Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Both oedometric and plane-strain tests were performed with parallelepipedic samples made of synthetic granular, cohesive, frictional and dilatant rock analogue material GRAM2. For the first time parallel sets of fractures that have all the characteristics of natural joints were reproduced in the laboratory. The fractures are regularly spaced, normal to σ3, and have plumose morphology very similar to that of natural joints. These fractures can form at tensile stress σ3 much smaller in magnitude than the tensile strength of material and even at slightly compressive σ3. When mean stress σ exceeds a certain value, the fractures become oblique to σ1 (the obliquity increases with σ), forming networks of conjugate shear bands/fractures. These results of plane-strain experiments are in good agreement with those of better controlled conventional axisymmetric tests on a similar material in Chemenda et al. (2011b) and are closer to real geological situations. Both types of experiments are complementary. Their results lead to the conclusion that at least certain categories of natural fractures (including joints, and conjugate shear fractures/bands) were initiated as deformation localization bands. The band orientation is defined by the constitutive properties/parameters (notably the dilatancy factor) that are sensitive to σ.
ISSN: 0040-1951

hal-00795555
https://hal.archives-ouvertes.fr/hal-00795555
DOI : 10.1016/j.tecto.2011.11.021

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Networks of localized conjugate compactive shear bands with large dihedral angles (corresponding to so-called shear-enhanced compaction bands) were generated in 3-layer plane strain finite-difference models. The central layer has elastic–plastic properties with a small positive internal friction coefficient, negative dilatancy factor, and the hardening modulus reducing during the deformation. The two other layers are elastic. The spatial organization of the networks in the central layer, resulting from the elastic–plastic instability of the 3-layer system, was shown to be dependent on the contrast of the elastic stiffness of the layers and on the friction between them. When the stiffness E of the elastic layers and/or the friction are small, the networks are rather symmetric (the bands of both orientation families are distributed homogeneously within the layer). An increase in E at high friction, results in the clustering of the bands of one orientation along a layer segment which is followed by another segment filled with the bands of the other orientation. Different network types are characterized by different band spacing which is smaller in the clustered networks. The intensity of inelastic deformation and hence of porosity reduction within the bands are also smaller in this case. The obtained band networks are very similar to those in nature where the same variability of the network organization is observed. Available geological and mechanical data confirm the conclusions from the modeling about the origin of this variability.
ISSN: 0040-1951

hal-01116201
https://hal.archives-ouvertes.fr/hal-01116201
DOI : 10.1016/j.tecto.2014.01.021

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Phyllosilicate content and related permeability of fault zones form primary controls on hydraulic and mechanical behavior of the brittle crust. Hence, understanding and predicting the localization of these ubiquitous minerals is a major issue for fundamental and applied geosciences. We describe normal fault zones cutting a foreland arkosic turbiditic formation suffering high-T diagenesis and formed under conditions (~200°C) typical of deeply buried reservoirs and common within the seismogenic interval. Microstructural analyses show a large proportion of phyllosilicates (up to 34%) in the fault rock, derived from near-complete feldspar alteration and disaggregation during deformation. This study shows that even faults with offsets (~20 cm) much lower than bed thickness can have such large feldspar-to-phyllosilicate transformation ratios, implying that the origin of the phyllosilicates is purely transformation related. These results imply that the potential sealing capacity and strength of faults could be predicted from the host rock feldspar content. Where sealing capacity and fault strength can be related to phyllosilicate content, these properties can then also be inferred from the predicted phyllosilicate content: this opens up new horizons concerning the hydraulic and the mechanical behavior of the upper crust.
ISSN: 0094-8276

hal-00903574
https://hal.archives-ouvertes.fr/hal-00903574
DOI : 10.1002/grl.50829

Éditeur(s) : Marine Biological Laboratory
Résumé : Hydrothermal vent tubeworms, Riftia pachyptila Jones, were maintained alive and studied on board ship using flow-through pressure aquaria. Simultaneous measurements of O2, SIGMA-CO2, SIGMA-H2S fluxes showed that the intact symbioses reach maximum rates of uptake of SIGMA-CO2 (>2 mu-mole g-1 h-1) at about 90 mu-M SIGMA-H2S. Measurements were made of hemolymph and coelomic fluid SIGMA-CO2, SIGMA-H2S, thiosulfate, pH, and hemoglobin concentrations in worms kept under various conditions of O2 and SIGMA-H2S. Normal hemolymph pH appears to be about 7.5 and is not affected by SIGMA-H2S and SIGMA-CO2 concentrations within the ranges observed. We conclude that Riftia is specialized to provide sulfide to its symbionts with minimal interaction of sulfide with the animal metabolism. The uptake of sulfide is apparently by diffusion into the hemolymph, facilitated by the sulfide-binding properties of the hemoglobins. Both SIGMA-CO2 and P(CO2) are elevated in the hemolymph above their levels in the medium, although they are reduced under autotrophic conditions. Thus inorganic carbon is apparently concentrated from the medium into the hemolymph by an unknown mechanism.
Biological Bulletin (0006-3185) (Marine Biological Laboratory), 1991-02 , Vol. 180 , N. 1 , P. 135-153

Droits : 1991 Marine Biological Laboratory
http://archimer.ifremer.fr/doc/00178/28970/27392.pdf
DOI:10.2307/1542437
http://archimer.ifremer.fr/doc/00178/28970/

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0

Éditeur(s) : HAL CCSD
Résumé :  
Improvement of wood quality related traits is currently hampered by costly chemical and technological assays and the necessity to wait until the trees are nearly mature to evaluate wood properties. The availability of a vast quantity of genomic data opens now a new avenue to identify early selection criteria based on molecular information and therefore increase selection efficiency. Association mapping is becoming a method of choice to identify QTN (quantitative trait nucleotide) that contribute to complex trait variation. The implementation of this approach requires on the one hand knowledge of the molecular mechanisms underlying trait variation and polymorphism within candidate genes, and on the other hand the availability of phenotypically well characterized genetic material. We are developing this strategy in the frame of the French maritime pine breeding program, an economically important forest tree species in the South Western Europe. About 500 trees from the breeding population were evaluated for wood physical and chemical properties through the analysis of 2,800 half-sib progenies and 1,500 clones in 8 field tests. These same trees are being genotyped at 185 SNPs obtained from the sequencing of 41 candidate genes, and an additional set of 200 eSNPs detected in 147 EST-contigs (to be used as control). Statistical association between the breeding values of the 500 trees and their respective genotypes will be tested using mixed models accounting for relatedness among individuals of the breeding population.
IUFRO-CTIA joint conference, "Adaptation, Breeding and Conservation in the Era of Forest Tree Genomics and Environmental Change"
Québec City, Canada

hal-01032075
https://hal.archives-ouvertes.fr/hal-01032075

Éditeur(s) : HAL CCSD Humana Press
Résumé : International audience
The sodium-proton exchanger 1 (NHE-1) is a membrane transporter that exchanges Na(+) for H(+) ion across the membrane of eukaryotic cells. It is cooperatively activated by intracellular protons, and this allosteric regulation is modulated by the biophysical properties of the plasma membrane and related lipid environment. Consequently, NHE-1 is a mechanosensitive transporter that responds to osmotic pressure, and changes in membrane composition. The purpose of this study was to develop the relationship between membrane surface tension, and the allosteric balance of a mechanosensitive transporter such as NHE-1. In eukaryotes, the asymmetric composition of membrane leaflets results in a difference in surface tensions that is involved in the creation of a reservoir of intracellular vesicles and membrane buds contributing to buffer mechanical constraints. Therefore, we took this phenomenon into account in this study and developed a set of relations between the mean surface tension, membrane asymmetry, fluid phase endocytosis and the allosteric equilibrium constant of the transporter. We then used the experimental data published on the effects of osmotic pressure and membrane modification on the NHE-1 allosteric constant to fit these equations. We show here that NHE-1 mechanosensitivity is more based on its high sensitivity towards the asymmetry between the bilayer leaflets compared to mean global membrane tension. This compliance to membrane asymmetry is physiologically relevant as with their slower transport rates than ion channels, transporters cannot respond as high pressure-high conductance fast-gating emergency valves.
ISSN: 1085-9195

inserm-00871709
http://www.hal.inserm.fr/inserm-00871709
http://www.hal.inserm.fr/inserm-00871709/document
http://www.hal.inserm.fr/inserm-00871709/file/art_3A10.1007_2Fs12013-012-9340-7.pdf
DOI : 10.1007/s12013-012-9340-7

Éditeur(s) : HAL CCSD
Résumé : International audience
In this paper, we focus on the very specificity of rumors as pieces of information for modeling their process of propagation. We consider a population of pedestrians walking in a city and we assume that a rumor is transmitted by word of mouth from one to another. Although the diffusion of a rumor is of course a multi-dimensional process driven by sociological, economical and psychological elements, in this first step, we emphasize one main dimension of this complex phenomenon only. This dimension is the neighborhood of individuals likely to spread the information. With a confrontation of two antagonistic properties of the neighborhood that are profusion and scarcity of spreaders, we highlight specific characteristics of rumors. This study could lead to the psychological mechanism involved in the decision for a person to become or not a spreader himself/herself. In summary, we study if scarcity could be the silver bullet explaining how a rumor spreads.
ASONAM 2015 : IEEE/ACM International Conference on Advances in Social Networks Analysis and Mining
Paris, France

hal-01252936
https://hal.archives-ouvertes.fr/hal-01252936
DOI : 10.1145/2808797.2809299

Éditeur(s) : HAL CCSD
Résumé : International audience
(Guava (Psidium guajava L.) is a tropical fruit widely consumed around the world. The study wascarried out on four selected guava varieties grown in Martinique. Two fruit harvests were gathered at two-yearintervals, at the green/yellow color change maturity stage. First, we established the homogeneity of all fruitbatches by bootstrapping, ANOVA, box plot and multiple comparison statistical analysis on physicalparameters. Red Supreme Ruby clearly differs from the other three varieties, whereas the results for CentenoProlific are between Beauséjour and Enana Cuba. We determined on puree obtained from a homogeneousbatch of each variety the physicochemical and functional properties as well as the antioxidant properties. Ourresults show that the combination of lycopene and vitamin C, and their synergistic mechanisms in the fruitextracts may be responsible for the high antioxidant activity of guava puree, and we demonstrate a statisticallysignificant positive correlation between EC50 and lycopene.
IOSR Journal of Environmental Science, Toxicology and Food Technology (IOSR-JESTFT)

hal-01672064
https://hal.univ-antilles.fr/hal-01672064
DOI : 10.9790/2402-1109015767

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We use 3-D mechanical modeling representing faults as planar surfaces with frictional properties that obey Coulomb-failure process to explore the long-term slip rates of the Altyn Tagh fault and Kunlun faults in the north Tibetan plateau. Crustal theology is simplified as an elastoplastic upper crust and a viscoelastic lower crust. Far-field GPS velocities and late Quaternary fault slip rates are used to constrain the model results. Rheological tests show that effective fault friction lower than 0.1-0.08 leads to high slip rates that fit with geologically and geodetically determined slip rates of the Kunlun fault (10-11.7 +/- 1.5 mm/yr). Meanwhile, the modeled Altyn Tagh fault reaches slip rates similar to 13.7 mm/yr to similar to 7.8 mm/yr in its central portion, between ranges of the geological slip rates. Associated with high slip rates, our model predicts that central Tibet (similar to 84 degrees E-95 degrees E) from the Altyn Tagh fault to the north of the Himalayan arc accommodates north-south shortening and east-west extension rates of similar to 10-12 mm/yr and similar to 8-10 mm/yr, respectively. We also question the widely accepted idea that interseismic strain is driven at the base of the seismogenic zone by a screw dislocation. If this assumption fails, the presented model implies that interseismic strain around large strike-slip faults could be distributed in a much broader way if the lithosphere deforms as a thin elastic plate rather than an elastic half-space with an embedded dislocation. If this distributed deformation is ignored, and the instantaneous surface deformation field modeled as that resulting from slip on a dislocation below a specified depth embedded in an elastic half-space, the estimated slip rate will inevitably be lower than the true long-term slip rate. This appears to explain why geodetic slip rates proposed for the Altyn Tagh fault (510 mm/yr) are lower than some of the geological slip rates. (C) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00411926
https://hal.archives-ouvertes.fr/hal-00411926
DOI : 10.1016/j.epsl.2008.06.049

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Seventy percent of breast tumors express the estrogen receptor (ER), which is generally considered to predict a better outcome relative to ER-negative tumors, as they often respond to antiestrogen therapies. During cancer progression, mammary tumors can escape from estrogen control, resulting in the acquisition of invasive properties and resistance to treatment. ER expression is a dynamic phenomenon and is finely regulated at numerous levels, including the gene, mRNA, and protein levels. As a consequence, many molecular mechanisms have been implicated in modulating ER activity and estrogen signaling in mammary cancer. In fact, one-third of ER-positive breast cancer cells do not respond to first-line endocrine therapies, and a large subset of relapsing tumors retain ER expression. Increased knowledge of these mechanisms has led to the development of better prognostic methods and targeted therapies for patients; however, additional research is still needed to improve patient survival. In this chapter, we focus on the signaling pathways leading to changes in or loss of ER activity in breast cancer progression.
ISSN: 0083-6729

hal-00874313
https://hal.archives-ouvertes.fr/hal-00874313
DOI : 10.1016/B978-0-12-416673-8.00004-6
PUBMED : 23810005

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A hallmark of living systems is the management and the storage of information through genetic and epigenetic mechanisms. Although the notion of epigenetics was originally given to any regulation beyond DNA sequence, it has often been restricted to chromatin modifications, supposed to behave as cis-markers, specifying the sets of genes to be expressed or repressed. This definition does not take into account the initial view of epigenetics, based on nonlinear interaction networks whose "attractors" can remain stable without need for any chromatin mark. In addition, most chromatin modifications are the steady state resultants of highly dynamic modification and de-modification activities and, as such, seem poorly appropriate to work as long-term memory keepers. Instead, the basic support of epigenetic memory could remain the attractors, to which chromatin modifications belong as do many other components. The influence of chromatin modifications in memory is highly questionable when envisioned as static structural marks, but can be recovered under the dynamic circuitry perspective, thanks to their self-templating properties. Beside their standard repressive or permissive functions, chromatin modifications can also influence transcription in multiple ways such as: (1) by randomizing or inversely stabilizing gene expression, (2) by mediating cooperativity between pioneer and secondary transcription factors, and (3) in the hysteresis and the ultrasensitivity of gene expression switches, allowing the cells to take unambiguous transcriptional decisions.
ISSN: 1420-682X

hal-01063617
https://hal.archives-ouvertes.fr/hal-01063617
DOI : 10.1007/s00018-012-0923-7
PUBMED : 22331281

Éditeur(s) : HAL CCSD
Résumé :  
The gelatinous layer (G-layer) of tension wood fibres in hardwood contributes to the mechanical function of the living tree and has significant consequences on properties of solid wood. Its size, shape and structure observed by optical or electron microscopy exhibits characteristic anatomical features. However, we found that sectioning of non-embedded wood samples results in an uncontrolled swelling of the G-layer was monitored by serial sections, from an embedded wood sample, from its trimmed transverse face to that located several hundreds of micrometers deep. The results revealed that the initial cutting before embedding produced a border effect responsible for the swollen nature, which is similar to sections from non-embedded material. After a conventional embedding technique was applied, a section of at least 30 micrometres below the trimming surface is required to observe an un-swollen G-layer.
IAWA Journal

hal-01032054
https://hal.archives-ouvertes.fr/hal-01032054

Éditeur(s) : HAL CCSD
Résumé : We present an experimental study of relations between hydraulic properties of clayey rocks and their deformation at bulk and micro scale. The experimentation is based on triaxial deformation of kaolinitic core samples, on permeability measurements, and on several methods of analysis of the microstructure. To produce the samples, remoulded kaolinite material is consolidated by axial loading up to 20 MPa in an oedometric cell. Then, in a triaxial cell, an undrained stress path is applied in order to induce shearing damage in the sample. The permeability of the sample is measured by fluid flow across the sample. Before and after these hydro-mechanical tests, the evolution and the homogeneity of the pore space and moreover the texture of the material are analysed by X-ray tomography, environmental scanning electron microscopy and thermic neutron diffraction. Contrary to expectations, the permeability at the sample scale does not vary significantly, although quite large deformation is reached. The final deformation is heterogeneous, with well-developed shear bands. It appears that the development of compacting and dilating zones generates a heterogeneous permeability field, which results in a negligible variation of the bulk permeability at the sample scale.
International Journal of Rock Mechanics and Mining Science

hal-00496407
https://hal.archives-ouvertes.fr/hal-00496407
DOI : 10.1016/j.ijrmms.2010.04.007

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Tangential strains were measured with strain gauges at the surface of xylem and inner bark of saplings of Cryptomeria japonica D. Don. and Fagus silvatica L. during a pressurization test. The test consists in submitting the whole sapling to an artificially imposed hydrostatic pressure of increasing magnitude. The elastic response of the stems was found linear both at the surface of xylem and inner bark. A simple geometric model allows to compute radial strains in each tissue from tangential strain data. Inside inner bark, radial strains are much larger than tangential strains, because tangential strains are restrained by the core of wood. The material compliance of each tissue was computed as the ratio between the radial strain and the pressure that caused it. The material compliance of xylem is much lower than that of inner bark, but, as its thickness is much larger, its contribution to the apparent behavior of the stem is not negligible. Computation of material compliances by this pressurization test provides information about the specific behavior of each tissue in response to hydrostatic pressure. This can be used to estimate and interpret the calibration factor linking the water status of the plant to the apparent strain measured at its surface.
ISSN: 0931-1890

hal-01031900
https://hal.archives-ouvertes.fr/hal-01031900
DOI : 10.1007/s00468-006-0061-7

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
The hydrogen content of nominally anhydrous minerals is of great interest, because it can influence many physical and mechanical properties of mantle rocks. Moreover, the hydrogen diffusion profiles can be used to constrain timescales related to magma eruptions. Here, we report models of ionic diffusion for trace elements in anisotropic crystals and apply them to hydrogen diffusing out of mantle-derived olivine. We first compare and discuss the characteristics of 1D and 3D models and show that only 3D anisotropic diffusion models can lead to diffusion profiles exhibiting non-equilibrium plateau at the center of the solid along the slowest axis, as measured in natural samples. In a second part, we discuss the differences between hydration and dehydration of olivine for diffusion that is linked to two different atomic sites involved in hydrogen mobility. Finally, we apply our 3D anisotropic model to previous results on mantle-derived olivine from Pali-aike to better characterize diffusion coefficients and their anisotropy that could be relevant for dehydration of olivine. Our results show that dehydration has to be strongly anisotropic, with a fast [100] axis and a significantly slower [001] axis.
ISSN: 0342-1791

hal-01115253
https://hal.archives-ouvertes.fr/hal-01115253
DOI : 10.1007/s00269-014-0685-x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Carbonation of peridotite is a widespread process in nature, with emerging societal and environmental implications through geological storage of CO2. We studied the micro- and nano-scale structures associated with the carbonation of peridotite pervaded by a CO2-rich water and the induced changes of its hydrodynamic properties. Focused ion beam (FIB) nanotomography was coupled with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations. An experimental sample of dunite core percolated by a CO2-rich fluid (pCO2 = 11 MPa) at 160 °C was compared with a naturally carbonated sample from the Atlantic Ridge (Exp. IODP 304). Results of the 8-days percolation experiment show continuous alteration of olivine into magnesite locally associated with a poorly crystalline serpentine-type mineral referred to as proto-serpentine. The experiment is also characterized by an overall decrease in rock porosity (from 7.7 to 6.4%) and permeability (from 8.5 × 10− 16 to 1.7 × 10− 16 m2). The primary inter-granular porosity (1 to 10 μm) is progressively filled with magnesite, leading to the overall decrease of permeability. At the same time, a secondary small-scale porosity (10 nm to 1 μm) is created at the tip of the dissolution features along the (010) cleavage planes of olivine grains. Carbonate crystals grow within these etch-pit structures behind the dissolution front. Dissolution and precipitation occur at a relative rate that maintains the secondary porosity over the timescale of the experiment (i.e. carbonate growth has to be the slowest one). This process is interpreted as an interface coupled dissolution-precipitation mechanism of olivine carbonation. Proto-serpentine is only formed in highly reduced flow areas, such as small olivine etch-pits (10 to 500 nm wide), which are more isolated from CO2 input. SEM-FIB analyses show the 3D preferential orientation of the dissolution-precipitation planes within a given olivine grain. It suggests the formation of lateral connections between the etch-pits (infra-micrometric “channels”) providing access to reactants and removing reaction products at the reaction sites. The experimental results show that olivine dissolution and magnesite precipitation converge to a quasi-steady state resulting in a constant carbonation rate controlled by reaction kinetics and not by mass transfer for this flow regime. The system self-regulates, independently of the porosity change at least during this incipient stage of olivine carbonation. Similar textures are observed in natural samples collected at 170 m-depth in the vicinity of veinlets driving late fluids down into the cooling oceanic lithosphere. This suggests that similar mechanisms are active in nature and can play an important role in the late, low temperature alteration stages of fractured peridotite. These results also highlight the critical role of nm-scale spatial arrangement of dissolution and precipitation features on mass transfers and on the sustainability of olivine carbonation through coupled dissolution-precipitation processes.
ISSN: 0009-2541

hal-01684733
https://hal.archives-ouvertes.fr/hal-01684733
DOI : 10.1016/j.chemgeo.2017.11.013

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Anisotropy of low-field magnetic susceptibility (AMS) of basaltic lava flows can give some clues about post-emplacement tilting occurring in volcanic sequences. Such a study has been carried out on a sequence of 19 successive lava flows from Kerguelen Archipelago. Surprisingly, two different patterns were observed. The first one - herein called normal fabric - is consistent with the lava-flow direction inferred from geological observations, whereas the second one observed for about 70 per cent of the analysed samples - herein called abnormal fabric - appears to be unrelated to the shear history of the lava flows during their emplacements. These abnormal fabrics are not strictly inverse fabric but seem to have a more complex origin. The unusual nature of these abnormal fabrics has been confirmed by lattice preferred orientation of plagioclases obtained from high-resolution electron backscattered diffraction measurements. The aim of this study is to propose a physical interpretation of these fabrics. A first step in our understanding was to clearly identify the nature and the magnetic properties of the Fe-Ti oxides assemblage. Thus, we present a comprehensive rock magnetic analysis relying on low- and high-temperature thermomagnetic curves (K-T), crossover diagrams, first-order reversal curves, ore-microscopy, Mössbauer measurements and electron backscattered images. We found that in the present case the abnormal fabrics are probably linked to a mixture of prevailing single domain (SD) strongly interacting grains population and a subsidiary multidomain grains population. SD grains are identified as small magnetite crystallized within the interstitial glass in globular aggregates along the silicate framework. Then a question arises: to what extent such SD interacting grains in globular aggregates can affect the magnetic susceptibility and its anisotropy? To answer this question, we developed a physical model in which the total energy density of an SD grain with an uniaxial anisotropy is minimized. In this model, the distribution function of the direction of the magnetic interaction field is comprised between two boundary states. It is either isotropic, which formally corresponds to the thermal demagnetized state, or it is ordered, which formally corresponds to the Alternative Field demagnetized state. We show that in both cases the degree of anisotropy decreases as the interaction field increases. Thus, we conclude that the abnormal fabric encountered in this study can be simply explained by strong magnetostatic interactions that would explain the large scattering of AMS often observed in basaltic lava flows.
ISSN: 0956-540X

hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449/document
https://hal.archives-ouvertes.fr/hal-00716449/file/gji-S-12-HAL.pdf
DOI : 10.1111/J.1365-246X.2012.05421.X

Éditeur(s) : HAL CCSD American Geophysical Union (AGU) American Geophysical Union
Résumé : International audience
Environmental magnetism of speleothems is still in its early stage of development. Here we report on our investigation of the environmental and paleomagnetic information that has been recorded in speleothems, and what are the factors that control its preservation and reliability. To address these issues, we used a multidisciplinary approach, including rock magnetism, petrography, scanning electron microscopy, stable carbon and oxygen isotope compositions, and major and trace element concentrations. We applied this to a set of samples from different stages of speleothem evolution: present-day dripwater (glass plates), a weathered stalactite, a fresh stalagmite, cave sediments, and terra rossa soils. These samples come from the Penico and Excentricas caves, located in two distinct aquifers of the Algarve region, South Portugal. Our results show that the main magnetic carriers of the speleothems under study are primary (detrital) and consist of maghemite (and magnetite?). Similarities in coercivity and temperature dependence of the studied set of samples suggest that iron oxides are inherited from the terra rossa soils that cap the cave and were transported to the speleothems by dripwater. Hence, they represent a regional environmental signature. Interestingly, a stable and probably detrital remanent magnetization could be isolated in the fresh stalagmite, whereas the weathered stalactite yielded chaotic magnetic directions and very low remanent intensities. We propose that these low intensities can be the result from (i) different remanence acquisition mechanisms between stalagmite and stalactite and/or (ii) iron dissolution by fungal activity. We also suggest that magnetic properties and color and the content in detrital elements in the fresh speleothem inform about environmental processes acting on the interface of rock (soil)-atmosphere, while oxygen isotope composition and alkaline-earth element concentrations inform about calcite-water interaction processes. These results provide a better understanding of how environmental information is recorded in speleothems and what the factors are that control the reliability of the paleomagnetic and paleo-environmental signal.
ISSN: 0148-0227

hal-01114953
https://hal.archives-ouvertes.fr/hal-01114953
DOI : 10.1002/2014JB011381