Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Porous thin films considered for applications like separation, sensing and microelectronic have to sustain mechanical stresses during their integration process or in working conditions. Thanks to recent progress in processing methods, it is now possible to precisely control the porosity and combine ordered mesopores with randomly-distributed macropores to achieve hierarchically porous materials. The mechanical properties of thin films containing different types of porosity (ordered meso, random macro and hierarchical) have been investigated by means of nanoindentation. In particular a method recently proposed by Li and Vlassak (H. Li, J.J. Vlassak, Journal of Materials Research 24 (2009) 1114-1126) is applied to account for the substrate effect. Residual indent impressions were imaged by Atomic Force Microscopy (AFM) to provide some insights in the mechanical behavior of the films. In addition, experimental indentation moduli are compared to theoretical predictions obtained via Finite Element (FE) analysis. The different porous structures have been modeled by FE to obtain the effective elastic properties from which the indentation modulus can be inferred. Finally, the experimental-model differences are discussed. © 2010 Elsevier Inc. All rights reserved.
ISSN: 1387-1811

hal-01683194
https://hal.univ-antilles.fr/hal-01683194
DOI : 10.1016/j.micromeso.2010.09.004

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
To quantify the seismic properties of lower crustal rocks and to better constrain the origin of the lower crustal seismic reflectivity, we determined the complete 3-D seismic properties of a lower crustal section. Eight representative samples of the main lithologic and structural units outcropping in the Val Sesia (Ivrea zone) were studied in detail. The seismic velocities were calculated using the single crystal stiffness coefficients and the lattice preferred orientation (LPO) of each mineral in all samples. The 21 stiffness coefficients characterizing the elastic behaviour of each rock are determined. Mafic and ultramafic rocks such as pyroxenite and pyroxene-bearing gabbros display complex shear wave properties. These rocks are weakly birefringent (maximum 0.1 kms-1) and it is difficult to find consistent relationships between the seismic properties and the rock structure. On the other hand, seismic properties of deformed felsic rocks are essentially controlled by mica. They display strong S-wave birefringence (0.3 km s-1) and relatively high Vp anisotropy (7.6 per cent). Amphibole also strongly influences the rock birefringence patterns. For both kind of rocks, the foliation is highly birefringent and the fast polarized shear wave is systematically oriented parallel to the foliation. We show that the number of mineral phases in the rock strongly controls the anisotropy. The seismic anisotropy has a complex role in the P-wave reflectivity. Compared to the isotropic case, anisotropy enhances the reflection coefficient for about 60 per cent of the possible lithological interfaces. For 40 per cent of the interfaces, the reflection coefficient is much lower when one considers the medium as anisotropic.
ISSN: 0956-540X

hal-01389122
http://hal.univ-reunion.fr/hal-01389122
http://hal.univ-reunion.fr/hal-01389122/document
http://hal.univ-reunion.fr/hal-01389122/file/Barruol_3D_velocities_GJI1993.pdf
DOI : 10.1111/j.1365-246X.1993.tb01519.x

Éditeur(s) : HAL CCSD Geological Society of London
Résumé : International audience
This paper presents the background for the calculation of various numbers that can be used to characterize crystal-preferred orientation (CPO), also known as texture in materials science, for large datasets using the combined scripting possibilities of MTEX and MatLab®. The paper is focused on three aspects in particular: the strength of CPO represented by orientation and misorientation distribution functions (ODFs, MDFs) or pole figures (PFs); symmetry of PFs and components of ODFs; and elastic tensors. The traditional measurements of texture strength of ODFs, MDFs and PFs are integral measurements of the distribution squared. The M-index is a partial measure of the MDF as the difference between uniform and measured misorientation angles. In addition there other parameters based on eigen analysis, but there are restrictions on their use. Eigen analysis does provide some shape factors for the distributions. The maxima of an ODF provides information on the modes. MTEX provides an estimate of the lower bound uniform fraction of an ODF. Finally, we illustrate the decomposition of arbitrary elastic tensor into symmetry components as an example of components in anisotropic physical properties. Ten examples scripts and their output are provided in the appendix.
Geological Society Special Publication

hal-01277689
https://hal.archives-ouvertes.fr/hal-01277689
DOI : 10.1144/SP409.8

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We use 3-D mechanical modeling representing faults as planar surfaces with frictional properties that obey Coulomb-failure process to explore the long-term slip rates of the Altyn Tagh fault and Kunlun faults in the north Tibetan plateau. Crustal theology is simplified as an elastoplastic upper crust and a viscoelastic lower crust. Far-field GPS velocities and late Quaternary fault slip rates are used to constrain the model results. Rheological tests show that effective fault friction lower than 0.1-0.08 leads to high slip rates that fit with geologically and geodetically determined slip rates of the Kunlun fault (10-11.7 +/- 1.5 mm/yr). Meanwhile, the modeled Altyn Tagh fault reaches slip rates similar to 13.7 mm/yr to similar to 7.8 mm/yr in its central portion, between ranges of the geological slip rates. Associated with high slip rates, our model predicts that central Tibet (similar to 84 degrees E-95 degrees E) from the Altyn Tagh fault to the north of the Himalayan arc accommodates north-south shortening and east-west extension rates of similar to 10-12 mm/yr and similar to 8-10 mm/yr, respectively. We also question the widely accepted idea that interseismic strain is driven at the base of the seismogenic zone by a screw dislocation. If this assumption fails, the presented model implies that interseismic strain around large strike-slip faults could be distributed in a much broader way if the lithosphere deforms as a thin elastic plate rather than an elastic half-space with an embedded dislocation. If this distributed deformation is ignored, and the instantaneous surface deformation field modeled as that resulting from slip on a dislocation below a specified depth embedded in an elastic half-space, the estimated slip rate will inevitably be lower than the true long-term slip rate. This appears to explain why geodetic slip rates proposed for the Altyn Tagh fault (510 mm/yr) are lower than some of the geological slip rates. (C) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00411926
https://hal.archives-ouvertes.fr/hal-00411926
DOI : 10.1016/j.epsl.2008.06.049

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Studies on tree biomechanical design usually focus on stem stiffness, resistance to breakage or uprooting, and elastic stability. Here we consider another biomechanical constraint related to the interaction between growth and gravity. Because stems are slender structures and are never perfectly symmetric, the increase in tree mass always causes bending movements. Given the current mechanical design of trees, integration of these movements over time would ultimately lead to a weeping habit unless some gravitropic correction occurs. This correction is achieved by asymmetric internal forces induced during the maturation of new wood. The long-term stability of a growing stem therefore depends on how the gravitropic correction that is generated by diameter growth balances the disturbance due to increasing self weight. General mechanical formulations based on beam theory are proposed to model these phenomena. The rates of disturbance and correction associated with a growth increment are deduced and expressed as a function of elementary traits of stem morphology, cross-section anatomy and wood properties. Evaluation of these traits using previously published data shows that the balance between the correction and the disturbance strongly depends on the efficiency of the gravitropic correction, which depends on the asymmetry of wood maturation strain, eccentric growth, and gradients in wood stiffness. By combining disturbance and correction rates, the gravitropic performance indicates the dynamics of stem bending during growth. It depends on stem biomechanical traits and dimensions. By analyzing dimensional effects, we show that the necessity for gravitropic correction might constrain stem allometric growth in the long-term. This constraint is compared to the requirement for elastic stability, showing that gravitropic performance limits the increase in height of tilted stem and branches. The performance of this function may thus limit the slenderness and lean of stems, and therefore the ability of the tree to capture light in a heterogeneous environment.
ISSN: 0022-5193

hal-00534316
https://hal.archives-ouvertes.fr/hal-00534316
DOI : 10.1016/j.jtbi.2008.10.011

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD
Résumé : The geological storage of CO 2 is considered as one of the solutions to the problem of global warming. The most possible scenarios of geological behavior of soil in the long term conditions has to be precisely defined to avoid catastrophic damages in the future. Chemical properties of saline water in the aquifer after the CO 2 injection becomes more acidic with time. Therefore, chemical degradation of rock occurs, which leads to modifications of its mechanical properties (chemo-mechanical coupling) [1]. In this paper an incremental model of chemo-mechanical coupling using homogenization approach (asymptotic expansion method [2,3]) is proposed. The paper is focused on the numerical computations for the X-ray tomography image of carbonate rock microstructure [4]. The chemical degradation of the microstructure is obtained as a homogeneous dissolution in each direction (Fig.1. – Fig.2.) For every porosity state numerical computations to obtain full, orthotropic elasticity tensor are performed. Therefore, the degradations functions for all components of the rigidity tensor were defined (Fig.3.). Moreover, results of numerical calculations of diffusion, tortuosity and permeability tensors are presented [5,6]. The link between geometrical properties and mechanical and transport parameters are discussed. The numerical analysis of the carbonate rock sample in long term conditions shows the increase of porosity and associated mechanical weakening of the rock. Moreover, the increase of diffusion, tortuosity and permeability tensors elements with time were observed. Finally, the solution of the one-dimensional macroscopic problem of soil settlement due to chemical dissolution of rock at constant load is presented. The method is universal, in the sense that the non-dimensional time scale is used.
ALERT Workshop 2013
Aussois, France

hal-01103175
https://hal.archives-ouvertes.fr/hal-01103175

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Springer-Verlag
Résumé : International audience
High-resolution borehole strainmeters are usually installed in tectonically active regions in order to detect slow-slip events, and to estimate slow transients related to earthquake swarms. However, they are also sensitive to other numerous influences, internal or external. Furthermore, the quality of their coupling to the rock through cementation, and the mechanical properties of the rock mass around them, have a critical influence on their records. Many of the existing strainmeters present such problems, and the correction for these effects often remains a challenge. In this paper, we present the analysis of the records of a high-resolution borehole dilatometer (Sacks–Evertson), located in the seismically active rift of Corinth (Greece) (station TRZ in the Trizonia island). We show that the instrument suffers from an only partial-solid coupling, and that the nearby sea tides have a direct (through elastic response) and indirect (through pore-pressure diffusion) effect on the dilatation signal, which adds up to the solid tidal strain source. We propose a methodology that allows, in a first step, to better separate the internal (solid tide) from the external (air pressure, sea level) influences, by calculating a frequency-dependent transfer function outside the range of the tidal periods. We then extrapolate this function, in particular at the tidal periods. In a second step, the resulting variation with frequency of the coupling coefficients with sea level led us to estimate the proportion of instrument not solidly cemented to rock (thus in contact with water pore pressure), which is about 90 % of the total height. Despite the small proportion of solid coupling, the sensor resolution remains very good up to a few tens of hours of a time period, thanks to the confining effects of the rocks on the local pore pressure. These results allow us to correct for the external effects, and reduce the associated variance by 80–90 % (in the period range of minutes to days). The empirical correction of the sea level effect could be explained using a simple Boussinesq’s approximation and 1D pore-pressure diffusion model, which contributed to better constraint of some of the poro-elastic parameters in the vicinity of the instrument. After correction, the solid tidal signal at the 24-h period is almost anti-correlated with those of the theoretical solid tide. This surprising result is consistent with a similar anti-correlation observed for the longest period surface waves (200 s) comparing the TRZ dilatometer signals to the strain measured by a nearby borehole strainmeter (MOK, 15 km). This could be related to the presence of a shallow fault close to the instrument, which would creep in response to seismic wave-related stress.
ISSN: 0033-4533

hal-01122853
https://hal.archives-ouvertes.fr/hal-01122853
DOI : 10.1007/s00024-013-0742-2

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Few studies have investigated the influence of environmental conditions on the within-treevariation in Eucalyptus wood traits. The genotype and environment effects and their interactionsinfluence the wood properties. Their evaluations are crucial to estimate the genotype values andto select with efficiency. Thus, the aim of this study was to better understand the effect ofground slope and wind speed on the spatial variation of basic density (ρ), stiffness (MOE) andmicrofibril angle (MFA) of Eucalyptus wood. Wood discs cut along the trunk were sampledfrom 150 six-year-old Eucalyptus grandis x E. urophylla hybrids growing in 3 contrastinggrowing conditions influenced by ground slope and wind regime. Near Infrared (NIR)calibrations previously developed for ρ, MOE and MFA were used to predict in our discs. 2-Dplots presenting the spatial variation of predicted wood traits were compared. The higher theground slope, the greater the magnitude of radial variation in ρ, principally in the medium zoneof the trunk. The spatial variation of wood stiffness seems to be sensitive to two environmentalconditions. The MFA radial decreases were more pronounced where the wind speed was higher.At the base and top of the trees, however, there was no significant effect of growing conditionson the radial variation of the wood properties considered here.
ISSN: 0931-1890

hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896/document
https://hal.archives-ouvertes.fr/hal-01451896/file/Art_Gril_al_Spatial_variation_wood_density_2016.pdf
DOI : 10.1007/s00468-015-1327-8

Éditeur(s) : HAL CCSD
Résumé : This work provides new constraints on the development and on the distribution of the deformation in the upper mantle and particularly beneath transform plate boundaries. USArray experiment and the remarkable increase of the dataset in California for the past ten years allowed us to scrutinize the lateral variations of the anisotropy in the vicinity of the San Andreas Fault zone. We have confirmed and increased the detection of two layers of anisotropy beneath this plate boundary. The first layer, located in the lithosphere, is related to the deformation induced at the fault, and the other one, located in the asthenosphere, is coherent with the anisotropy observed far from it, its origin is however less clear. We show that the deformation zone associated both to the San Andreas, Calaveras and Hayward Faults, is likely 40 km wide at 70 km depth. We then performed numerical thermomechanical modeling (ADELI) of the displacement of a transform plate boundary associated with the computation of the development of crystallographic fabrics using a viscoplastic selfconsistent approach (VPSC). We analyzed the distribution of the deformation in the model ant looked after the possible interactions at depth between deformation caused at surface by the strike-slip dynamic of the fault and the shearing at the base of the lithosphere caused by the horizontal displacement of the plates. Elastic properties derived from the crystallographic fabrics modeled, show that such interactions exist and induce, beneath the fault zone, a progressive rotation of the crystallographic fabrics with depth. Seismological signature of these smooth rotations is however not relevant with the presence of two anisotropic layers as proposed beneath California. We thus consider that a decoupling zone exists between the lithosphere and the asthenosphere beneath the California to account for the sharp separation between a lithospheric and an asthenospheric deformation. We furthermore estimate that anisotropy observed far form the San Andreas Fault in California cannot be explained only by the drag of the asthenosphere by the North America lithosphere as proposed in our article. Indeed, we can only expect few tenths of second of splitting delay from the anisotropic properties derived from the numerical modeling of a plate moving in the same direction and in the same velocity than the North American lithosphere only for 10 Ma of displacement. As delays observed in California rather reach 1.5 s, anisotropy in this region thus requires the existence of an active asthenospheric flow to be explained.
Le travail réalisé pendant cette thèse a permis d'apporter de nouvelles contraintes sur le développement et la distribution de la déformation dans le manteau supérieur et plus particulièrement au niveau des grandes limites de plaques décrochantes. Grâce à l'apport de l'expérience USArray et d'une dizaine d'années d'enregistrements sismologiques supplémentaires, nous avons pu étudier, de manière précise, les variations d'anisotropie dans le voisinage de la Faille de San Andreas. Nous avons confirmé et étendu l'observation de deux couches anisotropes sous cette limite de plaque. On y observe une première couche localisée dans la lithosphère marquant la déformation induite à la limite de plaque, et une autre, asthénosphérique, cohérente avec l'anisotropie observée loin de la faille et d'origine plus discutée. Nous avons montré que la zone de déformation associée aux failles de San Andreas, Calaveras et d'Hayward a, vraisemblablement, une largeur d'au moins 40 kilomètres en base de lithosphère, sous chacune de ces failles. Nous avons ensuite procédé à la modélisation thermomécanique (ADELI) de la migration d'une limite de plaques décrochante couplée à une modélisation du développement de fabriques cristallographiques par une approche viscoplastique auto-cohérente (VPSC). Ceci nous a permis d'y observer le développement de la déformation et les conséquences des possibles interactions entre la déformation décrochante en surface et le cisaillement en base de lithosphère dû au déplacement horizontal des plaques. Les propriétés élastiques déduites des fabriques cristallographiques modélisées montrent que de telles interactions existent et provoquent, sous la limite de plaques, une rotation des orientations cristallographiques avec la profondeur. Le signal associé à ces rotations progressives n'est toutefois pas cohérent avec la présence de deux couches d'anisotropie comme proposée sous la faille de San Andreas. Nous pensons par conséquent qu'il existe, sous la Californie, une zone de découplage entre la lithosphère et l'asthénosphère, permettant d'individualiser une déformation lithosphérique d'une déformation asthénosphérique. Nous estimons, en outre, que l'anisotropie observée dans l'asthénosphère sous la Californie ne peut être expliquée seulement par le cisaillement induit par le déplacement de la lithosphère Nord Amérique. En effet, les propriétés anisotropes obtenues par modélisation à partir d'une plaque se déplaçant dans une direction et une vitesse proche de celle de la plaque Amérique du Nord montrent qu'on ne peut espérer guère plus que quelques dixièmes de seconde de délai au bout de 10 Ma de déplacement. Les déphasages mesurés en Californie étant de l'ordre de 1,5 s, il est donc nécessaire d'invoquer la présence d'écoulements mantelliques actifs sous cette région.
https://tel.archives-ouvertes.fr/tel-00767124

tel-00767124
https://tel.archives-ouvertes.fr/tel-00767124
https://tel.archives-ouvertes.fr/tel-00767124/document
https://tel.archives-ouvertes.fr/tel-00767124/file/theseBonnin.pdf

Éditeur(s) : HAL CCSD
Résumé : Among erosion processes, river incision is classicaly described as a key process controlling erosion of landscapes. Incision efficiency is mainly influenced by climate and erodibility. This latter is not only dependent on the nature of the bedrock, but also on its past deformation, which affects its rheological effective properties, such as fracture density. The main objectives of this thesis are: (1) to better constrain the relationship between effective properties and erodibility, and (2) to quantify the influence of erodibility and erosion on both the temporal and spatial building or decay of the topography. Several numerical tools are developed. A 1D formalism of landscape evolution is introduced, including river incision with stochastic distribution of water discharge and hillslope landsliding. A new remeshing algorithm called Surface Lagrangian Remeshing (SLR) is developed as a complement to remeshing algorithms dealing with internal elements. It allows one to take into account long-term erosion into 2D Lagrangian numerical codes based on triangular finite elements. Then the potentiality of measuring erodibility in-situ using a Schmidt hammer (R) is assessed for the active orogen of Taiwan, the diagenetic Annot sandstones and St Clement fault zone. Results suggest a strong control of R by effective properties. A linear model based on effective medium theory is applied to a fault zone with an unmacthed resolution (750 measures, 25 measures per square meter). The model successfully correlates R to fracture density. These results demonstrate that effective elasticity as well as erodibility are sensitive to the density and type of fractures. Finally I focus on the erosional and rheological conditions that allows reproducing post-orogenic evolution of mountain belts. A model coupling surface erosion and regional isostatic uplift is consistent with observations. The topographic decay and decrease of the ratio of surface elevation over crustal root thickness is at first order controlled by the initial geometry of the mountain belt and erosion efficiency. This new model highlights the control ofclimate and erodibility on the topographic decay and of lithospheric rheology on the perseverance of crustal roots.
Parmi les processus d'érosion, l'incision des rivières est classiquement décrit comme un processus clé contrôlant l'érosion des paysages. L'efficacité de l'incision est principalement influencée par le climat et par l'érodabilité. Ce dernier paramètre ne dépend pas seulement de la nature du substratum rocheux, mais aussi de sa déformation passée qui affecte ses propriétés rhéologiques équivalentes. Les principaux objectifs de cette thèse sont: (1) de mieux contraindre les relations entre propriétés équivalentes et érodabilité, et (2) de quantifier l'influence de l'érosion et de l'érodabilité sur la formation ou la décadence, spatiale et temporelle, de la topographie. Plusieurs outils numériques sont développés. Un formalisme 1D d'évolution des paysages est proposé, prenant en compte simultanément l'incision des rivières avec une distribution stochastique des débits en eau et l'érosion des versants par glissements de terrain. Un nouvel algorithme de remaillage appelé Surface Lagrangian Remeshing (SLR) est développé. Il permet de prendre en compte l'érosion à long terme dans les codes numériques 2D Lagrangiens basés sur des éléments finis triangulaires. Ensuite, la possibilité de mesurer in-situ l'érodabilité avec un marteau de Schmidt (R) est évaluée pour: l'orogène actif de Taiwan, les grès diagénétiques d'Annot et la zone de faille de St Clément. Les résultats suggèrent un fort contrôle de R par les propriétés équivalentes des roches testées. Un modèle linéaire, basé sur la théorie des milieux équivalents, est appliqué à une zone de faille avec une résolution inégalée (750 mesures, 25 mesures par mètre carré). Le modèle permet de corréler avec succès la densité de fracture et R. Ces résultats démontrent empiriquement que l'élasticité équivalente ainsi que l'érodabilité sont sensibles à la densité et à la nature des fractures. Enfin j'étudie les conditions d'érosion et de rhéologie qui permettent de reproduire l'évolution des chaînes de montagnes post-orogéniques. Un modèle couplant érosion en surface et soulèvement isostatique régional est compatible avec les observations. Les taux de décroissance topographique et de diminution du rapport de l'élévation de surface sur l'épaisseur de racine crustale sont contrôlés au premier ordre par la géométrie initiale de la chaîne de montagne et par l'efficacité de l'érosion. Ce nouveau modèle met en évidence le contrôle du climat et de l'érodabilité sur la décroissance topographique et de la rhéologie lithosphérique sur la persévérance des racines crustales.
https://tel.archives-ouvertes.fr/tel-00602341

tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341/document
https://tel.archives-ouvertes.fr/tel-00602341/file/thesephilippesteer.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Energy dissipation is observed on seismic data when a wave propagates through a porous medium, involving different frequency regimes depending on the nature of rock and fluid types. We focus here on the role of partial fluid saturation in unconsolidated porous media, looking in particular at P-wave phase velocity and attenuation. The study consists in running an experiment in a sand-filled tank partially saturated with water. Seismic propagation in the tank is generated in the kHz range by hitting a steel ball on a granite plate. Seismic data are recorded by buried accelerometers and injecting or extracting water controls the partial saturation. Several imbibition/drainage cycles were performed between the water and gas residual saturations. A Continuous Wavelet Transform applied on seismic records allowed us to extract the direct P-wave at each receiver.We observe an hysteresis in phase velocities and inverse quality factors between imbibition and drainage. Phase velocities and inverse quality factors are then jointly inverted to get a final poro-visco-elastic model of the partially saturated sand that satisfactorily reproduces the data. The model formulation consists in generalizing the Biot theory to effective properties of the fluid and medium (permeability and bulk modulus) in order to properly explain the phase velocity variation as a function of the saturation. The strong level of attenuation measured experimentally is further explained by an anelastic effect due to grain to grain sliding, adding to Biot's losses. This study shows that fluid distribution at microscopic scale has strong influence on the attenuation of direct P-waves at macroscopic scale and confirms that seismic prospection may be a powerful tool for the characterization of transport phenomena in porous media.
ISSN: 0956-540X

hal-00779920
https://hal.archives-ouvertes.fr/hal-00779920
https://hal.archives-ouvertes.fr/hal-00779920/document
https://hal.archives-ouvertes.fr/hal-00779920/file/Barriere_et_al_HAL.pdf
DOI : 10.1111/j.1365-246X.2012.05691.x

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé :  
On 10 trees from 10 species of French Guyana tropical rainforest in a clear active process of restoring verticality growth strains were measured in situ in order to determine the occurrence of tension wood within samples. Wood specimens were cut in the vicinity of the growth strains measurements in order to measure some mechanical and physical properties. As suspected, tensile growth strains was very much higher in tension wood zone, because longitudinal modulus of elasticity was slightly higher. Longitudinal shrinkage was also much higher in tension wood than in opposite wood.
ISSN: 1286-4560

hal-01032110
https://hal.archives-ouvertes.fr/hal-01032110
DOI : 10.1051/forest:2007027

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : This study presents a unique database of 172 plagioclase Crystallographic Preferred Orientations (CPO) of variously deformed gabbroic rocks. The CPO characteristics as a function of the deformation regime (magmatic or crystal-plastic) are outlined and discussed. The studied samples are dominantly from slow- and fast-spread present-day ocean crust, as well as from the Oman ophiolite. Plagioclase is the dominant mineral phase in the studied samples. Plagioclase CPOs are grouped into three main categories: Axial-B, a strong point alignment of (010) with a girdle distribution of [100]; Axial-A, a strong point maximum concentration of [100] with parallel girdle distributions of (010) and (001); and P-type, point maxima of [100], (010), and (001). A majority of CPO patterns are Axial-B and P-type, in samples showing either magmatic or crystal-plastic deformation textures. Axial-A CPOs are less common; they represent 21% of the samples deformed by crystal-plastic flow. Although fabric strength (ODF J index) does not show any consistent variation as a function of the CPO patterns, there is a significant difference in the relationship between the ODF and pole figures J indices; the magmatic type microstructures have high (010) pole figures J indices, which increase linearly with ODF J index, whereas the high [100] pole figures J indices of plastically deformed samples vary in a more scattered manner with ODF J index. The multistage nature of plastic deformation superposed on a magmatic structure compared with magmatic flow, and the large number of possible slip-systems in plagioclase probably account for these differences. Calculated seismic properties (P wave and S wave velocities and anisotropies) of plagioclase aggregates show that anisotropy (up to 12% for P wave and 14% for S wave) tends to increase as a function of ODF J index. In comparison with the olivine 1998 CPO database, the magnitude of P wave anisotropy for a given J index is much less than olivine, whereas it is similar for S wave anisotropy. Despite a large variation of fabric patterns and geodynamic setting, seismic properties of plagioclase-rich rocks have similar magnitudes of anisotropy. There is a small difference in the aggregate elastic symmetry, with magmatic microstructures having higher orthorhombic and hexagonal components, whereas plastic deformation microstructures have a slightly higher monoclinic component, possibly correlated with predominant monoclinic simple shear flow in plastically deformed samples. Overall, plots for CPO strength (ODF J index), pole figure strength, CPO symmetry and seismic anisotropy show significant scattering. This could be related to sampling statistics, although our database is a factor of ten higher than the olivine database of 1998, or it could be related to the low symmetry (triclinic) structure of plagioclase resulting in the addition of degrees of freedom in the processes creating the CPOs.
ISSN: 1869-9510

hal-00963439
https://hal.archives-ouvertes.fr/hal-00963439
DOI : 10.5194/se-4-511-2013

Éditeur(s) : HAL CCSD
Résumé : The forests of French Guiana occupy a central part of the region’s potential resource base, but as yet remain almost completely unexploited. This stems from the forestry industry struggling to valorize wood stocks of a high diversity with an extremely heterogeneous distribution. Indeed, identifying essences for future propagation is an issue of both environmental and socio-economic importance for the region. Bagassa guianensis Aubl. and Cordia alliodora (Ruiz & Pav.) Oken. go against conventional models, in that they display the life history characteristics of rapid growth and wood of high quality, and thus are species of high potential for future plantations. Firstly, our study of growth characteristics reveals a defined strategy half way between long-lived species and pioneer species. It is the variability of basic density of wood which is a key trait allowing for such a development, favoring rapid growth in initial years whilst allowing for tree longevity. Secondly, the analysis of a range of wood properties (shrinkage, modulus of elasticity, durability) in relation to tree growth confirms the technologic quality of the two species. It also enables the emergence of new results like the effect of extractives on wood stability, the control of growth as a result of basic density variation, the evolution of leaf traits throughout tree development or the improvement of trunk maintenance thanks to interlocked grain. The knowledge gained in relation to the developmental traits of these two species, and to the quality of their wood allows for the elaboration of plantation projects and what will be required for their success. The results of this study can orientate future studies on novel species for commercialization in French Guiana.
La ressource forestière en Guyane occupe une place maîtresse au sein de la région et est encore majoritairement préservée, mais la filière bois parvient difficilement à valoriser la biodiversité locale en raison de l’hétérogénéité de la ressource. Identifier les essences à planter demain représente aujourd’hui un enjeu à la fois environnemental, économique et social pour la Guyane. Bagassa guianensis Aubl. et Cordia alliodora (Ruiz & Pav.) Oken. vont à l’encontre des modèles usuels en associant vitesse de croissance et qualité du bois et sont identifiées comme prometteuses pour la plantation. Dans un premier temps, l’étude de la dynamique de croissance des deux espèces révèle un modèle écologique singulier, à la fois pionnières et longévives. La variabilité de l’infradensité dans l’arbre est l’élément clé qui permet un tel développement, favorisant une croissance rapide dans les premières années tout en assurant la longévité de l’individu. Dans une seconde partie, l’analyse d’un large panel de propriétés du bois (retrait, module, durabilité) en lien avec le développement de l’arbre confirme les qualités technologiques des deux espèces et permet l’émergence de résultats novateurs tels que le rôle des extractibles sur le retrait, le contrôle de la croissance grâce aux variations d’infradensité, l’évolution des traits foliaires au cours de l’ontogénie ou encore la mise en place de contrefil dans l’arbre pour assurer son maintien. La connaissance acquise vis-à-vis du mode de développement de ces deux espèces et des facteurs influençant la qualité de leur bois permet aujourd’hui de définir avec plus de précision le cadre d’un projet de plantation et les conditions de son succès. Les résultats de cette étude permettent finalement d’orienter la recherche de nouvelles espèces d’avenir pour la plantation en Guyane.
https://tel.archives-ouvertes.fr/tel-01338281

tel-01338281
https://tel.archives-ouvertes.fr/tel-01338281
https://tel.archives-ouvertes.fr/tel-01338281/document
https://tel.archives-ouvertes.fr/tel-01338281/file/Th%C3%A8se%20Julie%20Bossu.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Tangential strains were measured with strain gauges at the surface of xylem and inner bark of saplings of Cryptomeria japonica D. Don. and Fagus silvatica L. during a pressurization test. The test consists in submitting the whole sapling to an artificially imposed hydrostatic pressure of increasing magnitude. The elastic response of the stems was found linear both at the surface of xylem and inner bark. A simple geometric model allows to compute radial strains in each tissue from tangential strain data. Inside inner bark, radial strains are much larger than tangential strains, because tangential strains are restrained by the core of wood. The material compliance of each tissue was computed as the ratio between the radial strain and the pressure that caused it. The material compliance of xylem is much lower than that of inner bark, but, as its thickness is much larger, its contribution to the apparent behavior of the stem is not negligible. Computation of material compliances by this pressurization test provides information about the specific behavior of each tissue in response to hydrostatic pressure. This can be used to estimate and interpret the calibration factor linking the water status of the plant to the apparent strain measured at its surface.
ISSN: 0931-1890

hal-01031900
https://hal.archives-ouvertes.fr/hal-01031900
DOI : 10.1007/s00468-006-0061-7

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
A dense network of seismic stations has been deployed on the Kaapvaal craton (South Africa) to investigate the upper mantle seismic structures. In order to bring independent petrophysical constraints, we analyze a direct sampling of the cratonic upper mantle and determine the seismic properties of 48 mantle nodules brought up to the Earth's surface by kimberlite eruptions. Seismic properties of these nodules are calculated from the olivine and pyroxene crystal preferred orientations and the single crystal elastic constants. Despite variations in the nodules compositions, microstructures and crystallographic preferred orientations, seismic anisotropy is rather homogeneous throughout the craton. Mean S-wave anisotropy is weak (2.64 %), which is compatible with the small measured SKS wave splitting (mean delay time of 0.62 s).
ISSN: 0094-8276

hal-01389119
http://hal.univ-reunion.fr/hal-01389119
http://hal.univ-reunion.fr/hal-01389119/document
http://hal.univ-reunion.fr/hal-01389119/file/BenIsmail_GRL_kaapvaal_GRL2001.pdf
DOI : 10.1029/2000GL012419

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
Tree buckling risk (actual height/critical buckling height) is an important biomechanical trait of plant growth strategies, and one that contributes to species coexistence. To estimate the diversity of this trait among wide samples, a method that minimizes damage to the plants is necessary. On the basis of the rarely used, complete version of Greenhill's model (1881, Proceedings of the Cambridge Philosophical Society 4(2): 65-73), we precisely measured all the necessary parameters on a sample of 236 saplings of 16 species. Then, using sensitivity (variance) analysis, regressions between successive models for risk factors and species ranks and the use of these models on samples of self- and nonself-supporting saplings, we tested different degrees of simplification up to the most simple and widely used formula that assumes that the tree is a cylindrical homogeneous pole. The size factor had the greatest effect on buckling risk, followed by the form factor and the modulus of elasticity of the wood. Therefore, estimates of buckling risk must consider not only the wood properties but especially the form factor. Finally, we proposed a simple but accurate method of assessing tree buckling risk that is applicable to a wide range of samples and that requires mostly nondestructive measurements.
ISSN: 0002-9122

hal-01032059
https://hal.archives-ouvertes.fr/hal-01032059