Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
A comparative study of 9H-pyrido[3,4-b]indole (norharmane) and 1-methyl-9H-pyrido[3,4-b]indole (harmane) as inhibitors for C38 steel corrosion in 1 M HCl solution at 25 °C was carried out. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques were applied to study the metal corrosion behavior in the absence and presence of different concentrations of these inhibitors. The OCP as a function of time were also established. Cathodic and anodic polarization curves show that norharmane and harmane are a mixed-type inhibitors. Adsorption of indole derivatives on the C38 steel surface, in 1 M HCl solution, follows the Langmuir adsorption isotherm model. The ΔGads values were calculated and discussed. The potential of zero charge (PZC) of the C38 steel in inhibited solution was studied by the EIS method, and a mechanism for the adsorption process was proposed. Raman spectroscopy confirmed that indole molecules strongly adsorbed onto the steel surface. The electronic properties of indole derivates, obtained using the AM1 semi-empirical quantum chemical approach, were correlated with their experimental efficiencies using the linear resistance model (LR).
ISSN: 0018-3830

hal-01093227
https://hal-agroparistech.archives-ouvertes.fr/hal-01093227
DOI : 10.1515/HF.2010.034

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Displacement-length data from dilatant fractures (joints, veins, igneous dikes) and several varieties of deformation bands were analyzed statistically to investigate the applicability of mechanical models proposed for their formation. All 17 datasets are generally consistent with equilibrium or long-term power-law slopes on the displacement-length diagram of either 1.0 or 0.5. Similar to many faults, disaggregation deformation bands are consistent with a power-law scaling relation having a slope of approximately c = 1, implying a linear dependence of maximum displacement and discontinuity length (Dmax = γL). In contrast, dilatant fractures, cataclastic deformation bands, and shear-enhanced compaction bands are consistent with a power-law scaling relation with a slope of approximately c = 0.5, implying a dependence of maximum displacement on the square root of length (Dmax = αL1/2). The scaling relations represent an average, or long-term equilibrium outcome of deformation for conditions such as length-scale, time-scale, temperature, chemistry, and an effectively homogeneous far-field stress field, allowing for variations such as rapid and/or localized behaviors. The displacement-length scaling of these geologic structures follows systematic relationships that provide information on host-rock properties and the physics of fracture and deformation-band propagation.
ISSN: 0191-8141

hal-00818130
https://hal.archives-ouvertes.fr/hal-00818130
DOI : 10.1016/j.jsg.2012.12.005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wallace (1951) and Bott (1959) were the first to introduce the idea that the slip on each fault surface has the same direction and sense as the maximum shear stress resolved on that surface. However, this simplified hypothesis is questionable since fault mechanical interactions may induce slip reorientations. Earlier numerical geomechanical models confirmed that the slickenlines (slip vectors) are not necessarily parallel to the maximum resolved shear stress but are consistent with local stress perturbations. This leads us to ask as to what extent the Wallace and Bott simplifications are reliable as a basis hypothesis for stress inversion from fault slip data. Here, a geomechanical multi-parametric study using a 3D boundary element method, covering (i) fault geometries such as intersected faults or corrugated fault surfaces, (ii) the full range of Andersonian state of stress, (iii) fault friction, (iv) fault fluid pressure, (v) half space effect and (vi), rock properties, is performed in order to understand the effect of each parameter on the misfit angle between geomechanical slip vectors and the resolved shear stresses. It is shown that significant misfit angles can be found under specific configurations invalidating the Wallace and Bott assumptions, even though fault friction tends to minimize the misfit. We therefore conclude that in such cases, stress inversions based on fault slip data should be interpreted with care.
ISSN: 0040-1951

hal-01218418
https://hal.archives-ouvertes.fr/hal-01218418
DOI : 10.1016/j.tecto.2015.06.030

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The analysis of three cataclastic band sets from Provence (France) reveals that the band density, their conjugate angles, their ratio of shear displacement to compaction, and the amount of cataclasis within the bands differ and can be expressed as functions of tectonic setting and petrophysical properties. We identify (1) a dense and closely spaced network of shear-enhanced (reverse) compaction bands; (2) a regularly spaced less dense network of reverse compactional shear bands; and (3) a localized network of normal shear bands. The field data show that strain localization is favored in an extensional regime and is characterized by shear bands with a large shear to compaction ratio and a small conjugate band angle. In contrast, distributed strain is favored in a contractional regime and is characterized by compactional bands with a low ratio of shear to compaction and a large conjugate band angle. To explain the mechanical origin of this strain localization, we quantify the yield strength and the stress evolution in extensional and contractional regimes in a frictional porous granular material. We propose a model of strain localization in porous sands as a function of tectonic stresses, burial depth, material properties, strain hardening and fluid pressure. Our model suggests that stress reduction, inherent to extensional regime, favors strain localization as shear bands, whereas stress increase during contraction favors development of compactional bands.
ISSN: 0191-8141

hal-00856921
https://hal.archives-ouvertes.fr/hal-00856921
DOI : 10.1016/j.jsg.2012.11.011

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The early apoptotic events induced by environmental pollutants with carcinogenic properties are poorly understood. Here, we focus on the early cytotoxic effects of benzo[a]pyrene (B[a]P). In F258 rat hepatic epithelial cells, B[a]P induces intrinsic apoptosis via a mitochondrial dysfunction characterized by the release of hexokinase II (HKII) from the mitochondria. Cancer cells often have an anomalous cell energy metabolism; since HKII dysfunction regulates B[a]P-induced apoptosis in F258 cells, but may also alter cell energy metabolism, HKII release from the mitochondria may represent an important B[a]P-related carcinogenic issue. Thus in the present study, we aimed at deciphering the mechanisms underlying HKII dysfunction upon B[a]P exposure. We show that while glycogen synthase kinase 3 beta (GSK3β) regulated the expression of HKII at the transcriptional level, glycogen synthase kinase 3 alpha (GSK3α) was involved in B[a]P-induced apoptosis via a decrease in c-Myc expression. The reduced level of c-Myc caused the relocation of HKII from the mitochondria to the cytosol, thereby being involved in the formation of reactive oxygen species and apoptosis. In conclusion, we show that the couple GSK3α/c-Myc plays a key role in B[a]P-induced early apoptotic cell signaling via HKII dysfunction.
ISSN: 0887-2333

hal-00682104
https://hal.archives-ouvertes.fr/hal-00682104
https://hal.archives-ouvertes.fr/hal-00682104/document
https://hal.archives-ouvertes.fr/hal-00682104/file/1-s2.0-S0887233311003018-main%20Dendel%C3%A9_%7B75929874-2DF9-47C3-92F6-92AF398668E5%7D.pdf
DOI : 10.1016/j.tiv.2011.11.001

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A
Résumé :  
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called the G-layer, in the fibre cell wall. The structure of the G-layer has recently been described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2-50 nm). This led us to revisit the concept of the G-layer that had been, until now, only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with a typical thick G-layer while it is much less with a thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without a G-layer is as low as in normal wood. Not depending on the amount of pores, the pore size distribution is always centred around 6-12 nm. These results suggest that, among species producing fibres with a G-layer, large structural differences of the G-layer exist between species.
Journal of Experimental Botany

hal-01032161
https://hal.archives-ouvertes.fr/hal-01032161
DOI : 10.1093/jxb/erp133

Éditeur(s) : HAL CCSD
Résumé : International audience
The hierarchical architecture of biopolymers induces remarkable behaviour. Wood mechanical properties mainly originate from the organization of wood tissue and interactions of cellwall components. The respective contribution on components inside those networks occurs at nanometric scale and still challenging to investigate in-situ. X-ray scattering techniques are now used as a routine technique to investigate internal organization of material components. For that purpose large-scale synchrotron facilities like ESRF offer leading X-ray sources capabilities (large energy range, high brilliance, high intensity, dedicated setups). ESRF's ID13 beamline serves high spacial resolution scanning setups to expertise in elastic scattering of monochromatic X-rays. Since analytical description of the scattering signal of cellulose have been well describe wood material benefit wide range of exposure conditions and sample environment. During this conference, we will present our achievements based on transverse sections of poplar specimens exposed to micrometric beam (1.2 μm side, 12.6 keV energy) to reveal crystalline cellulose distribution within wood tissue and to nanometric beam (100 nm side, 12 6 keV energy) to map the evolution of cellulose orientation within double cell wall over combined Wide-Angle (WAXS) and Small-Angle (SAXS) X-ray Scattering configuration. Within those setups hygrometric sample environment and stretching solicitations will be approached based on-going developments.
COST FP0802 Workshop 'Micro Characterisation of Wood Material'
Edimbourg, United Kingdom

hal-01113298
https://hal.archives-ouvertes.fr/hal-01113298

Éditeur(s) : HAL CCSD American Society for Microbiology
Résumé : International audience
Coronaviruses (CoVs) have shown neuroinvasive properties in human and animal secondary to replication in peripheral organ but the mechanism of neuroinvasion is unknown. The major aim of our work was to evaluate the ability of CoVs to enter the central nervous system (CNS) through the blood brain barrier (BBB). Using the high hepatotropic mouse hepatitis virus (MHV) type 3, its attenuated variant 51.6-MHV3, showing low tropism for endothelial cells, and the low hepatotropic MHV-A59 strains from murine coronavirus group, we investigated the viral-induced dysfunctions of BBB in vivo and in brain microvascular endothelial cells (BMECs) in vitro. We report here a MHV strain-specific ability to cross the BBB during acute infection according to their virulence for liver. Brain invasion was only observed in MHV3-infected mice and correlated with enhanced BBB permeability associated with decreased expression of ZO-1, VE-cadherin and occludin but not claudin-5 in the brain or in cultured BMECs. BBB breakdown in MHV3 infection was not related to production of barrier-dysregulating inflammatory cytokines or chemokines by infected BMECs but rather to a downregulation of barrier protective IFN-β production. Our findings highlight the importance of IFN-β production by infected BMECs in preserving BBB function and preventing access of blood-borne infectious viruses to the brain. IMPORTANCE: Coronaviruses (CoVs) infect several mammals including humans and are associated with respiratory, gastrointestinal and/or neurological diseases. Some evidences suggest that human respiratory CoVs may show neuroinvasive properties. Indeed, the SARS-CoV, causing severe acute respiratory syndrome, and the CoVs OC43 and 229E were found in the brains of SARS and multiple sclerosis patients respectively. These finding suggest that hematogenous spread CoVs may gain access to CNS at the BBB level. Herein we report for the first time that CoVs exhibit ability to cross the BBB according to strain virulence. BBB invasion by CoVs correlates with viral-induced disruption of tight junctions on BMECs, leading to BBB dysfunction and enhanced permeability. We provide evidence that production of IFN-β by BMECs during CoV infection may prevent BBB breakdown and brain viral invasion
ISSN: 0022-538X

hal-01187308
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01187308
DOI : 10.1128/JVI.01501-15
PUBMED : 26202229

Éditeur(s) : HAL CCSD
Résumé : International audience
The main biological function of reaction wood is to act as “muscle” for trees, enabling them to control their posture and right stems when they are permanently disturbed from their set-point inclination by gravity or winds. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called “maturation strains”. Moreover, this function is basically performed through the asymmetric formation of wood (in quantity or quality) around the tree circumference. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity, as an asymmetric force associated to maturation strains creates a bending moment (i.e. one side of the stem “pulls” the other one). We will discuss the traits (cross sectional size and shape, wood features as G fibers or microfibril angle, eccentric growth even in usual or extreme cases as buttresses, total biomass growth and height of center of mass, stem lean and set-point angle) involved to understand how the posture control works. We will give simple formulas to estimate a “muscle efficiency” from biomechanical modeling. We will give practical methods to estimate all the involved traits, especially maturation strains from direct and indirect measurements, in peripheral functional wood or by retrospective dendrochronological analysis. Then, we will illustrate how tree stem tropisms and especially gravitropism, widely studied by physiologists, are key processes in natural ecosystems, through practical examples from tropical rainforest tree communities and regeneration of European mixed beech forests. Using the previous definition of postural control efficiency, we will show that the cross section size is rapidly a limiting factor, opposing the extreme strategies of flexible small stems, which bend easily but also right themselves quickly, to stiff big stems. Lastly, as wood in living trees ensures general storage, defence, vascular and skeletal functions, we will ask general questions about synergies and trade-offs between posture control and other functions.
Botany 2014 : new frontiers in botany
Boise, United States

hal-01627031
https://hal.archives-ouvertes.fr/hal-01627031

Éditeur(s) : HAL CCSD
Résumé : International audience
While the impact of network properties on information spread- ing is now widely studied, in uence of network dynamics is very little known. In this paper, we study how evolution mechanisms tradition- ally observed within social networks can a ect information di usion. We present an approach that merges two models: model of informa- tion di usion through social networks and model of network evolution. Since epidemics provide a reference in application domains of information spreading, we measure the impact of basic network structure changes on epidemic peak value and timing. Then we investigate observed trends in terms of changes appearing in the network structure. Our results provide promising results on how and why network dynamics is a strong param- eter to integrate in requirements for information spreading modelling.
World Summit on the Knowledge Society
Mykonos, Greece

hal-00768405
https://hal.archives-ouvertes.fr/hal-00768405

Éditeur(s) : HAL CCSD Montpellier : CIRAD
Résumé :  
Influence de la température sur le comportement mécanique du bois vert: application à l'étuvage d'essences guyanaises en vue du déroulage. Des essais mécaniques dans les directions orthogonales à la fibre et des essais de déroulage ont été menés en parallèle sur 10 essences guyanaises, de densité variant de 0,27 à 1,18, et à 12 températures croissant de 25 à 80 °C. L'influence de la densité et de la température sont très fortes et souvent couplées. Les essais mécaniques peuvent être utilisés pour expliquer les variations des efforts de coupe. Les ratios entre descripteurs mécaniques apparaissent comme des prédicteurs intéressants de l'aptitude au déroulage des bois homogènes.
ISSN: 0006-579X

hal-01032179
https://hal.archives-ouvertes.fr/hal-01032179

Éditeur(s) : HAL CCSD
Résumé : Composite materials incorporating vegetable fibres have known an increasingly interest during the past few decades. These environmental friendly materials are low-cost and offer advantages such as reduction of electrical consumption by air conditioning. Moreover, the use of vegetable fibres in replacement of synthetic fibre is interesting in developing countries where the availability of tropical plants and agricultural waste is important. This paper presents an initial investigation on the use of a construction material, composed of cement and pre-treated (heat or alkaline treatments) sugar cane bagasse fibres. The purpose of this study is to analyse the effect of fibre content and treatment on thermal conductivity, specific heat, flexural strength and density. The addition of retified fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline fibres. From mechanical point of view, composites made with alkaline fibres have a better flexural strength than others.
12th International Inorganic-bonded Fiber Composites Conference
Aalborg, Denmark

hal-00807543
https://hal.univ-antilles.fr/hal-00807543

Éditeur(s) : HAL CCSD Springer-Verlag
Résumé : International audience
High-resolution borehole strainmeters are usually installed in tectonically active regions in order to detect slow-slip events, and to estimate slow transients related to earthquake swarms. However, they are also sensitive to other numerous influences, internal or external. Furthermore, the quality of their coupling to the rock through cementation, and the mechanical properties of the rock mass around them, have a critical influence on their records. Many of the existing strainmeters present such problems, and the correction for these effects often remains a challenge. In this paper, we present the analysis of the records of a high-resolution borehole dilatometer (Sacks–Evertson), located in the seismically active rift of Corinth (Greece) (station TRZ in the Trizonia island). We show that the instrument suffers from an only partial-solid coupling, and that the nearby sea tides have a direct (through elastic response) and indirect (through pore-pressure diffusion) effect on the dilatation signal, which adds up to the solid tidal strain source. We propose a methodology that allows, in a first step, to better separate the internal (solid tide) from the external (air pressure, sea level) influences, by calculating a frequency-dependent transfer function outside the range of the tidal periods. We then extrapolate this function, in particular at the tidal periods. In a second step, the resulting variation with frequency of the coupling coefficients with sea level led us to estimate the proportion of instrument not solidly cemented to rock (thus in contact with water pore pressure), which is about 90 % of the total height. Despite the small proportion of solid coupling, the sensor resolution remains very good up to a few tens of hours of a time period, thanks to the confining effects of the rocks on the local pore pressure. These results allow us to correct for the external effects, and reduce the associated variance by 80–90 % (in the period range of minutes to days). The empirical correction of the sea level effect could be explained using a simple Boussinesq’s approximation and 1D pore-pressure diffusion model, which contributed to better constraint of some of the poro-elastic parameters in the vicinity of the instrument. After correction, the solid tidal signal at the 24-h period is almost anti-correlated with those of the theoretical solid tide. This surprising result is consistent with a similar anti-correlation observed for the longest period surface waves (200 s) comparing the TRZ dilatometer signals to the strain measured by a nearby borehole strainmeter (MOK, 15 km). This could be related to the presence of a shallow fault close to the instrument, which would creep in response to seismic wave-related stress.
ISSN: 0033-4533

hal-01122853
https://hal.archives-ouvertes.fr/hal-01122853
DOI : 10.1007/s00024-013-0742-2

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
Brain-derived neurotrophic factor (BDNF), a member of the neurotrophin family, has emerged as an active mediator in many essential functions in the central nervous system of mammals. BDNF plays significant roles in neurogenesis, neuronal maturation and/or synaptic plasticity and is involved in cognitive functions such as learning and memory. Despite the vast literature present in mammals, studies devoted to BDNF in the brain of other animal models are scarse. Zebrafish is a teleost fish widely known for developmental genetic studies and is emerging as model for translational neuroscience research. In addition, its brain shows many sites of adult neurogenesis allowing higher regenerative properties after traumatic injuries. To add further knowledge on neurotrophic factors in vertebrate brain models, we decided to determine the distribution of bdnf mRNAs in the larval and adult zebrafish brain and to characterize the phenotype of cells expressing bdnf mRNAs by means of double staining studies. Our results showed that bdnf mRNAs were widely expressed in the brain of 7 days old larvae and throughout the whole brain of mature female and male zebrafish. In adults, bdnf mRNAs were mainly observed in the dorsal telencephalon, preoptic area, dorsal thalamus, posterior tuberculum, hypothalamus, synencephalon, optic tectum and medulla oblongata. By combining immunohistochemistry with in situ hybridization, we showed that bdnf mRNAs were never expressed by radial glial cells or proliferating cells. By contrast, bdnf transcripts were expressed in cells with neuronal phenotype in all brain regions investigated. Our results provide the first demonstration that the brain of zebrafish expresses bdnf mRNAs in neurons and open new fields of research on the role of the BDNF factor in brain mechanisms in normal and brain repairs situations.
ISSN: 1932-6203

hal-01359562
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01359562
DOI : 10.1371/journal.pone.0158057
PUBMED : 27336917

Résumé : La tribologie est définie comme la science qui étudie les phénomènes de frottement, d’usure et de lubrification. Elle intervient à chaque fois que deux surfaces sont en mouvement relatif l’une par rapport à l’autre. On la rencontre donc principalement dans les moteurs, les instruments de coupe, les assemblages mécaniques etc. Le frottement et l’usure sont les causes principales des pertes de performances et de durabilité des systèmes. L’usure coute 3 % du PIB en France et on estime que 10 % à 30 % de l’énergie produite dans le monde est consommée par frottement, c’est dire l’importance que porte le monde industriel à cette science.C'est la lubrification qui a pour rôle de minimiser le frottement et de protéger les surfaces de l'usure. Il existe différents régimes de lubrification, cependant les travaux effectués au cours de cette thèse de doctorat s’intéressent exclusivement au régime de lubrification limite. Dans ce régime de lubrification, l’épaisseur du film de lubrifiant est du même ordre de grandeur que la hauteur des aspérités des surfaces en contact et le frottement et l'usure des surfaces peuvent être très sévères. La stratégie mise en place pour lutter contre ces phénomènes consiste à ajouter des additifs à l'huile lubrifiante, qui formeront au cours du frottement un film protecteur (le tribofilm). Il apparait donc primordial de bien caractériser ces tribofilms afin de mieux comprendre les mécanismes de réduction de frottement et de l’usure, qui restent encore à ce jour mal connus.Les nanotechnologies permettent aujourd'hui d'apporter un nouvel éclairage sur cette problématique et nous les avons mises à profit pour étudier le comportement mécanique des tribofilms à l’échelle nanométrique.L’objectif de ce travail est de comprendre les processus de réduction de frottement observés à l’échelle macroscopique lorsque des particules de composés lamellaires sont associées à un liquide de faible viscosité. Les tribofilms étudiés sont formés à partir de trois composés lamellaires différents, le graphite, le thiophosphate de nickel NiPS3 et le bisulfure de molybdène MoS2. Pour ces trois composés, deux types de tribofilms ont été étudiés : ceux formés à partir des particules seules (les tribofilms secs) et ceux formés en présence de liquide (les tribofilms éther).L’analyse des propriétés tribologiques mesurées à macro et nano échelle, nous ont permis de mieux comprendre la contribution des effets individuels et collectifs sur les mécanismes réducteurs de frottement. Ces expériences ont permis de mettre en évidence que la réduction du coefficient de frottement observée à macro-échelle n'est pas due à la nanostructuration des tribofilms ni à une baisse des interactions entre les feuillets mais plutôt à un effet collectif des particules et du liquide.
Tribology is the science of friction phenomena, wear and lubrication. It takes part every time two surfaces are in relative motion. It performs meanly in engine and mechanical systems. Friction and wear are the mean reasons of loose of performance and durability of mechanical systems. Wear costs 3% of the GDP in France and about 10% to 30% of the produced energy in the world is consumed by friction.The aim of lubrication is to reduce friction and protect the surface against wear. There are four different types of lubrication regimes but this study is focused on the boundary regime. In this regime, lubricant thickness is of the same order of the magnitude of the sliding surfaces roughness, leading to a high-level of friction and wear. Additives are added to the lubricating base oil, in order to build a protecting tribofilm. Characterization of the tribofilms appears essential to better understand the friction and wear reduction mechanisms.Nanotechnology allows to bring a new insight on this issue through the study of the mechanical behavior of the tribofilms at nanoscale.The aim of this work is to better understand the process of the friction reduction observed at macroscale when lamellar particles are associated to a low viscosity liquid. The tribofilms are formed from three different lamellar compounds, graphite, nickel thiophosphate NiPS3 and molybdenum disulfide MoS2. Two different kinds of tribofilms are studied: those formed with the solids particles only (dry tribofilms) and those formed in presence of liquid (wet tribofilms).The analyses of the tribological properties measured at nanoscale allow us to better understand the contribution of the individual and collective effects on friction reduction mechanims. We show that the reduction of the friction coefficient observed at macroscale is not related to the surface nanostructuration of the tribofilms neither to the decrease of the interaction energy between the sliding surfaces, but rather to collective effects of the liquid and the particles in the contact.

http://www.theses.fr/2014AGUY0706/document

Résumé : L'objectif de cette thèse est de s'intéresser à la chimie des substances naturelles (extraction et caractérisation des molécules issues des forêts de Guyane) et d'étudier des extraits ou familles de molécules naturelles ayant des propriétés inhibitrices de la corrosion du zinc. Dans la première partie du document, un screening de plantes a été effectué. Celles dont les extraits ont présenté les propriétés inhibitrices les plus intéressantes - la Mansoa alliaceae et la Bagassa guianensis -ont été sélectionnées parmi les Il plantes étudiées. Dans la seconde partie du document, différentes techniques électrochimiques ont été utilisées- la spectroscopie d'impédance électrochimique (SEI) et la polarisationlinéaire (PL)- afin de calculer les taux d'inhibition et de remonter aux mécanismes réactionnels caractérisant l'inhibition. Ainsi, le rôle des paramètres tels que le mode d'extraction et le milieu corrosif (ASTM et NaCI3%) sur le taux d'inhibition ont été étudiés. Ces travaux ont débouché sur de nombreux résultats expérimentaux nouveaux et notamment un modèle dynamique prenant en compte l'efficacité de l'inhibiteur en fonction de sa concentration dans le milieu
The objective of this thesis is to focus on the chemistry of na tura! substances (extraction and characterization of molecules from forests of French Guiana) and to study extracts or families ofnatural molecules with inhibiting properties of zinc corrosion. In the first part of the document, a screening of plants was made. Those whose extracts have shown the most interesting potential inhibitors - the Mansoa alliaceae and Bagassa guianensis - were selected among the Il plants studied. In the second part of the paper, different electrochemical techniques were used - the electrochemical impedance spectroscopy (EIS) and linear polarization (LP) - to calculate the inhibition rate and to understand the reaction mechanisms characterizing the inhibition. Thus, the role of parameters such as the method of extraction and the corrosive medium (ASTM and NaCI3%) on the inhibition rate were studied. This work bas led to many new experimental results including a dynamic mode! taking into account the effectiveness of the inhibitor according to its concentration in the medium

http://www.theses.fr/2014AGUY0745/document

Résumé : Le fluide chaud produit par les forages de la centrale géothermique de Bouillante (Guadeloupe) est enrichi en espèces dissoutes telles que la silice qui peuvent précipiter sous forme de dépôts solides lors de son refroidissement et gêner fortement la production électrique. L’un des principaux objectifs de ce travail de thèse a donc été d’améliorer l’état des connaissances sur les conditions physiques, chimiques et cinétiques de la précipitation de la silice amorphe à Bouillante. Après une étude des caractéristiques physico-chimiques des fluides et des dépôts associés au champ de Bouillante, des expériences sur la cinétique de précipitation de la silice, sur site, pour une large gamme de température (25 - 90°C) et de pH (4 - 12) ont été menées et analysées en détail.Pour l’ensemble de ces expériences, seule la polymérisation (réversible) de la silice dissoute, sous forme de suspensions colloïdales très stables en solution, a été observée. La modélisation des données expérimentales de cinétique montre que la vitesse de polymérisation de la silice suit une loi d’ordre 2 vis-à-vis de la silice dissoute jusqu’à l’équilibre en accord avec une dimérisation de la silice. Par contre, durant l’étape initiale de la réaction, une loi d’ordre 4 semble mieux adaptée, suggérant des réactions de polymérisation plus complexes avec formation de tétramères. La température a un effet limité sur la cinétique de polymérisation de la silice comparé à l’effet du pH qui est beaucoup plus important. L’énergie d’activation de la réaction globale est de 41 - 54 kJ pour des pH compris entre 5 et 8.La caractérisation de la silice précipitée a mis en évidence des différences notables entre la structure poreuse de la silice solide prélevée sur les installations de surface et celle de la silice colloïdale obtenue par polymérisation lors des expériences de cinétique, ce qui semble indiquer que des mécanismes différents interviennent dans ces deux contextes de précipitation de la silice dissoute.Le deuxième objectif de cette thèse était d’évaluer la possibilité de valoriser la silice extraite de l’eau géothermale de Bouillante dans un procédé de traitement des eaux naturelles par adsorption. Pour cela, les propriétés d’adsorption de la silice géothermale brute et fonctionnalisée par le poly(ethylèneimine) (ou PEI) ont été étudiées pour deux polluants : un colorant, le bleu de méthylène et un métal lourd, le plomb. Les résultats obtenus montrent que la silice brute possède une grande capacité d’adsorption vis-à-vis du bleu de méthylène. En outre, la fonctionnalisation de la silice par le PEI permet d’améliorer sa capacité d’adsorption vis-à-vis du plomb en solution, en accord avec un modèle cinétique du pseudo-second ordre suggérant une chimisorption. Le modèle d’isotherme de Redlich-Peterson est également en très bon accord avec les données expérimentales.
The hot geothermal fluid produced by the geothermal power plant of Bouillante (Guadeloupe) contains various dissolved components such as silica that can precipitate as solid deposits during their cooling and cause serious problems on the electricity generation. One of the aim of this study is to improve the understanding on the physical, chemical and kinetics conditions of the amorphous silica precipitation in the Bouillante geothermal field. After a study on the physical and chemical characteristics of the Bouillante fluids and deposits which can form during their exploitation, experiments on the kinetics of silica precipitation, on site, under a large range of temperature (25 – 90°C) and pH (4 – 12) have been carried out and analyzed in detail.During on site kinetics experimentations only dissolved silica polymerization (reversible) as colloidal gel, very stable in solution, was observed. Modeling of the experimental data showed that the kinetics polymerization is characterized by a 2-order kinetic law relative to dissolved silica until the equilibrium that is consistent with silica dimerization. On the other side, the initial stage of the reaction is better characterized by a 4-order kinetic law that suggested more complex polymerization reactions with tetramers formation.Temperature has a little effect on the polymerization kinetics compared with the pH which has an effect more important. The activation energy of silica precipitation calculated between 25 and 90°C, is about 41 - 54 kJ for pH ranging to 5 - 8.The characterization of the silica precipitate reveals significant differences in the porous structure of the silica collected on the surface installations and the one obtained from kinetic experiments that suggests different precipitation mechanisms. The second objective of this thesis was to evaluate the possibility to promote geothermal silica for the treatment of natural waters containing contaminants by adsorption. Adsorption properties of the untreated and functionalized by poly(ethylèneimine) (ou PEI) geothermal silica have been investigated for two pollutants: a colorant, the methylene blue and a heavy metal, the lead.Results showed that untreated silica has a great adsorption capacity concerning the methylene blue. Besides, silica functionalization by the PEI allows improving the adsorption capacity for lead in solution. The adsorption kinetics curves followed a pseudo-second order model consistent with a chimisorption. The isotherm model of Redlich-Peterson fitted well the experimental data.

http://www.theses.fr/2014AGUY0698/document

Éditeur(s) : HAL CCSD American Geophysical Union (AGU) American Geophysical Union
Résumé : International audience
The brittle to ductile transition may strongly influence hydraulic properties of rocks at the depth and temperature ranges that hydrothermal fluids circulate. To examine this transition in the context of the oceanic crust, we conducted a series of deformation experiments on a natural basalt sample at in situ oceanic crust conditions. Dilatancy was measured during deformation. The method consisted in monitoring the volume of pore fluid that flows into or out of the sample at constant pore pressure. Mechanical and microstructural observations at experimental constant strain rate of 10−5 s−1 indicated that the basalt was brittle and dilatant up to 800°C. At higher temperature, the deformation mode became macroscopically ductile and samples compacted. These observations have important implications on heat transfer and fluid migration in oceanic crust.
ISSN: 0094-8276

hal-01172352
https://hal.archives-ouvertes.fr/hal-01172352
DOI : 10.1002/2015GL063437

Résumé : L’ingénierie agroécologique vise à produire des savoirs actionnables, pour concevoir des systèmes de cultures économiquement et écologiquement performants, par la valorisation de régulations naturelles. Notre problématique est centrée sur la santé des cultures, et plus particulièrement sur la bactérie phytopathogène Ralstonia solanacearum, agent du flétrissement bactérien alors qu’une souche extrêmement agressive menace la production de tomates en plein champ en Martinique. La nécessité d’explorer et de développer des alternatives aux méthodes conventionnelles de protection des plantes (variétés résistantes, pesticides), actuellement inefficaces, invite à la mise en œuvre d’une démarche de conception innovante. Nos travaux montrent que la mobilisation d’une barrière rhizosphérique est une stratégie de régulation biologique alternative. Différents processus y contribuent, telle que la mycorhization, symbiose entre racines et champignons mycorhiziens à arbuscules, présents dans la plupart des sols. Nous montrons que la mobilisation de réseaux de mycorhizes indigènes à partir d’un sol agricole permet une mycorhization précoce de la tomate. De plus, l’association de plantes aux propriétés mycorhizotrophes et assainissantes en conditions contrôlées montre des effets bioprotecteurs partiels et ouvre de nouvelles perspectives de combinaisons entre processus. Ces combinaisons sont mobilisables par des leviers d’actions multi-scalaires. Nous avons produit une grille d’analyse générique de ces leviers d’action pour la conception, par des trajectoires d’innovation multidirectionnelles, de « systèmes de culture bioprotégés ». Dans le contexte agricole martiniquais, une démarche d’apprentissage permet en effet l’émergence d’une dynamique de co-conception de systèmes de cultures recourant aux plantes mycorhizotrophes. Nos travaux proposent des outils pour une exploration collective de nouvelles stratégies de gestion durable de la santé des cultures.
Agroecological engineering aims to produce actionable knowledge to design economically and environmentally efficient cropping systems, based on the exploitation of natural regulation mechanisms. Our issue is centered on crop health, especially on the plant pathogenic bacterium Ralstonia solanacearum (bacterial wilt agent), of which an extremely aggressive strain threatens field tomato production in Martinique. The need to explore and develop alternatives to conventional methods of plant protection (resistant varieties, pesticides), ineffective in our case, calls for the implementation of an innovative design approach. Our work shows that the protection of the roots via the formation of a self-sustaining rhizospheric barrier may be an alternative biological control strategy. Different processes contribute, such as mycorrhizal symbiosis between roots and arbuscular mycorrhizal fungi, which are present in most soils. We show that the mobilization of indigenous mycorrhizal networks from an agricultural soil allows early mycorrhization of tomatoes. In addition, the association of plants with mycorrhizal and sanitizing properties in controlled conditions showed partial bioprotective effects and opens up new prospects for combinations between processes. These combinations may be exploited in various ways. We produced a generic analysis grid of key levers to design "healthy cropping systems " through multi-directional innovation trajectories. In Martinique's agricultural context, a learning process allows the emergence of a dynamic co-design of cropping systems using mycorrhizal plants. Our work thus provides tools for collective exploration of new sustainable management strategies for crop health.

http://www.theses.fr/2015AGUY0828/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Numerical programs for simulating flow and reactive transport in porous media are essential tools for predicting reservoir properties changes triggered by CO2 underground injection. At reservoir scale, meshed models in which equations are solved assuming that constant macroscopic properties can be defined in each cells, are widely used. However, the parameterization of the dissolution-precipitation problem and of the feedback effects of these processes on the flow field is still challenging. The problem arises from the mismatch between the scales at which averaged parameters are defined in the meshed model and the scale at which chemical reactions occur and modify the pore network geometry. In this paper we investigate the links between the dissolution mechanisms that control the porosity changes and the related changes of the reactive surface area and of the permeability. First, the reactive surface area is computed from X-ray microtomography data obtained before and after a set of dissolution experiments of pure calcite rock samples using distinctly different brine-CO2 mixtures characterizing homogeneous to heterogeneous dissolution regimes. The results are used to validate the power law empirical model relating the reactive surface area to porosity proposed by Luquot and Gauze (2009). Second, we investigate the spatial distribution of the effective hydraulic radius and of the tortuosity, two structural parameters that control permeability, in order to explain the different porosity-permeability relationships observed for heterogeneous and homogeneous dissolution regimes. It is shown that the increase of permeability is due to the decrease of the tortuosity for homogeneous dissolution, whereas it is due to the combination of tortuosity decrease and hydraulic radius increase for heterogeneous dissolution. For the intermediate dissolution regime, identified to be the optimal regime for increasing permeability with small changes in porosity, the increase of permeability results from a large increase in the mean effective hydraulic radius of the sample.
ISSN: 0169-7722

hal-00617671
https://hal.archives-ouvertes.fr/hal-00617671
DOI : 10.1016/j.jconhyd.2010.07.004