Éditeur(s) : HAL CCSD
Résumé : Ocean Drilling Program Hole 1256D reached for the first time the transition zone between the sheeted dike complex and the uppermost gabbros. The recovered crustal section offers a unique opportunity to study the deepest part of the hydrothermal system in present-day oceanic crust. We present a structural analysis of electrical borehole wall images. We identified, and measured the orientations of four categories of structures: major faults, minor fractures, possibly hydrothermal veins, and dikes. All structures tend to strike parallel to the paleo-ridge axis. Three major fault zones (meter thick) and dikes are steeply dipping (~ 75° on average) outward the ridge. Centimeter-thick moderately conductive planar features are interpreted as hydrothermal veins, are organized in arrays of consistent spacing, thickness, and orientation, and are dipping about 15-20° toward the ridge. This structural pattern is interpreted as an on-axis paleohydrothermal circulation system, with vertical, dike-parallel fractures, and sub-horizontal high-temperature hydrothermal veins at the base of the sheeted dike, which was subsequently rotated ~ 15° westward around a ridge-parallel, sub-horizontal axis. This rotation can be caused by upper-crustal block rotation along a listric normal fault, and/or subsidence at the ridge axis.
Ofioliti

hal-00757592
https://hal.archives-ouvertes.fr/hal-00757592
DOI : 10.4454/ofioliti.v37i1.402

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Although magmatism may occur during the earliest stages of continental rifting, its role in strain accommodation remains weakly constrained by largely 2-D studies. We analyze seismicity data from a 13 month, 39-station broadband seismic array to determine the role of magma intrusion on state-of-stress and strain localization, and their along-strike variations. Precise earthquake locations using cluster analyses and a new 3-D velocity model reveal lower crustal earthquakes beneath the central basins and along projections of steep border faults that degas CO2. Seismicity forms several disks interpreted as sills at 6-10 km below a monogenetic cone field. The sills overlie a lower crustal magma chamber that may feed eruptions at Oldoinyo Lengai volcano. After determining a new ML scaling relation, we determine a b-value of 0.87±0.03. Focal mechanisms for 65 earthquakes, and 13 from a catalogue prior to our array reveal an along-axis stress rotation of ∼60° in the magmatically active zone. New and prior mechanisms show predominantly normal slip along steep nodal planes, with extension directions ∼N90°E north and south of an active volcanic chain consistent with geodetic data, and ∼N150°E in the volcanic chain. The stress rotation facilitates strain transfer from border fault systems, the locus of early-stage deformation, to the zone of magma intrusion in the central rift. Our seismic, structural, and geochemistry results indicate that frequent lower crustal earthquakes are promoted by elevated pore pressures from volatile degassing along border faults, and hydraulic fracture around the margins of magma bodies. Results indicate that earthquakes are largely driven by stress state around inflating magma bodies.
ISSN: 1525-2027

hal-01667198
https://hal.archives-ouvertes.fr/hal-01667198
DOI : 10.1002/2017GC007027

Éditeur(s) : Elsevier Science Bv
Résumé : Fluid escape structures on the Nile Deep Sea Fan were investigated during the MEDIFLUX MIMES expedition in 2004. Mud volcanoes, pockmarks and authigenic carbonate structures were surveyed for the first time with a high-resolution deep-towed 75 kHz sidescan sonar and a 2-8 kHz Chirp sediment echosounder. In combination with existing multibeam bathymetry and detailed seafloor in situ geological observations, these new data allowed detailed seep analyses. About 60 gas flares were detected acoustically in the water column from the sidescan sonar raw data at water depths from 770 to 1700 m. These gas flares coincide at the seabed with 1) the centres of the mud volcanoes where mud is also extruded, 2) the borders of the mud volcanoes where the emitted gases contribute to the precipitation of authigenic carbonates, and 3) to the edges of broad sheets of authigenic carbonates. Subsurface sediments are commonly disturbed by ascending fluids throughout the delta, with an abundance of seep-related carbonate structures on the seafloor. The feeder channels below mud volcanoes, similar to the gas conduits below the widespread carbonate crust structures and pockmarks, are relatively narrow and, for the vast majority of them, do not exceed a few metres in diameter. The seeps on the Nile Deep Sea Fan clearly follow lineations on the seafloor that we can relate to faults. (C) 2010 Elsevier B.V. All rights reserved.
Marine Geology (0025-3227) (Elsevier Science Bv), 2010-09 , Vol. 275 , N. 1-4 , P. 1-19

Droits : 2010 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00013/12457/9766.pdf
DOI:10.1016/j.margeo.2010.04.003
http://archimer.ifremer.fr/doc/00013/12457/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Geodetic data support a short-term continental deformation localized in faults bounding lithospheric blocks. Whether major "faults" observed at the surface affect the lithospheric mantle and, if so, how strain is distributed are major issues for understanding the mechanical behavior of lithospheric plates. A variety of evidence, from direct observations of deformed peridotites in orogenic massifs, ophiolites, and mantle xenoliths to seismic reflectors and seismic anisotropy beneath major fault zones, consistently supports prolongation of major faults into the lithospheric mantle. This review highlights that many aspects of the lithospheric mantle deformation remain however poorly understood. Coupling between deformation in frictional faults in the uppermost crust and localized shearing in the ductile crust and mantle is required to explain the post-seismic deformation, but mantle viscosities deduced from geodetic data and extrapolated from laboratory experiments are only reconciled if temperatures in the shallow lithospheric mantle are high (> 800 °C at the Moho). Seismic anisotropy, especially shear wave splitting, provides strong evidence for coherent deformation over domains several tens of km wide in the lithospheric mantle beneath major transcurrent faults. Yet it cannot detect narrow strain localization zones or shallowly dipping faults. Seismic profiling images shallow-dipping seismic reflectors in the lithospheric mantle interpreted as the continuation of normal or, less frequently, inverse faults in the mantle. However the nature of these reflectors is poorly understood. There is a large discrepancy between the scale at which deformation processes are studied (a few kilometers, at most, due to the limited size of continuous mantle exposures at the Earth's surface) and the scale inferred for strain localization in the mantle from geophysical observations (tens of kilometers). Combining data on deformation microstructures and crystal preferred orientations in naturally deformed peridotites and seismologic observations allows nevertheless discussing strain localization processes that may play a role on the development of mantle shear zones.
ISSN: 0040-1951

hal-00750314
https://hal.archives-ouvertes.fr/hal-00750314
DOI : 10.1016/j.tecto.2012.06.006

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
The variation of elastic- wave velocities as a function of the direction of propagation through the Earth's interior is a widely documented phenomenon called seismic anisotropy. The geometry and amount of seismic anisotropy is generally estimated by measuring shearwave splitting, which consists of determining the polarization direction of the fast shear- wave component and the time delay between the fast and slow, orthogonally polarized, waves. In subduction zones, the teleseismic fast shear- wave component is oriented generally parallel to the strike of the trench(1), although a few exceptions have been reported (Cascadia(2) and restricted areas of South America(3,4)). The interpretation of shear- wave splitting above subduction zones has been controversial and none of the inferred models seems to be sufficiently complete to explain the entire range of anisotropic patterns registered worldwide(1). Here we show that the amount and the geometry of seismic anisotropies measured in the forearc regions of subduction zones strongly depend on the preferred orientation of hydrated faults in the subducting oceanic plate. The anisotropy originates from the crystallographic preferred orientation of highly anisotropic hydrous minerals (serpentine and talc) formed along steeply dipping faults and from the larger- scale vertical layering consisting of dry and hydrated crust - mantle sections whose spacing is several times smaller than teleseismic wavelengths. Fault orientations and estimated delay times are consistent with the observed shear- wave splitting patterns in most subduction zones.
ISSN: 0028-0836

hal-00412016
https://hal.archives-ouvertes.fr/hal-00412016
DOI : 10.1038/nature07376

Éditeur(s) : American Geophysical Union
Résumé : We use seismic reflection and rock sample data to propose that the first-order physiography of New Caledonia Trough and Norfolk Ridge formed in Eocene and Oligocene time and was associated with the onset of subduction and back-arc spreading at the Australia-Pacific plate boundary. Our tectonic model involves an initial Cretaceous rift that is strongly modified by Cenozoic subduction initiation. Hence, we are able to explain (1) complex sedimentary basins of inferred Mesozoic age; (2) a prominent unconformity and onlap surface of middle Eocene to early Miocene age at the base of flat-lying sediments beneath the axis of New Caledonia Trough; (3) gently dipping, variable thickness, and locally deformed Late Cretaceous strata along the margins of the trough; (4) platform morphology and unconformities on either side of the trough that indicate a phase of late Eocene to early Miocene uplift to near sea level, followed by rapid Oligocene and Miocene subsidence of similar to 1100-1800 m; and (5) seismic reflection facies tied to boreholes that suggest absolute tectonic subsidence at the southern end of New Caledonia Trough by 1800-2200 m since Eocene time. The Cenozoic part of the model involves delamination and subduction initiation followed by rapid foundering and rollback of the slab. This created a deep (>2 km) enclosed oceanic trough, similar to 2000 km long and 200-300 km across, in Eocene and Oligocene time as the lower crust detached, with simultaneous uplift and local land development along basin flanks. Disruption of Late Cretaceous and Paleogene strata was minimal during this Cenozoic phase and involved only subtle tilting and local reverse faulting or folding. Basin formation was possible through the action of at least one detachment fault that allowed the lower crust to either be subducted into the mantle or exhumed eastward into Norfolk Basin. We suggest that delamination of the lithosphere, with possible mixing of the lower crust back into the mantle, is more widespread than previously thought and may be commonly associated with subduction initiation, such as Cenozoic events in the Mediterranean and western Pacific.
Tectonics (0278-7407) (American Geophysical Union), 2010-03 , Vol. 29 , N. TC2004 , P. 1-16

Droits : Copyright 2010 by the American Geophysical Union.
http://archimer.ifremer.fr/doc/00001/11271/9283.pdf
DOI:10.1029/2009TC002476
http://archimer.ifremer.fr/doc/00001/11271/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We use 36Cl surface exposure dating to determine the slip release pattern over the last ~ 15 kyr for the Velino-Magnola fault, a major active normal fault in Central Italy. We sampled the fault at five well-separated sites along its length, and modeled the 36Cl concentrations measured in the 376 samples. We find that the fault broke in at least 9 large earthquakes that occurred in two 5-6 ka-long supercycles. Each cycle included a 4-5 ka-long phase of relative quiescence, followed by a cluster of at least 3 large earthquakes or earthquake sequences that released most of the accumulated strain in ~ 1 ka. All 9 identified events broke the entire fault and produced maximum surface slips of 2-3 m. Though the Velino-Magnola fault seems presently in a stage of relative quiescence, it may re-enter a phase of paroxysmal seismic activity in a few hundred of years
ISSN: 0012-821X

hal-00667280
https://hal.archives-ouvertes.fr/hal-00667280
DOI : 10.1016/j.epsl.2011.05.022

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In orogenic systems, thrust faults play a major role in stacking different tectonic units and may act as conduits for the expulsion of large amounts of fluid of different origins (metamorphic, diagenetic, meteoric). This study focuses on the Monte Perdido thrust unit emplaced in the Paleogene Jaca thrust-sheet-top basin, in the SW-central Pyrenees. We aim to decipher the mechanisms and P-T conditions of deformation in fault zones and characterize the related fluid involvement, through combined microstructural, geochemical and microthermometry analyses. Two thrust faults cutting platform limestones, marls and siliciclastic turbidites of the lower part of the basin-fill (Paleocene-lower Eocene) have been studied. The fault zones are characterized by metre-thick shear zones with highly deformed, foliated clay-rich sediments. Foliation is underlined by preferentially oriented phyllosilicates. Several generations of shear and extension calcite, quartz and chlorite-bearing veins attest to fluid-rock interactions during a multi-stage deformation. Microstructural observations and stable isotope analyses on calcite from veins and host sediments suggest that deformation was aseismic and dominated by diffusive mass transfer from pressure solution sites along cleavage and stylolites to the precipitation sites in veins, with mineralizing fluids in equilibrium with the host sediments. Our results suggest an essentially closed hydrologic system, and imply the absence of significant fluid flow along the studied fault zones. Microthermometric study on fluid inclusions present in calcite and quartz veins, and calcite-quartz oxygen isotopic fractionation determined for the first generation shear veins, allow a geothermal gradient of 34 degrees C/km to be estimated. Analytical results demonstrate an evolution of the fault zones in three stages. The first stage was related to the emplacement of the Monte Perdido thrust unit during the middle Eocene at a temperature of similar to 208 degrees C and a burial depth of similar to 5.7 km. The second stage corresponds to a fault reactivation at a temperature of similar to 240 degrees C and a burial depth of similar to 6.5 km. The latter deformation may have been related to folding of the Monte Perdido thrust unit during the emplacement of the underlying Gavarnie thrust unit during the late Eocene-early Oligocene, with deeper burial resulting from aggradation of the thrust-sheet-top basin-fill. The last event corresponds to the formation of a dilatant vein system likely related to the exhumation of the massif.
ISSN: 0191-8141

hal-00644828
https://hal.archives-ouvertes.fr/hal-00644828
DOI : 10.1016/j.jsg.2011.06.006

Éditeur(s) : HAL CCSD Geological Society
Résumé : Extensional basins often evolve both with the generation of normal faults at all scales, and with tilting in the hanging walls and footwalls of major structures. This paper examines the effect of regional tilting on the development of normal fault arrays in an anisotropic sequence, using the asymmetric Lodève Basin, France, as a case study. The orientation range of normal faults is found not to match that expected by continued symmetric generation of conjugate normal faults during tilting. Instead, continued generation of new faults preferentially occurred for faults dipping opposite to the direction of tilt, with propagation perpendicular to bedding. The presence of early bedding-perpendicular joints in the competent sandstone units aided propagation of these faults during tilting and this preferential asymmetric development. Bedding-parallel slip surfaces were activated as normal faults during the later stages of bedding tilting, showing complex interaction patterns with later faults downthrowing in the direction opposite to bedding tilting. Hence knowledge of the timing between tilting of the strata and deformation helps in evaluating the likely complexity of fault arrays at subseismic scales in extensional basins, and may also help in understanding the evolution of fault systems in tilted normal fault blocks at the reservoir scale.
ISSN: 0016-7649

hal-00404753
https://hal.archives-ouvertes.fr/hal-00404753
DOI : 10.1144/0016-76492006-047

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The North Tehran Fault (NTF) is located at the southernmost piedmont of Central Alborz and crosses the northern suburbs of the Tehran metropolis and adjacent cities, where ∼15 million people live. Extending over a length of about 110 km, the NTF stands out as a major active fault and represents an important seismic hazard for the Iranian capital after historical seismicity. In order to characterize the activity of the NTF in terms of kinematics, magnitude and recurrence intervals of earthquakes, we carried out a first paleoseismological study of the fault within its central part between Tehran and Karaj cities. We opened a trench across a 3 m-high fault scarp affecting Quaternary deposits. Our study shows that the scarp is the result of repeated events along a main N115°E trending shallow dipping thrust fault, associated with secondary ruptures. From the trench analysis and Infrared Stimulated Luminescence (IRSL) dating of fault-related sediments, we interpreted between 6 and 7 surface-rupturing events that occurred during the past 30 kyrs. Their magnitudes (estimated from the displacements along the faults) are comprised between 6.1 and 7.2. The two last events - the largest - occurred during the past 7.9 ± 1.2 ka, which yields a Holocene slip rate of ∼0.3 mm/yr. The 7 earthquakes scenario suggests a regular periodicity with a mean recurrence interval of ∼3.8 kyrs. However, the two most recent events could correspond to the two largest historical earthquakes recorded in the area (in 312-280 B.C. and 1177 A.D.), and therefore suggest that the NTF activity is not regular.
ISSN: 0148-0227

hal-00757568
https://hal.archives-ouvertes.fr/hal-00757568
https://hal.archives-ouvertes.fr/hal-00757568v2/document
https://hal.archives-ouvertes.fr/hal-00757568/file/ritz2012.pdf
DOI : 10.1029/2012JB009147

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : Normal faulting mechanisms observed in the northern foothills of the Central–Western Pyrenees are remarkable, since one expects thrust faults at a convergent plate boundary. To understand the mechanisms involved, we used numerical modeling and investigated the impact of the following processes: gravitational potential energy associated with topography and dense crustal blocks; isostatic compensation in response to denudation and/or sedimentation. To decipher the effects of each process, we designed three model geometries and added a pre-existing weak fault where most of the seismicity occurs. To evaluate our model results, we derived the fault slip rate from the focal mechanisms in the region where we have the fault in our model. We found a slip rate of ∼15 m/Ma, which is in agreement with our modelling results. We conclude that flexural rebound induced by surface processes is able to explain the seismicity in Central–Western Pyrenees.
ISSN: 1631-0713

hal-01346028
https://hal.archives-ouvertes.fr/hal-01346028
https://hal.archives-ouvertes.fr/hal-01346028/document
https://hal.archives-ouvertes.fr/hal-01346028/file/Genti.pdf
DOI : 10.1016/j.crte.2015.08.004

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
This paper presents a synthesis of a multidisciplinary study carried out along the Nîmes Roman aqueduct, located in the southeast part of France. The study was motivated by archaeologists attempting to explain the partial destructions of only one aerial bridge of the aqueduct (Pont de la Lône). Given its close proximity to the Nîmes seismically active fault, a possible seismic origin for the destructions was invoked. Seismologists and structural engineers thus carried out a variety of field and numerical investigations to test the seismic hypothesis. Supporting field evidence was found first along the aerial bridge section of the aqueduct: broken stalactites, arch warping, cracks and destruction of the bridge just above a breast wall shortly after its construction. Secondly, the underground part of the canal was analysed: irregularity in the thickness of calcite deposits of the canal walls, presence of numerous cracks, horizontal shift of the otherwise linear structure of the canal and presence of calcite twins in the deposits, found only where the canal crosses the Nîmes fault system. Numerical modelling and experimental results show that (1) only the Pont de la Lône would have suffered serious damage under seismic solicitation (assuming an M6 earthquake at 10 km distance). The second aerial bridge, the three levels arches Pont du Gard, an historical monument still standing today, would have suffered less damage, due to its very different fundamental frequency of around 0.4 Hz, far from the amplified seismic near-field spectrum; (2) the numerical models also show that a fall of the canal wall would require a higher magnitude event (M > 6); (3) the presence of calcite twinning requires a differential static stress of 4 MPa or greater, which can only be achieved very close to the fault rupture of a M > 6 earthquake; (4) finally, local surface rupturing of such a fault would also corroborate the hypothesis that the observed offset of the canal may be partly seismically induced. Although other possible origins for each individual evidence may not be excluded, the observed spatiotemporal concentration of architectural/geological anomalies together with the numerical results allow us to support a possible co-seismic origin for these disorders, indirectly attesting to the potential seismic activity (M > 6) of the nearby Nîmes fault. Furthermore, following the conclusions of archaeological studies, the disorders occurred between 250 and 350 year AD, thus providing timing for this possible seismic event, an essential parameter in seismic hazard analysis. These results validate the archaeo-seismological approach as a tool that may help improve the knowledge of major infrequent earthquakes in areas of moderate seismic activity.
ISSN: 0921-030X

hal-00379064
https://hal.archives-ouvertes.fr/hal-00379064
DOI : 10.1007/s11069-008-9276-9

Éditeur(s) : HAL CCSD
Résumé : When the upper crust below the mountain ranges shows crustal extension with a direction collinear to the convergence direction, it is generally accepted that it is the result of gravitational collapse. However, recent studies challenge this paradigm by showing that erosion induces uplift and extension in the central part of the low convergent mountain ranges. In this study, we investigate the impact of denudation on the seismotectonic regime of mountain ranges.In order to identify a relationship between seismotectonic regime and erosion, the first part of this work presents a compilation of data in the mountain ranges. Based on these observations, a simple kinematic model is proposed to predict the seismotectonic regime of the study ranges.For low convergence rate and moderate mean elevation ranges, this model predicts an extension regime when the denudation rate is 15% higher than the convergence rate.The second part is devoted to the development of thermomechanical 2D finite element models to study the impact of surface processes on the deformation of the Pyrenees. The results show that the isostatic response to erosion reactivates pre-existing structures. The kinematics of an inherited fault plane can be predicted due to the gradient of the horizontal surface velocity profile. Thus, a plane located in the eroded zone is reactivated in normal fault when near the border of the erosion area, this same plane is reactivated in reverse fault. These results suggest that the current deformation in the North Pyrenean Zone could be the result of surface processes.Given the small number of studies quantifying erosion rates in the Pyrenees, the models developed in the second part suffer from high uncertainty. To remedy this, we study the central Pyrenees through a study that combines two types of data : watershed denudation rates from cosmogenic isotopes concentration, and incision rates from sediments buried in the karst. These results are presented in chapter 3. Denudation profiles obtained are consistent with reactivation of a normal fault plane located in the North Zone of the Central Pyrenees.From our study in the Pyrenees, a good correlation appears between the value of the rate of erosion and the glacier occupation. Given that the glaciers where more developed in the Alps, it raises the question of the impact of the late-würmian deglaciation on the present deformation of this range. A numerical model detailing this relationship is presented in the fourth chapter. Theresults show that deglaciation of the western Alps is controlled by the rheological heterogeneity of the crust. Some of our models predict uplift rates consistent with those highlighted by geodesy.
Lorsque l’extension de la croûte sous les parties hautes des chaînes de montagnes est colinéaire à la direction de convergence, il est traditionnellement admis que le moteur est l’effondrement gravitaire. Pourtant, des études récentes remettent en cause ce paradigme en montrant que l’érosion induit un soulèvement et de l’extension dans la partie centrale des chaînes de montagne à faible taux de convergence. L’objectif de notre étude est d’étudier l’impact de la dénudation de la topographie sur le régime sismo-tectonique des chaînes de montagnes.La première partie de ce travail présente une compilation de données dans les chaînes de montagnes afin de dégager des relations entre régime sismo-tectonique et érosion. Sur la base de ces observations, un modèle cinématique simple permettant de prévoir le régime de la chaîne est proposé. Ainsi, pour les chaînes à faible taux de convergence et d’élévation moyenne, ce modèleprédit de l’extension lorsque le taux de dénudation est 15% plus élevé que le taux de convergence.La deuxième partie est consacrée au développement d’un modèle thermo-mécanique 2D en éléments finis pour étudier l’impact des processus de surface sur la déformation des Pyrénées.Les résultats montrent que la réponse isostatique à l’érosion permet de réactiver des structurespré-existantes. La cinématique d’un plan de faille hérité peut être prédite grâce au gradient du profil des vitesses de surface horizontales. Ainsi, un plan situé dans la zone d’érosion est réactivé en faille normale alors qu’en bordure de cette zone une faille est réactivée en régime inverse. Ces résultats suggèrent que la déformation actuelle des Pyrénées pourrait être la conséquence d’unprocessus d’érosion.Compte tenu du faible nombre d’études quantifiant les taux d’érosion dans les Pyrénées, les modèles développés dans la deuxième partie souffrent d’une forte incertitude. Pour y remédier, nous avons cherché à les quantifier dans les Pyrénées Centrales grâce à une étude qui combine deux types de données : taux de dénudation des bassins versants à partir des isotopes cosmogéniques, et vitesses d’incision à partir des sédiments piégés dans les karsts. Ces résultats sontprésentés dans la troisième partie. Les profils de dénudation obtenus sont compatibles avec unrejeu en faille normale d’un plan situé dans la Zone Nord Pyrénéenne des Pyrénées Centrales.Notre étude dans les Pyrénées, montre une bonne corrélation entre la valeur du taux d’érosion et la cartographie de l’occupation glaciaire. Les glaciers ayant été plus développés dans les Alpes, cela pose la question de l’impact de la déglaciation tardi-Wurmienne sur la déformation actuelle de cette chaîne. Un modèle numérique détaillant cette relation est présenté dans le quatrième chapitre. Les résultats montrent que la déglaciation des Alpes occidentales est contrôléepar l’hétérogénéité rhéologique de la croute. Certains de nos modèles prédisent des vitesses de surrection compatibles avec celles mises en évidence par la géodésie.
https://hal.archives-ouvertes.fr/tel-01262333

tel-01262333
https://hal.archives-ouvertes.fr/tel-01262333
https://hal.archives-ouvertes.fr/tel-01262333/document
https://hal.archives-ouvertes.fr/tel-01262333/file/these-Genti-2015-postjury.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Parentis and Arzacq-Mauleon basins located in front of the V-shaped oceanic propagator in the Bay of Biscay present evidence for extreme crustal thinning. In this paper we investigate the 3D structure of these rift basins, based on field observations and the interpretation of seismic data. We compare these results with those obtained from two different and independent inversion methods: first a 3D gravity inversion and second the standard Euler deconvolution.;For the Mauleon Basin our results show that the positive gravimetric anomaly identified above its southern margin is the consequence of two shallower high density bodies that are separated by the Pamplona fault and a deeper high density body. The high density bodies can be explained by the presence of mid-crustal and mantle rocks that were exhumed or uplifted at shallower depth during Early Cretaceous rifting before they were reworked and integrated to the Pyrenean chain during compression phase. Also, during this reactivation phase, some slices of the exhumed mid-crustal and mantle rocks were sheared off and were integrated in the present-day thrust belt in the Mauleon basin. For the Parentis Basin we can demonstrate, based on seismic data and gravimetric inversion methods, a decrease in extension from west to east, which is compatible with the V-shape geometry of the overall basin. Along strike, a change in the fault geometry from downward concave top-basement detachment faults to upward concave high-angle faults can be observed eastwards, i.e. towards the termination of the basin. A key structure, controlling the evolution of the Parentis Basin, is the east-west trending Ibis fault. We interpret this fault to have initially formed as a strike slip fault before it was reactivated during later crustal thinning. At present, it forms the limit between an upper plate sag basin to the north and a lower plate sag basin, floored at least locally by a top-basement detachment faults to the south. The strong asymmetry of the basin is supported by the shape of the basin and the results of standard Euler deconvolution.
ISSN: 0040-1951

hal-00523444
https://hal.archives-ouvertes.fr/hal-00523444
DOI : 10.1016/j.tecto.2010.04.023

Éditeur(s) : Wiley / Blackwell
Résumé : P>New seismic reflection data from the Grand Banks of Newfoundland and the Newfoundland Basin add to the growing knowledge of the composition, structure and history of this non-volcanic margin. Geophysical imaging is now approaching the extent of that done previously on the conjugate margin along Iberia, providing a valuable database for the development of rifting models. Two parallel profiles over the shelf platform image deep crustal fabric representing Precambrian or possibly Appalachian deformation as well as Mesozoic extension. Progressively more intense extension of continental crust is imaged oceanwards without the highly reflective detachments frequently seen on profiles off Galicia. A landward-dipping event 'L' is imaged sporadically and appears to be analogous to a similar event on the Iberian IAM9 profile. The transition zone is probably exposed serpentinized mantle as interpreted off the Iberian margin although there appears to be a difference in the character of ridge development and reflectivity. The distinctive 'U' reflection identified previously at the base of the Newfoundland Basin deep water sedimentary section and recently identified as one or more thin basalt sills is imaged on newly presented profiles that connect previously published profiles SCR3 and SCR2 showing that 'U' is highly regular and continuous except where interrupted by basement highs. 'U' is also seen to have a major impact on the ability to image underlying basement. A full transect beginning over completely unextended continental crust through to oceanic crust has provided a data set from which estimates of extension and the pre-rifting location of the present continental edge can be made. Two estimates were obtained; 85 km based on faulting and 120 km based on crustal thickness.
Geophysical Journal International (0956-540X) (Wiley / Blackwell), 2009-08 , Vol. 178 , N. 2 , P. 1004-1020

Droits : 2009 Wiley / Blackwell
http://archimer.ifremer.fr/doc/2009/publication-6919.pdf
DOI:10.1111/j.1365-246X.2009.04162.x
http://archimer.ifremer.fr/doc/00000/6919/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We develop a block model for the Aegean and surrounding areas, constrained by Global Positioning System (GPS), in order to investigate the degree of coupling on the Hellenic subduction interface (i.e., the fraction of the motion across the plate boundary accommodated by elastic strain accumulation). We use previously published models, and seismicity to define the geometry of the interface separating the down-going Nubian slab from the overriding Aegean. This model provides a good fit to the GPS observations; for the ∼200,000 km2 Aegean block the wrms of the residual velocities is 1.4 mm/yr for 80 GPS velocity estimates, approximately the 95% level of the GPS velocity uncertainties. We investigate the degree of coupling on the seismically active plate interface, the Hellenic trench splay fault (believed to be the source of the 365 AD Great Crete Earthquake and Tsunami), and the Kephalonia transform fault by comparing the modeled GPS residual velocity field for a range of coupling values. The GPS observations are almost insensitive to coupling on the Kephalonia transform fault, because of the vertical dip of the fault that creates interseismic deformation only close to the fault where few GPS sites exist. The absence of resolvable shortening of the leading edge of the Aegean Plate precludes coupling of more than 0.2 (20% of the full Nubia-Aegean convergence rate) on the modeled plate interface. Because of the shallow dip of the plate interface and trench splay fault, and high rate of convergence, if these boundaries were fully coupled, high elastic strain rates would be expected to extend well into the overriding Aegean plate. Based on our preferred value for the degree of coupling (0.1), and assuming characteristic earthquake behavior, we estimate a recurrence time for great earthquakes with slip similar to that for the 365 Crete event of 5700-8300 yr, consistent with the absence of subsequent great earthquakes on this segment of the subduction zone.
ISSN: 0012-821X

hal-01053486
https://hal.archives-ouvertes.fr/hal-01053486
DOI : 10.1016/j.epsl.2013.10.018

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
The 2004 Aceh and 2005 Nias events are the two greatest earthquakes of the past 40 years with a total rupture of 1700 km long and a coseismic slip reaching up to 25 m. These two earthquakes have caused large stress perturbations which significantly altered seismic activity in the Sumatra-Andaman region. Using both detailed mapping of failure planes and various slip distributions, we calculate this stress change along the Sumatra-Andaman-Sagaing fault system from central Sumatra to southern Myanmar. The static Coulomb stress change Delta CFF and the observed seismic activity are in very good agreement with a Coulomb index similar to 20% greater than the one obtained for random events. Compared to previous studies, this high Coulomb Index confirms two important issues on the use of static stress change criterion: unsuited to study near-field aftershocks and only relevant for aftershocks analysis on large and mature faults at a time scale of several months. The calculated Delta CFF distribution suggests that the 2004 and 2005 earthquakes inhibit failure on the North Andaman rift and on the Sagaing fault, while failure is encouraged along the transform Andaman zone, the central Andaman rift, the West Andaman fault, the Sumatra fault system, and the offshore thrust faults west of Sumatra Island. The maximum value of similar to 15-20 bar (1.5-2 MPa) for Delta CFF is reached in the northern part of the Sumatra fault system. This high value together with the lack of major earthquake in the last 170 years result in a high seismic hazard for this region. Our results are also consistent with temporal evolution of both earthquakes' location and focal mechanism prior to and after the events. In particular, we explain the occurrence and the mechanism of seismic swarms observed in the central Andaman rift and along the west Andaman fault. Finally, our calculations reveal that the seismicity in the Andaman rift zone can only be explained if mu' > 0.5. This result leads to two end-member models: one with a constant and high fault friction and one with spatial variations, for which friction may depend on either the nature of the lithosphere (oceanic versus continental) or the fault type.
ISSN: 1525-2027

hal-00456027
https://hal.archives-ouvertes.fr/hal-00456027
DOI : 10.1029/2008GC002167

Éditeur(s) : HAL CCSD
Résumé : International audience
South-east Iran is the site of a rare case of young transition between subduction and collision. We synthesized recent results in geodesy, tectonics, seismology and magnetism to understand the structure and kinematics of the Zagros-Makran transition. Surface observations (tectonics, magnetism and geodesy) draw a transpressive discontinuity consisting of several faults striking obliquely to the convergent plate motion, whereas deeper observations (seismology) support a smooth transition across the fault system. No lithospheric transform fault has been created, even though the transition already behaves like a major boundary in terms of tectonic style, seismic structure, lithology and magnetism. The Zendan-Minab-Palami fault system consists of several faults that accommodate a transpressive tectonic regime. It is the surface expression of a southward propagation of the N-trending right-lateral strike-slip fault system of Jiroft-Sabzevaran. Within each system the numerous faults will coalesce into a single, lithospheric, wrench fault.
ISSN: 0375-6440

hal-00356532
https://hal.archives-ouvertes.fr/hal-00356532
https://hal.archives-ouvertes.fr/hal-00356532/document
https://hal.archives-ouvertes.fr/hal-00356532/file/Regard_MinabSynthese_revised_AvecFigs.pdf
DOI : 10.1144/SP330.4

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Iran is an active continental domain accommodating the convergence between the Arabia and Eurasia plates. In northwestern Iran, deformation between the Central Iranian block and the Caucasus domain is mainly accommodated by right lateral strike-slip on the Tabriz fault. Cities and villages, including the city of Tabriz, have been destroyed by several strong historical earthquakes (M similar to 7). In this study, we compare the slip-rates estimated from geodetic measurements (radar interferometry and UPS) with those determined by dating a geomorphological offset of an alluvial fan along the Tabriz fault. The GPS measurements along two profiles normal to the Tabriz fault suggest a slip-rate of 7.3 +/- 1.3 mm yr(-1). The persistent scatterer radar interferometry analysis of Envisat satellite archives from 2003 to 2010 shows a velocity gradient (6 +/- 3 mm yr(-1)) across the Tabriz fault in agreement with GPS results. Moreover, it reveals that most of the area located south of the Tabriz fault is affected by subsidence, and that some sections of the fault probably act as barriers to fluid migration which may have an impact on its mechanical behaviour. West of Tabriz morphotectonic investigations on an alluvial fan surface show a right-lateral cumulative offset of 320 +/- 40 m Luminescence analyses of the coarse matrix alluvial fan deposits provide an age of 46 +/- 3 ka. This yields a slip-rate comprised between 6.5 and 7.3 mm yr(-1) along this segment. These results suggest that the Late Quaternary slip-rate is in agreement with the present-day slip-rate estimated by geodetic measurements, showing no slip-rate changes during the past 45 000 yr. Short-term variations within the 45 000 yr related to temporal earthquake clustering over few seismic cycles cannot be ruled out, but if they exist, they do not affect the geodetic and the geomorphological estimates. This study is in agreement with previous ones suggesting that long-term slip-rates (i.e. averaged over several tens of seismic cycles) are consistent with geodetic estimated slip-rates (i.e. extrapolated from few years of interseismic observations), and suggests that perturbations of fault slip-rates are related to variations over few seismic cycles.
ISSN: 0956-540X

hal-00844695
https://hal.archives-ouvertes.fr/hal-00844695
https://hal.archives-ouvertes.fr/hal-00844695v2/document
https://hal.archives-ouvertes.fr/hal-00844695/file/rizza2013.pdf
DOI : 10.1093/gji/ggt041

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault friction is a parameter that is difficult to assess along fault zones since its determination depends on the knowledge of any factor controlling the state of stress around faults. In brittle homogeneous rocks, a limited number of these factors, such as the shape of the fault surface, the vicinity of fault tips or the remote stress ratio, are crucial to constrain for this determination. In this paper, we propose to analyse a field example in which all these properties are met and where the nature of the slipped structure suggest differences in static friction. We compare the orientations of branching fractures at strike-slip relay zones between en echelon stylolites and en echelon joints both reactivated in shear. The field data are compared with both photoelastic and 3-D numerical models that consider the remote stress conditions and the role of the geometry of the strike-slip segments. Based on field observations, these analyses quantitatively demonstrate the significant role of fault friction on the local stress field orientation and subsequent fracture formation. This work points out that estimations of fault friction based on analyses of fracture patterns or in situ stresses must be accompanied with a thorough investigation of the 3-D fault shape, its segmentation and the remote stress state.
ISSN: 0191-8141

hal-00560999
https://hal.archives-ouvertes.fr/hal-00560999
DOI : 10.1016/j.jsg.2010.01.008