Éditeur(s) : HAL CCSD
Résumé : International audience
The influence of Mn solute atoms on sub-grain boundary mobilities in Al has been determined by accurate electron backscatter diffraction analysis of the sub-grain sizes and misorientations during recovery annealing. High purity Al-0.1 and 0.3 wt.% Mn alloys were deformed by plane strain compression at room temperature to equivalent strains of 1.8 and annealed in the temperature range 150-300 °C. An original method of image analysis on sub-boundaries from electron backscatter diffraction maps was applied to quantify the sub-grain size distributions. The change in average sub-grain size with time at several temperatures was then used to estimate sub-grain boundary mobilities in both Al-Mn alloys. The activation energies for sub-grain mobility were found to be 48 and 52 and kJ.mol^-1 for the 0.1 and 0.3 % Mn alloys respectively, with the higher Mn alloy exhibiting lower rates. The sub-boundary mobilities are higher than expected from previous similar work on deformed Al-Si crystals. The orientation dependence of sub-grain growth is also examined.
International Journal of Materials Research

emse-00463551
https://hal-emse.ccsd.cnrs.fr/emse-00463551
DOI : 10.3139/146.110057

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
We use lithospheric-scale analog models to study the reactivation of pre-existing heterogeneities under oblique shortening and its relation to the origin of arcuate orogens. Reactivation of inherited rheological heterogeneities is an important mechanism for localization of deformation in compressional settings and consequent initiation of contractional structures during orogenesis. However, the presence of an inherited heterogeneity in the lithosphere is in itself not sufficient for its reactivation once the continental lithosphere is shortened. The heterogeneity orientation is important in determining if reactivation occurs and to which extent. This study aims at giving insights on this process by means of analog experiments in which a linear lithospheric heterogeneity trends with various angles to the shortening direction. In particular, the key parameter investigated is the orientation (angle α) of a strong domain (SD) with respect to the shortening direction. Experimental results show that angles α ≥ 75° (high obliquity) allow for reactivation along the entire SD and the development of a linear orogen. For α ≤ 60° (low obliquity) the models are characterized by the development of an arcuate orogen, with the SD remaining partially non-reactivated. These results provide a new mechanism for the origin of some arcuate orogens, in which orocline formation was not driven by indentation or subduction processes, but by oblique shortening of inherited heterogeneities, as exemplified by the Ouachita orogen of the southern U.S.
ISSN: 0278-7407

insu-01498544
https://hal-insu.archives-ouvertes.fr/insu-01498544
https://hal-insu.archives-ouvertes.fr/insu-01498544/document
https://hal-insu.archives-ouvertes.fr/insu-01498544/file/Calignano_et_al-2017-Tectonics.pdf
DOI : 10.1002/2016TC004424

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In this contribution we present a reconstruction of the overall lithotectonic architecture, from inner zones to external ones, of the Paleoproterozoic Trans North China Orogen, within the North China Craton. Moreover, forward thermobarometrical modeling on a kyanite-bearing gneiss yields a reliable prograde P-T-t-D path. In addition, 40Ar/39Ar dating on rocks from distinct litho-tectonic units helps us to distinguish several tectono-metamorphic events during the orogenic development. Considering these results, we propose a geodynamic model involving three cratonic blocks, namely the Western, Fuping and Eastern Blocks, separated by two oceans, the Lüliang and Taihang Oceans. The opening of oceanic basins occurred around 2.2-2.3 Ga. After the westward subductions of oceanic lithosphere, the Trans-North-China Orogen was built up through a polyphase tectonic evolution within the period 1900-1800 Ma. The first event (D1) corresponded to the emplacement of lower and upper nappes herein called the Orthogneiss-and-Volcanites Unit (OVU) and the Low-Grade-and-Mafic Unit (LGMU), respectively. The syn-metamorphic D1 deformation (1880 ± 10 Ma) is characterized by a NW-SE stretching and mineral lineation with a top-to-the SE sense of shear. During ongoing compression of the thickening orogenic crust, a second deformation event D2 (1850 ± 10 Ma) was responsible for (1) syn-anatectic lateral flow and exhumation of the orogenic root and (2) folding of the middle and upper parts of the orogenic wedge that consequently acquired a fan-type geometry. The late D3 (1830 ± 10 Ma) and D4 (1810 ± 10 Ma) events are related to late-orogenic normal and strike-slip shearing, respectively. In our present state of knowledge, the Paleoproterozoic Trans-North China Orogen might be regarded as the assemblage of two continent-continent collisional belts, both of which are characterized by nappe stacking accommodated by top-to-the E/SE ductile shearing. Continental subduction, crustal thickening, partial melting of overthickened crust, exhumation of HP rocks and deposition of syn-orogenic detrital basins are typical features of modern collisional-type orogens.
ISSN: 0301-9268

Droits : info:eu-repo/semantics/OpenAccess
insu-00628119
https://hal-insu.archives-ouvertes.fr/insu-00628119
https://hal-insu.archives-ouvertes.fr/insu-00628119/document
https://hal-insu.archives-ouvertes.fr/insu-00628119/file/Trap-PrecambrianResearch-2011.pdf
DOI : 10.1016/j.precamres.2011.09.008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Parentis and Arzacq-Mauleon basins located in front of the V-shaped oceanic propagator in the Bay of Biscay present evidence for extreme crustal thinning. In this paper we investigate the 3D structure of these rift basins, based on field observations and the interpretation of seismic data. We compare these results with those obtained from two different and independent inversion methods: first a 3D gravity inversion and second the standard Euler deconvolution.;For the Mauleon Basin our results show that the positive gravimetric anomaly identified above its southern margin is the consequence of two shallower high density bodies that are separated by the Pamplona fault and a deeper high density body. The high density bodies can be explained by the presence of mid-crustal and mantle rocks that were exhumed or uplifted at shallower depth during Early Cretaceous rifting before they were reworked and integrated to the Pyrenean chain during compression phase. Also, during this reactivation phase, some slices of the exhumed mid-crustal and mantle rocks were sheared off and were integrated in the present-day thrust belt in the Mauleon basin. For the Parentis Basin we can demonstrate, based on seismic data and gravimetric inversion methods, a decrease in extension from west to east, which is compatible with the V-shape geometry of the overall basin. Along strike, a change in the fault geometry from downward concave top-basement detachment faults to upward concave high-angle faults can be observed eastwards, i.e. towards the termination of the basin. A key structure, controlling the evolution of the Parentis Basin, is the east-west trending Ibis fault. We interpret this fault to have initially formed as a strike slip fault before it was reactivated during later crustal thinning. At present, it forms the limit between an upper plate sag basin to the north and a lower plate sag basin, floored at least locally by a top-basement detachment faults to the south. The strong asymmetry of the basin is supported by the shape of the basin and the results of standard Euler deconvolution.
ISSN: 0040-1951

hal-00523444
https://hal.archives-ouvertes.fr/hal-00523444
DOI : 10.1016/j.tecto.2010.04.023

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Active mechanisms of re-orientation are necessary to maintain the verticality of tree stems. They are achieved through the production of reaction wood, associated with circumferential variations of three factors related to cambial activity: maturation strain, longitudinal modulus of elasticity (MOE) and eccentric growth. These factors were measured on 17 mature trees from different botanical families and geographical locations. Various patterns of circumferential variation of these factors were identified. A biomechanical analysis based on beam theory was performed to quantify the individual impact of each factor. The main factor of re-orientation is the circumferential variation of maturation strains. However, this factor alone explains only 57% of the re-orientations. Other factors also have an effect through their interaction with maturation strains. Eccentric growth is generally associated with heterogeneity of maturation strains, and has an important complementary role, by increasing the width of wood with high maturation strain. Without this factor, the efficiency of re-orientations would be reduced by 31% for angiosperms and 26% for gymnosperms. In the case of angiosperms, MOE is often larger in tension wood than in normal wood. Without these variations, the efficiency of re-orientations would be reduced by 13%. In the case of gymnosperm trees, MOE of compression wood is lower than that of normal wood, so that re-orientation efficiency would be increased by 24% without this factor of variations.
ISSN: 0931-1890

hal-01031825
https://hal.archives-ouvertes.fr/hal-01031825
DOI : 10.1007/s00468-005-0407-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Alpine Corsica consists of a stack of variably metamorphosed units of continental and Tethys-derived rocks. It represents an excellent example of high-pressure (HP) orogenic belt, such as the Western Alps, exposed over a small and accessible area. Compared to the Western Alps, the geology of Alpine Corsica is poorly unraveled. During the 1970s-80s, based on either lithostratigraphic or metamorphic field observations, various classifications of the belt have been proposed, but these classifications have been rarely matched together. Furthermore, through time, the internal complexity of large domains has been progressively left aside in the frame of large-scale geodynamic reconstructions. As a consequence, major open questions on the internal structure of the belt have remained unsolved. Apart from a few local studies, Alpine Corsica has not benefited of modern developments in petrology and basin research. This feature results in several uncertainties when combining lithostratigraphic and metamorphic patterns and, consequently, in the definition of an exhaustive architecture of the belt. In this paper we provide a review on the geology of Alpine Corsica, paying particular attention to the available lithostratigraphic and metamorphic classifications of the metamorphic terranes. These data are completed by a new and exhaustive metamorphic dataset obtained by means of thermometry based on Raman Spectroscopy of Carbonaceous Material (RSCM). This technique provides reliable insights on the peak temperature of the metamorphic history for CM-bearing metasediments. A detailed metamorphic characterization of metasediments, which have been previously largely ignored due to retrogression or to the lack of diagnostic mineralogy, is thus obtained and fruitfully coupled with the available lithostratigraphic data. Nine main tectono-metamorphic units are defined, from subgreenschist (ca. 280-300 °C) to the lawsonite-eclogite-facies (ca. 500-550 °C) condition. These units are homogeneous in metamorphism, laterally continuous and have characteristic lithostratigraphic features. This study also suggests a direct link between the pre-orogenic extensional setting and the present-day compressional structure of Alpine Corsica, indicating that large sections of subducted lithosphere were subducted and exhumed as coherent domains. These features provide important insight on the mechanism of stacking and exhumation of HP rocks, and make Alpine Corsica a unique reference for mountain-building processes in Tethyan-type orogens.
ISSN: 0012-8252

hal-00814433
https://hal.archives-ouvertes.fr/hal-00814433
DOI : 10.1016/j.earscirev.2012.10.003

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
After the January 12, 2010, Haiti earthquake, we deployed a mainly offshore temporary network of seismologic stations around the damaged area. The distribution of the recorded aftershocks, together with morphotectonic observations and mainshock analysis, allow us to constrain a complex fault pattern in the area. Almost all of the aftershocks have a N‐S compressive mechanism, and not the expected left‐lateral strike‐slip mechanism. A first‐order slip model of the mainshock shows a N264°E north‐dipping plane, with a major left‐lateral component and a strong reverse component. As the aftershock distribution is sub‐parallel and close to the Enriquillo fault, we assume that although the cause of the catastrophe was not a rupture along the Enriquillo fault, this fault had an important role as a mechanical boundary. The azimuth of the focal planes of the aftershocks are parallel to the north‐dipping faults of the Transhaitian Belt, which suggests a triggering of failure on these discontinuities. In the western part, the aftershock distribution reflects the triggering of slip on similar faults, and/or, alternatively, of the south‐dipping faults, such the Trois‐Baies submarine fault. These observations are in agreement with a model of an oblique collision of an indenter of the oceanic crust of the Southern Peninsula and the sedimentary wedge of the Transhaitian Belt: the rupture occurred on a wrench fault at the rheologic boundary on top of the under‐thrusting rigid oceanic block, whereas the aftershocks were the result of the relaxation on the hanging wall along pre‐existing discontinuities in the frontal part of the Transhaitian Belt.
ISSN: 0094-8276

insu-00643489
https://hal-insu.archives-ouvertes.fr/insu-00643489
https://hal-insu.archives-ouvertes.fr/insu-00643489/document
https://hal-insu.archives-ouvertes.fr/insu-00643489/file/GRL-haiti.2011.pdf
DOI : 10.1029/2011GL049799

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
S U M M A R Y Over the last decade, thermomechanical models have revealed the control of both tectonics and erosion on the morphology of continental plateaus margins. However, unravelling the specific effects of these two coupled processes has been difficult in practice. Here, to assess the control of erosion, we investigate the dynamics of the eastern and the northern borders of the Tibetan Plateau, which are characterized by a low convergence rate and a steep topographic escarpment adjacent to the Sichuan and Tarim basins, respectively. Thermomechanical modelling of continental lithosphere coupled with fluvial denudation reveals that important crustal deformation with large-scale horizontal displacements can occur, without any convergence, as a response to mass transfer due to gravitational collapse and to erosional unloading. These processes are sensitive to crustal structure, geothermal gradient as well as surface erosion. At a timescale of several million years, our results suggest that this denudation-triggered deformation exerts a primary control on the evolution of those plateau margins by counterbalancing the mass removal due to erosion and stabilizing the topographic escarpment. This finding supports a possible explanation for the morphology of the Longmen Shan, eastern Tibet, in which the paradoxical combination of persistent high-topographic gradients close to the foreland and low convergence rates can be related to the influence of erosion on deformation patterns.
ISSN: 0956-540X

hal-01577060
https://hal-amu.archives-ouvertes.fr/hal-01577060
https://hal-amu.archives-ouvertes.fr/hal-01577060/document
https://hal-amu.archives-ouvertes.fr/hal-01577060/file/godard2009erosional.pdf
DOI : 10.1111/j.1365-246X.2009.04324.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We conducted triaxial compression experiments to investigate the effects of pressure, temperature and strain rate on the rheology of talc rocks. The tests were carried out at T from 25 to 860 degrees C, P from 0.1 to 300 MPa, and <(epsilon) over dot> from 0.3 to 30 x 10-5 s(-1). In addition to being very weak, there are other important differences between the mechanical behavior of talc and that of most other silicates. Deformation at all temperatures up to dehydration was accommodated by a combination of crystal plasticity, frictional sliding, and cataclasis. A transition from localized to distributed deformation occurred at P = 300 MPa and T = 400 degrees C, but this transition is ill-defined as both distributed and localized deformation were observed at P = 300 MPa and T = 600 degrees C. Unlike most silicates, both the coefficient of internal friction and the coefficient of (sliding) friction are very low and nearly equal to each other. Temperature enhances plastic deformation (kinking), and inter- and intra-granular microcracks are observed parallel to the (001) planes at all conditions. Voids are created by delamination along (001) planes at kink-band boundaries. Full crystal plasticity was not achieved under any of the conditions tested, i.e., the von Mises criterion was never satisfied. However, the strength of the aggregates remained much less than the confining pressure. These unusual properties are likely a manifestation of the pronounced mechanical anisotropy of talc at the grain scale. At T >= 750 degrees C dehydration is observed, but only along shear zones. These results suggest that feedbacks between deformation and reaction kinetics could control fluid flow in fault zones. The presence of talc can promote significant weakening and strain localization in the oceanic lithosphere, the subducting plate and the overlying mantle wedge. (c) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00492706
https://hal.archives-ouvertes.fr/hal-00492706
DOI : 10.1016/j.epsl.2008.02.004

Éditeur(s) : HAL CCSD
Résumé : The territory of Armenia was located in the collision zone between Arabia and Eurasia, and is the seat of active intercontinental deformations, which was attested by the many historical earthquakes that have occurred in this region. All these destructive earthquakes show a strong regional seismic activity, and therefore it is important to evaluate the seismic hazard associated with active structures that generates this seismicity.This study presents the results of the analysis of the active tectonics within the northwestern and southeastern extensions of the Pambak-Sevan-Syunik fault (PSSF), a major right-lateral strike-slip fault cutting through Armenia (NW - SE). Quantifying the deformations in terms of geometry, kinematics, slip rates and earthquake activity, using cosmogenic 3He, OSL/IRSL and radiocarbon dating techniques, reveal different behaviors between the two regions.Within the northwestern extension, in the region of Amassia, the PSSF bends to the west and splits into two main WNW-ESE trending reverse faults defining a compressional pop-up structure. We estimate an uplift rate and a shortening rate of 0.5 ± 0.1 mm/y and 1.4 ± 0.6 mm/y, respectively. This suggests that most of the ~2 mm/y right lateral movement of the PSSF seems to be absorbed within the Amasia pop-structure.Within the southeastern extension, in the region of Tsghuk volcano, the PSSF shows signs of dying out at the southernmost tip of the Syunik graben. A very slow NS trending normal faulting associated with a slight right-lateral movement characterizes the tectonic activity in the region of Tsghuk volcano. We estimate vertical slip rates, EW stretching rate, and right-lateral slip rate of ~0.2 mm/y, ~0.1 mm/y and ~0.05 mm/y, respectively. These results lead to the conclusion that the right lateral movement observed further north along the PSSF is mainly transferred within other active faults further west within the Karabagh (Hagari fault or other structures further northwestwards).
L’Arménie se situe dans la zone de collision entre Arabie et Eurasie et est le siège d’une déformation intracontinental active comme l’atteste les nombreux tremblements de terre historiques qui s’y sont produits. Tous ces séismes, destructeurs, attestent d’une forte activité sismique régionale, et il est par conséquent important d'évaluer l’aléa sismique associé aux structures actives qui génère cette sismicité.Le travail présenté ici, expose les résultats de l’analyse de la tectonique active au niveau des terminaisons nord-ouest et sud-est de la faille de Pambak-Sevan-Syunik (PSSF), une des failles décrochant majeure qui traverse l'Arménie du NW au SE. La quantification des déformations en termes de géométrie, cinématique, vitesse de glissement et paléosismicité, en utilisant les méthodes de datation 3He cosmogénique, OSL/IRSL et radiocarbone, révèlent des comportements différents entre les deux régions.Au niveau de la terminaison nord-ouest, dans la région d’Amassia, la faille PSSF s’incurve vers l'ouest et se subdivise en deux branches de direction WNW-ESE, et de cinématique inverse, définissant une structure en pop-up. Nous estimons une vitesse de soulèvement de 0.5 ± 0.1 mm/an et une vitesse de raccourcissement NNE-SSW de 1.4 ± 0.6 mm/an. Ces résultats suggère que l’essentiel des ~2 mm/an de mouvement dextre estimés le long de la faille de PSSF sont absorbés au niveau du pop-up d’Amassia.Au niveau de la terminaison sud-est, dans la région du volcan Tsghuk, la faille PSSF semble disparaitre. Le peu d’activité tectonique est caractérisée par des failles normales sub-méridiennes associées à une légère composante décrochant dextre. Nous déterminons une vitesse de glissement vertical de ~0,2 mm/an, une vitesse d’extension ~EW de ~0,1 mm/an associée à une composante dextre de ~0,05 mm/an. Ces résultats suggèrent que le mouvement dextre observé le long de la faille de PSSF plus au nord, a été transféré sur d'autres failles plus à l'ouest dans le Karabakh (faille Hagari ou autres structures situés encore plus au NW).
https://tel.archives-ouvertes.fr/tel-01621440

NNT : 2016MONTT152
tel-01621440
https://tel.archives-ouvertes.fr/tel-01621440
https://tel.archives-ouvertes.fr/tel-01621440v2/document
https://tel.archives-ouvertes.fr/tel-01621440/file/2016_MKRTCHYAN_archivage.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper focuses on the analyses of the clastic sedimentary infill of the Coastal Plain of Eastern Mexico, which initiated synchronously with the Laramide orogeny in the vicinity of the Golden Lane. Results of these analyses are used as boundary conditions for calibrating/interpreting seismic profiles across more distal depocenters in the offshore of the Gulf of Mexico, from the sea shore and continental slope in the west to the abyssal plain in the east. The objective of the study is to better predict the reservoir distribution in the Deep offshore Basin of the Gulf of Mexico (DBGM), in order to explore for petroleum. The Coastal Plain is underlain by three morpho-tectonic domains: the tectonic front of the Sierra Madre Orientale (SMO), the Chicontepec deep water flexural basin, and the Tuxpan Platform (also known as the Golden Lane). Each domain is characterized by a distinct, dominantly siliciclastic Cenozoic lithostratigraphy. After a Jurassic rifting episode, followed by thermal subsidence, the oceanic basin and its western passive margin were deformed during the Upper Cretaceous and Paleogene, by far field stresses associated with the Cordilleran-Laramide Orogeny. Starting in the Late Cretaceous-Early Paleogene and during the Early Eocene, the tectonic load associated with the Laramide Orogen (Sierra Madre Oriental, SMO) caused flexural subsidence of the foreland located under the Coastal Plain. During this period, a massive transfer of siliciclastic sediments occurred from the Laramide foothills into the adjacent foreland. Sediments were eroded of the Sierra Madre tectonic wedge. Loading by these sediments pushed source units associated with the former passive margin down ward. The first syn-tectonic sediments of the Laramide orogeny were turbiditic silt layers in submarine fans which record also numerous collapse episodes and gravity slides. During the Late Eocene and Oligocene, the flexural subsidence stopped in the hinterland, whereas the subsidence of the passive margin resumed. This resulted in a change in the overall sedimentary architecture of the basin. Paleo-highs and reefs facies of the Golden Lane were flooded. Clastics by-passed the reefs and progradational clastic stratification formed as sediment moved towards the DBGM in the east. The final depositional environment of the continental platform/Coastal Plain became deltaic, marked by a succession of sand bars, levees and channels systems. From Miocene times onward, a system of gravitational listric faults developed near the platform to slope transition, resulting in a coeval compressional system at the transition between the slope and the abyssal plain. This system is driven by sediments charge. Because the sedimentation rate is larger than the subsidence, a large amount of clastics and slumped sediments are deposited in hangingwall basins.
ISSN: 0264-8172

hal-00424586
https://hal.archives-ouvertes.fr/hal-00424586
DOI : 10.1016/j.marpetgeo.2008.03.009

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Intraplate deformation is most often linked to major stress applied on plate margins. When such intraplate events are accompanied by magmatism, the use of several dating methods integrated within a multidisciplinary approach can bring constraints on the age, nature and source mobilized for generating the magma and in turn on the nature of the intraplate deformation. This study focuses on the large gabbro Arrikine sill (35 km in extension) emplaced within the Silurian sediments of the western margin of the Murzuq cratonic basin in southeastern Algeria. Its emplacement is dated during the early Devonian (415-400 Ma) through the determination of a reliable paleomagnetic pole by comparison with the Gondwana Apparent Polar Wander Path (APWP). This age can be correlated with deep phreatic eruptions before Pragian time thought to be at the origin of sand injections and associated circular structures in Algeria and Libya. For the sill, the K–Ar age of 325.6 ± 7.7 Ma is related to a K-rich aplitic phase that has K-enriched by more than 20% the Devonian gabbro. Laser-ICP-MS U–Pb method dates only inherited zircons mostly at c. 2030 Ma with additional ages at c. 2700 Ma and younger ones in the 766-598 Ma age range. The Arrikine sill is a high-Ti alkaline gabbro having the geochemical composition of a hawaiite akin to several intraplate continental and oceanic provinces, including the contemporaneous Aïr ring complexes province in Niger, but also to the Mauna Loa volcano in Hawaii. This peculiar composition akin to that of the contemporaneous Aïr province is in agreement with a lower Devonian age for the Arrikine sill.The lower Devonian Arrikine sill emplacement is related to a “Caledonian” transtensive reactivation of the western metacratonic boundary of the Murzuq craton. This event also generated in the Saharan platform the so-called “Caledonian unconformity” of regional extension, the Aïr ring complexes and magmatic rocks that produced sand injections. It could be related to rifting of the Hun terranes that occurred at the plate margin to the north (Stampfli and Borel, 2002, Blackey, 2008 and references therein). The mid-Carboniferous (c. 326 Ma) reactivation corresponds to Variscan compression on NW Africa generating aplitic fluids, but also to the major “Hercynian unconformity” of regional extension. The generation of the Arrikine magma is attributed to partial melting through adiabatic pressure release of uprising asthenosphere along tectonically reactivated mega-shear zones, here bordering the relictual Murzuq craton enclosed in the Saharan metacraton.
ISSN: 0899-5362

hal-01306637
https://hal.archives-ouvertes.fr/hal-01306637
DOI : 10.1016/j.jafrearsci.2015.11.019

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : Tectonics, v. 27, p. TC5011, 2008. http://dx.doi.org/10.1029/2007TC002232
International audience
The seismic activity of the Ligurian Basin, the northeastern termination of the western Mediterranean basin, is larger than in surrounding regions, even though recent geodetic studies attest that this area is subject to very low levels of deformation. This basin is an example of a type of passive margins that cannot be considered solely as inert sites of sedimentation and of progressive subsidence and that are reactivated in a compressive pattern; other examples include the Kwanza basin (Angola) and the Brazil margin. We investigated, by means of 2-D thermomechanical modeling, the structural and rheological heterogeneities that can lead to concentration of strain in this marginal basin. We deduced that the deformation of the basin is due to its particular geometric features, narrow and with a thick surrounding continental crust, related to its position at the southern termination of the Alps. This sharp transition, in terms of both geometry and rheological contrast, is a main factor in explaining the weakness of the margin. We discuss the importance of buoyancy forces versus tectonic forces, as well as thermal effects, on the observed reactivation. Influence of contrast in rheology between an oceanic-type crust and continental crust is also studied. Geodynamical implications are proposed for the region. The good agreement between the predicted localized deformation and the observed seismicity distribution should help improve seismic hazard assessment in the region.
ISSN: 0278-7407

hal-00407859
https://hal.archives-ouvertes.fr/hal-00407859
DOI : 10.1029/2007TC002232

Éditeur(s) : HAL CCSD Taylor & Francis: STM, Behavioural Science and Public Health Titles
Résumé : International audience
The dislocation microstructures in a single crystal of olivine deformed experimentally in uniaxial compression at 1090 °C and under a confining pressure of 300 MPa, have been investigated by transmission electron tomography in order to better understand deformation mechanisms at the microscale relevant for lithospheric mantle deformations. Investigation by electron tomography reveals microstructures, which are more complex than previously described, composed of and dislocations commonly exhibiting 3D configurations. Numerous mechanisms such as climb, cross-slip, double cross-slip as well as interactions like junction formations and collinear annihilations are the source of this complexity. The diversity observed advocates for microscale deformation of olivine significantly less simple than classic dislocation creep reported in metals or ice close to melting temperature. Deciphering mechanism of hardening in olivine at temperatures where ionic diffusion is slow and is then expected to play very little role is crucial to better understand and thus model deformation at larger scale and at temperatures (900–1100 °C) highly relevant for the lithospheric mantle.
ISSN: 1478-6443

hal-01667146
https://hal.archives-ouvertes.fr/hal-01667146
DOI : 10.1080/14786435.2017.1367858

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
[1] Statistical analysis of modern oceanic subduction zone parameters, such as the age of a downgoing plate or the absolute plate motions, is performed in order to investigate which parameter controls the dip of a slab and, conversely, what the influence of slab geometry is on upper plate behavior. For that purpose, parameters have been determined from global databases along 159 transects from all subduction zones that are not perturbed by nearby collision or ridge/plateau/seamount subduction. On the basis of tomographic images, slabs that penetrate through, or lie on, the 670 km discontinuity are also identified. The results of the statistical analysis are as follows: (1) Back-arc stress correlates with slab dip, i.e., back-arc spreading is observed for deep dips (deeper than 125 km) larger than 50°, whereas back-arc shortening occurs only for deep dips less than 30°. (2) Slab dip correlates with absolute motion of the overriding plate. The correlation is even better when the slab lies on, or even more penetrates through, the 670 km discontinuity. (3) Slabs dip more steeply, by about 20° on average, beneath oceanic overriding plates than beneath continental ones. (4) Slabs dip more steeply on average by about 10° near edges. (5) Slab dip does not correlate with the magnitude of slab pull, the age of subducting lithosphere at the trench, the thermal regime of the subducting lithosphere, the convergence rate, or the subduction polarity (east versus west). The present study provides evidence that the upper plate absolute motion plays an important role on slab dip, as well as on upper plate strain. Retreating overriding plates are often oceanic ones and thus may partially explain the steeper slab dips beneath oceanic upper plates. One can infer that low slab dips correlate well with compression in continental advancing upper plates, whereas steep dips are often associated with extension in oceanic retreating upper plates. Excess weight of old slabs is often counterbalanced by other forces, probably asthenospheric in origin, such as lateral mantle flow near slab edges or anchor forces, to determine slab dip. Components: 12,676 words, 13 figures, 1 table.
ISSN: 1525-2027

hal-01261567
https://hal.archives-ouvertes.fr/hal-01261567
https://hal.archives-ouvertes.fr/hal-01261567/document
https://hal.archives-ouvertes.fr/hal-01261567/file/lallemandG32005.pdf
DOI : 10.1029/2005GC000917

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Slices of polycyclic metasediments (marbles and meta-cherts) are tectonically amalgamated with the polydeformed basement of the Dent Blanche tectonic system along a major Alpine shear zone in the Western Alps (Becca di Salé area, Valtournenche Valley). A combination of techniques (structural analysis at various scales, metamorphic petrology, geochronology and trace element geochemistry) was applied to determine the age and composition of accessory phases (titanite, allanite and zircon) and their relation to major minerals. The results are used to reconstruct the polyphase structural and metamorphic histories, comprising both pre-Alpine and Alpine cycles. The pre-Alpine evolution is associated with low-pressure high-temperature metamorphism related to Permo-Triassic lithospheric thinning. In meta-cherts, microtextural relations indicate coeval growth of allanite and garnet during this stage, at ~ 300 Ma. Textures of zircon also indicate crystallisation at HT conditions; ages scatter from 263 to 294 Ma, with a major cluster of data at ~ 276 Ma. In impure marble, U-Pb analyses of titanite domains (with variable Al and F contents) yield apparent 206Pb/238U dates range from Permian to Jurassic. Chemical and isotopic data suggest that titanite formed at Permian times and was then affected by (extension-related?) fluid circulation during the Triassic and Jurassic, which redistributed major elements (Al and F) and partially opened the U-Pb system. The Alpine cycle lead to early blueschist facies assemblages, which were partly overprinted under greenschist facies conditions. The strong Alpine compressional overprint disrupted the pre-Alpine structural imprint and/or reactivated earlier structures. The pre-Alpine metamorphic record, preserved in these slices of metasediments, reflects the onset of the Permo-Triassic lithospheric extension to Jurassic rifting.
ISSN: 0024-4937

hal-00758123
https://hal.archives-ouvertes.fr/hal-00758123
DOI : 10.1016/j.lithos.2012.05.007

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : National audience
Introduction Le cancer du pancréas est une néoplasie souvent diagnostiquée au stade métastatique et au pronostic sombre. Les lésions secondaires pulmonaires, pléiomorphes, sont souvent présentes au diagnostic et peuvent faire découvrir une maladie par ailleurs asymptomatique. Observations Nous rapportons une série rétrospective de trois patientes, âgées de 32 à 74 ans, qui présentaient des images de pneumopathie interstitielle diffuse (PID) ayant conduit au diagnostic de métastases pulmonaires de cancer du pancréas. Pour la première patiente, une sarcoïdose avait été évoquée devant son jeune âge et la négativité des prélèvements écho-endoscopiques digestifs répétés. La deuxième présentait de multiples nodules pulmonaires excavés et un tableau de compression médullaire a conduit à l’obtention rapide du diagnostic anatomopathologique sur les lésions osseuses. Pour la troisième, le terrain de polyarthrite rhumatoïde et l’absence de symptomatologie abdominale faisait rechercher une atteinte en rapport avec son rhumatisme inflammatoire. L’anatomopathologie, sur biopsies pulmonaires pour deux patientes a permis de redresser le diagnostic. Conclusion Devant une PID atypique le recours à des prélèvements invasifs doit être rapide afin de ne pas retarder un diagnostic de cancer, notamment pancréatique
ISSN: 0761-8425

hal-01334066
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01334066
DOI : 10.1016/j.rmr.2016.04.019

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Detrital zircons in metasedimentary rocks attributed to three different complexes in the Central and Pernambuco-Alagoas domains of the Borborema Province, northeastern Brazil, were dated by LA-ICP-MS. Two samples from each of the following complexes were analyzed: Sertania and Surubim, in the Central Domain, and Rio Una, in the Pernambuco-Alagoas Domain. One sample of the Sertania Complex yielded only Paleoproterozoic zircons, whereas Neoproterozoic zircons predominate in the other, with the youngest zircon indicating deposition after 642 Ma. One of the samples of the Surubim Complex yielded, again, only Paleoproterozoic concordant zircon ages. In the other sample, although Paleoproterozoic zircons predominate, ages vary from the Mesoarchean to the Neoproterozoic. The age of the youngest zircon in this latter sample indicates deposition after 850 Ma and an overgrowth on an Archean grain yielded an age of 623 +/- 6 Ma (2 sigma), interpreted as the age of peak metamorphism. The two samples of the Rio Una Complex yielded predominantly detrital zircons with ages in the ranges 2.2-2.1 Ga and 1.7-1.6 Ga. In this complex, the youngest detrital zircon suggests deposition after 917 Ma and metamorphic zircons indicate peak metamorphic conditions between 600 Ma and 617 Ma.;The results of this study, together with available data from the literature, allow the following conclusions: (a) The Sertania Complex is a Neoproterozoic sequence, and not Paleoproterozoic, as previously thought; (b) The similarity in lithological associations, detrital zircon populations and C isotope signature between the Sertania and Surubim complexes suggest that they belong to the same lithostratigraphic unit; (c) Although the Rio Una Complex can be older than the Sertania/Surubim Complex, the lack of zircons younger than 900 Ma can also result from insufficient sampling or absence of young rocks alongside the drainage system that collected detritus to this complex: (d) The regional metamorphism related to the Brasiliano Orogeny attained its climax at 630-600 Ma; (e) The age spectra of detrital zircons require their derivation from erosion of rocks formed not only during known geological events in the Borborema Province and in the nearby Sao Francisco/Congo Craton, but also from the Amazonian Craton, suggesting accumulation in an intracratonic setting within a preexisting large continent: (f) The short timespan between deposition and orogenic deformation may explain the overall medium- to high-temperature metamorphism due to maintenance, in the subsequent compressional event, of the elevated geothermal gradients produced during broad-scale lithosphere extension.
ISSN: 0301-9268

hal-00443856
https://hal.archives-ouvertes.fr/hal-00443856
DOI : 10.1016/j.precamres.2009.09.009

Éditeur(s) : HAL CCSD Springer-Verlag
Résumé : The Chile-Argentina Patagonian Cordillera is a natural laboratory to study the interactions between oceanic and continental lithosphere during the subduction of an active spreading ridge beneath a continent. Subduction of the South Chile spreading ridge, which separates the Nazca plate from the Antarctic plate, started around 15–14 Ma at the southern tip of Patagonia. Presently, the southernmost segment of the Chile Ridge enters the Peru-Chile trench at 46°S, at the site of the Chile Triple Junction (CTJ). We review the main events which occurred on land in the CTJ region (46–47°S), related with processes of ridge subduction. We summarize tectonic, sedimentary, and magmatic features in a 30 Ma-to Present chronological table. A preridge subduction stage, from 30 to 15 Ma, is characterized by the onset and growth of Patagonian relief and by a shift from marine to continental detrital sedimentation in the foreland at 20–22 Ma. The change from pre-ridge subduction to ridge subduction is marked on land by a transition from calc-alkaline to alkaline volcanism, at 14–12 Ma, and by the onset of eruption of very large fl ood basalt provinces (future volcanic plateaus) following rapid erosion of the eastern foreland belt. Post-plateau basaltic volcanism (<4 Ma) is coeval with a period of tectonic and morphological rejuvenation during which the eastern foreland of the Cordillera has been affected by extensional/transtensional tectonics. We place these events in the framework of a tectonomagmatic model involving the opening of slab windows due to both slab tear and ridge axis subduction.
Subduction Zone Geodynamics

hal-00421053
https://hal.archives-ouvertes.fr/hal-00421053
DOI : 10.1007/978-3-540-87974-9_12