mangrove oyster deposits are traditionally exploited, and this exploitation lead to a decrease of the densities and biomasses observed in the most exploited estuaries. On the four monitored sites, the maximum size observed is comprised between 7.2 to 10 cm, for a mode comprised between 3.6 and 4.8 cm. Densities go from 31 to 251 oysters and biomasses, from 0.751 to 2.553 kg/m2. Regulations focus on the minimum collection size (6 cm) and a fishing prohibition period of 8 months. Based on our observations, we suggest that these dispositions be maintained. We also suggest that a fishing licence for professional fishermen be created, and that leisure fishing be maintained.
On a analysé quelques aspects de l'exploitation des huîtres en Nouvelle Calédonie. La conchyliculture y est faiblement présente, une ferme produisant 30 tonnes par an d'huîtres japonaises et une autre, 3 tonnes d'huîtres de rocher. Les gisements d'huître de palétuvier font l'objet d'une exploitation traditionnelle, qui a conduit à l'affaiblissement des densités et des biomasses observées dans les estuaires les plus exploités. Dans les quatre sites échantillonnés, la taille maximale observée allait de 7,2 à 10 cm, pour un mode compris entre 3,6 et 4,8 cm. Les densités allaient de 31 à 251 huîtres et les biomasses, de 0,751 à 2,553 kg/m2 . Les mesures réglementaires en vigueur concernent la taille minimale de capture (6 cm), et une période de fermeture de la pêche de 8 mois. Les observations faites suggèrent de maintenir ces dispositions. Il est également proposé de créer une licence de pêche pour des pêcheurs professionnels, et de maintenir une pêche de loisir.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2003/acte-6527.pdf
http://archimer.ifremer.fr/doc/00000/6527/

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Direct numerical simulations of flow through two millimeter-scale rock samples of limestone and sandstone are performed using three diverse fluid dynamic simulators. The resulting steady-state velocity fields are compared in terms of the associated empirical probability density functions (PDFs) and key statistics of the velocity fields. The pore space geometry of each sample is imaged at 5.06−μm voxel size resolution using X-ray microtomography. The samples offer contrasting characteristics in terms of total connected porosity (about 0.31 for the limestone and 0.07 for the sandstone) and are typical of several applications in hydrogeology and petroleum engineering. The three-dimensional fluid velocity fields within the explicit pore spaces are simulated using ANSYS® FLUENT® ANSYS Inc. (2009), EULAG Prusa et al. (Comput. Fluids 37, 1193–1207 2008), and SSTOKES Sarkar et al. (2002). These computational approaches are highly disperse in terms of algorithmic complexity, differ in terms of their governing equations, the adopted numerical methodologies, the enforcement of internal no-slip boundary conditions at the fluid-solid interface, and the computational mesh structure. As metrics of comparison to probe in a statistical sense the internal similarities/differences across sample populations of velocities obtained through the computational systems, we consider (i) integral quantities, such as the Darcy flux and (ii) main statistical moments of local velocity distributions including local correlations between velocity fields. Comparison of simulation results indicates that mutually consistent estimates of the state of flow are obtained in the analyzed samples of natural pore spaces despite the considerable differences associated with the three computational approaches. We note that in the higher porosity limestone sample, the structures of the velocity fields obtained using ANSYS FLUENT and EULAG are more alike than either compared against the results obtained using SSTOKES. In the low-porosity sample, the structures of the velocity fields obtained by EULAG and SSTOKES are more similar than either is to the fields obtained using ANSYS FLUENT. With respect to macroscopic quantities, ANSYS FLUENT and SSTOKES provide similar results in terms of the average vertical velocity for both of the complex microscale geometries considered, while EULAG tends to render the largest velocity values. The influence of the pore space structure on fluid velocity field characteristics is also discussed.
ISSN: 1420-0597

hal-01174152
https://hal.archives-ouvertes.fr/hal-01174152
DOI : 10.1007/s10596-015-9486-7

Éditeur(s) : HAL CCSD BioMed Central
Résumé : International audience
ABSTRACT: BACKGROUND: Climate change poses unprecedented challenges, ranging from global and local policy challenges to personal and social action. Heat-related deaths are largely preventable, but interventions for the most vulnerable populations need improvement. Therefore, the prior identification of high risk areas at the community level is required to better inform planning and prevention. We aimed to demonstrate a simple and flexible conceptual framework relying upon satellite thermal data and other digital data with the goal of easily reproducing this framework in a variety of urban configurations. RESULTS: The study area encompasses Rennes, a medium-sized French city. A Landsat ETM + image (60 m resolution) acquired during a localized heatwave (June 2001) was used to estimate land surface temperature (LST) and derive a hazard index. A land-use regression model was performed to predict the LST. Vulnerability was assessed through census data describing four dimensions (socio-economic status, extreme age, population density and building obsolescence). Then, hazard and vulnerability indices were combined to deliver a heatwave health risk index. The LST patterns were quite heterogeneous, reflecting the land cover mosaic inside the city boundary, with hotspots of elevated temperature mainly observed in the city center. A spatial error regression model was highly predictive of the spatial variation in the LST (R2 = 0.87) and was parsimonious. Three land cover descriptors (NDVI, vegetation and water fractions) were negatively linked with the LST. A sensitivity analysis (based on an image acquired on July 2000) yielded similar results. Southern areas exhibited the most vulnerability, although some pockets of higher vulnerability were observed northeast and west of the city. The heatwave health risk map showed evidence of infra-city spatial clustering, with the highest risks observed in a north--south central band. Another sensitivity analysis gave a very high correlation between 2000 and 2001 risk indices (r = 0.98, p < 10-12). CONCLUSIONS: Building on previous work, we developed a reproducible method that can provide guidance for local planners in developing more efficient climate impact adaptations. We recommend, however, using the health risk index together with hazard and vulnerability indices to implement tailored programs because exposure to heat and vulnerability do not require the same prevention strategies.
ISSN: 1476-072X

inserm-00762303
http://www.hal.inserm.fr/inserm-00762303
http://www.hal.inserm.fr/inserm-00762303/document
http://www.hal.inserm.fr/inserm-00762303/file/1476-072X-11-38.pdf
DOI : 10.1186/1476-072X-11-38

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : A differential effective medium (DEM) model is used to predict elastic properties for a set of porous and anisotropic aggregates, comprised of mixtures of calcite and muscovite. The DEM takes into consideration an anisotropic background medium with triclinic or higher symmetry, in which inclusions of idealized ellipsoidal shape are added incrementally. In general, the calculated elastic properties of a solid that contains inclusions representing "dry" pores/cracks are strongly dependent on the orientation and aspect ratio of the inclusions. Aspect ratios of inclusions in the synthetic aggregates, which consist of air-filled pores, are estimated from anisotropy of magnetic susceptibility (AMS) of samples whose pore space has been impregnated with a colloidal ferrofluid. The AMS derived pore shape geometry is used as an input value for inclusions in the DEM. Modeling results are compared with laboratory determined elastic properties, measured with ultrasonic waves. Calculated shear wave velocities agree in general well with laboratory measured S wave velocities, whereas calculated P wave velocities are typically 0.5-1.1 km/s higher than measured values. Differences between calculated and measured P wave velocities are attributed mainly to incomplete and biased ferrofluid saturation of pores. Spherical pores are preferably filled during imbibition, in comparison to thin cracks, which leads to overprediction of the calculated P wave velocities. The amount of ferrofluid that fills the pore space is dependent on the ratio of calcite to muscovite and the load used for compaction during sample synthesis. The permeability decreases with increasing muscovite content and increasing compaction load. Incomplete saturation of samples with high-muscovite content is confirmed by X-ray microtomography density contrast imaging of dry and ferrofluid saturated specimens.
ISSN: 0148-0227

hal-00617717
https://hal.archives-ouvertes.fr/hal-00617717
DOI : 10.1029/2010JB007750

Éditeur(s) : HAL CCSD Geological Society of America
Résumé : International audience
Integrated Ocean Drilling Program Expedition 313 continuously cored uppermost Eocene to Miocene sequences on the New Jersey shallow shelf (Sites M27, M28, and M29). Previously, 15 Miocene (ca. 23-13 Ma) seismic sequence boundaries were recognized on several generations of multichannel seismic profi les using criteria of onlap, downlap, erosional truncation, and toplap. We independently recognize sequence boundaries in the cores and logs based on an integrated study of core surfaces, lithostratigraphy and process sedimentology (grain size, mineralogy, facies, and paleoenvironments), facies successions, stacking patterns, benthic foraminiferal water depths, downhole logs, core gamma logs, and chronostratigraphic ages. We use a velocitydepth function to predict the depths of seismic sequence boundaries that were tested by comparison with major core surfaces, downhole and core logs, and synthetic seismograms. Using sonic velocity (core and downhole), core density, and synthetic seismograms, we show that sequence boundaries correspond with acoustic impedance contrasts, although other stratal surfaces (e.g., maximum fl ooding and transgressive surfaces) also produce refl ections. Core data are suffi cient to link seismic sequence boundaries to impedance contrasts in 9 of 12 instances at Site M27, 6 of 11 instances at Site M28, and 8 of 14 instances at Site M29. Oligocene sequences have minimal lithologic and seismic expression due to deep-water locations on clinoform bottomsets. Miocene sequences (ca. 23-13 Ma) were sampled across several unconformity clinothems (prograding units) on topset, foreset, and bottomset locations. Excellent recovery allows core-seismic integration that confi rms the hypothesis that unconformities are a primary source of impedance contrasts. Our core-seismic-log correlations predict that key seismic surfaces observed in other sub surface investigations without core and/or well logs are stratal surfaces with sequence stratigraphic signifi cance.
EISSN: 1553-040X

insu-00946235
https://hal-insu.archives-ouvertes.fr/insu-00946235
DOI : 10.1130/GES00858.1

Éditeur(s) : HAL CCSD Cambridge University Press (CUP)
Résumé : The objective of this study was to analyse the factors explaining spatial variation in soil respiration over topographic transects in a tropical rain forest of French Guiana. The soil of 30 plots along six transects was characterized. The appearance of the 'dry to the touch' character at a depth of less than 1.2 m was used to discriminate soils exhibiting vertical drainage from soils exhibiting superficial lateral drainage and along with colour and texture, to define five classes from well-drained to strongly hydromorphic soils. Spatial variation in soil respiration was closely related to topographic position and soil type. Increasing soil water content and bulk density and decreasing root biomass and soil carbon content explained most of the decrease in soil respiration from the plateaux (vertically drained hypoferralic acrisol) to the bottomlands (haplic gleysol). These results will help to stratify further field experiments and to identify the underlying determinants of spatial variation in soil respiration to develop mechanistic models of soil respiration.
ISSN: 0266-4674

hal-01032046
https://hal.archives-ouvertes.fr/hal-01032046
DOI : 10.1017/S0266467406003415

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
With only a narrow opening through the Gibraltar and Suez Canals, the Mediterranean Sea is one of thelargest semi-enclosed seas. The marine flora and fauna are some of the richest in the world, relative to itssize, particularly in the coastal habitats, which are also characterized by numerous endemic speciesalthough the introduction of non-indigenous species threatens its rich and unique biodiversity. Followingthe opening of the Suez Canal, and in combination with shipping and aquaculture activities, nonindigenousspecies (NIS) introduction has had measurable impacts on the Mediterranean. Lagoon ecosystemsalong the French coastline, with approx. 100 NIS identified, are considered hot-spot areas forthese species. Rapid assessment sampling for sessile benthic species together with DNA barcoding is arapid, easy and cheap method to detect non-indigenous species. Two nearby and different ecosystemswere sampled for invertebrate species: Saint-Nazaire lagoon, a Special Protection Area within the Natura2000 Network and Canet port, a marina in a small village. The DNA barcoding tool for species identificationwas used for confirming the taxonomy. This showed that, despite the Saint-Nazaire Lagoonclassification within the Natura 2000 network, it is already contaminated with a single NIS that wasfound in high densities and is clearly beginning to dominate the system. It is proposed that a rapidassessment of the sampled environment and the DNA barcode approach are efficient and can providesufficient information on the new target species to be used in conservation planning and ongoingmanagement efforts.
ISSN: 0272-7714

hal-01488926
https://hal-univ-perp.archives-ouvertes.fr/hal-01488926
DOI : 10.1016/j.ecss.2017.02.004

Éditeur(s) : Gauthier-Villars
Résumé : The tropical alga Caulerpa taxifolia (Vahl) C. Agardh has been displayed over the last fifteen years in tropical aquaria at the Oceanographic Museum, Monaco. Its accidental introduction into the natural environment dates from 1984. It developed first in the sea immediately below the museum, and resisted winter temperatures of 11 to 13-degrees-C. Gradually the population spread over all types of substrate, including rock, sand and mud, and over a wide range of depth, 3 to 35 m, on this relatively exposed site. In summer 1990 we became aware of its presence both to the east and to the west of Monaco. To the east, it now occurs on the whole of the eastern side of Cap Martin (3 km from Monaco) and is spreading over the west face. To the west we have observed it 150 km from Monaco near Toulon. In those sites which it colonized three years ago, its coverage now reaches 100 % over extensive areas in depths between 5 and 25 m. Areas supporting stands of Cymodocea nodosa and Posidonia oceanica are covered by fronds of C. taxifolia, which measure up to 45 cm in length. The development characteristics of the species in the Mediterranean, such as population density and frond length, are different from those in its native tropical areas. The rapid spreading of this alga is probably due both to sexual reproduction and to efficient vegetative reproduction. At the rate of spreading observed at present, further rapid extension of its range is to be feared. Moreover, wherever it becomes established, it considerably modifies the vegetal communities in the infralittoral zone. This species, like most of those in the genus Caulerpa, contains the toxin, caulerpenyn, which may play a role against other organisms such as grazers, epiphytes and competitors. This alga will be eaten only by certain animals such as the Mediterranean bream or saupe, Sarpa salpa. The toxin accumulated by fish which eat Caulerpa can render them unsuitable for human consumption, as their ingestion produces symptoms similar to those of Ciguatera poisoning. Never has a species so potentially harmful to the marine population been introduced into the Mediterranean. This biological pollution raises the major international problem of direct discharge of water having passed through aquaria or mariculture installations containing exotic species. As importing exotic marine species becomes technically easier, the lack of regulation risks further similar accidents concerning not only algae, but also metazoa and micro-organisms.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1991 , Vol. 14 , N. 4 , P. 415-426

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00101/21268/18879.pdf
http://archimer.ifremer.fr/doc/00101/21268/

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
In this study we attempt to understand the water storage variations in a karst aquifer on the Larzac Plateau (South of France) using ground-based gravimetry. Surface to 60 m depth gravity measurements are performed three times a year since 2006 down a pothole, in complement to monthly absolute gravity (AG) measurements at three sites. The time variations of the surface to depth (STD) gravity differences are compared with the AG variations. Using a simple Bouguer plate model, we find that the STD gravity differences are very similar to the AG variations. The STD gravity differences are then used to determine apparent density values. These integrative density values are compared with measured grain densities from core samples to obtain an apparent porosity and saturation change representative of the investigated depth. The apparent porosity ranges from 4.8 to 7.3 per cent. We then discuss on the repartition of the apparent physical properties with respect to the epikarst and infiltration zone karst structures. We argue that AG and STD differences monitor epikarst water storage variations. Within this scope, we discuss the fact that seasonal scale water storage variation occurs predominantly in the epikarst.
ISSN: 0956-540X

hal-00413528
https://hal.archives-ouvertes.fr/hal-00413528
DOI : 10.1111/j.1365-246X.2009.04118.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This work focuses on the analysis of a unique set of seismological data recorded by two temporary networks of seismometers deployed onshore and offshore in the Central Lesser Antilles Island Arc from Martinique to Guadeloupe islands. During the whole recording period, extending from January to the end of August 2007, more than 1300 local seismic events were detected in this area. A subset of 769 earthquakes was located precisely by using HypoEllipse. We also computed focal mechanisms using P-wave polarities of the best azimuthally constrained earthquakes. We detected earthquakes beneath the Caribbean forearc and in the Atlantic oceanic plate as well. At depth seismicity delineates the Wadati-Benioff Zone down to 170 km depth. The main seismic activity is concentrated in the lower crust and in the mantle wedge, close to the island arc beneath an inner forearc domain in comparison to an outer forearc domain where little seismicity is observed. We propose that the difference of the seismicity beneath the inner and the outer forearc is related to a difference of crustal structure between the inner forearc interpreted as a dense, thick and rigid crustal block and the lighter and more flexible outer forearc. Seismicity is enhanced beneath the inner forearc because it likely increases the vertical stress applied to the subducting plate.
ISSN: 0040-1951

hal-01052679
https://hal.archives-ouvertes.fr/hal-01052679
DOI : 10.1016/j.tecto.2011.08.006

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Our knowledge and understanding of the 3-D lithospheric structure of the Himalayas and the Tibetan Plateau is still challenging although numerous geophysical studies have been performed in the region. The GOCE satellite mission has the ambitious goal of mapping Earth's gravity field with unprecedented precision (i.e. an accuracy of 1-2 mGal for a spatial resolution of 100 km) to observe the lithosphere and upper-mantle structure. Consequently, it gives new insights in the lithospheric structure beneath the Himalayas and the Tibetan Plateau. Indeed, the GOCE gravity data now allow us to develop a new strategy for joint gravimetry-seismology inversion. Combined with teleseismic data over a large region in a joint inversion scheme, they will lead to lithospheric velocity-density models constrained in two complementary ways. We apply this joint inversion scheme to the Hi-CLIMB (Himalayan-Tibetan Continental Lithosphere during Mountain Building) seismological network which was deployed in South Tibet and the Himalayas for a 3-yr period. The large size of the network, the high quality of the seismological data and the new GOCE gravity data set allow us to image the entire lithosphere of this active area in an innovative way. We image 3-D low velocity and density structures in the middle crust that fit the location of discontinuous low S-velocity zones revealed by receiver functions in previous geophysical studies. In the deeper parts of our velocity model we image a positive anomaly interpreted to be the heterogenous Indian lithosphere vertically descending beneath the centre of the Tibetan Plateau.
ISSN: 0956-540X

hal-00858024
https://hal.archives-ouvertes.fr/hal-00858024
DOI : 10.1093/gji/ggs110

Éditeur(s) : HAL CCSD
Résumé : For a decade, distance-based methods have been widely employed and constantly improved in the field of spatial economics. These methods are a very useful tool for accurately evaluating the spatial distribution of plants or retail stores, for example (Duranton and Overman, 2008). In this paper, we introduce a new distance-based statistical measure for evaluating the spatial concentration of economic activities. To our knowledge, the m function is the first relative density function to be proposed in the economics literature. This tool supplements the typology of distance-based methods recently drawn up by Marcon and Puech (2012). By considering several theoretical and empirical examples, we show the advantages and the limits of the m function for detecting spatial structures in economics.
https://hal.archives-ouvertes.fr/hal-01082178

hal-01082178
https://hal.archives-ouvertes.fr/hal-01082178
https://hal.archives-ouvertes.fr/hal-01082178v3/document
https://hal.archives-ouvertes.fr/hal-01082178/file/LANG-%20MARCON-PUECH%20-%20m%20-%20HAL%2001082178v3.pdf

Éditeur(s) : HAL CCSD American Society for Pharmacology and Experimental Therapeutics (ASPET)
Résumé : International audience
Most human hepatocyte cell lines lack a substantial set of liver-specific functions, especially major cytochrome P450 (P450)-related enzyme activities, making them unrepresentative of in vivo hepatocytes. We have used the HepaRG cells, derived from a human hepatocellular carcinoma, which exhibit a high differentiation pattern after 2 weeks at confluency to determine whether they could mimic human hepatocytes for drug metabolism and toxicity studies. We show that when passaged at low density, these cells reversed to an undifferentiated morphology, actively divided, and, after having reached confluency, formed typical hepatocyte-like colonies surrounded by biliary epithelial-like cells. By contrast, when seeded at high density, hepatocyte-like clusters retained their typical differentiated morphology. Transcripts of various nuclear receptors (aryl hydrocarbon receptor, pregnane X receptor, constitutive androstane receptor, peroxisome proliferator-activated receptor alpha), P450s (CYP1A2, 2C9, 2D6, 2E1, 3A4), phase 2 enzymes (UGT1A1, GSTA1, GSTA4, GSTM1), and other liver-specific functions were estimated by reverse transcriptase-quantitative polymerase chain reaction and were found to be expressed, for most of them, at comparable levels in both confluent differentiated and high-density differentiated HepaRG cells and in cultured primary human hepatocytes. For several transcripts, the levels were strongly increased in the presence of 2% dimethyl sulfoxide. Measurement of basal activities of several P450s and their response to prototypical inducers as well as analysis of metabolic profiles and cytotoxicity of several compounds confirmed the functional resemblance of HepaRG cells to primary cultured human hepatocytes. In conclusion, HepaRG cells constitute the first human hepatoma cell line expressing high levels of the major P450s involved in xenobiotic metabolism and represent a reliable surrogate to human hepatocytes for drug metabolism and toxicity studies.
ISSN: 0090-9556

hal-00702085
https://hal.archives-ouvertes.fr/hal-00702085
DOI : 10.1124/dmd.105.006759
PUBMED : 16204462

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wind energy production is very sensitive to turbulent wind speed. Thus rapid variation of wind speed due to changes in the local meteorological conditions can lead to electrical power variations of the order of the nominal power output, in particular when wind power variations on very short time scales, range at few seconds to 1 h, are considered. In small grid as they exist on islands (Guadeloupean Archipelago: French West Indies) such fluctuations can cause instabilities in case of intermediate power shortages. The developed analysis in [14] reveals three main classes of time series for the wind speed fluctuations. In this work, Probability Density Functions (PDFs) are proposed to fit the wind speed fluctuations distributions in each class. After, to simulate wind speed fluctuations sequences, we use a stochastic differential equation, the Langevin equation considering Gaussian turbulence PDF (class I), Gram–Charlier PDF (class II) and a mixture of gaussian PDF (class III). The statistical and dynamical properties of simulated wind sequences are close to those of measured wind sequences, for each class
ISSN: 0306-2619

hal-01527885
https://hal.archives-ouvertes.fr/hal-01527885
DOI : 10.1016/j.apenergy.2012.05.007

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : We examined tree-soil habitat associations in lowland forest communities at Paracou, French Guiana. We analyzed a large dataset assembling six permanent plots totaling 37.5 ha, in which extensive LIDAR-derived topographical data and soil chemical and physical data have been integrated with precise botanical determinations. Map of relative elevation from the nearest stream summarized both soil fertility and hydromorphic characteristics, with seasonally inundated bottomlands having higher soil phosphate content and base saturation, and plateaus having higher soil carbon, nitrogen and aluminum contents. We employed a statistical test of correlations between tree species density and environmental maps, by generating Monte Carlo simulations of random raster images that preserve autocorrelation of the original maps. Nearly three fourths of the 94 taxa with at least one stem per ha showed a significant correlation between tree density and relative elevation, revealing contrasted species-habitat associations in term of abundance, with seasonally inundated bottomlands (24.5% of species) and well-drained plateaus (48.9% of species). We also observed species preferences for environments with or without steep slopes (13.8% and 10.6%, respectively). We observed that closely-related species were frequently associated with different soil habitats in this region (70% of the 14 genera with congeneric species that have a significant association test) suggesting species-habitat associations have arisen multiple times in this tree community. We also tested if species with similar habitat preferences shared functional strategies. We found that seasonally inundated forest specialists tended to have smaller stature (maximum diameter) than species found on plateaus. Our results underline the importance of tree-soil habitat associations in structuring diverse communities at fine spatial scales and suggest that additional studies are needed to disentangle community assembly mechanisms related to dispersal limitation, biotic interactions and environmental filtering from species-habitat associations. Moreover, they provide a framework to generalize across tropical forest sites.
ISSN: 1932-6203

hal-01260289
https://hal.archives-ouvertes.fr/hal-01260289
PRODINRA : 342930
DOI : 10.1371/journal.pone.0141488

Éditeur(s) : HAL CCSD
Résumé : Among erosion processes, river incision is classicaly described as a key process controlling erosion of landscapes. Incision efficiency is mainly influenced by climate and erodibility. This latter is not only dependent on the nature of the bedrock, but also on its past deformation, which affects its rheological effective properties, such as fracture density. The main objectives of this thesis are: (1) to better constrain the relationship between effective properties and erodibility, and (2) to quantify the influence of erodibility and erosion on both the temporal and spatial building or decay of the topography. Several numerical tools are developed. A 1D formalism of landscape evolution is introduced, including river incision with stochastic distribution of water discharge and hillslope landsliding. A new remeshing algorithm called Surface Lagrangian Remeshing (SLR) is developed as a complement to remeshing algorithms dealing with internal elements. It allows one to take into account long-term erosion into 2D Lagrangian numerical codes based on triangular finite elements. Then the potentiality of measuring erodibility in-situ using a Schmidt hammer (R) is assessed for the active orogen of Taiwan, the diagenetic Annot sandstones and St Clement fault zone. Results suggest a strong control of R by effective properties. A linear model based on effective medium theory is applied to a fault zone with an unmacthed resolution (750 measures, 25 measures per square meter). The model successfully correlates R to fracture density. These results demonstrate that effective elasticity as well as erodibility are sensitive to the density and type of fractures. Finally I focus on the erosional and rheological conditions that allows reproducing post-orogenic evolution of mountain belts. A model coupling surface erosion and regional isostatic uplift is consistent with observations. The topographic decay and decrease of the ratio of surface elevation over crustal root thickness is at first order controlled by the initial geometry of the mountain belt and erosion efficiency. This new model highlights the control ofclimate and erodibility on the topographic decay and of lithospheric rheology on the perseverance of crustal roots.
Parmi les processus d'érosion, l'incision des rivières est classiquement décrit comme un processus clé contrôlant l'érosion des paysages. L'efficacité de l'incision est principalement influencée par le climat et par l'érodabilité. Ce dernier paramètre ne dépend pas seulement de la nature du substratum rocheux, mais aussi de sa déformation passée qui affecte ses propriétés rhéologiques équivalentes. Les principaux objectifs de cette thèse sont: (1) de mieux contraindre les relations entre propriétés équivalentes et érodabilité, et (2) de quantifier l'influence de l'érosion et de l'érodabilité sur la formation ou la décadence, spatiale et temporelle, de la topographie. Plusieurs outils numériques sont développés. Un formalisme 1D d'évolution des paysages est proposé, prenant en compte simultanément l'incision des rivières avec une distribution stochastique des débits en eau et l'érosion des versants par glissements de terrain. Un nouvel algorithme de remaillage appelé Surface Lagrangian Remeshing (SLR) est développé. Il permet de prendre en compte l'érosion à long terme dans les codes numériques 2D Lagrangiens basés sur des éléments finis triangulaires. Ensuite, la possibilité de mesurer in-situ l'érodabilité avec un marteau de Schmidt (R) est évaluée pour: l'orogène actif de Taiwan, les grès diagénétiques d'Annot et la zone de faille de St Clément. Les résultats suggèrent un fort contrôle de R par les propriétés équivalentes des roches testées. Un modèle linéaire, basé sur la théorie des milieux équivalents, est appliqué à une zone de faille avec une résolution inégalée (750 mesures, 25 mesures par mètre carré). Le modèle permet de corréler avec succès la densité de fracture et R. Ces résultats démontrent empiriquement que l'élasticité équivalente ainsi que l'érodabilité sont sensibles à la densité et à la nature des fractures. Enfin j'étudie les conditions d'érosion et de rhéologie qui permettent de reproduire l'évolution des chaînes de montagnes post-orogéniques. Un modèle couplant érosion en surface et soulèvement isostatique régional est compatible avec les observations. Les taux de décroissance topographique et de diminution du rapport de l'élévation de surface sur l'épaisseur de racine crustale sont contrôlés au premier ordre par la géométrie initiale de la chaîne de montagne et par l'efficacité de l'érosion. Ce nouveau modèle met en évidence le contrôle du climat et de l'érodabilité sur la décroissance topographique et de la rhéologie lithosphérique sur la persévérance des racines crustales.
https://tel.archives-ouvertes.fr/tel-00602341

tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341/document
https://tel.archives-ouvertes.fr/tel-00602341/file/thesephilippesteer.pdf