Éditeur(s) : Elsevier
Résumé : The blue shrimp Litopenaeus stylirostris was exposed to pond sediment for 48 h and its physiological response was studied in relation to molt stage. Shrimp were maintained in cages within a semi-intensive pond after 4 months of rearing. Hypoosmoregulatory capacity (hypo-OC), magnesium ions (Mg ions), glucose, total proteins and oxyhaemocyanin were assayed in haemolymph. An increase of 370% to 500% in Mg ions concentration and 200% to 266% in glucose concentration, and a decrease in hypo-OC in shrimp maintained close to the centre of the pond indicated a short-term stress response in all molt stages. Indicators of water and sediment pore water quality were within normal operating limits, however this area was characterized by high water content and relatively high total ammonia nitrogen in pore water of sediment. To a lesser extent, shrimp maintained in two other stations also presented a stress response. Physiological response of shrimp in molt stage D, compared to C/D-0 and D-2 seems to indicate that shrimp were more sensitive to environment at this stage. The use and choice of physiological parameters to detect shrimp stress in a pond are discussed.
Aquaculture (0044-8486) (Elsevier), 2006-03 , Vol. 253 , N. 1-4 , P. 703-711

Droits : 2005 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2006/publication-1675.pdf
DOI:10.1016/j.aquaculture.2005.09.008
http://archimer.ifremer.fr/doc/00000/1675/

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : We report rare earth element (REE) and neodymium (Nd) isotope data for the organic fraction of sediments collected from various depositional environments, i.e. rivers (n=25), estuaries (n=18), open-ocean settings (n=15), and cold seeps (n=12). Sedimentary Organic Matter (SOM) was extracted using a mixed hydrogen peroxide/nitric acid solution (20%-H2O2 – 0.02M-HNO3), after removal of carbonate and oxy-hydroxide phases with dilute hydrochloric acid (0.25M-HCl). A series of experimental tests indicate that extraction of sedimentary organic compounds using H202 may be complicated occasionally by partial dissolution of sulphide minerals and residual carbonates. However, this contamination is expected to be minor for REE because measured concentrations in H2O2 leachates are about two-orders of magnitude higher than in the above mentioned phases. The mean REE concentrations determined in the H2O2 leachates for samples from rivers, estuaries, coastal seas and open-ocean settings yield relatively similar levels, with ΣREE = 109 ± 86 ppm (mean ± s; n=58). The organic fractions leached from cold seep sediments display even higher concentration levels (285 ± 150 ppm; mean ± s; n=12). The H2O2 leachates for most sediments exhibit remarkably similar shale-normalized REE patterns, all characterized by a mid-REE enrichment compared to the other REE. This suggests that the distribution of REE in leached sedimentary organic phases is controlled primarily by biogeochemical processes, rather than by the composition of the source from which they derive (e.g. pore, river or sea- water). The Nd isotopic compositions for organic phases leached from river sediments are very similar to those for the corresponding detrital fractions. In contrast, the SOM extracted from marine sediments display εNd values that typically range between the εNd signatures for terrestrial organic matter (inferred from the analysis of the sedimentary detrital fractions) and marine organic matter (inferred from the analysis of local surface seawater). A notable exception is the case of organic matter (OM) fractions leached from cold seep sediment samples, which sometimes exhibit εNd values markedly different from both terrigenous and surface seawater signatures. This suggests that a significant fraction of organic compounds in these sediments may be derived from chemosynthetic processes, recycling pore water REE characterized by a distinct isotopic composition. Overall, our results confirm that organic matter probably plays an important role in the oceanic REE budget, through direct scavenging and remineralization within the water column. Both the high REE abundances and the shape of shale-normalized patterns for leached SOM also suggest that OM degradation in sub-surface marine sediments during early diagenesis could control, to a large extent, the distribution of REE in pore waters. Benthic fluxes of organic-bound REE could hence substantially contribute to the exchange processes between particulates and seawater that take place at ocean margins. Neodymium isotopes could provide useful information for tracing the origin (terrestrial versus marine) and geographical provenance of organic matter, with potential applications in paleoceanography. In particular, future studies should further investigate the potential of Nd isotopes in organic compounds preserved in sedimentary records for reconstructing past variations of surface ocean circulation.
Geochimica Et Cosmochimica Acta (0016-7037) (Pergamon-elsevier Science Ltd), 2014-09 , Vol. 140 , P. 177-198

Droits : 2014 Elsevier Ltd. All rights reserved.
http://archimer.ifremer.fr/doc/00191/30250/28682.pdf
DOI:10.1016/j.gca.2014.05.016
http://archimer.ifremer.fr/doc/00191/30250/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Coastal aquifers often display seawater intrusion resulting in the formation of a salty water wedge progressing inland. This study investigates the mass transfers in the mixing zone at the freshwater-seawater interface where the water is out of equilibrium with the rock-forming carbonates. Investigations were conducted in two boreholes, separated by 5 m, at the Ses Sitjoles test site (Mallorca Island, Spain) where repeated electrical conductivity logs of the formation and the saturating fluid, as well as regular pore-water sampling and permanent downhole multi-parameter monitoring of the water were performed over a period of 9 a. In the mixing zone, the significant acidification, the calcite saturation index profile and the Ca concentration profile cannot be explained by conservative mixing nor by dissolution-precipitation reactions only. Conversely, the analysis of organic C content and of the distinctly different time-resolved pH profiles measured in the two boreholes suggests the development of perennial biomass that triggers calcite dissolution. Moreover, the presence of biomass seems to be correlated with the permeability and vertical connectivity at the meter-scale. It is speculated that the mechanism could be self-activated because the microbiological activity induces calcite dissolution and tends to increase porosity and permeability that favors biomass development.
ISSN: 0883-2927

hal-00937665
https://hal.archives-ouvertes.fr/hal-00937665
DOI : 10.1016/j.apgeochem.2013.09.011

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
La Cabaña peridotite is part of a dismembered ophiolite complex located within the metamorphic basement of the Coastal Cordillera of south-central Chile, and is the only location in Chile were Cr-spinels have been described so far. The La Cabaña peridotite is part of the Western Series unit, which comprises meta-sedimentary rocks, metabasites, and serpentinized ultramafic rocks. This unit has been affected by greenschist-facies metamorphism with reported peak PT conditions of 7.0–9.3 kbar and 380°–420 °C. Within La Cabaña peridotite Cr-spinels are present in two localities: Lavanderos and Centinela Bajo. In Lavanderos, Cr-spinel occurs in small chromitite pods and as accessory/disseminated grains with a porous or spongy texture in serpentinite, whereas in Centinela Bajo Cr-spinel is present as accessory zoned grains in partly serpentinized dunites, and in chromitite blocks. All Cr-spinels display variable degrees of alteration to Fe2+-rich chromite with a variation trend of major elements from chromite to Fe2+-rich chromite similar to those observed in other locations, i.e., an increase in Fe2O3 and FeO, a decrease in Al2O3 and MgO. Cr2O3 content increases from chromite to Fe2+-rich chromite in chromitite pods from Lavanderos and chromitite blocks from Centinela Bajo, but decreases in ferrian chromite zones in accessory grains from Centinela Bajo. The minor element (Ti, V, Zn, Ni) content is mostly low and does not exceed 0.4 wt.%, with the exception of MnO (<0.9 wt.%), which shows a correspondence with increasing degree of alteration. Cr# (Cr/Cr + Al) versus Mg# (Mg/Mg + Fe2+) and Fe3+/Fe3++Fe2+ versus Mg# plots are used to illustrate the Cr-spinel alteration process. Overall, the Cr-spinels from Lavanderos (chromitite pods and disseminated grains) exhibit Cr# values ranging from 0.6 to 1.0, Mg# (Mg/Mg + Fe2+) below 0.5, and (Fe3+/Fe3++Fe2+) <0.4. Cr-spinels from chromitites in Centinela Bajo have Cr# and Mg# values that range from 0.65 to 1.0, and 0.7-0.3, respectively, and (Fe3+/Fe3++Fe2+) < 0.4. Accessory Cr-spinels from Centinela Bajo have Cr# and Mg# values that range from 0.55 to 1.0, and 0.6- < 0.1, respectively. The (Fe3+/Fe3++Fe2+) ratio is less than 0.4 in chromite cores and Fe2+-rich chromite, and >0.5 in ferrian chromite and Cr-magnetite. Interpretation of the data obtained and Cr-spinel textures indicate that the alteration of Cr-spinel is a progressive process that involves in its initial stages the reaction of chromite with olivine under water-saturated conditions to produce clinochlore and Fe2+-rich chromite. During this stage the chromite can also incorporate Ni, Mn, and/or Zn from the serpentinization fluids. As alteration progresses, Fe2+-rich chromite loses mass resulting in the development of a spongy texture. In a later stage and under more oxidizing conditions Fe3+ is incorporated in chromite/Fe2+-rich chromite shifting its composition to an Fe3+-rich chromite (i.e., ferrian chromite). Depending on the fluid/rock and Cr-spinel/silicate ratios, Cr-magnetite can also form over Fe2+-rich chromite and/or ferrian chromite as a secondary overgrowth. The compositional changes observed in Cr-spinels from La Cabaña reflect the initial stages of alteration under serpentinization conditions. Results from this study show that the alteration of Cr-spinels is dependent on temperature. The degree and extent of alteration (formation of Fe2+-rich and/or ferrian chromite) are controlled by the redox nature of the fluids, the Cr-spinel/silicate and the fluid/rock ratios.
ISSN: 0930-0708

hal-01172266
https://hal.archives-ouvertes.fr/hal-01172266
DOI : 10.1007/s00710-014-0335-5

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Tilt fluctuations can potentially reflect the response of hydrosystems to important rainfall. In this context, long baseline tiltmeters have been installed in an underground tunnel penetrating the Fontaine de Vaucluse karst to study the medium deformation related to solicitations exerted by water infiltrating the hydrosystem. The instruments monitor the tilt as well as its spatial variation. Northward tilts reaching a 1 μrad amplitude are observed consecutively to rainfalls. The tilt amplitude is highly correlated with the Fontaine de Vaucluse outlet flow fluctuations. The measured tilt signal is also relatively homogeneous over a 150 m length. Different types of structure likely to produce such observations are tested in order to identify their location with respect to the tiltmeters, their dimension as well as the amount of water level variation in the structure. Following rainfalls, the infiltration of water modifies the pore pressure, inducing a medium deformation. The hypothesis of an homogeneous surface loading on the Vaucluse plateau is first refuted since the related tilt is much lower than the one measured. The water supplied by rainfalls has to accumulate in discontinuities in order to generate a higher tilt. So, the deformation related to a pressure exerted on a fracture filled by water is assessed. A first study reveals the interest of the tilt homogeneity information that constrains strongly the fracture properties. Thus, the fracture must be located at a distance more than a few hundreds metres from the tiltmeters in order to produce a tilt homogeneous in space. If the fracture is initially dry, it must also be filled on a height higher than 150 m consecutive to a rainfall in order to generate a tilt amplitude in the same magnitude as the one measured. Then, we explore the influence of water level variations on the tilt produced by a fracture located at the interface between the saturated and unsaturated zones, which are thereby permanently flooded. Since several parameters of that model satisfactorily explain the field observations, we discuss how simultaneous geodetical observations could provide complementary information that would further constrain the geometry of the structure at the origin of the medium deformation.
ISSN: 0956-540X

insu-01408482
https://hal-insu.archives-ouvertes.fr/insu-01408482
https://hal-insu.archives-ouvertes.fr/insu-01408482/document
https://hal-insu.archives-ouvertes.fr/insu-01408482/file/Lesparre-2017.pdf
DOI : 10.1093/gji/ggw446

Éditeur(s) : HAL CCSD
Résumé : The Manche-à-Eau lagoon, brackish water ecosystem is subject to tide, trade winds and hurricanes. The 2004 map (IGN) is covered of a 90 m aside square, to place 37 spots in a GIS and to limit them on the field with a GPS. From aerial photos, the outlines drawing allows morphological follow up since 1950. Depth is measured at 1437 spots with bathymetric perch and prob. Stream direction is established during stream and ebb tide using ribbon fixed to the spot and a compass. Water volumes at low and high tide allow calculating the water renewal rate, at each tide. The mapping follow-up shows outlines and island stabilization because of the “shield effect” and soil (root peat), small islands aggregation/disaggregation depending of hurricanes passing. The present bathymetry shows the lagoon filling and the channels digging. General streams are subject to trade-winds (SSE-NNW) andthe tide movement to and fro. The up and down water generates a stream channel situated along the outlines and around dips and sandbanks. Water renewal volume (14.8 %) at each tide, combined with an active and various hydrodynamism tends to improve the water quality in this system.
Evolución Morfológica de la Laguna del Manglar Manche-à-EAU (Guadalupe, Antilles Francesas) de 1950 a 2004, y su batimetría eb 2007La laguna del Manche-à-Eau, ecosistema de agua salobre está sometido a la marea, a los alisios y a los huracanes. El mapa IGN de 2004 está dividido según una malla de 90 m para colocar 37 puntos en un SIG y limitarlos in situ con un GPS. Según las fotografías aéreas, el dibujo de los contornos hace posible el seguimiento morfológico desde 1950. La profundidad se mide en 1437 puntos con una pértiga y una sonda batimétrica. La orientación de las corrientes se establece en el mar y en el reflujo con catavientos fijados en los puntos, y una brújula. Las masas de agua entrantes y salientes permiten el cálculo del volumen de agua renovado durante cada marea. El seguimiento cartográfico muestra una estabilización de los contornos y de la isla debido al “efecto de escudo” y al suelo (turba de raíz), y una agregación/desagregación de los islotes según el paso de los huracanes. De acuerdo a la batimetría actual, se constatan el relleno de la laguna y la excavación de los canales. Las corrientes generales son controladas en superficie por los alisios, vientos de SSE-NNO y por el vaivén de la marea. Los movimientos ascendentes y descendentes de agua generan corrientes profundas a lo largo de los bordes y alrededor de depresiones y bajos. El volumen de agua renovado durante cada marea (14,8%) combinado al hidrodinamismo activo y variado tiende a vivificar este ecosistema.
La lagune de la Manche-à-Eau, écosystème d’eau saumâtre est soumis à la marée, aux alizés et aux ouragans. La carte IGN de 2004 est quadrillée selon une maille de 90 m pour placer 37 points dans un SIG et les borner sur le terrain avec un GPS. D’après les photographies aériennes, le dessin des contours rend possible le suivi morphologique depuis 1950. La profondeur est mesurée à 1437 points avec une perche et une sonde bathymétrique. L’orientation des courants est établie au flot et au jusant avec des penons fixés aux points, et une boussole. Les masses d’eau entrantes et sortantes permettent le calcul du volume d’eau renouvelé à chaque marée. Le suivi cartographique montre, une stabilisation des contours et de l’île due à « l’effet bouclier » et au sol (tourbe racinaire), et une agrégation/désagrégation des îlots selon le passage des ouragans. D’après la bathymétrie actuelle, le comblement de la lagune et le creusement des chenaux sont constatés. Les courants généraux sont gouvernés en surface par les alizés, vent de SSE-NNO et par le va-et-vient de la marée. Les descentes et remontées d’eau obligent ceux-ci à emprunter en profondeur les passages situés le long des berges et autour des dépressions et des hauts-fonds. Le volume d’eau renouvelé à chaque marée (14,8 %) combiné à l’hydrodynamisme actif et varié tend à vivifier cet écosystème.
Proceedings of the 61st Gulf and Caribbean fisheries institute
Le Gosier, Guadeloupe, France

hal-01600092
https://hal.archives-ouvertes.fr/hal-01600092
PRODINRA : 384819

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : We propose to assess the error done when temperature is considered as a conservative tracer in fluviokarst studies. As a matter of fact, heat exchanges occur between karstic Conduit System (CS) and Porous Fractured Matrix (PFM) that prevents from using this approximation without caution. The conservative tracer approximation boils down to consider the cooling of CS water by PFM flow in an open thermodynamic system where the CS is bounded by an Adiabatic Wall (AW). The resulting CS water temperature contrasts with the one obtained from more complete models (CW), which also take into account heat conduction within the CS, within the PFM, and from the CS to PFM through CS a Conductive Wall. In order to assess first orders of this error, the dimensionless equations, characteristic of CS cooling by PFM, have been solved thanks to Alternate Finite Difference Implicit methods both in AW and CW configurations. Four groups of dimensionless numbers appear in the various terms of energy and mass equations among which the Peclet and Reynolds numbers depict the large morphologic and hydrologic variability of natural karstic systems. A parametric exploration of the differences between AW and CW models has then been conducted vs. Peclet numbers (Pe numbers varying from 106 to 109, at constant CS Reynolds number) and vs. Reynolds numbers (Red varying from 103 to 107, at constant Peclet number). The error curves bound finite volumes in the Peclet–Reynolds space that converge uniformly to zero for the extreme values of these parameters. However, for Peclet and Reynolds numbers characteristic of realistic fluviokarst configurations, the errors reach finite values, that give first order information assessing the error done by considering temperatures as conservative tracers. Maximum relative errors around 10−2 (in fact 0.0092) have been found varying Pe; while it remained slightly lower than 0.7 × 10−2 varying Red. An illustrative example of the temperature conservative tracer AW approximation is presented with the data obtained from the main morphologic and hydrologic properties of the Cent–Font resurgence (Hérault, France). According to the results, the error reached at the output of the fluviokarst is 0.00613 (for Pe = 1.4993 × 108 and Red = 4.2969 × 104). When rescaled to the physical domain, this error leads to a temperature difference of 1.77 K between the CW and AW configurations.
ISSN: 1812-2108

hal-01358348
https://hal.archives-ouvertes.fr/hal-01358348
https://hal.archives-ouvertes.fr/hal-01358348/document
https://hal.archives-ouvertes.fr/hal-01358348/file/hessd-11-169-2014.pdf
DOI : 10.5194/hessd-11-169-2014

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : Society's needs for a network of in situ ocean observing systems cross many areas of earth and marine science. Here we review the science themes that benefit from data supplied from ocean observatories. Understanding from existing studies is fragmented to the extent that it lacks the coherent long-term monitoring needed to address questions at the scales essential to understand climate change and improve geo-hazard early warning. Data sets from the deep sea are particularly rare with long-term data available from only a few locations worldwide. These science areas have impacts on societal health and well-being and our awareness of ocean function in a shifting climate. Substantial efforts are underway to realise a network of open-ocean observatories around European Seas that will operate over multiple decades. Some systems are already collecting high-resolution data from surface, water column, seafloor, and sub-seafloor sensors linked to shore by satellite or cable connection in real or near-real time, along with samples and other data collected in a delayed mode. We expect that such observatories will contribute to answering major ocean science questions including: How can monitoring of factors such as seismic activity, pore fluid chemistry and pressure, and gas hydrate stability improve seismic, slope failure, and tsunami warning? What aspects of physical oceanography, biogeochemical cycling, and ecosystems will be most sensitive to climatic and anthropogenic change? What are natural versus anthropogenic changes? Most fundamentally, how are marine processes that occur at differing scales related? The development of ocean observatories provides a substantial opportunity for ocean science to evolve in Europe. Here we also describe some basic attributes of network design. Observatory networks provide the means to coordinate and integrate the collection of standardised data capable of bridging measurement scales across a dispersed area in European Seas adding needed certainty to estimates of future oceanic conditions. Observatory data can be analysed along with other data such as those from satellites, drifting floats, autonomous underwater vehicles, model analysis, and the known distribution and abundances of marine fauna in order to address some of the questions posed above. Standardised methods for information management are also becoming established to ensure better accessibility and traceability of these data sets and ultimately to increase their use for societal benefit. The connection of ocean observatory effort into larger frameworks including the Global Earth Observation System of Systems (GEOSS) and the Global Monitoring of Environment and Security (GMES) is integral to its success. It is in a greater integrated framework that the full potential of the component systems will be realised. Crown Copyright (C) 2011 Published by Elsevier Ltd. All rights reserved.
Progress In Oceanography (0079-6611) (Pergamon-elsevier Science Ltd), 2011-10 , Vol. 91 , N. 1 , P. 1-33

Droits : 2011 Published by Elsevier Ltd. All rights reserved.
http://archimer.ifremer.fr/doc/00044/15557/15923.pdf
DOI:10.1016/j.pocean.2011.05.001
http://archimer.ifremer.fr/doc/00044/15557/

Éditeur(s) : HAL CCSD Geological Society of America
Résumé : International audience
Fluid-rock interactions can control earthquake nucleation and the evolution of earthquake sequences. Experimental studies of fault frictional properties in the presence of fluid can provide unique insights into these interactions. We report the first results from experiments performed on cohesive silicate-bearing rocks (microgabbro) in the presence of pressurized pore fluids (H2O, drained conditions) at realistic seismic deformation conditions. The experimental data are compared with those recently obtained from carbonate-bearing rocks (Carrara marble). Contrary to theoretical arguments, and consistent with the interpretation of some field observations, we show that frictional melting of a microgabbro develops in the presence of water. In microgabbro, the initial weakening mechanism (flash melting of the asperities) is delayed in the presence of water; conversely, in calcite marble the weakening mechanism (brittle failure of the asperities) is favored. This opposite behavior highlights the importance of host-rock composition in controlling dynamic (frictional) weakening in the presence of water: cohesive carbonate-bearing rocks are more prone to slip in the presence of water, whereas the presence of water might delay or inhibit the rupture nucleation and propagation in cohesive silicate-bearing rocks.
ISSN: 0091-7613

hal-01054327
https://hal.archives-ouvertes.fr/hal-01054327
DOI : 10.1130/G34916.1

Éditeur(s) : HAL CCSD
Résumé : The heterogeneous nature and sometimes karstified carbonate environments has a direct impact on many environmental issues, such as coastal aquifers affected by saltwater intrusion. At the south of the island of Mallorca (Spain), the Llucmajor carbonate platform offers a privileged site for the study of such intrusions including the experimental site of Campos who meets the intrusion at shallow depth. The characterization of heterogeneous properties passes through a preliminary description of the properties of carbonate reservoirs, including those of the porosity. According to the wide range of sizes of heterogeneities from micrometer to hundreds of meters, the use of multiscale methods is required. This thesis focused on the determination of multiscale porosities from the microporosity to karstic porosity, and of relationships between observation scale changes of these properties. At the micron scale, high-resolution X-ray microtomography allows to extract the microporosity and the microporous network connectivity. At lower resolution (mm), X-ray tomography is also used to study the micro- and macro-porous network at the core scale which is already allocated to number of observations and measurements, including petrophysical. At the borehole scale, the wall images are used to identify the dissolved zones from centimeter macropores to plurimetric karstic cavities. At the larger scale, surface geophysics study the lateral extension of the karsts and heterogeneities. Finally, the porous structure of the studied site is integrated with its wide range of scales into the regional geology of the Llucmajor platform. Thus, the hydrogeophysical observatory set up on the site of Campos to monitor the spreading of salt water in the aquifer is integrated in its geological and petrophysical context, in order to refine the interpretation of its variations of salinity measurements during the time.
La nature hétérogène et parfois karstifiée des milieux carbonatés a un impact direct sur nombre de problématiques environnementales, comme celle des aquifères côtiers affectés par une intrusion d'eau salée. Au sud de l'ile de Majorque (Baléares, Espagne), la plate-forme carbonatée de Llucmajor offre un site privilégié pour l'étude de telles intrusions notamment avec le site expérimental de Campos, qui rencontre l'intrusion à faible profondeur. La caractérisation des propriétés hétérogènes du réservoir passe par une description préalable des propriétés des réservoirs carbonatés et notamment celle de la porosité. Au regard de la large gamme d'échelles d'hétérogénéités allant du micromètre à la centaine de mètre, l'utilisation de méthodes multi-échelles est nécessaire. Ce travail de thèse a porté sur la caractérisation multi-échelle de la porosité, allant de la microporosité à la porosité karstique, et l'établissement de relations entre les changements d'échelles d'observation de ces propriétés. A très petite échelle, la microtomographie haute-résolution à rayons X extrait à l'échelle du micron la microporosité et la connectivité des réseaux microporeux. A plus basse fréquence (celle du mm), la tomographie est également utilisée afin d'étudier le réseau micro- et macroporeux à l'échelle des carottes, à laquelle sont réalisées nombre d'observations et de mesures, notamment pétrophysiques. A l'échelle du puits, les images de paroi permettent d'identifier les zones de dissolution allant des macropores centimétriques aux cavités karstiques plurimétriques. A plus grande échelle, la géophysique de surface permet d'étudier l'extension latérale de ces karsts et hétérogénéités. Enfin, la structure poreuse du site étudié sur cette vaste gamme d'échelles est intégrée à la géologie régionale de la plate-forme de Llucmajor. Ainsi, l'observatoire installé sur le site pour surveiller la propagation de l'eau salée dans l'aquifère a pu être replacé dans son contexte géologique et pétrophysique, afin d'affiner l'interprétation de ses mesures de variations de salinité au cours du temps.
https://tel.archives-ouvertes.fr/tel-00633488

tel-00633488
https://tel.archives-ouvertes.fr/tel-00633488
https://tel.archives-ouvertes.fr/tel-00633488/document
https://tel.archives-ouvertes.fr/tel-00633488/file/TheseHebert.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Electrical resistivity soundings are used by geophysicists to determine the structure and composition of the Earth's crust and mantle and to explore natural resources (ore, oil, gas, water). Their interpretations in terms of composition and in-situ physical conditions depend mainly on laboratory measurements of electrical conductivity of rocks at simulated crustal conditions of temperature, pressure, saturation and pore pressures. These measurements present a numbers of limitations, in particular, in the case where conductive pore fluids are present, as in the case of deep reservoir conditions, where temperature exceeds 250 A degrees C. Here, we present a new cell capable of measuring electrical conductivity of large saturated samples at confining pressure up to 200 MPa, pore pressure up to 50 MPa, and temperature up to 500 A degrees C. The measurement cell has been developed in a commercial, internally heated, gas pressure apparatus (Paterson press). It is based on the concept of "guard ring" electrode, which is adapted to samples that are jacketed by a very conductive, metallic material. Numerical modeling of the current flow in the electrical cell allowed defining the optimal cell geometry. Calibration tests have been performed on Fontainebleau sandstones saturated with electrolytes of different conductivities, up to 350 A degrees C. The resulting electrical formation factor and temperature dependence of electrical conductivity are in very good agreement with previous studies. This new cell will improve the exploration and exploitation of deep fluid reservoirs, as in unconventional, high enthalpy geothermal fields. In particular, the investigations address possible effects of fluid-rock interactions on electrical resistivity of a reservoir host rock.
ISSN: 0169-3913

hal-00681997
https://hal.archives-ouvertes.fr/hal-00681997
DOI : 10.1007/s11242-011-9846-2

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : Total mercury (HgT) and monomethylmercury (MMHg) were investigated in a tropical head watershed (1 km(2)) of French Guiana. The watershed includes a pristine area on the hill slopes and a former gold mined flat in the bottomland. Concentrations of dissolved and particulate HgT and MMHg were measured in rain, throughfall, soil water and at three points along the stream. Samples were taken in-between and during 14 storm events at the beginning and middle of the 2005 and 2006 rainy seasons. Dissolved and particulate HgT concentrations in the stream slightly increased downstream, while dissolved and particulate MMHg concentrations were low at the pristine sub-watershed outlet (median = 0.006 ng L-1 and 1.84 ng g(-1), respectively) and sharply increased at the gold mined flat outlet (median = 0.056 ng L-1 and 6.80 ng g(-1), respectively). Oxisols, which are dominant in the pristine area act as a sink of HgT and MMHg from rain and throughfall inputs. Hydromorphic soils in the flat are strongly contaminated with Hg (including Hg droplets) and their structure has been disturbed by former gold-mining processes, leading to multiple stagnant water areas where biogeochemical conditions are favorable for methylation. In the former gold mined flat high dissolved MMHg concentrations (up to 0.8 ng L-1) were measured in puddles or suboxic soil pore waters, whereas high dissolved HgT concentrations were found in lower Eh conditions. Iron-reducing bacteria were suggested as the main methylators since highest concentrations for dissolved MMHg were associated with high dissolved ferrous iron concentrations. The connection between saturated areas and stagnant waters with the hydrographic network during rain events leads to the export of dissolved MMHg and HgT in stream waters, especially at the beginning of the rainy season. As both legal and illegal gold-mining continues to expand in French Guiana, an increase in dissolved and particulate MMHg emissions in the hydrographic network is expected. This will enhance MMHg bio-amplification and present a threat to local populations, whose diet relies mainly on fish.
Water Research (0043-1354) (Pergamon-elsevier Science Ltd), 2011-04 , Vol. 45 , N. 8 , P. 2659-2669

Droits : 2011 Elsevier Ltd All rights reserved.
http://archimer.ifremer.fr/doc/00035/14628/12134.pdf
DOI:10.1016/j.watres.2011.02.022
http://archimer.ifremer.fr/doc/00035/14628/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study explores the dynamics of porosity and reactive surface area changes during porous limestone dissolution by CO2-rich water. The Sr and Ca concentrations in both the rock and the outlet solution are used to evaluate the reactive surface area changes of the two rock-forming calcites, i.e. micrite grains and sparite crystals, which have different trace element signatures. The geometric surface area measured with X-ray microtomography decreases slightly whereas the reactive surface area increases continuously with increasing porosity from 20.3 to 30.2%. Surprisingly, changes in reactive surface areas are very different between the two calcites. The reactive surface area changes in the micrite are parabolic while the reactive surface area of sparite increases greatly. The numerical model HYTEC is used to model the change in reactive surface areas during the experiment. Different geometrical models are tested. The model based on spherical-grain dissolution and spherical-pore growth fails to reproduce the experimental results, while the sugar-lump model provides reasonable agreement with the experiment.
ISSN: 0009-2541

hal-00445274
https://hal.archives-ouvertes.fr/hal-00445274
DOI : 10.1016/j.chemgeo.2009.01.032

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
Determination of the membrane seal capacity of deformation bands is critical for managing geologic reservoirs in porous sandstones. In this study, we have analyzed a cataclastic shear-band network developed in uncemented porous sandstone in Provence, France. Geometrical analyses of the bands show significant differences between three types of bands (single strand, multistrand, and band cluster), sorted by their number of strands, their amount of shear displacement, and their thicknesses. At the microscopic scale, the image-analysis porosities and the grain-size distributions allow definition of three different types of microstructural deformation: damage zone, protocataclastic, and cataclastic. Whereas damage zone and protocataclastic deformations are observed in each type of band, cataclastic strands are observed in clusters and, sometimes, in multistrands. Cataclastic strands are characterized by a porosity reduction of 10 to 25% and a permeability reduction of three to five orders of magnitude compared to the host rock. Field observations of iron hydroxide precipitations around the bands suggest that cataclastic strands were membrane seals to water flow under vadose condition. This study therefore highlights the importance of the degree of cataclasis in shear bands as membrane seals to subsurface fluid flows in sandstone reservoirs.
ISSN: 0149-1423

hal-00766557
https://hal.archives-ouvertes.fr/hal-00766557
DOI : 10.1306/04051211097

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A shallow field experimental site for CO2 injection was established at Maguelone (Languedoc, France), in order to test in an integrated manner a suite of surface and downhole hydrogeophysical monitoring methods. The objective is to improve monitoring of gas transport in the shallow subsurface and to determine the sensitivity of CO2 monitoring systems for leakage detection. The site offers a natural laboratory to study the processes associated with CO2 injection in a clastic and clay-rich context saturated with saline fluids. Prior to CO2 injection, three nitrogen (N2) injections were undertaken in 2012 to measure the site response to neutral gas injection. In 2013, a volume of 111 m3 (mass of 220 kg) of CO2 was injected during 3.5 h at 15 m depth. During each experiment, the gas plumes were successfully detected from pressure monitoring, time-lapse induction logging and downhole resistivity monitoring with dipole–dipole array. Increases in resistivity are attributed to free gas propagation (either N2 or CO2) whereas decreases in resistivity correlate with CO2 dissolution in the pore fluid. Chemical analyses confirm this hypothesis with a decrease in pH and an increase in the concentration of dissolved species in the latter case.
ISSN: 1750-5836

hal-01355943
https://hal.archives-ouvertes.fr/hal-01355943
DOI : 10.1016/j.ijggc.2015.12.005

Éditeur(s) : HAL CCSD
Résumé : International audience
Abstract View references (38)This work presents a facile, scalable method for the fabrication of graphene oxide-iron oxide (GO-Fe3O4) nanocomposites produced by co-precipitation of iron ions onto the GO surfaces in basic aqueous media. FTIR and XRD characterisation suggests that Fe3O4 was chemically anchored to the GO sheets, possibly via the carboxyl and hydroxyl groups. Small GO loadings of 0.5 and 1 wt% were not sufficient to alter the Fe3O4 structures. However, increasing the GO loading to 5 and 10 wt% resulted in significant loss in pore volume, thus suggesting the lamellar GO sheets decorated with Fe3O4 were assembling into GO-Fe3O4 nanocomposite stacks. It was found that the GO-Fe3O4 nanocomposites had an enhanced catalytic activity in the heterogeneous Fenton-like oxidation of Acid Orange 7 (AO7) compared to pure GO flat sheets and Fe3O4 nanoparticles. Interestingly, the GO-Fe3O4 nanocomposite with 5 wt% loading ratio exhibited the best catalytic activity with 76% degradation of AO7 dye observed within 90 min of reaction. This was attributed to the synergistic effect of GO by enriching the adsorbed AO7 molecules onto the nanocomposite to be further oxidised in the vicinities of active sites. This finding suggests the promising employment of GO-Fe3O4 nanocomposites in removing organic dyes from polluted water by heterogeneous Fenton-like reaction. © 2014 by American Scientific Publishers.
SCIENCE OF ADVANCED MATERIALS

hal-01683207
https://hal.univ-antilles.fr/hal-01683207
DOI : 10.1166/sam.2014.1812

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Urucum region (Mato Grosso do Sul, Brazil) contains Neoproterozoic–Cambrian manganese ore in the layers Mn-1, Mn-2, and Mn-3, which are interbedded with iron formations (IFs) from the Santa Cruz Formation (Jacadigo Group) and surrounded by carbonate rocks from the Bocaina and Tamengo Formations (Corumbá Group). These rocks fill an ancient graben, with sediments from the Santa Cruz Formation overlying fluvial deposits from the Urucum Formation and limestones from the Bocaina and Tamengo Formations deposited in the shallow marginal regions. As the graben deepened, it was flooded with microbe-rich seawater and hydrothermalism began. Iron and manganese precipitated within the pores in arkosic sandstones, thereby forming the clastic Lower Mn-1 ore layer. The remaining manganese was simultaneously deposited on the basin floor with clastic clay and silt from turbidity currents, thereby forming the Upper Mn-1 clastic–chemical ore layer. The sedimentation of Mn-1 and its host IFs was controlled by seawater saturation and homogeneous oxidation, which caused manganese and iron sedimentation and the death of microorganisms, generating mangano-ferriferous sediments with high P, Co and Ni contents. Mn-2 formed during periods of tectonic quiescence through water influxes that carried abundant microbes, Fe(II), Mn(II), and SiO2. Under UV radiation, these microbes oxidized Mn(II) and Fe(II) to form hydroxides and died, thereby forming biomass that was enriched in P, Co and Ni and minor carbonate adjacent to and below the oxycline. These microbes also formed kremydilites, oblate structures that resemble manganese stromatolites, within the biomass and produced CH4 and/or H2 gas bubbles. During early diagenesis, wormlike organisms inhabited the biomass and probably separated iron from manganese to produce cryptomelane microbialites, which agglutinated to form manganese micronodules that coalesced to form the massive layer Mn-2. This process ended with the disappearance of microorganisms and the sedimentation of the IFs, and a new water influx generated layer Mn-3 via the same process. The final seawater upwelling precipitated IFs in the basin depocenter, whereas limestone from the Tamengo Formation was deposited along the basin’s edges. The diagenesis initially transformed the manganese oxides into cryptomelane and then into hollandite.
ISSN: 0169-1368

hal-01684668
https://hal.archives-ouvertes.fr/hal-01684668
DOI : 10.1016/j.oregeorev.2017.09.018

Éditeur(s) : HAL CCSD
Résumé : International audience
The purpose of our study is to model a geothermal reservoir. When geothermal reservoir are assumed to be composed of pure water, the transfer of mass and energy is classically described by two balance equations: mass balance equation and the energy balance equation. In addition to those equations, fluid velocity ist classically given by the Darcy law while thermodynamic properties, inferred from theoretical or empirical equations of state, are used to close the mathematical system. Once this system is closed, there exist different solutions. The first one is to solve for pressure and temperature with a variable switch to saturation in the two-phase region (e.g. TOUGH2). The second one is to solve for pressure and enthalpy to increase stability of phase transition between single and two-phase states (e.g. Hydrotherm). We adopted the second option and chose te use a splitting method to get rid of the complexity of coupling equations and a finite volume method for the spatial discretization. Selecting object-oriented languages, we developed a multi-language framework, combining Python, Fortran and a C++ implementation of IAPWS (from the freesteam project) including the supercritical equations, in porous media velocity is given by Darcy law and to close the system physical properties are determined by the IAPWS-IF97 thermodynamic formulation. We resolve the equations in pressure and enthalpy instead of pressure and temperature in order to increase stability and to handle easier the passage from a single-phase to a two-phase system. We solve the system by using a splitting method - to get rid of the complexity of coupling equations - and a finite volume method. We offer some freedom to users thanks to the implementation of several methods like explicit or implicit Euler, Runge-Kutta or BDF2 for time solvers or GMRES and BICGSTAB for the linear solver. We can handle several boundary conditions like no-flow - describing a boundary which can not exchange matter with the exterior - or like a mixed-therm condition - a Dirichlet condition to the pressure and a Dirichlet or an outflow condition to the temperature in order to describe a recharge or a discharge zone - ... We're developing a multi-language framework, combining Python, Fortran and the C++ implementation of IAPWS (from the freesteam project). All these languages are object-oriented. We've applied this simulation model to the dogger in Paris, France, to several one-dimensional systems and a two-dimensional one made by Coumou with the CSMP++ platform. The dogger is a reservoir exploited to produce heat by pumping water at 70 and reinjecting it in the reservoir at 40. In the one-dimensional systems we wanted to observe the process of heat transfer from a higher temperature boundary to a smaller one in a high-energy domain. The last simulation shows the natural convection of water in a fault. For every simulation we compared the solutions we found with an other code (TOUGH2 or CSMP++) and they agreed. The next step will be to model the geothermal plant in Guadeloupe, West Indies. It's the only place in France - and in the West Indies so far - producing electricity with the earth power. The temperature can reach up to 1000 and the pressure range is around a few hundreds MPa. In some surface zones we can see two-phase water at atmospheric pressure. In the 1980s Bouillante was a laboratory for France. Since 1995 Bouillante has given 30GWh electricity a year to the Guadeloupeans.
PROCEEDINGS, Thirty-Ninth Workshop on Geothermal Reservoir Engineering
Stanford, United States

Droits : info:eu-repo/semantics/OpenAccess
hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133/document
https://hal-brgm.archives-ouvertes.fr/hal-00944133/file/Copol.pdf

Éditeur(s) : HAL CCSD
Résumé : In coastal carbonate aquifers submitted to a saline intrusion, water - rock interactions processes at the interface between freshwater and saltwater are a cause for heterogeneities development within the porous media. The dissolutions and precipitations induced by the mixing zone play a major role in the transport properties of the reservoir and so in the long term evolution of the saltwater intrusion. The characterization and the in situ observation of a current saline intrusion in the Llucmajor carbonate platform at the experimental site of Ses Sitjoles (South-Easth of Mallorca Island, Spain), allowed to study the temporal evolution of the saltwater intrusion and the biogeochemical processes active in the mixing zone. The influence of microstructure, characterized using X-Ray microtomography, on the petrophysical and flow properties was investigated in laboratory and flow-through experiments were also conducted to study the modifications of the microstructures when submitted to water - rock interactions processes. The mixing zone at the Ses Sitjoles site appears as quite thick and not very sensitive to climate and anthropic stress and is proved to be the locus of active microbiological activity. Laboratory studies highlight a strong control of the microporosity on transport processes and of pCO2 on water - rock interactions. The percolation experiments of slightly reactive waters reveal calcite dissolution together with a decrease in permeability due to a rearrangement of micro-grains within the microporous network.
Les processus d'interactions fluide-roche à l'interface eau douce-eau salée, dans les aquifères carbonatés côtiers soumis à une intrusion saline, sont une des causes du développement d'hétérogénéités dans la structure du milieu poreux. Les dissolutions et/ou précipitations engendrées par la présence de cette zone de mélange jouent un rôle déterminant pour les propriétés de transport du réservoir et donc l'évolution à long terme de l'intrusion d'eau salée. En prenant l'exemple de la plateforme carbonatée de Llucmajor au niveau du site expérimental de Ses Sitjoles (Sud-Est de Majorque, Espagne), un travail de caractérisation et d'observation in situ à moyen terme de l'intrusion saline actuelle de ce réservoir permet de décrire son évolution temporelle et les processus biogéochimiques actifs dans la zone de mélange. L'influence de la microstructure du milieu poreux, caractérisée par microtomographie RX, sur les propriétés pétrophysiques et hydrodynamiques est étudiée en laboratoire et des expériences de percolations d'eaux réactives (mélanges eau douce - eau salée et eau pure chargée en CO2) sont réalisées afin d'étudier les modifications de ces microstructures lorsqu'elles sont soumises à des interactions eau - roche. La zone de mélange eau douce - eau salée rencontrée au niveau du site de Ses Sitjoles est large et peu sensible aux contraintes extérieures (climatologiques et anthropiques) et constitue un lieu d'activité microbiologique particulièrement actif. En laboratoire, on observe un fort contrôle des phénomènes de transport par la microporosité et des processus d'interactions eau - roche par la pCO2. Dans le cas d'une percolation de fluides moyennement réactifs, les expériences mettent en évidence une dissolution de calcite accompagnée par une diminution de la perméabilité, liée à un réarrangement des micro-grains à l'intérieur du réseau microporeux.
https://tel.archives-ouvertes.fr/tel-00767152

tel-00767152
https://tel.archives-ouvertes.fr/tel-00767152
https://tel.archives-ouvertes.fr/tel-00767152/document
https://tel.archives-ouvertes.fr/tel-00767152/file/thesegaring.pdf