Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either “artificially”, or by natural extractives.
Wood Science and Technology

hal-01096868
https://hal-agroparistech.archives-ouvertes.fr/hal-01096868
DOI : 10.1007/S00226-010-0393-8

Éditeur(s) : HAL CCSD
Résumé : This paper presents a collection of wood species with important uses in musical instruments, in reference to historical and geographical cultural specificities, with ranges of viscoelastic vibrational properties by species. Data combine our experimental characterizations and extensive literature review, gathered in a specific relational database. An overview of vibrational properties' distribution on c.400 species is introduced. Two case studies of wood choices for a given function in different epochs or regions are presented: woods for European historical bows, and woods for idiophone bodies in different continents. Trends are contrasted: very different properties associated to historical changes in the first case; some common features over different regions in the second one.
Proceedings of the International Conference of COST Action IE0601 Wood Science for the Preservation of Cultural Heritage
Braga, Portugal

hal-00808403
https://hal.archives-ouvertes.fr/hal-00808403
https://hal.archives-ouvertes.fr/hal-00808403/document
https://hal.archives-ouvertes.fr/hal-00808403/file/Vibrational_properties_tropical_wood_Bremaud_al.pdf

Éditeur(s) : HAL CCSD Fayard/Arthème
Résumé : La biomécanique des plantes est née d'une approche interdisciplinaire. Elle regroupe ainsi des biologistes, des forestiers ou des agronomes, et des mécaniciens (des matériaux et des structures et plus récemment des fluides). Elle s'intéresse à la façon dont les plantes se portent et croissent. En particulier comment les plantes terrestres croissent en hauteur " contre " la gravité et dans le vent ; mais aussi comment les plantes aquatiques et les algues se développent dans les courants.
Aux Origines des Plantes

hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935/document
https://hal.archives-ouvertes.fr/hal-00795935/file/BiomA_canique_plantes_Fournier_Moulia_Gril.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option B
Résumé :  
absent
ISSN: 0829-318X

hal-01032099
https://hal.archives-ouvertes.fr/hal-01032099
DOI : 10.1093/treephys/27.11.1505

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called G-layer, in the fibre wall. The structure of G-layer has been recently described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2 to 50 nm). This led us to revisit the concept of G-layer that was until now only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with typical thick G-layer while it is much less with thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without G-layer is as low as in normal wood. Not depending on the amount of pores, the pore sizes distribution are always centred around 6-12 nm. These results suggest that, among species producing fibres with G-layer, large structural differences of G-layer exist between species
ISSN: 0022-0957

hal-00387861
https://hal.archives-ouvertes.fr/hal-00387861
DOI : 10.1093/jxp/erp133

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Transverse drying shrinkage was measured at microscopic and mesoscopic levels in poplar wood characterised by an increasing growth strain (GS), from normal to tension wood. Results show that: (a) The drying shrinkage, measured as a relative thickness decrease, was significantly higher for G-layer (GL) than the other layers (OL), GL shrinkage was not significantly correlated with GS and OL shrinkage was negatively correlated with GS. (b) In gelatinous fibre (G-fibre), lumen size increased during drying and this increase was positively related with GS, but in normal wood fibre lumen size decreased during drying. These findings suggest that GL shrank outwards, so that its shrinkage feebly affected the total cell shrinkage and the mesoscopic shrinkage was controlled by the OL shrinkage which shrank inwards. (c) Measurements done on 7×7 mm² thin sections evidenced a negative correlation between transverse shrinkage and GS, significant in T direction but weak in R direction. These observations at both levels allow to discuss the contribution of GL to the mesoscopic shrinkage of tension wood.
ISSN: 0043-7719

hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930/document
https://hal.archives-ouvertes.fr/hal-00194930/file/WST_FANG2006.pdf
DOI : 10.1007/s00226-007-0148-3

Éditeur(s) : HAL CCSD Walter de Gruyter
Résumé : absent
Holzforschung

hal-01031939
https://hal.archives-ouvertes.fr/hal-01031939
DOI : 10.1515/HF.2005.057

Éditeur(s) : HAL CCSD
Résumé :  
The main aspects of wood mechanics are approached through the role played by wood as the building material of the tree. The main concepts used by nature: progressive setting up of tree weight and architecture, multifunctional role of wood and adaptability to hazard and long-term evolution, are clarified together with their consequence on the multilayered, anisotropic nature of wood. The technological choices of the plant world as the cellular structure, the use of composite with oriented fibres and hydro-carbonated polymers, as well as the systematic prestressing of every new layer, bear obvious consequences on the type of mechanical behaviour of wood. The local control of the level of prestressing through minor modifications of the cell-wall biosynthesis allows the tree to adapt to conditions of light exploration that will evolve according to time and risk occurrence. This analysis of wood genesis process permits in return to improve our understanding of the mechanical behaviour of the material in relation with the parameters of the microstructure.
Comptes Rendus de l'Académie des Sciences Série 2

hal-01032151
https://hal.archives-ouvertes.fr/hal-01032151
DOI : 10.1016/S1620-7742(01)01380-0

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Few studies have investigated the influence of environmental conditions on the within-treevariation in Eucalyptus wood traits. The genotype and environment effects and their interactionsinfluence the wood properties. Their evaluations are crucial to estimate the genotype values andto select with efficiency. Thus, the aim of this study was to better understand the effect ofground slope and wind speed on the spatial variation of basic density (ρ), stiffness (MOE) andmicrofibril angle (MFA) of Eucalyptus wood. Wood discs cut along the trunk were sampledfrom 150 six-year-old Eucalyptus grandis x E. urophylla hybrids growing in 3 contrastinggrowing conditions influenced by ground slope and wind regime. Near Infrared (NIR)calibrations previously developed for ρ, MOE and MFA were used to predict in our discs. 2-Dplots presenting the spatial variation of predicted wood traits were compared. The higher theground slope, the greater the magnitude of radial variation in ρ, principally in the medium zoneof the trunk. The spatial variation of wood stiffness seems to be sensitive to two environmentalconditions. The MFA radial decreases were more pronounced where the wind speed was higher.At the base and top of the trees, however, there was no significant effect of growing conditionson the radial variation of the wood properties considered here.
ISSN: 0931-1890

hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896/document
https://hal.archives-ouvertes.fr/hal-01451896/file/Art_Gril_al_Spatial_variation_wood_density_2016.pdf
DOI : 10.1007/s00468-015-1327-8

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either "artificially", or by natural extractives.
ISSN: 0043-7719

hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242/document
https://hal.archives-ouvertes.fr/hal-00804242/file/Anisotropy_wood_variational_properties_Bremaud_al_2011.pdf
DOI : 10.1007/s00226-010-0393-8

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Extractives can affect vibrational properties tanδ (damping coefficient) and E'/ρ (specific Young's modulus) but this is highly dependent on species, compounds, and cellular locations. This paper investigates such effects for African Padauk (Pterocarpus soyauxii Taub.), a tropical hardwood with high extractives content and a preferred material for xylophones. 5 groups of 26 heartwood specimens with large, yet comparable, ranges in vibrational properties were extracted in different solvents. Changes in vibrational properties were set against yields of extracts and evaluation of their cellular location. Methanol (ME) reached most of compounds (13%), located about half in lumen and half in cell-wall. Water solubility was extremely low. tanδ and E'/ρ were very strongly related (R2≥0.93), but native wood had abnormally low values of tanδ, while extraction shifted this relation towards higher tanδ values. ME extracted heartwood became in agreement with the average of many species, and close to sapwood. Extractions increased tanδ as much as 60%, irrespective of minute moisture changes or of initial properties. Apparent E'/ρ was barely changed (+2% to -4%) but, after correcting the mass contribution of extracts, was in fact slightly reduced (down to -10% for high E'/ρ), and increasingly so for specimens with low initial values of E'/ρ.
ISSN: 0043-7719

hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236/document
https://hal.archives-ouvertes.fr/hal-00804236/file/Effect_extractives_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0337-3

Éditeur(s) : HAL CCSD
Résumé :  
The gelatinous layer (G-layer) of tension wood fibres in hardwood contributes to the mechanical function of the living tree and has significant consequences on properties of solid wood. Its size, shape and structure observed by optical or electron microscopy exhibits characteristic anatomical features. However, we found that sectioning of non-embedded wood samples results in an uncontrolled swelling of the G-layer was monitored by serial sections, from an embedded wood sample, from its trimmed transverse face to that located several hundreds of micrometers deep. The results revealed that the initial cutting before embedding produced a border effect responsible for the swollen nature, which is similar to sections from non-embedded material. After a conventional embedding technique was applied, a section of at least 30 micrometres below the trimming surface is required to observe an un-swollen G-layer.
IAWA Journal

hal-01032054
https://hal.archives-ouvertes.fr/hal-01032054

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Active mechanisms of re-orientation are necessary to maintain the verticality of tree stems. They are achieved through the production of reaction wood, associated with circumferential variations of three factors related to cambial activity: maturation strain, longitudinal modulus of elasticity (MOE) and eccentric growth. These factors were measured on 17 mature trees from different botanical families and geographical locations. Various patterns of circumferential variation of these factors were identified. A biomechanical analysis based on beam theory was performed to quantify the individual impact of each factor. The main factor of re-orientation is the circumferential variation of maturation strains. However, this factor alone explains only 57% of the re-orientations. Other factors also have an effect through their interaction with maturation strains. Eccentric growth is generally associated with heterogeneity of maturation strains, and has an important complementary role, by increasing the width of wood with high maturation strain. Without this factor, the efficiency of re-orientations would be reduced by 31% for angiosperms and 26% for gymnosperms. In the case of angiosperms, MOE is often larger in tension wood than in normal wood. Without these variations, the efficiency of re-orientations would be reduced by 13%. In the case of gymnosperm trees, MOE of compression wood is lower than that of normal wood, so that re-orientation efficiency would be increased by 24% without this factor of variations.
ISSN: 0931-1890

hal-01031825
https://hal.archives-ouvertes.fr/hal-01031825
DOI : 10.1007/s00468-005-0407-6

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A
Résumé :  
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called the G-layer, in the fibre cell wall. The structure of the G-layer has recently been described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2-50 nm). This led us to revisit the concept of the G-layer that had been, until now, only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with a typical thick G-layer while it is much less with a thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without a G-layer is as low as in normal wood. Not depending on the amount of pores, the pore size distribution is always centred around 6-12 nm. These results suggest that, among species producing fibres with a G-layer, large structural differences of the G-layer exist between species.
Journal of Experimental Botany

hal-01032161
https://hal.archives-ouvertes.fr/hal-01032161
DOI : 10.1093/jxb/erp133

Éditeur(s) : HAL CCSD
Résumé : International audience
L'Angélique (Dicorynia guianensis Amsh.) représente environ 35% de laproduction de bois d'oeuvre en Guyane. Cependant, la stratégie de duraminisationdite ‘tardive’ chez cette essence entraîne une grande variabilité de l'épaisseurd'aubier (Fig. 1A) et par conséquent, influence la proportion exploitable de lagrume. La relation entre quantité de bois de coeur et diamètre à 1m30 (DBH) (e.g.Carrodus (1972), Wilkes (1991), Pinto et al. (2004), Wang et al. (2010)), ne permetpas une estimation suffisamment précise de la quantité de duramen et/ou d’aubier.A ce jour, très peu d’études mettent en lien la structure de la couronne et/ou lestatut social de l’individu avec la quantité de duramen (e.g. Pazdrowski et al.(2009), Nawrot et al. (2008)). Or, une grande diversité de structures des couronnesest observable au sein d’une même classe de diamètre (Fig. 1B).Ici, nous proposons une méthode visuelle et rapide de diagnostic architectural desarbres permettant d’améliorer l’estimation de la quantité de duramen dans letronc.
Les 2èmes Journées scientifiques du GDR 3544 « Sciences du bois »
Champs sur Marne, France

Droits : info:eu-repo/semantics/OpenAccess
hal-01215800
https://hal-sde.archives-ouvertes.fr/hal-01215800
https://hal-sde.archives-ouvertes.fr/hal-01215800/document
https://hal-sde.archives-ouvertes.fr/hal-01215800/file/Poster%20R.%20Lehnebach%20-%20GDR%20Bois%202013%20Structure%20couronne%20et%20variation%20de%20l%E2%80%99%C3%A9paisseur%20et%20surface%20aubier%20Ang%C3%A9lique.pdf

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
*Context Increased knowledge on diversity in wood properties would have implications both for fundamental research and for promoting a diversification of uses as material. *Aims The objective is to contribute to overcoming the critical lack of data on the diversity of wood dynamic mechanical/viscoelastic vibrational properties, by testing lesser-known species and categorizing sources of variability. *Methods Air-dry axial specific dynamic modulus of elasticity (E'/γ) and damping coefficient (tanδ) were measured on a wide sampling (1792 specimens) of 98 wood types from 79 species. An experimental device and protocol was designed for conducting systematic (i.e. rapid and reproducible) characterizations. *Results Diversity at the specimens' level corroborates the "standard" relationship between tanδ and E'/γ, which is discussed in terms of orientation of wood elements and of chemical composition. Diversity at the species level is expressed on the basis of results for normal heartwood, with specific gravity (γ) ranging from 0.2 to 1.3. Axial E'/γ ranges from 9 to 32 GPa and tanδ from 4×10-3 to 19×10-3. Properties distribution follows a continuum, but with group characteristics. The lowest values of tanδ are only found in certain tropical hardwoods. Results can also suggest alternative species for musical instruments making.
Annals of Forest Science

hal-00808242
https://hal.archives-ouvertes.fr/hal-00808242
https://hal.archives-ouvertes.fr/hal-00808242/document
DOI : 10.1007/s13595-011-0166-z

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0