Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Previous work has demonstrated that geoelectrical measurements, acquired either along the Earth’s surface or in boreholes, can be sensitive to the presence of fractures. However, a lack of numerical approaches that are well suited to modelling electric current flow in fractured media prevents us from systematically exploring the links between geoelectrical measurements and fractured rock properties. To address this issue, we present a highly computationally efficient methodology for the numerical simulation of geoelectrical data in 2.5-D in complex fractured domains. Our approach is based upon a discrete-dual-porosity formulation, whereby the fractures and rock matrix are treated separately and coupled through the exchange of electric current between them. We first validate our methodology against standard analytical and finite-element solutions. Subsequent use of the approach to simulate geoelectrical data for a variety of different fracture configurations demonstrates the sensitivity of these data to important parameters such as the fracture density, depth, and orientation.
ISSN: 0956-540X

hal-01622151
https://hal.archives-ouvertes.fr/hal-01622151
https://hal.archives-ouvertes.fr/hal-01622151/document
https://hal.archives-ouvertes.fr/hal-01622151/file/sanzGJI2017.pdf
DOI : 10.1093/gji/ggx080

Éditeur(s) : HAL CCSD Elsevier
Résumé : To contribute to the understanding of how opening-mode fractures (joints) form and open or close at depth in layered rocks, we present a 2D numerical study aiming to determine whether tensile stress can develop in pre-fractured elastic multilayers submitted to biaxial compressive strain conditions. First, we investigate the role of the elastic and geometrical properties of the layers on the development of tensile stress in models with five bonded layers and containing one open fracture in the central layer. Our results indicate that, in absence of elastic contrast (in Young's modulus) between the layers, no tensile stress develops in the models. However, when the fractured layer is stiffer than the two adjacent layers directly above and below, a lobe of horizontal tensile stress develops centered on the pre-existing fracture. The creation of this tensile stress is contingent upon the partial closing of the fracture. The levels of tensile stress and the thickness of the lobe of tensile stress increase logarithmically with an increase in the elastic contrast and are systematically larger for a larger Soft/Stiff ratio (ratio of the total thickness of the soft layers with the total thickness of the stiff layers). Second, we investigate the role of fracture interaction in the development of tensile stress in models containing a pair of open fractures. We observe that the levels of tensile stress in the region between the fractures are systematically higher than those observed in identical models containing a single fracture. This increase in tensile stress is very large for small elastic contrasts between the layers but diminishes when the elastic contrast increases. Furthermore, the spacing between the pre-existing fractures plays an important role in the stress distribution in the region between them. When the fracture spacing is equal to or lower than 1.15 times the height of the fractured layer for the experimental conditions chosen, the lobes of tensile stress centered on the fractures coalesce. This results in the formation of vast areas of tensile stress in models under remote compressive loading conditions. Such tensile areas are likely to allow the initiation and propagation of subsequent opening-mode fractures. The results obtained provide new insights into the formation of joints in layered rocks in compressive environments, with important consequences on fluid flow.
ISSN: 0040-1951

hal-00407576
https://hal.archives-ouvertes.fr/hal-00407576
DOI : 10.1016/j.tecto.2006.12.003

Éditeur(s) : HAL CCSD
Résumé : Today, one of the main challenges in the oil industry is the exploitation of new resources in naturally fractured reservoirs often located in structurally complex areas such as plate boundaries, mountain ranges or near salt structures. While numerical models of rock deformation based on continuum mechanics are becoming industry standard in providing efficient means for modelling natural fractures in reservoirs, the knowledge of past perturbed stress fields, which is referred as the type (normal, wrench or reverse), orientation and magnitude of the regional or local tectonic stresses that needs to be applied as boundary condition in numerical simulations, is often unknown or approximated.The essence of this thesis is to improve the recovery of the paleostress field needed to constrain numerical simulations. I first described and discuss through a comprehensive mechanically-based multi-parametric study how far we can rely on the commonly used paleostress inversion methods based on fault slip data and the Wallace and Bott assumptions. I then compared this method with a new generation technique based on geomechanics using field observations. Since slip markers on faults are hardly observed in core or image log, I used observed natural fracture data as main drivers for the inversion of the paleostress using geomechanically-based method. I demonstrated, through various outcrop and subsurface examples, how this can efficiently be done. Finally, I aimed at addressing the problem of polyphase fracture data sets with unknown mechanical type (joints, faults, stylolites ...) and expanded the mechanical stress inversion to the separation of tectonic phases.
Aujourd'hui, l'un des principaux défis dans l'industrie pétrolière est l'exploitation de nouvelles ressources dans les réservoirs naturellement fracturés souvent situés dans des zones structurellement complexes tels que les frontières de plaques, les chaînes de montagnes ou les structures de proches des dômes de sel. Alors que les modèles numériques de déformation des roches basée sur la mécanique des milieux continus fournissant des moyens efficaces pour la modélisation de fractures naturelles dans les réservoirs, sont devenus la norme dans l'industrie, les paléo-contraintes régionales ou locales appliquées comme condition aux limites dans les simulations numériques, définies par le régime (normal, décrochant ou inverse), l'orientation, et la magnitude des contraintes tectoniques, sont souvent inconnues ou approximées.L'essence de cette thèse est d'améliorer la prédiction du champ de paléo-contrainte nécessaire pour contraindre les simulations numériques. J’ai décrit dans un premier temps à travers une étude comparative multi-paramétrique complète basée sur la mécanique, dans quelle mesure nous pouvions compter sur les méthodes d'inversion des paléo-contraintes basées sur les hypothèses de Wallace et Bott et les données de glissement sur les failles. J’ai ensuite comparé ces méthodes avec une technique d’inversion de nouvelle génération basée sur la géomécanique en utilisant les observations de terrain. Puisque les marqueurs de glissement sur les failles sont rarement observés le long du forage, j’ai utilisé l’inversion géomécanique des contraintes pour les données de fractures naturelles observées. J’ai alors démontré, l’efficacité de cette technique à travers divers exemples d'affleurements et de subsurface. Enfin, j’ai proposé une solution afin de résoudre le problème des données de fractures polyphasées à type cinématique inconnu (joints, failles, stylolites ...) et étendu l’inversion de contrainte basée sur la géomécanique à la séparation des phases tectoniques.
https://hal.archives-ouvertes.fr/tel-01324110

tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110/document
https://hal.archives-ouvertes.fr/tel-01324110/file/theselejri.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : Results are reported for an acidic water flow-through experiment conducted in a fractured argillaceous limestone sample (73% carbonates). The change in fracture geometry and related parameters is reported for six data sets obtained from synchrotron X-ray microtomography experiments. High-resolution three-dimensional images of the sample allowed quantification of the changes in fracture morphology at a spatial resolution of 6 ;μm. Mineral mass loss and permeability changes in the sample were also determined. Several physico-chemical phenomena were identified during the experiment. Initial smooth fracture surfaces evolved rapidly toward rough surfaces with uneven clay coverage due to the preferential dissolution of carbonate minerals compared to clay minerals whose dissolution rate is about 106 slower. A microporous clay coating progressively developed at the fluid-rock interface during heterogeneous dissolution of the fracture, while the global dissolution rate of the fracture walls exponentially decreased. The increase in surface roughness and the presumed reorganization of clays caused a progressive reduction in permeability. During the last flow-through stage, a large decrease in sample permeability was attributed to the large removal of clay particles; this process was responsible for a dramatic collapse of the fracture walls near the sample inlet and led to the development of preferential flow pathways. The development of the clay coating also acted as a barrier to flow and mass transfer between calcite grains and bulk solution and affected transport processes within the fracture
ISSN: 0043-1397

hal-00405333
https://hal.archives-ouvertes.fr/hal-00405333
DOI : 10.1029/2006WR005379

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
Recent mathematical calculations allow us to define set fracture intensity (I), i.e., the amount of rock mass affected by fracture sets, independently of the investigation mode. This parameter, characteristic of each rock mass, is of much interest to describe the mechanical response of the rock mass to external influences. The aim of this work is to apply these mathematical equations on one site using measurements of three distinct fracture sets: (1) on a plane surface, (2) along a scanline, and (3) using borehole imaging, in order to evaluate and explain variability in collected data. Even if the three types of measurements give differences on absolute intensity values, they still define similar trends, i.e., the order of the fracturing impact of joint sets is the same from the three measurement methods, irrespective of the fact that obtained values are quite different from one survey method to another. We discuss the possible origins of these biases.
ISSN: 1435-9529

hal-01121556
https://hal.archives-ouvertes.fr/hal-01121556
DOI : 10.1007/s10064-014-0572-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : Different types of fractures and fault rocks occur within the major normal fault zones bordering the NW of the Neogene Penedes basin (NE Spain). In the southwest part of the basin, the main fault is the Baix Penedes fault that places the Upper Jurassic-Lower Cretaceous dolomicrites of the footwall in contact with the Miocene siliciclastic sediments of the hangingwall. Within the footwall damage zone, different fracture systems and their respective associated breccias and cements have been recognized. Using a combination of structural, petrologic and geochemical analyses, we show that these fracture systems evolved from mainly tectonic to mainly karstic features during the progressive development and upward propagation of the fault. The earlier fractures and associated breccias represent the initial stages of the fault propagation, when the process zone formed around the fault tip was dominated by dilatant fracturing (fractures 1 and dilatant breccias B1). The fluid involved in this early deformation precipitated the dolomite cement Cl, in equilibrium with the host-rock in a closed hydrogeological system. Localization of frictional processes generated cataclasites and ultracataclasites along distinct second-order faults (fractures 2). In these fractures, the dolomite cement C2 precipitated in relation to the incipient opening of the hydrological system to percolating meteoric waters. The later fractures and associated breccias represent the late stages of the fault propagation. These structures (fractures 3, fractures 4 and the dilatant breccias B2) were formed when the extensional deformation reached the surface, resulting in an increasingly open hydrogeological system. At these stages, deposition of the dolomitic sediment DS and precipitation of the calcite cements C3, C4 and C5 show the circulation of freshwaters in a vadose meteoric environment, i.e. in karstic conditions.
ISSN: 0375-6742

hal-00512690
https://hal.archives-ouvertes.fr/hal-00512690
DOI : 10.1016/j.gexplo.2009.11.010

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Fractures or discontinuities perpendicular to the least stress σ3 were generated in a synthetic rock analogue (granular, frictional, cohesive, and dilatant) material in axisymmetric extension tests. These fractures are of two types defined by the mean stress σ. When σ is very small, the fractures form through the mode I cracking at tensile σ3 equal to the material tensile strength. The fracture walls have smooth surfaces. At higher σ, these surfaces become rougher, with the topography features forming faint or delicate plumose patterns. The amplitude of the plumose topography increases with σ. The axial stress σ3 at fracturing reduces in magnitude and changes in sign with the σ increase. Thus σ3 orthogonal discontinuities can form at compressive σ3. SEM observations show that these discontinuities are deformation localization bands where the material is characterized by the heterogeneous decohesion and volume and porosity increase due to dilatancy. The band thickness is several grain sizes. At formation, the bands are not opened, so they are not mode I fractures. They become fractures with plumose fractography after the separation of the sample parts along the band. The formation mechanism of these discontinuities or fractures is not completely clear, but it is suggested that it represents a running constitutive instability in the form of dilatancy banding (with further σ increase the bands become inclined to σ1, i.e., shear). The similarity between the experimentally generated plumose surface fractures and natural joints is discussed, and it is suggested that they can be formed as propagating constitutive instabilities.
ISSN: 0148-0227

hal-00585846
https://hal.archives-ouvertes.fr/hal-00585846
DOI : 10.1029/2010JB008104

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Both oedometric and plane-strain tests were performed with parallelepipedic samples made of synthetic granular, cohesive, frictional and dilatant rock analogue material GRAM2. For the first time parallel sets of fractures that have all the characteristics of natural joints were reproduced in the laboratory. The fractures are regularly spaced, normal to σ3, and have plumose morphology very similar to that of natural joints. These fractures can form at tensile stress σ3 much smaller in magnitude than the tensile strength of material and even at slightly compressive σ3. When mean stress σ exceeds a certain value, the fractures become oblique to σ1 (the obliquity increases with σ), forming networks of conjugate shear bands/fractures. These results of plane-strain experiments are in good agreement with those of better controlled conventional axisymmetric tests on a similar material in Chemenda et al. (2011b) and are closer to real geological situations. Both types of experiments are complementary. Their results lead to the conclusion that at least certain categories of natural fractures (including joints, and conjugate shear fractures/bands) were initiated as deformation localization bands. The band orientation is defined by the constitutive properties/parameters (notably the dilatancy factor) that are sensitive to σ.
ISSN: 0040-1951

hal-00795555
https://hal.archives-ouvertes.fr/hal-00795555
DOI : 10.1016/j.tecto.2011.11.021

Éditeur(s) : HAL CCSD Elsevier
Résumé : We present comparative field studies in folded areas (Southern France. Moroccan Western Atlas and Abruzzo, Italy) giving new insights into fracture distribution within folded rocks of the shallow brittle crust. We show that the curvature in folds formed in brittle mechanical units is usually accommodated by multiple "dip-domain boundaries" (appearing as curvature discontinuities at fold scale) corresponding to relatively narrow and dense fracture zones, striking parallel or slightly oblique to the fold axis. They separate "dip-domains" where curvature is absent or moderate. It is shown that the dip-domain boundaries (which are obvious in the case of kink folds or box-fold anticlines) are currently present as multiple subtle hinges even when the curvature appears continuous at first sight. The nature of dip-domain boundaries is studied, they often cut through the whole thickness of the mechanical units Their internal structure varies, and a non-exhaustive typology is proposed For each type, an interpretative kinematic scenario shows how the dip-domain boundaries could initiate and develop. We suggest two kinds of origins (1) they could correspond to the reactivation of inherited, along-strike fracture zones (opening-mode fracture concentrations such as big joints, fracture corridors. Inherited faults, etc), (2) they could be created as mechanical instabilities during the fold formation (syn-folding origin), in particular through small reverse faults. In both cases, early zones of weakness localize the dip-domain boundaries, and control the Increase in curvature in association with increasing fracture density within the boundary. Because they represent well-defined vertically and axially persistent sub-seismic fracture zones generally limited to the thickness of the folded unit, dip-domain boundaries could enhance the axial permeability of folded and fractured reservoirs.
ISSN: 0191-8141

hal-00512651
https://hal.archives-ouvertes.fr/hal-00512651
DOI : 10.1016/j.jsg.2010.03.002

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : Extension fractures of two types defined by the mean stress σ were generated in a synthetic rock analogue material. When σ is very small, the fractures are mode I cracks with smooth surfaces. At higher σ, these surfaces have plumose topography, with the amplitude increasing with σ. Both SEM observations and mechanical measurements show that fractures/discontinuities in the latter case are initiated as dilatancy localization bands. They form under tensile or slightly compressive normal stress and can be seen as running constitutive instabilities. The similarity between the plumose fractography of the experimental fractures and natural joints suggests similarity in the formation mechanism.
ISSN: 1631-0721

hal-00585886
https://hal.archives-ouvertes.fr/hal-00585886
DOI : 10.1016/j.crme.2011.01.002

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195degC to 268degC. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10-2 md for Y against 10-3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest that a similar relationship between kinematic markers and fault rock permeability anisotropy may be found in other fault zone types (reverse or strike-slip) affecting feldspar-rich lithologies in deep diagenesis conditions.
ISSN: 0149-1423

hal-00903428
https://hal.archives-ouvertes.fr/hal-00903428
DOI : 10.1306/03071312127

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Production rates in horizontal shale gas wells display declines that are controlled by the low permeability and the intrinsic heterogeneity of the shale matrix. We present an original multi-continuum approach that yields a physical model able to reproduce the complexity of the decreasing gas rates. The model describes the dynamics of gas rate as function of the physical reservoir parameters and geometry, while the shale matrix heterogeneity is accounted for by a stochastic description of transmissivity field. From the 3D (Dimensional) problem setting, including the heterogeneous shale matrix, the fractures generated by the hydrofracking operations, as well as the production well characteristics, we establish an effective upscaled 1D model for the gas pressures in fracture and matrix as well as the volumetric flux. We analyse the decline curves behaviour, and we identify the time scales that characterize the dynamics of the gas rate decline using explicit analytical Laplace space solutions of the upscaled process model. Asymptotically, the flux curves decrease exponentially, while in an intermediate regime we find a power-law behaviour, in which the flux scales with a power law in time as (t^{-beta }), where (beta ) reflects the medium heterogeneity. We use this solution to fit a set of real data displaying distinctly different decline trends and study the sensitivity of the model to the reservoir parameters in order to identify their respective controls at the different stages of the decline curve dynamics. Results indicate that the initial value of the gas rate is determined by the transmissivity of the fractures and the initial pressure of the gas in the shale matrix. The latter causes mainly a shift in the entire decline curve. The early time of decline curve shape is primarily controlled by the fracture properties (compressibility and transmissivity). During the main part of the economically valuable production times, i.e. before the production rate drops exponentially, the decline curve is strongly controlled by the properties of the shale rocks including their heterogeneity, which is modelled by two parameters describing the non-Fickian pressure diffusion effects in a stochastic framework.
ISSN: 0169-3913

hal-01217247
https://hal.archives-ouvertes.fr/hal-01217247
DOI : 10.1007/s11242-015-0504-y

Éditeur(s) : HAL CCSD Springer
Résumé : International audience
We present here a synthesis of the evolution of rifted continental margin systems in the Gulf of Aden. These margins are volcanic to the west of the Gulf of Aden, where they are influenced by the Afar hotspot, and non-volcanic east of longitude 46° E. The combined use of magnetics, gravity, seismic reflection, field observations (tectonic, stratigraphic and sedimentological) and oil well data allowed us to obtain better constraints on the timing of continental rifting and seafloor spreading. From the Permo-Triassic to the Oligocene, the Arabian-African plate was subject to distributed extension, probably due, at least from the Cretaceous, to tensile stresses related to the subduction of the Tethysian slab in the north. In Late Eocene-Early Oligocene, 34-33 Ma ago, rifting started to localise along the future area of continental breakup. Initially guided by the inherited basins, continental rifting then occurred synchronously over the entire gulf before becoming localised on the northern and southern borders of the inherited grabens, in the direction of the Afar hotspot. In the areas with non-volcanic margins (in the east), the faults marking the end of rifting trend parallel to the inherited grabens. Only the transfer faults cross-cut the inherited grabens, and some of these faults later developed into transform faults. The most important of these transform faults follow a Precambrian trend. Volcanic margins were formed in the west of the Gulf, up to the Guban graben in the southeast and as far as the southern boundary of the Bahlaf graben in the northeast. Seaward dipping reflectors can be observed on many oil industry seismic profiles. The influence of the hotspot during rifting was concentrated on the western part of the gulf. Therefore, it seems that the western domain was uplifted and eroded at the onset of rifting, while the eastern domain was characterised by more continuous sedimentation. The phase of distributed deformation was followed by a phase of strain localisation during the final rifting stage, just before formation of the Ocean-Continent Transition (OCT), in the most distal graben (DIM graben). About 20 Ma ago, at the time of the continental break-up, the emplacement of the OCT started in the east with exhumation of the subcontinental mantle. Farther west, the system was heated up by the strong influence of the Afar hotspot, which led to breakup with much less extension. In the Gulf of Aden (s.str), up to the Shukra El Sheik fracture zone, oceanic spreading started 17.6 Ma ago. West of this fracture zone, oceanic accretion started 10 Ma ago, and 2 Ma ago in the Gulf of Tadjoura. Post-rift deformation of the eastern margins of the Gulf of Aden can be seen in the distal and proximal domains. Indeed, the substantial post-rift uplift of these margins could be associated with either the continental break-up, or activity of the Afar hotspot and related volcanic/magmatic activity. Uplift of the northern proximal margin was still active (e.g. stepped beach rocks exposed at 60 m of 2 Ma; 30 m of 35,200 years; 10 and 2 m) and active volcanoes can be inferred at depths of between 70 and 200 km beneath the margin (at 5-10 km distance from the coast). On the distal margin, heat flow measurements show a high value that is associated with post-rift volcanic activity and the development of a volcano (with flows and sills) shortly after the formation of the OCT. The Afar hotspot is therefore important for several reasons. It allows the localisation of deformation along the Red Sea/Aden system and the rapid opening of the Gulf after the continental break-up; its influence also seems to persist during the post-rift period.
ISSN: 1866-7411

hal-01053089
https://hal.archives-ouvertes.fr/hal-01053089
DOI : 10.1007/s12517-011-0475-4

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
One of the main difficulties encountered when characterizing the hydrodynamic properties of a fractured aquifer is to identify the preferential flow paths within it. Different methods may be applied to determine the variability of the permeability at the borehole scale and to image the structure of the main flow zones between boreholes. In this paper, we compare the information obtained from different measurement techniques performed in a set of three 100 m depth wells (well-to-well spacing: 5­10 m) in a fractured crystalline rock setting. Geophysical logging and borehole-wall imaging are used to identify open and closed fractures intersecting the boreholes and their orientation. The comparison with flowmeter and single packer tests shows that few of the fractures interpreted as open from geophysical logs are significantly transmissive. Cross-borehole connectivity is first investigated from single packer tests with pressure monitoring in adjacent boreholes. To determine fracture zone connectivity, we propose a methodology simply based on the variation with packer depth of the ratio of the drawdown in the observation well and the drawdown in the pumping well. The results are compared to the analysis of cross-borehole flowmeter tests. We show that both methods provide consistent results with a similar level of information on connectivity.
ISSN: 0022-1694

insu-00221380
https://hal-insu.archives-ouvertes.fr/insu-00221380
DOI : 10.1016/j.jhydrol.2007.07.007

Éditeur(s) : HAL CCSD
Résumé : In order to minimize CO2 atmospheric concentration, a solution consists in sequestrating CO2 in geological reservoirs. To estimate long term risks, it is necessary to quantify the couplings between reaction processes as well as structural and hydrodynamical modifications. We realised two experimental benches enabling injecting CO2-enriched-brine in conditions corresponding to in situ storage (T < 200 oC and P < 200 bar) and developed
an experimental protocol using X-Ray microtomography and fluid and rock analyses in order to measure the variations of physical and chemical parameters.
The study of carbonated reservoirs near the injection well, allows quantifying different k-phi relationships depending on the dissolution processes and triggered by the local fluid chemical composition and initials conditions. Away from the injection well, we observe carbonate precipitation decreasing the permeability. The study of fracturated caprock samples shows that alternative percolation of CO2-enriched-brine and CO2 gas increases the fracture permeability.
The study of silicated rocks indicates carbonate precipitation in zeolite sandstone and sintered dunite grains. Nevertheless, in zeolite sandstone we also observe the precipitation of clay particles located in the uid pathways which decrease strongly the permeability.
Afin de minimiser la concentration en CO2 dans l'atmosphère une solution consiste à le séquestrer dans les réservoirs géologiques. Pour évaluer les risques à long terme, il est nécessaire de quantifier les couplages entre les processus réactionnels et les modifications structurales et hydrodynamiques. Dans cette optique, nous avons construit deux dispositifs expérimentaux permettant d'injecter des saumures chargées en CO2 dans les conditions de stockage (T < 200 °C et P < 200 bar) et mis en oeuvre un protocole expérimental utilisant la microtomographie RX et l'analyse des roches et des fuides pour quantifier les variations des paramètres physiques et chimiques. Dans le cas des réservoirs carbonatés, on observe, près du puits d'injection, une forte variabilité des relations k-phi en fonction du régime de dissolution contrôlé par la chimie locale du fluide, ainsi que par les conditions initiales. A plus grande distance, on observe des processus de précipitation diminuant fortement la perméabilité. L'étude des roches de couverture fracturées (argilite) a montré qu'une percolation alternée d'une saumure chargée en CO2 et de CO2 gaz augmentait la perméabilité de fracture. Dans le cas des roches silicatées, la précipitation de carbonates est mise en évidence aussi bien dans les grès à zéolites que dans les frittés de dunite de San Carlos. Cependant, dans les grès à zéolites, la précipitation d'une phase argileuse est observée dans les chemins d'écoulement et engendre une forte diminution de la perméabilité.
https://tel.archives-ouvertes.fr/tel-00416408

tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408/document
https://tel.archives-ouvertes.fr/tel-00416408/file/These_Luquot.pdf

Éditeur(s) : HAL CCSD Techno-Press
Résumé : Fractures and faults riddle the Earth’s crust on all scales, and the deformation associated with them is presumed to have had significant effects on its petrological and structural evolution. However, despite the abundance of directly observable earthquake activity, unequivocal evidence for seismic slip rates along ancient faults is rare and usually related to frictional melting and the formation of pseudotachylites. We report novel microstructures from garnet crystals in the immediate vicinity of seismic slip planes that transected lower crustal granulites during intermediate-depth earthquakes in the Bergen Arcs area, western Norway, some 420 million years ago. Seismic loading caused massive dislocation formations and fragmentation of wall rock garnets. Microfracturing and the injection of sulfide melts occurred during an early stage of loading. Subsequent dilation caused pervasive transport of fluids into the garnets along a network of microfractures, dislocations, and subgrain and grain boundaries, leading to the growth of abundant mineral inclusions inside the fragmented garnets. Recrystallization by grain boundary migration closed most of the pores and fractures generated by the seismic event. This wall rock alteration represents the initial stages of an earthquake-triggered metamorphic transformation process that ultimately led to reworking of the lower crust on a regional scale.
ISSN: 2287-528X

hal-01553309
https://hal.archives-ouvertes.fr/hal-01553309
https://hal.archives-ouvertes.fr/hal-01553309/document
https://hal.archives-ouvertes.fr/hal-01553309/file/austrheim2017.pdf
DOI : 10.1126/sciadv.1602067

Éditeur(s) : HAL CCSD American Association for the Advancement of Science
Résumé : 6 pages
International audience
Large impacts provide a mechanism for resurfacing planets through mixing near-surface rocks with deeper material. Central peaks are formed from the dynamic uplift of rocks during crater formation. As crater size increases, central peaks transition to peak rings. Without samples, debate surrounds the mechanics of peak-ring formation and their depth of origin. Chicxulub is the only known impact structure on Earth with an unequivocal peak ring, but it is buried and only accessible through drilling. Expedition 364 sampled the Chicxulub peak ring, which we found was formed from uplifted, fractured, shocked, felsic basement rocks. The peak-ring rocks are cross-cut by dikes and shear zones and have an unusually low density and seismic velocity. Large impacts therefore generate vertical fluxes and increase porosity in planetary crust.
ISSN: 0036-8075

hal-01399386
https://hal.archives-ouvertes.fr/hal-01399386
PUBMED : 27856906
DOI : 10.1126/science.aah6561

Éditeur(s) : HAL CCSD Elsevier
Résumé : The Erro-Tobbio peridotites (Voltri Massif, Ligurian Alps) represent subcontinental lithospheric mantle tectonically exhumed during Permo-Mesozoic extension of the Europe-Adria lithosphere. Previous studies have shown that exhumation started during Permian times, and occurred along kilometer-scale lithospheric shear zones which enhanced progressive deformation and recrystallization from spinel- to plagioclase-facies conditions. Ongoing field and petrologic investigations have revealed that the peridotites experienced, during uplift, a composite history of diffuse melt migration and multiple episodes of ultramafic-mafic intrusions. In this paper we present the results of field, structural and petrologic-geochemical investigations into a sector of the Erro-Tobbio peridotite unit that preserves well this multiple intrusion history. Melt impregnation in the peridotites is evidenced by significant plagioclase enrichment and crystallization of unstrained orthopyroxene replacing kinked mantle olivine and clinopyroxene; impregnating melts were thus opx-saturated. Melt-rock interaction caused chemical changes in mantle minerals (e.g. Al decrease and REE increase in cpx; Ti and Cr# enrichment in spinel). Nevertheless, clinopyroxenes still exhibit LREE depletion (Ce;N;/Sm;N; = 0.006-0.011), indicating a depleted signature for the percolating melts. Melt impregnation was thus related to diffuse porous flow migration of depleted MORB-type melt fractions that modified their compositions towards opx saturation by mantle-melt interaction during ascent. The impregnated peridotites are intruded by a hectometer-scale stratified cumulate body, mostly consisting of troctolites and plagioclase wehrlites, showing gradational, interfingered contacts with the host mantle rocks. Subsequent intrusion events are revealed by the occurrence of olivine gabbros as decameter-wide lenses, variably thick (centimeter- to meter-scale) dykes and thin dykelets, which crosscut both the peridotite foliation and the magmatic layering in the cumulates. Overall, major and trace element compositions of minerals in the intrusives indicate that they represent variably differentiated cumulus products crystallized from rather primitive N-MORB-type aggregated melts. Slightly more evolved compositions are shown by olivine gabbros, relative to the troctolites and plagioclase wehrlites of the cumulate body. Mineral chemistry features (e.g. the Fo-An correlation and high Na, Ti, Mg# in cpx) indicate that the studied intrusive rocks crystallized at moderate pressure conditions (3-5 kbar, i.e. 9-15 km depth). Our study thus points to a progressive transition from porous flow melt migration to emplacement of magmas in fractures, presumably related to progressive change of lithospheric mantle rheology during extension-related uplift and cooling.
ISSN: 0024-4937

hal-00407669
https://hal.archives-ouvertes.fr/hal-00407669
DOI : 10.1016/j.lithos.2006.06.014

Éditeur(s) : HAL CCSD
Résumé : International audience
The geology of the North Pyrenean Zone in the central Pyrenees allows for the observation in the field of theentire section of the Pyrenean rift, from the mantle to the crust and the Mesozoic cover (pre, syn and post rift).The good knowledge we have of the pre-Alpine history of the Pyrenees allows us to properly constrain the Alpinegeological evolution of the pre-Triassic rocks which record both Variscan and Alpine orogenic cycles.The mantle outcrop as kilometric to centimetric fragments of peridotite dispersed within a carbonate metamorphicbreccia. The study of peridotite serpentinisation shows several events of low-temperature serpentinisation, incontact with seawater. In some locallities, we can observe a mixture of fragments of variously serpentinizedperidotites. This suggests a tectonic context where fragments of peridotites from different structural levels weresampled more or less synchronously.The granulitic basement is characterized by a Variscan syndeformational HT event (300-280 Ma). So farwe have not found any trace of a Cretaceous HT event (> 500C). On the other hand, the basement is affectedby a regional metasomatism that began during the Jurassic and became more spatially focused with time until itwas restricted to the Pyrenean rift during the Aptien, Albian and Cenomanian. The talc-chlorite metasomatism(120-95 Ma) shows an evolution from a static toward a syn-deformation hydrothermal event, under a more or lessnormal geothermal gradient. Extensional deformation is recorded by the reworking of several inherited low-angleVariscan tectonic contacts, but also by dispersed high-angle extensional shear zones formed under greenshistconditions.The metamorphic Mesozoic cover of the basement massifs, which constitute the so-called Internal MetamorphicZone, is an allochtonous unit made of lenses of Mesozoic rocks enclosed into the breccia, whichlocally contains peridotite and basement clasts. The Mesozoic metamorphic carbonates show a first phase ofsyn-metamorphic (450-600C, P < 2 kb) ductile deformation, and subsequent phases of folding and fracturing.The datation of neoformed minerals give a 108-85 Ma time span for the metamorphism. We interpret this brecciaas an abandonment breccia which marks the emergence of the main detachment. The basal contact of the Mesozoiccover has a complex 3D geometry traced by Triassic evaporites. It corresponds to a major pre- and synorogenicpolyphased tectonic contact.All these data show a geometrically complex hyper-extended rift where the crust was not stretched under ahigh geothermal gradient but thinned by the tectonic extraction of relatively thin lenses and perhaps cut by highangle low-grade shear zones. The 3D geometry, as well as the strain records and the breccia lithologies stronglysuggest a non-cylindricity for the exhumation process, probably within a transtentional system
Geophysical Research Abstracts
Vienne, Austria

insu-01510371
https://hal-insu.archives-ouvertes.fr/insu-01510371